Search Documents

By W. Philippoff, Donald E. Cadwell, S. R. B. Cooke

THE importance of contact angles in flotation has long been recognized, but little has been done to get quantitative relationships between the surface coverage of the mineral by the reagent, the length of the hydrocarbon chain, and the contact angle. It is well known that for a complete monolayer on the surface of a mineral the contact angle 8 is determined only by the reagent1 and principally by the chain length of the hydrocarbon radical. Although for flotation the monolayer usually is regarded as being complete, early experiments of Wark and Cox&apos; showed that at very small concentrations of potassium ethyl xanthate the contact angle on galena changed in a continuous way from 0&apos; to the equilibrium value of 60". Further, Gaudin and Vincenta showed a similar continuity using heptylic acid and sphalerite. This shows that with probably incomplete monolayers, 0 varies with the degree of surface coverage. At the time these experiments were made it was impossible to measure the actual amount of surface coverage, especially since the decrease of the collector concentration in the liquor could be influenced by chemical side reactions. Through the use of the radioactive tracer method for the measurement of the amount of collector adsorbed on the surface of the mineral, Gaudin and Bloecher&apos; were able to determine accurately the actual surface coverage of dodecylamine acetate on quartz, but they did not measure any contact angles. It is believed that the relationship between the surface coverage and the contact angle is extremely important in flotation, especially as Gaudin and Bloecher showed that a 95 pct recovery is possible with a coverage of only 5 pct. Theoretical Considerations The work of adhesion W is the energy bound (in ergs per sq cm) when an interface is formed. It is determined by the difference of the free surface energies (surface tensions) of the respective phases 7j and yZ before contact and the interfacial free surface energy y, after contact. The definition of the contact angle permits the elimination of the unknown surface energy of the solid and hence the calculation of W from the surface tension of the liquid y and the contact angle 8: W = y (1 + COS0) [1] Consider a surface consisting of two components, identified as 2 and 3, 1 being the liquid. The amount of 2 in the composite surface is x, where 0 < x < 1. The respective contact angles with 1 and air are 8, and 8.. The total work of adhesion of such a surface is the sum of the values of the components multiplied by their respective areas. A formal relation can be written: Wm = x-W2+ (l-x)-W, [2] in which W, is the work of adhesion of the composite surface. Eq 1 can be introduced into Wt and Wa, but in the case of W, some discussion is needed. If the two components are segregated, each component forming an integral part of the composite surface there is no physical meaning for a contact angle 8m calculated from W,, by using eq 1. If, on the other hand, the area of each patch of the components is small in comparison with, say, the diameter of the bubble used in measuring, it could be expected that 0m would have a physical significance, because of the action of the surface tension of the liquid-gas interface tending to smooth out sharp corners. How small these patches would have to be is difficult to predict, but by using composite surfaces with microscopically

