Search Documents

COLUMBIA SECTION Holds four sessions during year. Annual meeting in September or October. S. S. FOWLER, Chairman, J. C. HAAS, Vice-Chairman, LYNDON K. ARMSTRONG, Secretary-Treasurer, 720 Peyton Bldg., Spokane, Wash. W. H. LINNEY, J. F. MCCARTHY. A special meeting of the officers of the Columbia Section was held in Spokane, Wash., Jan. 10, 1918, for the purpose of organizing and nominating members to the principal committees of the Section. Present: J. C. Haas, Vice-chairman; W. H. Linney, Past Chairman; and L. K. Armstrong, Secretary. J. F. McCarthy, Wallace, Idaho, was appointed fifth member of the Executive Committee. The following were appointed to the Membership Committee: R. M. Betts; for Oregon; W. J. Hall, for Idaho; J. M. Porter, for Washington. A member for British Columbia will be appointed later. The following were appointed to the Committee on Papers: Prof. F. A. Thomson, Moscow, Idaho; Prof. L. 0. Howard, Pullman, Wash.; H. S. Lee, Rye Valley, Ore. A fourth member, representing British Columbia, is to be appointed later. The following members were appointed representatives on the Executive Committee of the Spokane Engineering and Technical Association: J. C. Haas, W. H. Linney, F. A. Ross, L. K. Armstrong. The Treasurer reported a deficit, resulting from the participation of the Section at the Northwest Mining Convention in 1916. It was recommended that the Institute be petitioned to make good this deficit, in addition to the usual annual allowance. The members of the committee who were present expressed their desire to be of greater service in the present war, and discussed at some length the possible means of carrying out their desires. It was later decided to reopen the subject at a subsequent meeting of the Section, or to present it to the Executive Committee of the Spokane Engineering and Technical Association for discussion and cooperative action. L. K. ARMSTRONG, Secretary.

Jan 3, 1918

This story of the salting of a supposed diamond mine is a part of our Western history and deserves to be recorded in this book. It was more than a local affair, because it was concerned with persons in London and New York, as well as San Francisco. Part of the story has been told by Asbury Harpending in a little book published 12 years ago. Harpending (who died at New York in 1923) was in London in March, 1872, when he received a cable dispatch from William C. Ralston, the president of the Bank of California, stating that "a vast diamond field" had been discovered "in a remote section of the United States". Before starting for San Francisco, Harpending had an interview with Baron Rothschild, who showed a lively interest in the story, which was as follows: two weather-beaten prospectors went to the Bank of California and deposited some uncut diamonds and rubies for safe keeping; these precious stones were estimated to be worth $125,000. The men said that they had found the gems in "a desert portion of the West". They departed quietly, but the story was told in business circles; whereupon George D. Roberts, a mining engineer of wide experience and an associate of Ralston, sought an interview with the prospectors. One of them proved to be a man that had been in the employ of Roberts. Both prospectors, named Slack and Arnold, appeared "coy and cautious"; they were "simpleminded fellows", and were "afraid to trust anyone with the momentous secret ". They refused to divulge the place of discovery and declined "to part with their rights", but later "they became more amenable to reason" and expressed willingness to sell a half interest to

Jan 1, 1932

By D. L. Harris, A. M. Gaudin

THE following results, presented here in condensed form,1 were obtained in a preliminary study of the adsorption of n-hexane thiol, hexyl mercaptan, on sphalerite, zincite, willemite, and quartz, from aqueous solution and from a gas. Interest in this subject was aroused by a Belgian report2 of effective use of hexyl mercaptan for flotation collection of oxidized zinc minerals. The relatively low boiling point, 149°C, of the mercaptan3 suggested the desirability of extending the usual measurements of partition of collector between aqueous solution and gas and between gas and mineral. It is believed that this paper presents the first measurements of this type on a flotation system. Attempts were made to carry out the measurements at equilibrium, but as the work progressed it became increasingly doubtful that this desirable condition had been achieved. To control composition and extent of the gas phase, the apparatus was a wholly-enclosed thermally-controlled glass system. Because of these constraints and the desirability of dealing with pure minerals, a scale of operations was chosen in which a few grams of deslimed mineral were used in each test. It was also necessary to choose a particularly sensitive method for mercaptan analysis, and in fact a method that would permit the experimenters to follow the approach to equilibrium. For these reasons mercaptan marked by radiosulphur 35 was used. An analysis was made for the radiosulphur by a modification of the method of Gaudin and Carr.4

