Search Documents

By H. R. Cooper, T. S. Mika

T. S. Mika (Department of Mineral Technology, University of California, Berkeley, Calif.) - Dr. Cooper's attempt to establish a correlation between process behavior and operational variables on the basis of a statistical analysis after imposing a reasonable process model is a very commendable improvement on the use of standard regression techniques. However, it must be recognized that the imposition of a model has the potential of yielding a poorer representation if its basic assumptions or mathematical formulation are invalid. It appears that at least two aspects of his treatment require some comment. First, the limitations on the kinetic law where xta represents a hypothetical terminal floatable solids concentration (cf. Bushell1), should be mentioned. Most current investigations2-9 appear to utilize the concept of a distribution of rate constants rather than a single unique value, k, to describe flotation kinetics. A distributed rate constant is certainly a more physically meaningful concept than that of a terminal concentration. The study of Jowett and safvi10 strongly indicates that xta is merely an empirical parameter, whose actual behavior does not correspond to that expected from a true terminal concentration. Rather than being a strictly mineralogical variable, as Dr. Cooper's treatment implies, it apparently represents the hydromechanical nature of the test cell as well as the flotation chemistry. The extension of batch cell kinetic results to full-scale continuous cell operation is a suspect procedure if the effect of such nonmineralogical influences on x,, remain unevaluated. There is evidence that introduction of a terminal concentration is necessitated by the inherent errors which arise in batch testing and are eliminated by continuous testing methods.' Possible lack of validity of the author's use of Eq. 1 is indicated by two unexpected results of the statistical analysis of his batch data. The first is the apparent corroboration of the assumption that the rate constant, k, is independent of particle size, i.e., of changes in the size distribution of floatable material. This assumption directly contradicts numerous results 2,4,11-l8 for cases where first order kinetics prevailed and ignores the phenomenological basis for the analysis of flotation in terms of a distribution of k's. It must be recognized that, if the rate constant is size dependent, the lumped over-all k would be time dependent; Eq. 1 would then no longer be valid. Cooper's x,, is determined by batch flotation of a distribution of sizes for an arbitrary period of time. If the size dependence of k is artificially suppressed, x,, will become a function of the experimental flotation time used in its determination. Upon reviewing the rather extensive literature concerning batch flotation kinetics, there appear to be few instances where constant k and x,, adequately adsorb variations in floatability due to particle size. The second surprising result is the low values of the distribution modulus, n, determined. Contrary to Cooper's assertion, most batch grinding (ball or rod mill) products yield values of n > 0.6, which increase as the material becomes harder.'' It is likely that the values of n = 0.25 and n = 0.42 for Trials 1 and 2, respectively, are completely unreasonable, and even the value n = 0.54 obtained for Trial 3 is unexpectedly low. Possibly, this indicates inherent flaws in the three trial models considered, in particular the assumed particle size independence of the rate constant, k. The above does not necessitate that Eq. 1 (and the terminal concentration concept) is invalid; it could constitute a good first approximation. However, the qualitative arguments used by Dr. Cooper in its justification are somewhat frail and require verification, particularly since much of the flotation kinetics literature is in opposition. Apparently, no effort was made to test these hypotheses on the actual data; in fact, since they pertain to a single batch test time, his data cannot be utilized to evaluate the kinetics of flotation. To evolve a control algorithm on the basis of this infirm foundation seems a questionable procedure. Another difficulty in his analysis arises in consideration of the froth concentrating process. As Bushel1 ' notes, for Eq. 1 to be valid it is necessary that the rate of recycle from the froth be directly proportional (independent of particle size) to the rate of flotation transport from the pulp to the froth, a restrictive condition." Harris suggests that it is more realistic to assume that depletion occurs in proportion to the amount of floatable material in the pertinent froth phase volume (treating that volume as perfectly mixed).12,21,22 The physical implications of

Jan 1, 1968

TO metallurgists generally, Arthur S. Dwight is no stranger even to those who do not know him personally. He is one of those contributors to technical progress whose names will go down to posterity because of their being attached to a successful machine or process, such as Dorr, Hardinge, or Marcy, or Wedge, MacDougall, or Herreshoff. The roasting and sintering method and equipment developed by Colonel Dwight and his associate, the late Richard L. Lloyd, may be found in lead smelters throughout the world, and also in many metallurgical works dealing with other ores, including those of iron. It is ordinarily used to desulphurize and agglomerate fine ores for subsequent smelting. Colonel Dwight's citation as James Douglas Medalist reads: "For his contributions to the art of smelting nonferrous ores; and particularly for his pioneer work in developing equipment and technique for sintering such ores and metallurgical products." The medal was awarded at the last Annual Meeting of the A.I.M.E. but unfortunately the medalist was unable to leave Florida at the time to receive it in person.