Jan 1, 1953

By S. R. B. Cooke, W. Philippoff, Donald E. Cadwell

THE importance of contact angles in flotation has long been recognized, but little has been done to get quantitative relationships between the surface coverage of the mineral by the reagent, the length of the hydrocarbon chain, and the contact angle. It is well known that for a complete monolayer on the surface of a mineral the contact angle 8 is determined only by the reagent1 and principally by the chain length of the hydrocarbon radical. Although for flotation the monolayer usually is regarded as being complete, early experiments of Wark and Cox&apos; showed that at very small concentrations of potassium ethyl xanthate the contact angle on galena changed in a continuous way from 0&apos; to the equilibrium value of 60". Further, Gaudin and Vincenta showed a similar continuity using heptylic acid and sphalerite. This shows that with probably incomplete monolayers, 0 varies with the degree of surface coverage. At the time these experiments were made it was impossible to measure the actual amount of surface coverage, especially since the decrease of the collector concentration in the liquor could be influenced by chemical side reactions. Through the use of the radioactive tracer method for the measurement of the amount of collector adsorbed on the surface of the mineral, Gaudin and Bloecher&apos; were able to determine accurately the actual surface coverage of dodecylamine acetate on quartz, but they did not measure any contact angles. It is believed that the relationship between the surface coverage and the contact angle is extremely important in flotation, especially as Gaudin and Bloecher showed that a 95 pct recovery is possible with a coverage of only 5 pct. Theoretical Considerations The work of adhesion W is the energy bound (in ergs per sq cm) when an interface is formed. It is determined by the difference of the free surface energies (surface tensions) of the respective phases 7j and yZ before contact and the interfacial free surface energy y, after contact. The definition of the contact angle permits the elimination of the unknown surface energy of the solid and hence the calculation of W from the surface tension of the liquid y and the contact angle 8: W = y (1 + COS0) [1] Consider a surface consisting of two components, identified as 2 and 3, 1 being the liquid. The amount of 2 in the composite surface is x, where 0 < x < 1. The respective contact angles with 1 and air are 8, and 8.. The total work of adhesion of such a surface is the sum of the values of the components multiplied by their respective areas. A formal relation can be written: Wm = x-W2+ (l-x)-W, [2] in which W, is the work of adhesion of the composite surface. Eq 1 can be introduced into Wt and Wa, but in the case of W, some discussion is needed. If the two components are segregated, each component forming an integral part of the composite surface there is no physical meaning for a contact angle 8m calculated from W,, by using eq 1. If, on the other hand, the area of each patch of the components is small in comparison with, say, the diameter of the bubble used in measuring, it could be expected that 0m would have a physical significance, because of the action of the surface tension of the liquid-gas interface tending to smooth out sharp corners. How small these patches would have to be is difficult to predict, but by using composite surfaces with microscopically

Jan 1, 1953

By T. M. Gurr

The United States is the world&apos;s leading producer of phosphate rock. In 1975 according to the US Bureau of Mines&apos; statistics, 44.3 million tonnes (48.8 million st) of phosphate rock were produced in the United States, 1 which is 40.6% of the world&apos;s production.2 The major phosphate producing areas of the United States are located in Fig. 1 and the production for 1975 is listed as follows:

Jan 6, 1979

SAMUEL L. HOYT,* Minneapolis, Minn. -I was privileged to see the apparatus used by Mr. Scott, which is quite unique. It is, as the author says, a modification of the apparatus designed by Dr. Rosenhain, but it is evidently quite an; improvement. The author is to be congratulated on the fact that lie has given us, with his apparatus, a quantitative thermal analysis of these critical points. I notice the author refers to Ac3, Ac2, and Ac1. His designation of the Ac2 point is all right, but naturally in a steel with as much carbon as this, which would mean a hypereutectic steel, the other point might better be considered as an Ac, point with possibly another point above the Ac, point. Another important point brought out is the fact that, in Fig. 3, the lines representing the Ar1, transformation and the Ac,1_3 transformation do not intersect at the zero rate curve,

Jan 5, 1919

By T. P. Meloy

Recently, Gilvarry1 has criticized the Gaudin-Meloy2 derivation of the size distribution equation for impact grinding. The criticism states that as the derivation stands it is good for only a long, thin wire being fractured. This paper contains a second derivation in reply to the criticism. Consider a homogeneous solid particle. This particle is broken into fragments by impact. It is assumed that the material resembles galena and that the particles were broken into chunky parallelepipedes which may be treated as cubes. The fragments are now reassembled — as seen in Fig. 1 — and a line is passed through the fractured solid perpendicular to one of its faces. For simplicity, the length of the line segment in the cube is considered to be 1. Fig. 2 represents the line segment in the cube showing the locations of the crack surfaces cutting the line and one point, P, chosen at random on it. The question arises as to what is the probability of the point, P,