Jan 9, 1954

By Victor Homerberg

A STUDY of the correlation of the mechanical properties, and of the microstructure with the heat treatment of 60-40 brass has been confined, heretofore, to the rolled or extruded material as received from the manufacturer. The results obtained by Babson and Buhler,1 Bengough and Hudson,2 Stead and Stedman,3 and Brayton4 have been confined to the treatment of the material as received. No attempt was made to get the material into a given condition and then to work from this basis. To start with a given structure would have the decided advantage of making the work independent of the original condition, hence, to make the results reproduceable. In a previous paper, it was shown, in connection with the study of the transformation that occurs at about 470° C., that if specimens were quenched to produce the beta structure and then reheated, the beta would begin to break down, at approximately 200° C., into a very finely divided alpha. It was predicted that important results might be obtained if test pieces were to be given a similar double heat treatment and then tested for the mechanical properties as well as a study of the microstructure. The material used in the present investigation was a ¾ -in. round bar of extruded muntz metal of the following composition: Copper, 61.05 per cent.; zinc (by difference), 38.90 per cent.; lead, 0.05 per cent.; iron, trace; tin, nil.

Jan 3, 1924

By H. S. Martin

ALTHOUGH it was known some years ago at the- Utah Copper Co. mills that fine grinding improved flotation recoveries, no accurate data were available until recently as to just how far the grinding could be carried economically. In 1923 the ultimate degree of fineness for flotation feed was supposed to be about 10 per cent. on 65 mesh, with approximately 55 per cent. through 200 mesh, which meant that most of the mineral would pass 100 mesh. At this time Garfield and Wilfley tables were used ahead of flotation and a good deal of the coarse mineral removed prior to the ball mill regrind. Shortly afterwards, mill-scale tests developed the fact that on a feed containing not over 10 per cent. +65¬mesh material flotation alone would give a copper recovery equal to that obtained by the combination of tables and flotation, but that on much coarser feed the recovery with flotation alone was lowered. This was at a time when all the sulfide minerals were floated if possible, so that the only requisite was to grind fine enough to free the mineral from gangue. EARLIEST USE op MICROSCOPIC EXAMINATION OF TAILINGS As early as 1921, the writer had attempted to determine by chemical analysis the relative proportions of copper minerals in tailings from an ore that made extremely poor flotation results. Chemical analysis was not satisfactory or conclusive, and samples of these tailings were sent to the U. S. Bureau of Mines Station at the University of Utah for micro-scopic examination. The question at that time was to determine, if possible, which copper minerals had been lost and why, but R. E. Head, in his report, revealed other interesting data. He said in part: Briefly stated, the mineral particles or grains may be classified into separate groups as follows: 1. Free grains of pyrite, chalcopyrite, chalcocite and bornite, respectively, which contain no other included sulfides; 2. Grains in which all three of the copper sulfides are represented (the core may he of chalcopyrite, partially altered to bornite, these two minerals being entirely surrounded by a shell of chalcocite); 3. Grains composed of equal amounts of bornite and chalcocite or chalcopyrite and chalcocite.

Jan 1, 1929

TO THE BOARD OF DIRECTORS, AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS: Gentlemen.-I have the honor to present the following report of the President for the year 1919. In order that this report may be printed and distributed to the members in advance of the February meeting, it is necessary that it end with the calendar year 1919. Any activities during the first six weeks of 1920 will be covered in the Secretary's report for the year 1920. VISITS TO MEMBERS Your President has visited each of the Local Sections of the Institute, with the exception of the ones at Washington, D. C., Tulsa, Okla., and the Nevada Section. These three sections have not arranged meetings at which the President could be present. In addition, your President, accompanied by President Jennings and Secretary Stoughton, in the year 1918, attended meetings of members in Minneapolis and Duluth, Minn., and Houghton, Mich. A dinner and meeting of the members in Pitts-burgh, Pa., was also attended, in company with the Secretary and your President also attended the meeting of Canadian Mining Institute in Montreal, in March, 1919.