Jan 1, 1942

By R. Bakish, C. S. Barnett

IN experiments on tantalum strained in tension, Bechtold did not observe deformation-twinning even at a temperature as low as that of liquid air.' This is an unexpected behavior for a metal of body-centered-cubic structure. Therefore, it is desirable to determine whether the lack of twinning is an inherent characteristic of this particular metal, or whether the reluctance to twin can be overcome under suitable conditions. The following experiments were performed under conditions favorable to twinning and cleavage in their competition with slip, namely, with impact loading on large-grained sheet at low temperatures. The crystallography of cleavage in tantalum sheet was also investigated carefully because of the remarkable ductility of tantalum at low temperatures and because recent tests on oxygen-embrittled tantalum had disclosed unusual cleavage behavior for a metal of this structure: cleavage primarily on (110) planes and only occasionally on {100}.2 The tantalum, supplied by Fansteel, was of 99.9 pet purity, with the chief impurities being iron (0.03 pet) and carbon (0.03 pet). Coarse grains were produced by the strain-anneal method, the anneal being 4 hr at 2000°C in a vacuum of 10-3 mm Hg, followed by furnace cooling. Impact deformation was applied in various ways: a) by hammer blows on an anvil, the specimen and anvil being immersed in liquid nitrogen ( —196°C), b) by driving a precooled center-punch into the sheet, and c) by bending around a crystallographically determined axis with a hammer blow. The impact-deformation produced bands and slip lines on the surface, Fig. 1. The bands have every appearance of being deformation twins, a) They are tilted with respect to the untwinned surface. b) They have the appearance of Neumann bands in iron, thin lens shape, some having serrated edges. c) The orientation in each is different from that of the surrounding matrix and uniform within a given band, see slip lines within them in Fig. 1. d) Upon repolishing and etching, the difference in orientation and the resemblance to Neumann bands is again evident, Fig. 2. (In this micrograph the slight bend in the bands as they cross grain boundaries was noted frequently and results from the high degree of preferred orientation in the sheet.) e) The bands persist after annealing treatments that would have removed them had they been a low-temperature martensitic phase, e.g., after an anneal of 1/2 hr at 900°C. When back-reflection Laue data were plotted for single-surface analysis of several grains, every trace of the bands in each grain could be explained by (112) planes. In addition, two of the bands were located in space by traces on two surfaces, and these also were found to lie on (112) planes within the error of the stereographic plot. Since (1 12) is the anticipated composition plane for deformation twins in body-centered-cubic metals it is felt that the observations listed above are conclusive evidence for the identification of the bands as twins. Similar tests with impact at —77° and at 25°C produced no twinning. It is concluded that the critical shear stress for slip at the rates of straining used was always low enough to prevent the applied stress from reaching the value required for twinning at these temperatures. It was noted that the serrations along the edges of the twin bands exhibited parallel crystal facets. Several similarly oriented notches are visible in Fig. 1, and a remarkable set is shown in Fig. 3. It appears from Fig. 1 and similar areas that notches are frequently associated with the intersection of a slip line with a twin, although not all such intersections are at notches. In some instances a slip line appears to enter the twin, cross it, reflect from the opposite side and recross it, producing a pattern resembling a notch but without producing the notch itself, see Fig. 1. It is suggested that the stress concentration at the end of a slip line is responsible for these details. The strain energy associated with the pile-up of dislocations at a twin boundary may be lessened by untwin-ning or failing to twin a portion of the twin band, or