Jan 1, 1963

By Fred C. Bond and

This paper is a continuation of two earlier papers,12 and presents new data on the grindability of various ores and other materials—the results of several years of intermittent research work on the nature of grinding and interpretation of test results. It is divided into five parts: 1. The tabulated results of several hundred grindability tests on a wide variety of ores. 2. A method of correcting screen analyses and calculating from them the surface and other properties. 3. A description of a new method of measuring the "surface energy" of an ore by pendulum impact tests. 4. Test results. 5. A general discussion of the test results and their application to grinding problems. 1. GRindability of Various Ores This part is a continuation of the paper listed as reference No. 1. The method of testing is described in detail in that paper. The sample to be tested is crushed to all through 6 mesh in rolls set at 1/16-in. opening in closed circuit with a screen. Of this sample 700 C.C. is ground dry in a laboratory ball mill under constant conditions of mill speed and ball charge in closed circuit with a screen of the desired size at 250 per cent circulating load. The mill is cylindrical, 12 by 12 in., and rotates at 70 r.p.m. It contains a charge of 285 iron balls weighing 20,125 grams and ranging from 1½ to ¾ in. in diameter. Each test is continued for a sufficient number of periods to establish equilibrium at 250 per cent circulating load, or until the composition of the circulating load is constant for successive periods. Tests are conducted at the mesh size to which the ore is to be ground in practice, and the results are expressed as the net production in grams of screen undersize per revolution of the mill. This is designated as the

Jan 1, 1939

By Fred C. Bond and

This paper is a continuation of two earlier papers,12 and presents new data on the grindability of various ores and other materials—the results of several years of intermittent research work on the nature of grinding and interpretation of test results. It is divided into five parts: 1. The tabulated results of several hundred grindability tests on a wide variety of ores. 2. A method of correcting screen analyses and calculating from them the surface and other properties. 3. A description of a new method of measuring the "surface energy" of an ore by pendulum impact tests. 4. Test results. 5. A general discussion of the test results and their application to grinding problems. 1. GRindability of Various Ores This part is a continuation of the paper listed as reference No. 1. The method of testing is described in detail in that paper. The sample to be tested is crushed to all through 6 mesh in rolls set at 1/16-in. opening in closed circuit with a screen. Of this sample 700 C.C. is ground dry in a laboratory ball mill under constant conditions of mill speed and ball charge in closed circuit with a screen of the desired size at 250 per cent circulating load. The mill is cylindrical, 12 by 12 in., and rotates at 70 r.p.m. It contains a charge of 285 iron balls weighing 20,125 grams and ranging from 1½ to ¾ in. in diameter. Each test is continued for a sufficient number of periods to establish equilibrium at 250 per cent circulating load, or until the composition of the circulating load is constant for successive periods. Tests are conducted at the mesh size to which the ore is to be ground in practice, and the results are expressed as the net production in grams of screen undersize per revolution of the mill. This is designated as the

Jan 1, 1939

By Samuel Hoyt

This paper gives a short account of plastic deformation as observed in single crystals of zinc, zinc having been selected for the experiments described herein because the phenomena are comparatively so simple and can be studied throughout such a wide range. It is hoped that the paper will serve to show the type of information which studies of single crystals afford and will contribute toward the solution of the general problem of metallic behavior. PRODUCTION OF ZINC SINGLE CRYSTALS The method of Czochralski,1 as modified by vow Gomperz,l was used to produce the crystals studied. The equipment is shown in Fig. 1. Molten zinc is held in a crucible at a temperature which is not far above its melting point, as measured by a pyrometer. A lava disc floats on the melt, and is provided with a central hole about 1 min. in diameter. A glass tube, drawn into a capillary at the lower end, is suspended from a string which is wound up by an electric drive at the speed desired. At the start, the glass capillary is let down into the melt and the hoist is started. The capillary brings up a small quantity of molten metal with it to a point just above the lava disc. At this point, a jet of hydrogen cools it and causes it to crystallize, with the result that a -small crystal forms. As the hoisting is continued, more molten metal is drawn up, in turn to be solidified by the jet of hydrogen. This additional metal continues the growth of the crystal already formed, and a long, cylindrical crystal results. The speed of hoisting used was generally between 0.1 and 0.5 mm. per sec., and the crystals were from 4 to 6 in. long and about 1 mm. in diameter. By varying the conditions, crystals of quite different orientations were obtained and were used in the study of the phenomena to be described.

