Search Documents

By S. J. McCarroll

THE Three Kids mine, some six miles east of Henderson, Nev., is in a typical southwest desert area, with high dry summer heat and cool to cold winter seasons. The manganese deposit was located during World War I.1 During this period 15,000 to 20,000 tons of ore assaying up to 41 pct manganese were shipped. Interest in the deposit was not revived until the middle thirties, when experiments on the ore were initiated. Test work indicated possible recovery of only 70 pct by flotation, but in 1941 additional work was done at the Boulder City pilot plant of the U. S. Bureau of Mines and also by M. A. Hanna Co. As a result, the Manganese Ore Co. was formed and a plant utilizing the SO, process was constructed. Numerous operation difficulties ensued, and the plant was closed when the manganese situation in the country eased.

Jan 3, 1954

By H. C. Stumpf, L. A. Willey, V. L. Fink

Very few studies of the aluminum-sodium system have been reported. Heycock and Neville1 were unable to detect any solubility of sodium in liquid aluminum. Mathewson2 prepared an equilibrium diagram consisting of two horizontal lines at the melting points of the two metals. He was unable to detect solubility at either end of the system. Scheuer3 first developed a method for the chemical determination of sodium in aluminum and then studied the solubility of sodium in liquid aluminum. His method involved heating aluminum with excess sodium under hydrogen until the two liquids were at equilibrium, chilling the melt, and analyzing the aluminum-rich layer. He reported the solubility to be 0.10 pct sodium at 700°C, 0.115 pct at 750°C, and 0.128 pct at 800°C. This paper on the aluminum-sodium system is the twenty-first in a series from the Aluminum Research Laboratories describing equilibrium relations in aluminum alloy systems. Materials The alloys for this investigation were prepared from electrolytically refined aluminum (99.99 pct) and sodium of reagent quality conforming to specifications of the American Chemical Society. Chemical analysis of the aluminum showed the fol- lowing impurities: 0.002 pct Si, 0.002 pct Fe, 0.002 pct Cu, <0.001 pct Mn, 0.002 pct Mg and 0.001 pct Na. The sodium content of all alloys was determined by either chemical or spectro-graphic standard procedures5 No. IIA and No. SI I respectively. Determination of Miscibilitv The boundary of the miscibility gap was determined by a modification of the method of Scheuer3 and of that used by Henry and Cordiano. As finally developed the method was as follows: A fused alumina crucible 25 mm id with 75 mm depth and 1.5 mm wall thickness was placed on the bottom of a container made from a 4-in. length of 1 1/2-in. iron pipe and pipe caps. ?&apos;he space around the sides of the crucible was filled with 40 mesh crystalline alun-dum. A charge of 60 g of aluminum and 10 to 15 g of sodium was placed in the crucible, the sodium first being trimmed and rinsed with iso-pentane to remove kerosene. The container was tightly capped, filled with argon (99.6 pct pure), and heated to the desired temperature (between 670 and 800°C). A positive pressure of argon (about 8 mm of mercury) was maintained through a small pipe to the upper cap. After soaking for from 2 to 5 hr, the container was quenched by directing a stream of water onto the base, so that solidification of the aluminum-rich layer was rapid and essentially unidirectional. Analyses were made on drillings taken from the bottom of the ingots after machining off the surface layers. Pre-

Jan 1, 1949

By L. P. (Les) Haldane

Building a small underground coal mine is a risky endeavor, especially in the recent economic environment. ARCO&apos;s Mt. Gunnison No. 1 Mine, located in western Colorado, was designed and built as a small expandable speculation mine with initial production to be sold on the spot market, so it was very important to minimize capital exposure. This mine, operated by West Elk Coal Company, a subsidiary of Anaconda Minerals, was successfully built under budget at $35 million, and has been operating successfully since completion of construction in late 1982. The initial planning phase of a project is extremely important for testing the economic and technical feasibility of a proposal. The construction phase, by contrast, carries with it significant cost and quality risks which can relate to long-term economic and operating problems and therefore directly affect the viability of the project. This paper discusses several different aspects of the cost overrun risk involved in building an underground coal mine, and how attempts were made to minimize these risks during construction of the Mt. Gunnison Mine. Good people, construction planning, and execution are essential factors in assuring a quality, cost-effective project, with corresponding risk minimization during the construction phase and long term favorable implications for the operating phase.