Jan 2, 1920

By Sydney H. Ball

MINERALS used primarily for personal adornment and decorative purposes are called precious stones. To be so prized, the stones must possess beauty of color, must not be too common, and must be hard enough to withstand ordinary wear. If transparent, they must have brilliancy and fire. Almost one hundred minerals have been used as precious stones, the noble gems being the diamond, emerald, ruby, and sapphire; pearls are frequently included by courtesy. These gem stones, however, are sometimes equaled in beauty by fine opals, aquamarines, ourmalines, spinels, chrysoberyls (both cat's-eye and alexandrite), and spodumenes (hiddenite and kunzite). The Greeks, Romans, and medieval Europeans grouped together gem stones according to color and degree of transparency, and only as the niceties of mineralogy began to be known, about a century ago, was it realized how many different minerals have the beauty required of gem stones. Pliny, for example, did not distinguish between rubies and the red varieties of spinel and garnet, although he conjectured that the beryl and emerald were one mineral. GENERAL SURVEY Early man treasured bright colored berries, attractive shells, white teeth of wild animals and brightly colored pebbles, and used them as personal ornaments. In the eastern hemisphere, the earliest stones used were members of the quartz family (100,000 to 75,000 B.C.); then obsidian and amber (50,000 to 25,000 B.C.); the jade minerals, fluorspar and jet (22,000 to 7000 B.C.); turquoise (7000 to 3400 B.C.); lapis lazuli and garnet (prior to 3500 B.C.) ; emerald (2000 to 1800 B.C.) ; sapphire, ruby and diamond (800 to 500 B.C.). Indeed, gem mining is the oldest form of mining, and before any metals were known primitive man recognized about 18 gems and decorative stones. At first he sought them in stream gravels and residual deposits but by 3400 B.C. the turquoise mines of the Sinai Peninsula were operated. This was the world's first important hard-rock mining enterprise. The Afghanistan lapis lazuli mines may

Jan 1, 1949

By A. E. Jenkins, A. Jostsons

Isothermal sections of the Ti-0-H phase diagvam at 600°, 700°, and 800°C have been constructed from equilibrium hydrogen pressure measurements over a range of Ti-0-H alloys containing up to 34 at. pct 0. Oxygen reduces the hydrogen solubility at fixed hydrogen pressure but increases the terminal solubility in the a solid solutions at the a/(a + P) phase boundary. Metal-lographic studies of alloys annealed below the eutectoid temperature show that oxygen also increases the ter-ninal solubility of hydrogen in the a solid solution in equilibrium with the hydride phase. The effect of oxygen on hydrogen solubility is discussed in terms of the electronic and geometric structure of interstitial solid solutions. THE isothermal solubility of hydrogen in a Ti-0 alloys at 800°C has been measured by Hepworth and ~chuhmann' who subsequently used ternary Gibbs-Duhem integrations to calculate oxygen activities in binary Ti-0 alloys. The present study aims to extend Hepworth and Schuhmann's measurements to alloys richer in oxygen and to a range of temperatures. This paper presents the results of hydrogen equilibrium pressure/concentration measurements in Ti-0 alloys as well as observations on the effect of oxygen on the terminal solubility of hydrogen in a titanium. The thermodynamic properties of binary Ti-0 alloys, derived from these measurements, will be published separately.' EXPERIMENTAL METHODS Specimen Preparation. Ti-0 alloys were prepared from iodide-refined titanium and titanium dioxide obtained by hydrolysis of redistilled titanium tetrachlo- ride. Specimens containing up to 16 at. pct 0 were prepared by electromagnetic levitation3 whereas a conventional tungsten arc furnace with a water-cooled copper hearth was used to melt oxygen-rich alloys. The specimen homogeneity was indicated by the constancy of lattice parameters of samples from various parts of the ingot as well as by the sharpness of the reflections on X-ray powder patterns. Oxygen-rich specimens in the composition range (20 to 34 at. pct), where ordering has been ~bserved,~ were annealed for 300 hr at 600°C prior to use in hydrogen solubility measurements. Apparatus. The hydrogen pressure/concentration measurements were made with a modified Sieverts apparatus shown diagrammatically in Fig. 1. Specimens were placed in a clear silica tube and impurity pickup by direct reaction with silica was prevented by lining the heated end of the silica tube with thin molybdenum sheet. A double silica tube was required to eliminate loss of hydrogen by diffusion through silica at high temperatures and high hydrogen pressures, the space between the tubes being maintained at a hydrogen pressure equal to that above the specimen. Hydrogen was purified by diffusion through a Ag-Pd tube.= Hydrogen pressures were measured with a mercury McLeod gage in the range 0.001 to 4 Torr