Jan 1, 1927

By R. D. Groves, G. M. Potter, T. H. Jeffers

Experiments on ammonium carbonate leaching of native copper ores crushed to 1-inch size showed that in 30 days 55 percent of the copper was extracted from 0.7 percent copper conglomerate-type ore, and 85 percent was extracted from 2.1 percent copper amygdaloid-type ore. Cupric ions were not necessary to initiate leaching, and dilute solution containing only 2.2 grams per liter NH3 and 1.9 grams CO, was a suitable solvent. Copper was recovered from the leach liquor by solvent extraction and electrolysis of the strip solution. Cyclic testing of the leach-solvent extraction-electrolytic procedure is in progress on a 6-ton charge of minus 12-inch conglomerate-type ore assaying 2.2 percent copper. Oxygen is metered to the closed leach vessel as required by the leaching reaction. Initial copper dissolution was much slower than from minus 1-inch ore, but the leaching rate then markedly improved.

Jan 1, 1974

By Frank Firmstone

Discussion of the paper of John B. Dilworth, presented at the Pittsburg meeting, March, 1910, and printed in Bulletin No. 35, November, 1909, pp. 1041 to 1043. FRANK FIRMSTONE, Easton, Pa. (communication to the Secretary*) :-Mr. Dilworth&apos;s formulas and tables are of course correct, and the extinction will occur as calculated, provided the money periodically set aside for sinking-fund be really invested. and the interest compounded as assumed in the calculation. Actually, in almost all cases, such funds are used "in the business," in which case, in addition to the periodical charges for principal of the fund, additional charges must be made at the end of each period to cover the interest and compound interest on previous charges. The periodical charge for sinking-fund thus becomes a varying and continually increasing one until the date of extinction. On many accounts it seems more natural and convenient to make the extinction by a fixed periodical charge under the legal rule for partial payments, namely, that each payment should apply first to the interest due at the date of payment;: and any remainder, after this is satisfied, be deducted from the principal before the interest for the next period is calculated. The formula below is convenient for such calculations S, Principal to be extinguished. Q, Periodical payment or charge for sinking-fund. B, Balance unpaid at date of nth payment, but before that payment is made. r, Rate of interest per period per cent. n, Number of payments or periods. Then, B=S(1+r)n-Q(1+ r)n-(1+r) Received July 27, 1910.

Apr 1, 1911

By Glenn C. Waterman

Richard Strong (Oliver Iron Mining Div., U. S. Steel Corp.)—Mr. Waterman states (p. 59, Trans., January 1954): "Core-sludge combining factors have been calculaied for any combination of core-sludge recovery on the basis of several logical assumptions: 1—The sludge sample loses reliability geometrically as sludge recovery drops. 2—The sludge sample should not be used if the percentage of sludge return is less than the percentage of core recovered. 3—A core sample should receive a weighting at least equal to the percentage of core recovery." Assumptions 1 and 2 seem justified at Chuquicamata and most geologists would agree to the validity of assumption 3. However, contrary to the statement quoted above, the core sample does not in general receive a weighting at least equal to the percentage of core recovery when the Chuquicamata methgd is used. Furthermore, the basic Chuquicamata method is identical to the Longyear or relative volume core-sludge assay combining method. Finally, the Chuquicamata method does not, in its present form, reflect true geometric loss in sludge sample reliability according to the relationship L = AR (N-1) The basic equations representing the two steps of the Chuquicamata method can be combined algebraically as follows (using the symbology of the original article except as noted): Vol A + B Assay 2 = ASA = Assay 1 Vol A VolB Core Assay [I] Vol A CA.F + ASA (100 —F) Combined grade =[21 100 Pct where F and (100 — F) are the core and adjusted sludge assay factors from Fig. 3. Substituting Eqs. 1 and 2 and collecting terms Combined grade = Vol B Vol A + B CAF (100—-F) + Assay 1 (100-F) Vol A Vol A 100 pct Eq. 3 is a unified and general statement of the Chuquicamata method. The true core factor includes not only the factor F from Fig. 3 but also the quantity VolB ------------- (100 — F), which is implicit in the value of Vol A the adjusted sludge assay. This quantity is real and positive for all values of F and core recovery less than 100. Therefore the true core factor is always less than F except when F is equal to 100. If sludge recovery is 100 pct, Eq. 3 can be further simplified as follows: Let F = percentage of core recovered. Let Vol A = Vdh (100 Pct — Pct CR) where Vdh is the total volume of the sampled interval and let Vol B = (Vdh — Vc.) Pct CR where V, is the core volume in the sampled interval at 100 pct core recovery. Then combined grade = Vo V. CA Pct CR- + Assay 1, 100 Pct — Pct CR Vdh Vdh [4] 100 Pct Eq. 4 shows that when sludge recovery is 100 pct the laboratory sludge assay receives significant weight in the Chuquicamata method, even at 100 pct core recovery. The maximum weight assigned to the laboratory sludge assay depends on drillhole size, as follows: Eq. 4, with suitable changes in symbology, is identical to Royce&apos;s formula 8,&apos; which is a statement of the Longyear or relative volume method of combining core and sludge assays. If Mr. Waterman&apos;s assumption 3 is of paramount concern to the geologist, the Royce method (for core recoveries of 60 pct and above) or a method employing the percentage of core recovered as a core weighting factor are the only recognized methods known to the writer which achieve the desired result. A modification of the latter method embodying Mr. Waterman&apos;s assumptions 1 and 2 would result from applying the factors from Fig. 3 directly to the laboratory core and sludge assays.