Jan 1, 1985

By Jan D. Miller

The application of computers to the control and study of mineral processing operations such as grinding, classification and flotation has created an interest in simulation studies of these operations with mathematical models. Evidence of this interest is confirmed by papers presented at the 1969 International Computer Application Symposium held concurrently with the Fall Meeting of the Society of Mining Engineers in Salt Lake City, September 17-19, 1969. Proceedings of this symposium, entitled A Decade of Digital Computing in the Mineral Industry. were edited by Alfred Weiss and published by SME. Two sections of this book are devoted to computer application and simulation of mineral processing operations. In the area of comminution, several papers were presented at the International Computer Symposium. The size-discretized batch grinding model was described, and its application to the simulation of batch grinding, locked-cycle grinding and closed circuit grinding were discussed1. Freeh, Horst and Kellner2 approached simulation using a steepest ascent parameter-fitting technique, while Schoner3 considered the dependence of the elements of the mill matrix and classifier matrix on operating conditions, especially the feed rate.

Jan 1, 1970

By Samuel G. Lasky

In a recent discussion of the mineral resource position of the United States, published in the September 1946 issue of Mining and Metallurgy, I expressed my conviction that ore deposits of major magnitude remain to be found in this country and that they can be found without undue cost or risk. I stated with equally strong conviction, however, that if the search for such deposits is to be notably successful there must be, among other things, a reorientation of philosophy and mental habits on the part of many who would be connected with the search. I would now like to enlarge upon that statement. For such a purpose. we may consider that the search for concealed deposits involves four steps: (I) the selection of areas for further study; (2) the geologic study of those areas in order to verify their general favorableness and in order to choose specific patches worthy of being tested; (3) the decision whether exploration of the patches chosen should actually be undertaken; and (4) the exploration itself. The first two steps and the last rest upon the judgment and skill of geologists. The third step—the decision whether exploration should be undertaken—rests upon management. In my opinion, the philosophies or principles that have guided these steps in the past are now inadequate. Philosophy of Appraisal If concealed deposits are to be looked for, how are the places of their possible concealment to be recognized? Every known mineralized area still in the prospect stage has already been repeatedly examined and condemned. As for those deposits concealed under later rocks, there may be not even the clue of a near-by outcrop for engineer or geologist to consider. flow then, are we to know where to look? Geologic Probability In the early days of our mining industry, ore deposits were found mainly by "following the ore." Later, as such opportunities decreased, and as geologic concepts became accepted, deposits were found more and more through use of the notion of geologic probability. Many instances can be cited wherein a courageous operator ignored the implications of the unsuccessful efforts of predecessors and, solely by "following the ore," converted a discredited prospect into a good mine. Similar experience doubtless will occur in the future, but "following the ore" will no longer in itself find new deposits in the amount needed. Nor can enough new ore be expected from further use of the notion of geologic probability, for, as mentioned above, our known prospects have already been ex-

Jan 1, 1949

By Samuel G. Lasky

In a recent discussion of the mineral resource position of the United States, published in the September 1946 issue of Mining and Metallurgy, I expressed my conviction that ore deposits of major magnitude remain to be found in this country and that they can be found without undue cost or risk. I stated with equally strong conviction, however, that if the search for such deposits is to be notably successful there must be, among other things, a reorientation of philosophy and mental habits on the part of many who would be connected with the search. I would now like to enlarge upon that statement. For such a purpose. we may consider that the search for concealed deposits involves four steps: (I) the selection of areas for further study; (2) the geologic study of those areas in order to verify their general favorableness and in order to choose specific patches worthy of being tested; (3) the decision whether exploration of the patches chosen should actually be undertaken; and (4) the exploration itself. The first two steps and the last rest upon the judgment and skill of geologists. The third step—the decision whether exploration should be undertaken—rests upon management. In my opinion, the philosophies or principles that have guided these steps in the past are now inadequate. Philosophy of Appraisal If concealed deposits are to be looked for, how are the places of their possible concealment to be recognized? Every known mineralized area still in the prospect stage has already been repeatedly examined and condemned. As for those deposits concealed under later rocks, there may be not even the clue of a near-by outcrop for engineer or geologist to consider. flow then, are we to know where to look? Geologic Probability In the early days of our mining industry, ore deposits were found mainly by "following the ore." Later, as such opportunities decreased, and as geologic concepts became accepted, deposits were found more and more through use of the notion of geologic probability. Many instances can be cited wherein a courageous operator ignored the implications of the unsuccessful efforts of predecessors and, solely by "following the ore," converted a discredited prospect into a good mine. Similar experience doubtless will occur in the future, but "following the ore" will no longer in itself find new deposits in the amount needed. Nor can enough new ore be expected from further use of the notion of geologic probability, for, as mentioned above, our known prospects have already been ex-