Jan 1, 1959

By H. C. Chang, N. J. Grant, A. R. Chaudhuri

During the creep of coarse-grained polycrystalline magnesium at elevated temperatures, a nonbasal type of slip was found to play an important role in the deformation processes. The nonbasal slip traces were examined metallographically in eight specimens (13 grains) and the observed glide plane located stereographically for each grain. The tests were run at 500&apos; and 700°F at stresses of 148 to 786 psi. Based on these measurements and theoretical calculations, the crystallographic elements for nonbasal slip were determined. WHEN a metal deforms by slip, the conventional appearance of the slip bands on the surface of a specimen is that of straight lines. Such is the behavior of the face-centered-cubic metals, as for example, aluminum. The particular slip system on which slip occurs in these metals is governed by the criterion of resolved shear stress. Work on the body-centered-cubic metals a-iron,&apos;. &apos; molybdenum, and columbium4 has shown that the process of slip is somewhat more complicated than the simple gliding of one close-packed plane of atoms over another in a close-packed direction and that it results in the formation of wavy and irregular slip traces on the surface. The recent reviews and experiments of Vogel and Brick and Chen and Mad-din3 show that, for the body-centered-cubic metals, the resolved shear stresses along the planes and the degree of close-packing do not necessarily determine the slip system. Theirs and other investigations indicate that a complete understanding of the slip process in the body-centered-cubic metals is not yet possible. However, one behavior displayed by all these metals is that the slip direction is invariably one of the close-packed directions <11l>. The wavy nature of the slip-band traces has been explained on the basis of cooperative slip by planes sharing this same slip direction.1&apos;3l&apos; It is generally acknowledged that, when the hexagonal-close-packed metal magnesium (axial ratio c/a = 1.624) deforms by slip at room temperature, it does so by basal slip in the close-packed direction <1I%>. This type of slip has the conventional appearance of straight lines and is governed by the critical shear-stress law. Schmid and coworkers" showed that basal slip was operative in the temperature range of —185" to 300°C (—300" to 572°F). Work by Servi, Norton, and Grant6 has shown that, during the creep of coarse-grained aluminum at high temperatures, new slip systems come into operation. The existence of a new high temperature slip system at temperatures greater than 225 °C (437°F) for magnesium was suggested also by Schmid. This was later indicated by Bakarian and Mathewson&apos; to be slip along the pyramidal planes (10i1) in the close-packed direction <11%>.* They * Mention will be made in the text of pyramidal planes and prismatic planes. The pyramidal planes referred to are the type I. order 1 of the form {10il); and the prismatic planes of the type 1 of the form (10i0). For the sake of brevity, they are termed in the teat as pyramidal (10il: and prismatic (10i0) planes, respectively. Where reference is made to the pyramidal plane type 1, order 2 of the form {10i2), they are referred to as the pyramidal planes of the type (10i2:. observed that this kind of slip resulted in irregular markings on the specimen surface. According to them, a possible cause for the appearance of the markings was due to "limited accessory slip on the pyramidal {10i2) planes." Burke and Hibbard," on deforming a single crystal of magnesium at room temperature, found evidence of slip on a pyramidal plane {1011). They explained it as being due to the effect of grip restraints. It is pertinent to note at this point that, although basal slip has received a fair amount of attention, only two specimens have been investigated, that of Bakarian and Mathewson and of Burke and Hibbard, to establish the elements of nonbasal slip in magnesium. During the study of the deformation mechanisms

Jan 1, 1956

By P More

US 4,132,621-In the electrowinning of aluminum, the cells are aligned in a lengthwise direction so as to lessen the harmful influence of the induced magnetic fields Each cell is supplied with current from the preceding cell both via the head arid at least one side riser The output of the cathode bars is divided into two separate groups, the upstream group supplying the head of the subsequent cell arid the downstream group supplying the side risers of the subsequent cell This produces a substantial improvement in cell efficiency arid a greater regularity P Morel, J P Dugois, arid B Langon, assigned to Aluminium Pechiney. Jan 2, 1979 12 pp. (204¬243M) Filed 1-12-78 (868,861) Priority: France, 1-19-77 (77/2,213) US 4,134,806-Cells, anodes, arid methods for use in the electrowinning of nickel, cobalt, copper, zinc, or other metals from an acid ore leach solution or the like The cell is provided with vertically immersed stationary cathodes and stationary rod anodes which are noncorrodible by the electrolyte arid are electrocatalytic to the anode reaction. The spaced parallel anode rods are connected to electric current supply bars The anode rods have an electroconductive core made of a metal alloy arid a surface coating of an oxide of platinum or a platinum group metal The ratio of active cathode surface area to active anode surface area is preferably at least 3 0. De Nora arid C Traini, assigned to Diamond Shamrock Tech¬nologies, SA Jan 16, 1979 13 pp. (204-105R) Filed 9-15-77 (833,661) Priority Italy, 1-29-73 (19738 A/73). Same British 1,434,334-5, dated May 5, 1976 US 4,135,994-In the electrowinning of aluminum at a high current efficiency, the electrolytic bath is a mixed molten salt consisting of 2-15% by weight of aluminum trichloride, 15-83% of sodium chloride, 15-70% of combined calcium chloride arid magnesium chloride but riot more than 40% of calcium chloride, arid optionally up to 10% of barium chloride Preferably, plate-shaped graphite electrodes used for both cathodes and anodes are arranged in parallel inclined relation so that the axis in the lengthwise direction makes an angle of from 10° to 45° to the horizontal. T Ishikawa arid H Ichikawa, assigned to Nippon Light Metal Co Ltd Jan 23, 1979 4 pp (204-67) Filed 11-15-77(851,632) Same British 1,550,502, dated Aug 15, 1979