Jan 1, 1956

By Lawrence Adler

MINE hoist ropes have hitherto been selected by successive approximation, a process both tedious and inexact. The proposed expression is a readily solved synthesis of existing data and the following standard equation:&apos; [ W + Wr + (W + Wr) -a 9 (W + W)f + b] n=T [1] For convenience, a glossary of all terms appears on page 564. Since rope weight (W,) and bending load (B) are functions of unit rope weight (Wv), which in turn is a function of rope strength (T), W, and B can be expressed in terms of T. W, as a Function of T: A study of the curve in Fig. 1, unit rope weight vs strength, yields Eq. 2: W. = -f- [2] Therefore Wr = WvL = T. [3] iv B as a Function of T: From Fig. 2, unit rope weight vs diameter, Eq. 4 is obtained: W, = 1.6d2 [4] B is related2 to d and D, and d has been expressed in terms of W, by Eq. 4, so the curve B vs W, (Fig. 3) gives Eq. 5: 177,000 177,000 This may readily be checked from the expression3 for a 6x19 rope, i.e., d3 B = 288,000D Since d2 = 0.625 W, and N = substituting d into the above expression gives Ea. 6: 180,000 180,000 B T, which will be used. [6] Into Eq. 1 substitute Eq. 3 and Eq. 6, noting that f=0.02: W + T 1.02+=T. [7]

Jan 1, 1958

By Y. L. Yao

THE NaT1-type compound may be considered as the penetration of two diamond lattices in such a way that a superstructure of the bcc lattice is formed. Examples of the NaT1-type compound of lithium are LiZn, LiCd, LiA1, LiIn, and LiGa. Except for LiZn and LiCd, each molecule of these equiatomic compounds contains a total of four valence electrons. In LiZn and LiCd it was suspected (for example, see Ref. 1) that the fourth electron was withdrawn from the 18-shell of zinc or cadmium. An incomplete 18-shell would have to show strong paramagnetism. In 1955 Klemm and Fricke2 determined the magnetic susceptibility of LiZn, LiCd, LiA1, and LiIn (also NaTl and NaIn). The molar susceptibility of the outer electrons of LiZn and LiCd was found to be not strongly but weakly positive; that of LiAl and LiIn not negative but weakly positive. Thus they questioned the hypothesis about LiZn and LiCd in particular and the description of the NaT1-type structure in general. However, they did not determine the magnetic susceptibility of LiGa. This note is to report results for all five compounds of lithium. The starting materials are 99.9 pct pure lithium sticks containing less than 0.005 pct Na. 99.9 pct Zn, 99.9 pct Cd, 99.99 pct Al, 99.999 pct In, and 99.999 pct Ga. Weighed amounts of two components were wrapped in tantalum foil and placed in a graphite crucible. It was found that the tantalum sheath minimized the vaporization losses of lithium during melting. The sheath was easily stripped from the alloy rod and the tantalum in the alloy was barely detectable (less than 0.01 wt pct). The melting was performed in a resistance furnace under an argon atmosphere. Alloy specimens were annealed for 1 hr at 400°C in vacuum. The magnetic susceptibility at room temperature was determined by the Faraday Method, using the procedures previously described.&apos; The results are shown in Table I. The interpolated values at 50 at. pct of Li and the average values at 48 to 52 at. pct of Li at 20°C determined by Klemm and Fricke2 are also shown. It is seen that the present value for LiZn and LiCd is slightly more positive but the present value for LiAl and LiIn is slightly less positive than their corresponding values. Also, it is noted there is an abrupt decrease of susceptibility of LiAl from 51.2 to 52.5 at. pct of Li. Klemm and Fricke2 found that the total susceptibility of LiZn, LiCd, LiA1, and LiIn is almost independent of temperature. slater4 gave a working expression for the diamagnetism of the atomic core as follows:

Jan 1, 1964

By W. Denham Verschoyle

IN designing a pocket instrument whereby any given horizontal or vertical angle may be closely approximated, the following points should be kept in view, if general utility is aimed at 1. The instrument should be light and compact, so that it can be carried in the pocket, or in a sling. 2. It should be capable of observing any angle whatever, horizontal or vertical. 3. Since time is often an important consideration in making a preliminary survey, it should be capable of giving the horizontal and vertical angle at one observation. I do not know of any instrument that will fulfill these requirements, except the one here described. Where the depression- or elevation-angle of the distant object, whose bearing is required, exceeds 50 or 60 degrees, it becomes difficult or impossible with a prismatic compass, for instance, to obtain accurate results; and since it frequently happens, particularly in mining, that much work requires to be done beyond that limit, it is obvious that an instrument which can be used to observe a high angle just as easily as a low one, if not absolutely a necessity, will at least be a great convenience. How this " pocket transit " attains to the required degree of universality will be understood from the diagram, Fig. 1, in which B is a beveled, graduated circle, attached to and freely revolving about the center of the magnet A. Light falling on B is reflected through a window in F (the compass-box), along the line AC, and is again reflected back to the eye at D by the prism C. By a simple arrangement, the sight-line DCE can be completely revolved in the vertical plane DE, which is normal to AC. It is clear, then, that no matter through what vertical

Jul 1, 1907

By Charles E. Lundin, Albert S. Yamamoto

The phase eqrtilibria of the binavy system, Nb-Al, weye established by metallographic, X-ray diffraction, hardness, and thermal-analysis techniques. Three intermediate phases were identijied, Nb3.41, Nb2Al, and NbAl,. The N6,Al and NbAl phases have extensiue ranges of solubility. The maximum solubility of aluminum in niobiuitz is 23.0 i0.5 at. pct (8.0 wt pct) A1 clt 1960" i 10°C. The maximumt solinbility oj niobiunz in alunzinutz is less than 0.3 i0.1 at. pct (1.0 tut pct) fib. The A&apos;h,Al and Nbgl interinediate phases forr peritectically at 1960° 1UcC and 1870" i 1U9C, respectively, zuhereas the NbAl, phase fornts congvuently fio11t the melt at 1605" 10°C. A eutectic reaction oc- The intent of an over-all research program was to develop niobium-aluminide-base coatings for refractory metals since these coatings exhibit useful high- curs at 57.8 i 0.5 at. pct (28.5 wt pet) A1 and 1500" 10°C between NbAl and NbAl3. The aluminum-rich region of the system has a peritectic reaction where liquid reacts with NbAL, to form aluminum solid solution. Structural and lattice -pavarneter data /or the intermediate phases were determined by X-ray diffraction analyses. An unusual transfov?nation having charactevistics of nucleation-growth and martensitic nleclanisils occurs on cooling the niobium solid solution in the region from 18 at. pct (6 wt pct) Al to 23 at. pct (8 wt pct) Al. The transfornzed product on rapid quenchirzg is an acicular NhAl. temperature resistance to oxidation. As a prerequisite, the phase equilibria of the system, Nb-A1, were necessary. A literature survey revealed that the phase-equilibria data reported by various investigators were rather incomplete and conflicting. Therefore a complete determination of the system was undertaken by the authors from 0 to 100 pct of solute addition.&apos; In 1959 Savitskiyz presented a tentative diagram which