Jan 1, 1949

By H. H. Uhlig

A study of passivity in chromium-iron alloys holds considerable interest, both because of the present-clay practical importance of the stainless steels, and because of the scientific importance attached to the mechanism of their corrosion resistance. Upon the discovery of the passive chromium-iron alloys in 1912, it seemed logical to attribute the observed phenomenal corrosion resistance to a thin, continuous, protective reaction product on the surface. The product was thought to be Cr2O3 or a similar oxide containing both chromium and iron. This mechanism seemed likely in view of Michael Faraday&apos;s conjecture that passive iron is not reactive in concentrated nitric acid because of an oxide on the metal surf ace. Since 1912, data have accumulated that permit a further exploration into the nature of passivity and provide a new approach to the problem. A summary of the facts lends considerable weight to a mechanism based not on physical protection of an oxide or similar compound, although such compounds may be present on the surface, but to a change in tendency of surface metal atoms to react chemically. This change in reaction tendency is ascribed to chemisorbed films that effectively satisfy residual valence forces of the metal surface, but do not appreciably disturb the positions of metal atoms in the lattice. In other words, formation of a new lattice such as that of an oxide is not a necessary condition for this type of passivity. The decreased reaction tendency of the metal by reason of chemisorbed films can thereby account for low reaction rates of the stainless steels in many media, as well as a noble galvanic potential as is observed. Substances capable of adsorbing on the stainless steels, and hence accompanying the property of passivity, are typically oxygen, nitrites or chromates, but are not in any sense limited to these. Other elements and compounds can also chemisorb, and therefore may also play a major part in the mechanism of passivity in specific media. The mechanism of passivity based on chemisorption or activated adsorption begins with the interpretation Langmuir proposed for his experiments concerning adsorbed oxygen on tungsten.&apos; He found that adsorbed oxygen was tightly bound, remaining on the tungsten surface above temperatures at which WO3 rapidly volatilizes. The oxygen in such a state did not readily react with hydrogen even at

Jan 1, 1949

By J. Ellzey Hayden, Lucien Eaton

The Cliffs Shaft mine of the Cleveland Cliffs Iron Co., located in the city of Ishpeming, Mich., is the largest producer of hard hematite ore on the Marquette iron range. The two shafts, A and B, lying 820 ft. (250 m.) apart on the east-west trend of the ore formation, were sunk in the early eighties, and, except for four years, have been steady producers of iron ore. Their location, on a hill overlooking the general offices of the company on the one side and the city of Ishpeming on the other, has made the shaft houses landmarks. In the spring of 1919, as the old wooden shaft houses had become shaky and out of line, and would soon be unsafe, it was necessary to replace them with the least possible delay. Three plans of construction were, therefore, considered: To replace the old shaft houses by somewhat similar structures made of wood; to use steel and radically change the design; or to build reinforced-conerete shaft houses outside of the wooden structures, completely enclosing them. The first plan was disapproved, because it is anticipated that the mine will have a long life and the proximity of other buildings makes the danger from fire rather great. Delay in receiving material, and the necessity for closing the shafts during erection, were other factors in the situation. The second plan was disapproved on account of the high cost of steel, slow delivery, and interference with hoisting during the period of erection. The presence near one of the shafts of a large bed of hard gravel suitable for concrete made the cost of the third plan considerably less than the second, and little, if any, delay in hoisting was expected. Our expectations in this regard were fully realized. Furthermore, the work could be done by unskilled labor, which was plentiful, and the erection could be quickly started. When the proposition was submitted to W. G. Mather, president of the company, he recommended that, on account of the prominence of the buildings due to their location, an effort should be made to combine in the design as far as practicable something of architectural beauty. Following his recommendation, the original plans were submitted to the