Jan 1, 1980

By C. E. SWANN

NOT long ago an engineering study was made to determine if the time had arrived to lower the head of standing water in abandoned Rock Springs mines Nos. I and 3 of The Union Pacific Coal Co. so that this water would not become a menace to the future operations of adjacent mines or mines developed on seams lower in the coal measures. This survey resulted - in a decision to unwater the No. 1 mine workings and, incidentally, the old No. 3 mine workings by drilling a large-diameter hole from the surface to an opening in No. 1 mine at the sump below 21 entry, provided it was found practical to operate a large-capacity, vertical, deep-well pump under the existing conditions. This would relieve the static bead of 200 ft. of water at the fault that separates Rock Springs mines Nos. 1 and 4, which is the

Jan 1, 1935

By AIME

D R. GILLSON, who was born in Evanston, Ill., in 1895, is another one of those geologists who received his early inspiration and foundation in his science from that great teacher at Northwestern University, the late Professor U. S. Grant, and then went on to give his time and interest to Institute affairs-like those other Northwestern men, Arthur Blair, Gilbert Cady, Charlie Behre, Evan Just, Ian Campbell, Clayton Ball, and many others. After serving in the Navy in the first World War as, of all things for a geologist, a commissary officer on a transport, he went on to MIT and took his doctor&apos;s degree under Waldemar Lindgren in 1923. He even assisted in mineralogy at Harvard and thus had training under another great teacher, Charles Palache. He taught mineralogy and petrography at MIT from 1923 to 1928. After several summers of field work as an assistant in the U. S. Geological Survey, Dr. Gillson joined the staff of the du Pont company.

Jan 1, 1947

By R. S. Archer

THE PROPER representation of equilibria involving graphitic carbon in the constitutional diagram of the iron-carbon system is admittedly an unsolved problem. The complete solution of the problem will probably require the establishment of more experimental evidence than is at this time available. The object of this paper is to present the author&apos;s observations on some of the phenomena in question and his interpretation of this and other recorded evidence. The chief of the recently disputed questions upon which the author has experimental evidence concerns the occurrence of graphitization at temperatures below the A1 point. In a paper1 presented at the September, 1919, meeting of this Institute, the following is found: "the results given would seem to indicate that the graphite eutectoid lies at a smaller value of carbon content than has been previously supposed. At least this is true unless there is either a marked formation of graphite eutectoid at these rates of cooling, or a decomposition of pearlite into graphite, both rather unlikely suppositions, but not impossible ones." In a discussion of this paper, H. A. Schwartz2 takes the position that the possibility of graphitization occurring below the A 1 point is an open question, but that complete graphitization (to less than 0.10 per cent. combined carbon) commonly occurs above this temperature. Another opinion from the malleable castings industry is found in a recent paper3 by Touceda: "Also the carbide of iron can be broken up into its two soft constituents at the temperature referred to. This temperature is called the critical temperature, or critical range, and for air-furnace hard-iron castings it is in the vicinity of 1440° F. It is the