Jan 1, 1968

By A. Adiassevich

PETROLEUM has been found in Russia in various localities from north to south, as may be seen from the list given below: (a) In the basin of the Petchora river, Northern Russia. (b) In the basin of the Volga river, in the governments of Samara and Saratoff. (c) In the government of Astrakhan and in the Uralsk territory, close to the northern and eastern coast of the Caspian sea. (d) At Grozny in Northeastern Caucasus. (e) In the Daghestan territory, Eastern Caucasus, on the Caspian sea. (f) On the Apsheron peninsula (Baku and other districts) close to the Caspian sea shore. (g) On the island of Tcheleken in the Caspian sea, also on the island of Sviatoi. (h) In the Transcaspian territory on the Neftianaia Gora (Oil hill) and on the surrounding hills. (i) In the Ferghana valley in Russian Central Asia. (j) On the Kertch and Taman peninsulas on the Black sea. (k) In Siberia it has been discovered in the Transbaikal territory and on the island of Sakhalin. In the above-mentioned districts petroleum has been found to exist under different geological conditions and to vary in its chemical and physical properties. At the present time petroleum is produced in Russia at Baku, Grozny, on the island of Tcheleken, in the Ferghana district, and in the Uralsk territory. The yearly production in 1912 throughout the Russian Empire amounted to 69,400,000 barrels, of which the Baku fields were responsible for 52,000,000 barrels. This shows that the Baku fields on the Apsheron peninsula are the chief oil-producing centers in Russia, being at the same time the oldest of all our oil fields.. In this paper I shall discuss the Baku fields only, leaving all the others until a later date.

Jan 5, 1914

By M. E. Wadsworth, A. E. Lewis, R. L. Braun

Experimental results obtained in laboratory leaching studies of primary copper sulfide ore in sulfuric acid systems pressurized with oxygen are interpreted by a computerized geometric model involving the movement of a reaction zone through the ore fragments. Physical properties of the ore, including size, shape, and mineral content, are considered. The leaching mechanism involves mixed kinetics and includes a surface reaction within a moving reaction zone plus pore diffusion of dissolved oxygen through the reacted portion of the ore fragment to the reaction zone. The results are applicable to conditions that would exist in nuclear solution mining or similar processes in which the ore is converted into rubble and then inundated by a leach solution adequately supplied with oxidants. Experimental results at 90°C are correlated with the model, which includes temperature-dependent parameters.

Jan 1, 1974

America.-Foreman, J. T. Ashland.-Sturdevant, J. C. AItalIa. Henderson, R. M. Bessemer.-Ball, E. M. Maschmeyer, W. L. McKenzie, W. C., Jr. Birmingham.-Abbott, C. E. Aldrich, T. H. Aldrich, T. H., Jr Aufderhaar, H. C. Berg, H. A. Blair, C. S. Bush, M. W. Clark, G. H.

Jan 1, 1923

By C. B. Sawyer

ALTHOUGH the element beryllium was discovered as the oxide by L. N. Vauquelin in 1797, this metallic element was not produced until about 1828, and then only as an impure powder. Thereafter the greatest single contributor to our early knowledge of beryllium was Lebeau who, in about 1899, made pure beryllium crystals by electrolysis of the fluoride and then beryllium copper by the arc-furnace reduction of beryllium oxide with carbon and copper. About twenty-five years later, under the impetus of the work done by Siemens-Halske, beryllium commenced to make relatively rapid gains in industrial importance, principally when alloyed with copper. At the present half century mark, its use is firmly established in beryllium copper and in X-ray disks of pure beryllium. Its use as a moderator in nuclear processes in piles is engaging experimental attention and might become important. Other minor uses, but increasing in interest, are in nickel-base or iron-base alloys as a strengthening agent; as a protective agent against oxidation in aluminum and magnesium-base alloys; and as a ceramic in the form of the pure fused oxide. A false start was made in the wide use of beryllium oxide as a fired fluorescent powder known as beryllium-zinc silicate, a component of the inside coating of fluorescent lamps. This application, wherein general use by the public attained some importance, was abandoned a few years ago. This action was a consequence of the uneasiness which had been generated during the past decade by the sometimes fatal health hazard to the pulmonary tract now generally attributed to beryllium and some of its compounds. Numerous law-