Jan 1, 1922

By M. C. Leverett, W. B. Lewis

The dynamic behavior of a multiple fluid system is completely describable in terms of driving forces and resistances to flow. The latter are proportional to the viscosity of the fluid under consideration and inversely proportional to a property of the system termed the " effective permeability " to that fluid, a property therefore defined by this relation. Since three phases are usually present in oil reservoirs, it is essential to know the effective permeabilities to the several fluid phases, and the relationship between the composition of the fluid in the pore space and that of the flowing stream, in order to handle satisfactorily certain problems of oil production. In this regard, there are many unknown factors and parameters, and many that can be evaluated only indirectly. However, it is expected that work along lines similar to this present undertaking will help materially in solving these problems. .. . . Previous workers in this field have investigated the two-phase systems, water-gas,&apos; water-oil2 in unconsolidated sands, and water-gasg in consolidated sands. The extension of the study of the flow of heterogeneous fluid systems from two to three phases involved only slight changes in technique. The apparatus used in the present work, except for slight changes to be described, was that used by Leverett in his water-oil experiments.~ Correlation and interpretation of data were made by methods analogous to those used in two- phase work. The relative permeability to a phase—the effective permeability divided by the permeability of the system to a homogeneous fluid—was employed throughout in correlating the rate of flow of that phase with the composition of the pore space. Quantitative measurements of two independent physical properties of the system were required to determine the composition of the pore space. As in the two-phase work, the fraction of water was determined electrically, The gas fraction was determined by measuring changes in volume accompanying measured pressure changes. Suitable account was taken of the solubility of the gas in the liquid phases, and of the vapor pressure of the water phase. Since this work was exploratory in nature, no attempt was made to obtain highly accurate numerical results. Reasonable precision and reproducibility were sought. Experimental Procedure variables Considered.—Of the properties of the fluids, the oil viscosity is most likely in practice to vary widely. Variations in oil viscosity were therefore included in this work, but variations in other properties of the fluids are as yet unexplored. It appears unlikely that the normally encountered variations will produce significant changes. ~h~ observations were made at fairly high pressure gradients, no attempt being made to detect a variation of the relative permeabilities with pressure gradient. It should be pointed out also that since most of the data were taken on one sand size only, it call Only be assumed at present that changes in

Jan 1, 1941

By W. B. Lewis, M. C. Leverett

The dynamic behavior of a multiple fluid system is completely describable in terms of driving forces and resistances to flow. The latter are proportional to the viscosity of the fluid under consideration and inversely proportional to a property of the system termed the " effective permeability " to that fluid, a property therefore defined by this relation. Since three phases are usually present in oil reservoirs, it is essential to know the effective permeabilities to the several fluid phases, and the relationship between the composition of the fluid in the pore space and that of the flowing stream, in order to handle satisfactorily certain problems of oil production. In this regard, there are many unknown factors and parameters, and many that can be evaluated only indirectly. However, it is expected that work along lines similar to this present undertaking will help materially in solving these problems. .. . . Previous workers in this field have investigated the two-phase systems, water-gas,&apos; water-oil2 in unconsolidated sands, and water-gasg in consolidated sands. The extension of the study of the flow of heterogeneous fluid systems from two to three phases involved only slight changes in technique. The apparatus used in the present work, except for slight changes to be described, was that used by Leverett in his water-oil experiments.~ Correlation and interpretation of data were made by methods analogous to those used in two- phase work. The relative permeability to a phase—the effective permeability divided by the permeability of the system to a homogeneous fluid—was employed throughout in correlating the rate of flow of that phase with the composition of the pore space. Quantitative measurements of two independent physical properties of the system were required to determine the composition of the pore space. As in the two-phase work, the fraction of water was determined electrically, The gas fraction was determined by measuring changes in volume accompanying measured pressure changes. Suitable account was taken of the solubility of the gas in the liquid phases, and of the vapor pressure of the water phase. Since this work was exploratory in nature, no attempt was made to obtain highly accurate numerical results. Reasonable precision and reproducibility were sought. Experimental Procedure variables Considered.—Of the properties of the fluids, the oil viscosity is most likely in practice to vary widely. Variations in oil viscosity were therefore included in this work, but variations in other properties of the fluids are as yet unexplored. It appears unlikely that the normally encountered variations will produce significant changes. ~h~ observations were made at fairly high pressure gradients, no attempt being made to detect a variation of the relative permeabilities with pressure gradient. It should be pointed out also that since most of the data were taken on one sand size only, it call Only be assumed at present that changes in