Jan 2, 1920

By W. S. Steele

Vermiculite is a nonmetallic mineral of the mica family, probably related to biotite mica. Its occurrence has been noted at numerous places in the United States and in some foreign countries, but it can be said that vermiculite is of only moderately wide distribution. A laboratory and field survey of over 60 deposits in the United States by F. 1;. Schundler & Co., of Joliet, Ill., indicates that the purest deposit represented in this survey is on the property of the Zonolite Company at Libby, Montana The Zonolite Company is commercially active and the vermiculite it produces is sold as Zonolite. Hereafter, in this report, the word "Zonolite " will be used to designate the vermiculite produced by the Zonolite Company. Values given herein to Zonolite are peculiar to the vermiculite produced from the Zonolite Company&apos;s deposits. References to " vermicullite," are to he interpreted as covering the broad field covered by the Schundler survey. Composition and Characteristics of Vermiculite Vermiculite is an aluminum-nmgnesium silicate. The following typical analysis is published by the United States Bureau of Standards: silica, 41 per cent; iron oxide, 7; aluminum oxide, 18; magnesium oxide, 21; calcium oxide, 1; alkalis (sodium and potassium), 1; moisture, 11. Vermiculite breaks down into platelike formation in crushing and grinding operations. Its cleavage is basal. Crude, screened, dry Zonolit,e weighs between 80 and 90 Ib. per cubic foot; its specific gravity is 2.8 and its specific heat is approximately 2. The fusion point of Zonolit&apos;e is 2462" F. Crude vermiculite contains between 7 and 9 per cent of chemically combined moisture. The instantaneous introduction of crude Zonolite into an expansion furnace at a temperature of between 1800" and 2000" F. transforms the combined moisture into steam, which in an effort to liberate itself forces all explosive expansion of the platelike crude material

Jan 1, 1934

By Reino Kurppa

The Pyhäsalmi mine of the Outokumpu Co. is located in central Finland (Fig. 1). The deposit was discovered in the autumn of 1958. Construction of the mine was started a year later, and production began on Mar. 1, 1962 (Fig. 2). At present, 750,000 metric tons (mt) of ore and a nearly equal amount of country rock are mined annually. Slightly over one-half million tons of various concentrates are produced per year, of which 85% is pyrite concentrate, 10% zinc concentrate, and 5% copper concentrate. The pyrite concentrate is treated in the company&apos;s pyrite smelter,1 yielding elementary sulfur, sulfur dioxide, and iron-oxide cinders, as well as electric power. Thus all the sulfides, totaling 75% of the ore, are of economic value. This is a fact which had a bearing on the development of the stoping method. GEOLOGY The ore is of breccia type containing fragments of country rock of varying sizes. It is coarse-grained pyrite ore containing sphalerite and chalcopyrite as a matrix between the pyrite grains. Only small amounts of pyrrhotite have been observed in certain marginal parts of the orebody. The ore averages 0.85% Cu, 3.0% Zn, 38% S, and 33% Fe. The orebody extends from the surface down to at least 500 m, which is the lowest level from which present information has been obtained. Horizontally, the orebody is 650 m long. It is 75 m wide at its central part, narrowing towards the ends (Fig. 3). At a depth of 115 m, the orebody suddenly narrows down to a thickness of 25 to 30 m. In the northern part of the orebody, the dip is 50° to 70°, but elsewhere it is almost vertical (Fig. 3).