Jan 1, 1953

By Samuel L. Hoyt

The present report represents that part of the work that has been done by the War Minerals Investigation, Manganese Section, of the Bureau of Mines, on the use of manganese alloys in open-hearth practice. The magnitude of the work and the number of people participating in one way or another make it difficult to acknowledge adequately the services of all who have contributed to the success of the work. It would be amiss, however, to pass to the body of the report without mentioning the hearty cooperation and willingness to assist of the various manufacturing interests. With such a sympathetic attitude toward this investigation, our work was assured of success. Inasmuch as the unhappy circumstances that rendered this investigation necessary have now passed, this report is made in the hope that the results may prove of some permanent value to the peace-time operation of our open-hearth industry. Broadly speaking, the purpose of the manganese investigation was to consider the most suitable means of utilizing our domestic supply of manganese and thus relieve, to the maximum extent possible, our shipping of the burden of importing manganese ores. It was not held that any decided shortage of manganese was imminent but rather that every legitimate means should be utilized for making our ship tonnage available to European service. While we have considerable metallic manganese in this country, it occurs largely as a low-grade mixture with iron or silica or with both. The open-hearth investigations, therefore, were carried on to determine the extent to which domestic or low-grade alloys could properly be substituted for high-grade alloys without materially impairing the steel production as to either quality or quantity. Also, it was held that such an investigation would yield valuable results to the steel industry as well as contribute, in no small way, toward directing future investigations in the same field. To the practical steel manufacturer, especially to him who felt no immediate concern about

Jan 1, 1920

Homestake's Bulldog Mountain Operation near Creede, Colorado, in the San Juan Mountains at an elevation of nearly 2,750 m (9,000 ft), is subjected to short summers and long cold winters. Creede’s history dates back to 1889 when silver ore was discovered; and by 1892 production of over a million dollars per month was being shipped from mines located along the Amethyst Fault. The Bulldog Mountain Fault remained relatively untouched by the early prospectors. The United States Geological Survey recognized the potential of this fault in 1960, which led to the staking of many claims over the structure. Homestake leased properties in 1963 and in mid- 1964 a tunnel was started at the 2,956 m (9,700 ft) level with encouraging mineralization being encountered. In 1968 a decision was reached to build a flotation mill of 318 mtpd (350 stpd) capacity. The erection of the mill was completed in early 1969, six years after the first exploration was begun. Since initial start-up, extensive drifting has been done on several separate levels. Two underground hoist installations serve the various levels and many thousand feet of vertical mining operations. Due to the unconsolidated nature of the vein, a new unique underhand cut-and- fill mining method was developed. This procedure is the reverse of the normal cut-and-fill and proceeds from the top down under cemented sand fill, which, while expensive, has greatly reduced s toping hazards. Prior to 1977, a considerable quantity of silver was lost in the slime fraction of the ores processed because of oxidation and other inherent characteristics of individual minerals. Due to Homestakefs favorable experience in treating the slime fraction of the Lead, South Dakota gold ores, experiments with leach methods to recover silver from the slimes by Carbon -In -Pulp offered' the potential for additional silver recovery. Work was begun on the Carbon-In-Pulp plant in April 1976 and completed in December of that year at a cost slightly exceeding $2 million. The C. I. P. plant was designed for 136 mtpd (150 stpd) of current plant slimes plus 227 mtpd (250 stpd) of slimes dredged from the old tailings during the summer season. The sand fraction of the flotation