Jan 1, 1967

By Clarence Linville

FULTON1 says: "Speiss is an artificial arsenide of iron containing smaller amounts of other metals. In constitution it is similar to a matte except that arsenic replaces sulfur." For the purposes of this paper it will be necessary to broaden the definition, and I propose the following: Speiss is an artificial mixture of arsenides, of which arsenide of iron may be taken as a type, but iron may be replaced in part or wholly by other metals (such as copper, nickel, cobalt, lead and zinc) and the arsenic may be replaced in part or wholly by antimony. In addition to antimony and arsenic, speisses often contain sulfur. Speisses usually also contain both silver and gold. Table 1 illustrates the variations that may be encountered. TABLE 1.-Speiss Analyses

Jan 5, 1925

By C. A. Rowland, R. C. Nealey

Wet grinding rod mills have been used for 50 years to grind ores and to make specification sand. The application of wet grinding rod mills is well understood. Until recently, there have been very few installations of dry grinding rod mills. The selection of dry grinding rod mills follows the basic principles established for the selection of wet grinding rod mills. The basic Bond Formulae1 [ ] is used to select mills when using grindability test results as the basis for selection. W is multi- plied by the 1.3 wet to dry grinding factor established from wet and dry ball milling experience, and then by any other applicable inefficiency factors.1 Dry grinding rod mills have also been selected by scaling up bench scale continuous rod mill tests and pilot plant tests.

Jan 12, 1968

By B. Ramaswami

INTERNAL oxidation occurs readily in silver due to the rapid diffusion of oxygen in silver.&apos; It has a marked effect on creep in polycrystalline silver2 and raises the critical resolved shear stress in single crystals of silver.3 However, the effect of oxygen on the work-hardening parameters of silver is not known. It is the aim of this paper to describe the effect of internal oxidation on the work-hardening characteristics of single crystals of silver and an Ag-0.1 at. pct A1 alloy. The materials used were: 99.99 pct Ag from Handy and Harman and 99.993+ pct A1 from Alcoa. Single crystals, 6 mm by 6 mm in cross section of silver and Ag-0.1 at. pct A1 of mo.5 orientation, i.e., the orientation with the Schmidt factor m = 0.5. were grown by the Chalmers technique.4 One set of specimens, referred to herein as oxidized specimens, was annealed at 940°C for 24 hr in a muffle furnace, in air, and furnace-cooled to room temperature. Another set of specimens, referred to as nonoxidized specimens, was annealed in oxygen-free helium at 940°C for 24 hr and furnace-cooled over a period of 7 hr to room temperature. The annealed single crystals were tested at room temperature in a floor-model Instron testing machine. The results are presented in Figs. 1 and 2. A

Jan 1, 1965

By W. Rostoker, S. Spachner

A N alloy of 50 pct Ni-50 pct Fe is currently manu- factured in tape thickness down to 1/8 mil. In the annealed form, this alloy produces an almost square hysteresis loop. This has generally been related to the fact that by proper rolling and annealing practice a sharp cube, (100) [OOl], texture can be developed. As part of a program directed toward an understanding of the relationships between magnetic properties and structure of tape core materials, analyses were made of preferred orientations in tapes of various thicknesses. Annealed tapes of this alloy in 2, 1, 1/2, ¼, and Y&apos; mil gages were acquired from commercial sources. Pole figures constructed for the 2 and 1 mil tapes showed the expected sharp cube texture. However, the ½, ¼, and ? mil annealed tapes showed no evidence of any preferred orientations. A comparison of two transmission patterns is shown in Fig. 1. The origin of the absence of texture in the tapes of less than 1 mil thickness was explored in some detail. The basic questions were whether the heat treatment for the thinner tapes was wrongly selected, whether the initial cold worked textures were different, or whether the actual thickness of the tape exercised some influence on its annealing characteristics. Quantities of the five gages of tape were acquired in the as-rolled condition just prior to the final anneal. Pole figures of the cold worked textures were constructed for each of the tapes. Eye estimates of in-