Jan 1, 1969

By C. Wagner

When an alloy solidifies and the composition of the solid differs from the composition of the liquid, atoms of the alloying elements rejected at the solid-liquid interface have to diffuse toward the bulk liquid. Diffusion may be supported by convection. Theoretical calculations have been made for a liquid without convection, for a liquid involving natural convection, and for solidification of a liquid alloy at the surface of a rotating disk as an example of forced convection. WHEN an alloy solidifies, the equilibrium composition of the originating solid phase differs in general from the composition of the liquid phase. Thus, segregation may take place, i.e., the composition of the solid phase formed at different times differs from the bulk composition. The degree of segregation depends on several factors such as the partition ratio of the alloying elements between the liquid and the solid phase, the rate of solidification, and convection. To clarify, a theoretical analysis has been worked out. The following presuppositions are made: 1—Calculations are confined to the solidification of binary alloys in which the concentration of component A (solvent) is much greater than that of component B (solute). 2—The equilibrium concentration of the alloying element B is assumed to be lower in the solid phase than in the coexisting liquid phase. 3—At the solid-liquid interface, partition equilibrium is assumed. 4—The dependence of the partition ratio of the solute between the liquid and the solid phase on concentration and temperature is disregarded since only small concentrations of the solute are considered. 5—The concentration of the alloying element B in the solid phase is supposed to be lower than the saturation concentration for the formation of a second solid phase. 6—diffusion in the solid phase is disregarded, since diffusion rates in the solid state are comparatively low. When the partition ratio of the solute between the liquid and the solid phase is greater than unity, a part of the solute is rejected at the solid-liquid inter- face and has to diffuse toward the bulk liquid. Thus there is necessarily a concentration difference in the liquid between the solid-liquid interface and the bulk liquid as has been pointed out by Hayes and Chipman,&apos; Rutter and Chalmers,&apos; Tiller, Jackson, Rutter, and Chalmers, and others (see Fig. 1). In view of the concentration gradient in the liquid phase, the ratio of the concentration of the solute in the solid phase to that in the bulk liquid differs from the equilibrium ratio, although at the solid-liquid interface, partition equilibrium is assumed. Under certain limiting conditions, the solid may even have virtually the composition of the bulk liquid as is shown below. General Equations Let u be the linear crystallization velocity in cm per sec, D the diffusion coefficient of component B in the liquid phase in cm2 sec-&apos;, c&apos;,, and c", the concentrations of component B in the liquid and the solid phase, respectively, in mol per cm", and s the distance from the solid-liquid interface toward the bulk liquid at a given time t. The partition ratio is assumed to be equal to a partition constant K. Thus. The difference in the specific volume between the liquid and the solid phase may be disregarded. In view of the discontinuity of the concentration of the solute at the interface according to Eq. 1, u(c&apos;, — c",), , , = tic&apos;, (S = 0)(1 — K) gram-atoms B per unit area per unit time are rejected at the interface and have to diffuse toward the bulk liquid. From Fick&apos;s first law it follows that uc&apos;,,(s = 0) (1 ~K) == - D(dc&apos;,,/?>s). _-„. [2] The concentration profile in the liquid near the interface depends on the interplay of diffusion and convection as is discussed in the following sections. A schematic concentration profile is shown in Fig. 1. The "effective thickness of the diffusion boundary

Jan 1, 1955

By G. W. Mao, A. M. Gaudin, D. W. Fuerstenau

Activation of sphalerite with copper salts has long been thought of as a chemical reaction of the following form: ZnS + Cu++ [=] CuS + Zn++ [ 1 ] Early experimentation1-3 showed that the reaction seemed to be stopped by the coating of insoluble copper sulfide, but since the analytical methods were crude, it was only surmised that the reaction could proceed by diffusion. Probably the most conclusive evidence for reaction (Eq. 1) was obtained by Cooke,4 who found a stoichiometric replacement of Zn++ by Cu" after 50 days&apos; reaction at about 100°C. Cooke also found the sphalerite to be covered with a rather thick coating of covellite, which in¬dicates that activation is a continuing replacement of Zn++ by Cu" rather than diffusion of Cu" throughout the sphalerite lattice. However, the occurrence of diffusion at high temperatures has been observed.5,6

Jan 4, 1959

By S. W. Parr

THE extent to which geological carbonization has taken place in the process of coal formation is a fundamental factor in all considerations relating to classification, oxidation, deterioration, spontaneous combustion, and especially in all considerations relating to destructive distillation having as an objective the production of marketable coke and by-products. Moreover, it may be readily shown that a. striking relationship exists between the geological decomposition or geological carbonization processes and those artificially produced by heat. This may be well illustrated by bringing again to view some of the charts more commonly met with 25 years ago, as in Fig. 1. 1 FIG. 1. In this figure the line of geological decomposition by decay, pressure, etc., because of its relation to the line of carbonization by destructive distillation, becomes of special significance when we attempt to formulate any system of classification which shall be reasonably scientific and at

Jan 2, 1926

Reno, Nevada. J A Fulton, Director For publications of either the Mackay School of Mines or the State Bureau of Mines, address the School of Mines at the given address. Except where the contrary is indicated in the following list, available publications are sent free From the Mackay School of Mines. Bulletin 1, The identification of Nevada&apos;s common minerals, 50 cents; 3, Notes on the ore deposits of Cave Valley mining district, Lincoln County, 4, A preliminary survey of the Scossa mining district, Pershing County, 5, Ore deposits of the Gold Circle mining district, Elko County, 6, Bedded deposits of manganese oxides near Las Vegas, 7, Spruce Mountain district, Elko County, and Cherry Creek (Egan Canyon) district, White Pine County From the State Bureau of Mines: Bulletin 1, Mineral resources of southern Nevada One volume: Mining districts and mineral resources of Nevada, by F C. Lincoln (1923), $1.50.