Jan 1, 1981

CONTENTS PAGE ZAPFFE, CARL.-Manganiferous Iron Ores of the Cuyuna District, Minnesota. Discussed by A. K. Knickerbocker 1 MCCORMACK, C. P.-Economics of the Cuyuna Manganiferous Iron Ores. Dis-cussed by T. L. Joseph, J. Wilbur Van Evera, C. P. Perin, T. T. Read, L. E. Ives 4 READ, T. T.-Probable Error in Blast-furnace Records and Calculations Therefrom. Discussed by C. H. Herty, Jr., T. T. Read, T. L. Joseph, Ralph H. Sweetser 8 SCHWARTZ, H. A. and HIRD, (Mrs.) ANNA NICHOLSON.-Chemical Equilibria During Solidification and Cooling of White Cast Iron. Discussed by N. B. Pilling, Ralph H. Sweetser, H. M. Boylston, Albert Sauveur 10 HERTY, C. H., JR., BELYEA, A. R., BURKHART, E. H., and MILLER, C. C.-Some Factors Affecting the Elimination of Sulfur in the Basic Open-hearth Process. Discussed by Henry D. Hibbard, L. F. Reinartz,. C. H. Herty, Jr., Ancel St. John, A. L. Feild, C. R. Hayward, Ralph H. Sweetser, C. D. King, Haakon Styri, George A. Orrok 12 HIBBARD, HENRY D.-Finishing Melting Temperatures of Simple Ingot Steels. Discussed by Haakon Styri, George V. Luerssen, A. G. Zimermann, A. L. Feild, George A. Orrok, Albert Sauveur, R. F. Harrington, Henry D. Hibbard, I. A. Billiar, William J. Priestley, H. W. Gillett, W. P. Barba, Jerome Strauss, Harry H. Smith, H. LeChatelier, L. F. Reinartz 19 HERTY, C. H., JR., and TRUE, O. S.-The Reaction between Manganese and Iron Sulfide. Discussed by A. L. Field, H. S. Rawdon, C. H. Herty, Jr., T. L. Joseph, Haakon Styri 37 KAMURA, HEIHACHi.-Reduction of Iron Ores by Carbon Monoxide. Discussed by T. L. Joseph, R. Franchot, Ralph H. Sweetser, C. H. Herty, Jr 43 JOSEPH, T. L.-Effect of Sulfur on Blast-furnace Process. Discussed by R. Franchot, C. A. Meissner, T. L. Joseph, C. H. Herty, Jr., Ralph H. Sweetser, I. E. Waechter, F. N. Speller, T. T. Read 45 GOOSTRAY, JOB, HARRINGTON, R. F., and HOSMER, M. A.-Brief History of Metallurgical Practice in Cannon-making with Particular Reference to the Cast-iron Gun. Discussed by A. G. Zimermann, Geo. A. Orrok, Chas. Me-Knight, Jr., F. Brauer 51 Manganiferous Iron Ores of the Cuyuna District, Minnesota Discussion of the paper of CARL ZAPFFE, presented at the New York Meeting, February, 1925, and issued, as Paper No. 1390-I, with MINING AND METALLURGY, December, 1924. A. K. KNICKERBOCKER,* Virginia, Minn. (written discussion).¬The author makes a broad distinction between the "black" ores (the

Jan 6, 1925

By D. Gupta, S. Weinig

This investigation comprises the study of dislocation-oxygen interactions in a! titanium and its effect on the ductile to brittle transition in titanium. Internal friction techniques using a low-frequency lorsion pendulum were used to study the oxygen atom interactions with dislocations in "superpurity" titanium. A calculation of the interaction energy between an oxygen atom and a dislocation, based on the "breakaway" strain resulted in a value of 0.015 ev as compared to theoretical values of 0.022 and 0.035 ev for edge and screw dislocations, respectively. Both the saturation of the room temperature decrement and the transition from ductile to brittle behavior occurred at 1.5 at. pct 0. It was proposed that the embrittlement was due to oxygen atoms immobilizing the dislocations. It was possible to increase the ductility of the Ti-0 binary alloys by decreasing the oxygen pinning. The increase in uniform elongation was 30 pct for an increase in the preanneal temperature of 300°C. ThE room-temperature ductility of a titanium is significantly affected by interstitial solutes. Although oxygen has a solid solubility of 15.5 pct by weight, the room-temperature ductility extends only to 0.6 pct.' The ductility precipitously falls at this concentration and the fracture characteristics change from ductile to brittle.2 The small effective bulk composition of solute required to destroy the room-temperature ductility of the titanium must be indicative of an in-homogeneous distribution of solute atoms. Internal friction techniques were used in this investigation to

Jan 1, 1960

By AIME AIME

The following changes of address of members have been received at the Secretary's office during the period of Mar. 1 to May 1, 1908. This list, together with the list in Bi-Monthly Bulletin, No. 20, March, 1908, therefore, supplements the annual list of members corrected to Jan. 1, 1908, and brings it up to the date of May 1, 1908. The names of Members who have accepted election during March and April, 1908 (new members), are printed in italics., By a simple method of cutting out these names and addresses, and pasting them directly over the corresponding names in the annual list of members, the record can be kept practically up to date and the value of the list correspondingly increased. For this purpose the changes of address have been printed only on one side of the page. The names of new members, being in italics, are readily distinguished from the others, and can be pasted in approximate alphabetical order on the margins of the pages of the list.