Jan 1, 1941

By F. C. Sturges

For some time mining engineers have been interested in the possibility of using small diameter shafts, sunk by core drilling, as aids to ventilation and as emergency escapeways. The possibilities are interesting to contemplate, but new methods involve unknowns, and interest tends to remain passive until these unknowns are, solved. Recently we have completed two 36-in. diam core drilled shafts, and wish to make the data on these available to the industry. Both shafts were drilled for the McLain Fire Brick Co., one at its Buckeye mine and the other at its Colonial mine. Both mines are in the fireclay underlying the Lower Kittanning coal. Both mines have been in operation for a number of years and have required expensive maintenance work on return airways. It was decided that considerable savings could be effected by short-circuiting the air to the surface through small shafts. It was also realized that these holes, located near the present workings, would be of added value as emergency escapeways. Originally, 48-in. diam shafts were considered, but actual computations showed 36-in. diam shafts were more than ample at both mines. The shaft at the Buckeye mine is 240 ft deep, and that at the Colonial mine 258 ft deep. Both holes were started in the lower part of the Conemaugh formation and penetrated Conemaugh and Allegheny strata. The holes were started through the unconsolidated materials overlying bedrock by constructing a concrete collar with a wall thickness of 8 in. Then the shafts were drilled by the shot-core drill method. An annular groove was cut in the rock by the abrading action of chilled steel shot run under the shoe of the core barrel. The drilling was done in stages, the core barrel drilling the groove for a certain distance depending on conditions encountered, and then the cores broken off and taken out in sections. The core barrel had a 36-in. o.d. and the finished diameter of the shaft measured almost 37 in. The major questions that could not be answered until the completion of the first shaft were, (I) how much ground water would be encountered, how would it hinder the drilling, and how difficult would it be to seal off, and, (2) how would the walls of the hole stand up. The holes of course could .be cased or lined, but that is considerable added expense in any shaft.

Jan 1, 1949

Jan 1, 1968

By T. P. Papazoglou, N. A. D. Parlee, W. C. Phelps

PRACTICAL designs for good "home made" molybdenum furnaces are hard to find in the literature. The one described briefly below left something to be desired but was good enough to operate as a rather long (30 in.) two-zone furnace for periods of over 2 months at temperature (1400° to 1600°C) without shutdown. The principal problem in our application was to establish a temperature profile with two distinct constant-temperature zones and no dip between the zones. This and other problems mentioned below would not arise, however, if both zones were operated at the same temperature and if a shorter furnace were acceptable. Since molybdenum windings oxidize very rapidly when heated in air, impervious refractory tubes were used for both the furnace core and the outer jacket tube shown in the accompanying figures. A protective atmosphere of forming gas (10 pct H2, 90 pct N2) was continuously passed through the gas-tight annular volume between the core and outer jacket. The water-cooled copper ends shown in Figs. 1 to 3 sealed the ends of the tubes. Annealed molybdenum wire (40 mil) was wound on the recrys-tallized alumina core (35.5 mm OD by 28.5 mm ID by 30 in.) at a spacing of 0.36 in. The spacing was reduced to 0.29 in. close to the ends to partially compensate for end heat losses. Fig. 2 shows two molybdenum-ground lead taps off the center of the winding to produce the two independect temperature zones. The ground lead was insulated with 1/4-in. alumina tubing and connected to the grounded copper end by passing the wires through the gas port tube and crimping each wire into notches cut at the mouth. To prevent sagging of the core at high temperatures, refractory "troughs" were cut from alumina and mullite tubing to cradle the core. The support "troughs" which were 6 in. long and located about 5 in. from each end of the annular volume also served as radiation shields. In view of the different expansion coefficients and operating temperatures of the core and outer jacket (3.5 in. OD by 3 in. ID by 30 in.), the ends of the tubes were smoothed and squared to produce good sealing surfaces, and the core was ground 1/32 in. shorter than the outer tube. The power terminals were passed through their respective conductor ports which were internally lined with alumina tubing and sealed with Armstrong adhesive A-6 leaving about 1 in. of protruding lead wire for external connections. (Adhesive A-6 is a two-component system consisting of an epoxy-type resin with a mineral fibrous filler and an amine catalyst.) Figs. 1 and 3 show the entire assembly of concentric refractory tubes, copper ends, and sealing o rings, held together with two brass flanges and 3/8-in. bolts with heavy springs for dimensional flexibility. The furnace shell (19 by 19 by 30 in.) consisted of a steel frame with sheets of transite forming a box. The copper ends protruded through two 3.75-in. circular holes cut at the center of each transite square end. Thermal insulation next to the transite exterior was effected by K-23 B&W bricks alld in a central volume of approximately 9 by 9 by 30 in. a row of K-30 bricks was lined up to support the hot assembly. The rest of the volume around the outer