Jan 1, 1956

By K. R. Evans

The yield and fracture characteristics of a Ti-8 pct A1 alloy have been examined at room temperature as a function of exposure temperatures to 1700°F. Em-brittlenzent of the alloy is observed to occur following exposures below 1280°F, the critical temperature for formation of ordered Ti3Al particles. Presence of Ti3Al particles results in an increase in the yield and flout stresses which, for a given exposure time, are a maximum at the critical temperature. Embrittlement is attributed to the occurrence of plastically induced fracture controlled by the increase inflow stress. This interpretation is compatible with the decreasing ductility and increasing crack popagation rates observed with increasing exposure time below the critical temperature. Slip line observations and measurements of the gain size dependence of the yield stress indicate that the slip character of the alloy is not influenced by exposure treatments below the critical temperature. ThE potential usefulness of Ti-A1 alloys in structural applications has prompted considerable interest in studies of their microstructure and mechanical characteristics. The relatively recent surge of interest in the system and at the same time its complexities are indicated by the fact that despite numerous recent efforts14 there has not even been general agreement upon a phase diagram for the system. However, most of the Ti-A1 alloys of commercial interest range in aluminum content from 5.0 to 8.5 wt pct where most investigators achowledge the existence of the ordered Ti41 phase. Goldak and parrs confirmed the existence of Ti41 from X-ray diffraction analysis of the stoichiometric composition while Blackburn6 has determined its presence in commercial Ti-8 pct A1 alloys by electron diffraction analysis and dark field transmission microscopy. The embrittlement of Ti-8 pct A1 alloys was initially reported by Crossley and carew7 who showed that aging in the temperature range of 750" to 1110°F resulted in extreme brittleness. This behavior was later confirmed and correlated by Soltiss to the presence of long-range order in the commercial Ti-8 pct Al-1 pct Mo-1 pct V alloy (Ti-8-1-1) which exhibited anomalous creep and yield strength behavior at 950°F. This investigation was designed to study the mechanical characteristics of a binary Ti-8 pct A1 alloy in order to further examine the nature of the embrittlement behavior reported for the alloy system. EXPERIMENTAL PROCEDURE A Ti-8 pct A1 binary alloy was obtained from the Wah Chang Co. in the form of 0.050 in. sheet. The chemical composition of the alloy is given in Table I. Heat-treatment of the alloy was conducted in evacuated vycor capsules for the tensile sDecimens (1.25 bv 0.25 in. gage section) and in evacuated stainless steel jackets for the crack growth-rate panels. All specimens were annealed at 1700°F for 24 hr and water quenched before an exposure at elevated temperatures. Tensile testing was conducted at room temperature in an Instron testing machine equipped with a pushbutton control for instantaneous control of the cross-head motion. In this manner the change in stress, Aa, accompanying an increase in strain-rate by a factor of 10 was measured immediately after yielding. The crack growth-rate panels used were 3 by 18 in. with a precrack 0.33 in. long cut into the center of the panel. The panels were cycled at a maximum gross stress of 40,000 psi at a maximum to minimum tension stress ratio of 20. Cycling of the specimens was continued until the crack propagated the width of the panels. The crack length was intermittently measured during slow crack growth. EXPERIMENTAL RESULTS Correlation of Embrittlement to the Critical Temperature for Ordering. Blackburn6 has found that the critical temperature, T,, for the formation of Ti41 in a Ti-8 pct A1 alloy with an interstitial content on the order of that given in Table I is approximately 1245°F. The relationship between the ductility of the binary alloy used in this investigation and T, was estimated from tensile tests on specimens which were exposed for 24 hr at various temperatures followed

Jan 1, 1970