Jan 5, 1908

By Michael Tenebaum, C. C. Brown

In recent years, the importance of slag control in basic open-hearth operations has been universally recognized. To effect such control during the working period of the heat, methods have been developed to measure or estimate slag oxidation and slag basicity. While satisfactory rapid chemical methods have been developed to determine slag oxidation, no completely adequate method of evaluating basicity has yet been provided. The most generally accepted control methods of measuring slag basicity are based on visual cstimates. While considerable benefit may be derived from such estimates, the need for some measurable indication of slag basicity has become increasingly apparent. In a recent paper, Philbrook and Jolly suggested a promising technique for making the basicity determination. Their method consists of measuring the pH of a mixture of powdered open-hearth slag and distilled water. It was found that a relation could be established between the slag basicity and the alkalinity of the water mixture as measured by the hydrogen-ion concentration. The general procedure followed in making the measurements and the considerations involved in constructing the original curves are given in the paper of Philbrook and Jolly and need not be repeated. It is the purpose of this paper to discuss some of the factors considered in applying the pH measurements to actual slag control and to present some of the results of its apphcation. Factors Involved in Measuring pH of Water-slag Mixtures To facilitate the application of the pH control system, it was desirable that no alteration be made in the routine methods of sampling and crushing the furnace slag. Some of the factors considered before establishing a curve to relate slag basicity with the pH reading arc reviewed individually in the following paragraphs. Effect of Cooling Rate Under actual operating conditions there can be considerable variation in the temperature of the piece of slag crushed for the pH determination. To determine whether variations in crushing temperature or in cooling rate would affect the pH reading, a series of four samples was prepared from each of two separate slags. These samples represented conditions far more extreme than would actually be encountered. To obtain these samples, a thick pancake of slag was poured. One piece of this pancake was crushed immediately after it had solidified. Another piece was water-quenched and then crushed. A third piece was allowed to air-cool to room temperature before crushing. The fourth sample was prepared from a chilled slag. This sample was poured onto a heavy inclined steel plate at the

Jan 1, 1945

By D. E. Moore

The strength of a natural serpentinite gouge was measured at 400°C and an effective pressure of 100 MPa. The strength of the gouge decreased with increasing pore pressure to 50 MPa and then was nearly constant between 50 and 125 MPa. The samples at 50-125 MPa pore pressure slid stably, whereas those at 3-25 MPa pore pressure showed stick-slip behavior. Lengthening the pre-heating time to 72,000 s of samples at 100 MPa pore pressure led to increases in both the strength and the likelihood of sliding unstably. With still longer pre-heating times, the strengths decreased again and sliding once more became stable. The strength of the gouge at 3 MPa pore pressure was unaffected by changes in pre-heating time. A possible explanation for the results is that excess pore pressures are being generated in the gouge, causing the true effective pressure to be lower than the apparent value.

Jan 1, 1984

By Alfred E. Hunt

The late Alexander Holley said, on returning from a careful study of the relative merits of the Bessemer and the open-hearth processes, as shown in the best European practice, that, in this country, the open-hearth process would live to attend the funeral of the Bessemer ; and he said this several years ago, when in this country the Bessemer plant and practice had been developed to far outstrip that abroad, and when, proportionately, it had reached an advancement much beyond the improvements in open-hearth plants and practice. At the same time, the prevailing idea in the metallurgical world, a few years ago, seemed to be in favor of the substitution of Bessemer for open-hearth steel for most of the higher qualities, and Bessemer enthusiasts loudly proclaimed, that as good steel for all purposes could be obtained by their favorite process as by the open-hearth. It was, in fact, confidently prophesied that very soon tool-steel and similar grades, which consumers had learned to specify, in ordering, to be made by the crucible process, would by common consent be made by the Bessemer, as best adapted to give the desired results. But these expectations have failed to materialize; not only do the crucible people keep on in the even tenor of their way and talk with pride of their comparatively large outputs of " hundreds " of tons per month, as usual, but the open-hearth people have kept fast hold of their original domain of nearly the entire amount of sheared plates, of locomotive tires, of large forgings, spring-steel, agricultural steel, steel castings and the like. Further, owing largely to one of the great advantages of the Bessemer process, which is also one of its inherent dangers, namely, its large output, it has also fallen into considerable disrepute for structural purposes. Not a few experienced engineers are now stipulating in their specifications that Bessemer steel will not be allowed to be used, especially for tension-members.

Jan 1, 1888