Jan 1, 1965

By D. M. McFarland

A FEW years ago a novel electric detonator known as the split-second or millisecond delay electric blasting cap was introduced for use in quarry blasting. Regular electric blasting caps fired in series may be depended upon to fire within a millisecond or so from the first to the last in a series. Regular delay electric blasting caps are provided that fire one period after the other period in intervals of 1/2 to possibly 1 l/2 sec. Most split-second or millisecond delays are designed to fire one period after the other period in possibly 25 to 50 millisecond intervals. The ear is not capable of detecting time intervals of this magnitude.

Jan 11, 1950

By Jack Washburn

The c axis indentations in zinc crystals were shown to undergo 100 pct strain recovery on heating. The mode of deformation and the details of the polygonization and collapse of indentations were found to be consistent with a number of predictions of dislocation theory. IT has been observed that indentations of the type made by Jillson in zinc crystals can, under certain conditions, be macle to shrink in size and even completely disappear on heating the crystal, Fig. 1. The details of the process are interesting in that they afford a simple experimental illustration of several predictions of dislocation theory. The indentations were made as shown in Fig. 2 by dropping a 0.2 g indenter with a hemispherical point on a cleavage face of a. zinc crystal. Such indentations can be made through relatively great thicknesses in the c-axis direction. The material close to the struck surface, where mechanical twinning and complex distortion occurred, was removed by cleavage. The remaining crystal, which was about 1 cm thick, contained a dent that was accurately round and almost the same size on both top and bottom surfaces. The indentation had the form of a flat cone of half angle approximately 89°, having a rounded apex and a rounded intersection with the unde-formed part of the crystal. The mode of deformation was primarily slip on the three equivalent systems in the basal plane. Six types of dislocation loop (plus and minus in each of the three directions) as shown in Fig. 3 are required by the geometry of the indentation. The maximum shear strain in the radial direction amounted to approximately 2.5 pct. Slip was distributed in the usual, microscopically nonuniform, manner among the possible parallel slip planes. When an indentation was made close to a (2110) surface, three separate sets of interpenetrating slip bands appeared as shown schematically in Fig. 3. A small biaxial tension strain in the plane of (0001) is also a geometrical necessity for the formation of an indentation. If the sides of the dent are tilted l° with respect to the undeformed surrounding crystal, and the surround-

Jan 1, 1957

By Alfred Boyles

THE experiments described below are a continuation of work on the graphitization of cast iron conducted as part of the program of funda-mental research at Battelle Memorial Institute. In previous work it was found that melting in hydrogen increased the amount of eutectic and in others i produced al marked changes in the size of the graphite flakes. These effects seemed to be III sulphur and manganese present in the material studied. Iron-carbon- respond silicon alloys did same manner as mg cast iron and there was no evidence to show that hydrogen was able to stabilize the carbide in such alloys unless additions of sulphur were made. The two alloys examined contained about 2 per cent of FIG. 1.-APPARATUS FOR MELTING UNDER PRESSURE. silicon. The present paper is con- A, inlet for gas. cerned with alloys of lower silicon B, outlet for evacuation. content and describes the structural C, power lead. D thermocouple changes produced by melting in E, plug for access to furnace. various atmospheres at pressures F, crucible. ranging from a partial vacuum up to 300 lb. per sq. inch.

Jan 1, 1939

By W. C. Hagel, H. J. Beattie

Variations in the secondary phase reactions of six nickel-and cobalt-base alloys were determined as a function of solu-tioning from 1700" to 2200°F and aging at 1200" to 1800° F for times up to 1000 hr. Room-temperature impact energies and hardnesses were also measured. Precipitation hardening of these alloys results mainly from the grain-interior formation of ? &apos;; M23C6 appears principally as grazn-boundary cells which can be eliminated by intermediate high-temperature aging treatments. Cellular precipitation of ?&apos; occurs up to 1500°F in cobalt-nickel alloys devoid of chromium, where precipitation by this mode can be attributed to a large degree of lattice disvegistery. THE usefulness of nickel- and cobalt-base alloys is dependent on balancing the strength and ductility provided by the solid-solution matrix, dislocation-type subboundaries, grain-boundary phases and genera1 precipitation within individual grains. Since equilibrium relationships for complex austenitic alloys are not easily fixed, a satisfactory balance

Jan 1, 1960

By Theodore Simons

(Butte Meeting, August, 1913.) DURING the last half century a great amount, of ingenuity and energy has been devoted to the invention of appliances for the recovery of valuable minerals from very fine sands and-slimes. The reason for this is that in almost every, dressing plant the greatest losses of values, considered relatively as well as absolutely, occur in the treatment of slimes. The natural aim of mill operators to minimize these losses has in recent years received another impetus,, from the fact that the gradually diminishing occurrence of high-grade ores makes a more intense recovery of values from existing resources absolutely necessary for profitable operation. The results of such attempts are found in the appearance of a great number of machines and appliances which make it profitable to-day to rework old dumps, containing the tailings of older processes. A constantly growing difficulty of obtaining skilled labor and the increase in wages made it prohibitory to employ those types of machines which required much attention, and in the middle of the nineteenth century the various concentrating tables of the percussion type, which automatically discharge their products, began to take the .place of the intermittent tables, on which, when the bed had reached a certain thickness, operation had to be stopped in order to allow the skimming by hand of the separate layers formed on the table. In the course of. years, two general types of machines evolved for the treatment of fine sands and slimes :- The so-called concentrators and vanners, on the one hand, and the huddles and round tables on . the other.1 For the profitable treatment of the very finest slimes, round tables have as a last resort proved more satisfactory and economical than other machines.

Jan 7, 1913

By W. F. Holbrook, C. E. Wood, E. P. Barrett

THE high-frequency laboratory induction furnace with a rotating liquid crucible enables research workers to conduct certain investigations heretofore very difficult or impossible to realize because vessels are not obtainable that are capable of resisting the physical conditions or the chemical actions to which they are subjected. Applications for patents covering commercial uses of centrifugal liquid crucibles were filed in the United States in 1919,1 in France in 1925, in the United States and Germany in 1926,2 and in France in 1927.3 In 1928, Schuette and Maier,4 of the Bureau of Mines, reported the construction of a whirling table beneath a high-frequency induction furnace. SHAPE AND SIZE OF CENTRIFUGAL LIQUID CRUCIBLES When a vessel containing a liquid is rotated, the inner surface of the liquid takes the shape of a paraboloid under the simultaneous action of centrifugal force and gravity. The internal dimensions of the paraboloid rotating liquid crucible are governed by the diameter of the container and .its speed of rotation. Melted Wood&apos;s metal was poured into cylinders 2 1/2 in. in diameter, which were rotated at 180, 300, and 468 r.p.m. When the metal was solid, a slurry of plaster of Paris was added, and rotation continued until the plaster had set. Fig. 1, a photograph of sections of the cylinders, shows the effect of speed of rotation of the containers upon the shape of the inner surface of the rotating liquid crucibles. TYPES OF FURNACES Three types of high-frequency induction laboratory furnaces using liquid-metal crucibles were designed and constructed by the Blast

Jan 1, 1938

By T. Airaksinen, R. T. Hukki

A new static pneumatic classifier for the primary separation of the feed material for microclassification is discussed. Pilot plant test results and a novel flowsheet for microclassification at the industrial scale are presented.

Jan 1, 1980