Jan 1, 1933

By C. E. MacQuigg

BY and large the education of the engineer has been conservative and the reasons for this are obvious. Quite properly it has been a tradition of engineering education that facts and not fancies must be adhered to. Without a doubt, those men who formed the mold of our engineering philosophy as much as it is possible for such molds to be established-rightly held the highest standards of intellectual honesty. Fortunately, it was unthinkable to them to temporize with untried theories and naturally the men whom they trained as engineering educators carry this philosophy in turn to their students, thus handing down the tradition of stability.

Jan 1, 1943

By M. J. Pool, C. E. Lundin

THE relative partial molar enthalpies of aluminum, gallium, and indium in liquid tin have been measured at 750°K by liquid-metal solution calorimetry. The measured heat effects and the calculated relative partial molar heats of solutions at infinite dilution are listed in Table I along with the relative heat contents of the solutes calculated from the data of Kelley. All of the values are referred to 750°K even though the calorimeter temperature fluctuated by +1°K during the entire series of experiments. The effect of this small temperature variation on the experimental values should be less than the experimental error. The limits of error given in Table I represent the standard deviations of all values from the mean. In no case was the experimental deviation greater than the listed error limits. The reported error estimates only apply to the estimated precision of experimental values and not to their accuracy. Systematic errors could be present in the calorimeter which would affect the absolute values given. Moreover the heat-content data used could also be in error and this would affect the end results. The relative enthalpies used were listed in Table I so that future corrections could be made if necessary. The relative partial molar heats of solutions of aluminum in liquid tin and dilute A1-Sn liquid solutions are large and positive. The value at infinite dilution is given in Table I. In the dilute-solution region investigated the relative partial molar heat of solution was a linear function of composition. A least-squares analysis of the data gave the following expression at 750°K: Atf^ = 6195 - 12,160 A:A1(cal/g-atom) where XA1 is the mole fraction of aluminum in the alloy. This can be compared with the data of Cohen, Howlett, and ever&apos; who obtained the expression: 1SM = 6075 - 10,750 XM at 573°K Apparently both the partial molar heat of solution at infinite dilution and the concentration dependence increase with increasing temperature. This same

Jan 1, 1964

By G. D. Rieck, G. H. G. Vaessen, D. L. Vogel

Both doped and undoped tungsten single crystals exhibit hardness anisotropy with respect to the direction of testing in each of the crystallographic phes investigated. The hardness anisotropy of undoped single-crystal tungsten is rather pronounced in (001) and (110) planes but very minor in (111) planes. The anisotropy in (122) planes of the doped and drawn tungsten after recrystallization is in accordance with a previously published concept of a stringlike distribution of the doping material in the metal. ANISOTROPY in mechanical properties of single-crystal tungsten was investigated by Rose et al., Garlick and Probst,2 and Beardmore and Hull. 3 Although data on the Vickers microhardness of tungsten have been published (see, e.g., Boosz 4 and the references cited by him), no data on the microhardness anisotropy are available. We report, therefore, some of our own results on the microhardness and its anisotropy. The microhardness has been determined of the following samples. A) Polycrystalline tungsten samples taken from: 1) powder metallurgical tungsten "normally" doped with potassium-silicon-aluminum oxides (final contents inppm: K, 100; Si, 100; Al, 20; Cr, 20; Fe, 50; Mo, 400; Ni, 10) and in the form of: a) a 10-mm-diam swaged ingot annealed at 1600°C, the grain sizes varying between 15 and 250 p; b) a sheet rolled at about 800°C and recrystallized at 2000°C7 the grain sizes varying between 15 and 150 p; c) a 2-mm-diam swaged rod, as-worked, with elongated grains (average diameter of about 25 , lengths up to 1 mm); 2) undoped electron-beam-melted tungsten with very large grains (contaminations in ppm: K < 10; Fe < 20; Cr < 10; Cu < 0.1; Ni not detectable; inter-stitial~ not determined). B) Single-crystal samples taken from: 1) pure tungsten grown on a Pintsch wire by the van Arkel procedure (main contaminations inppm: Mo, 100; Si < 10; Cu and Fe, 2; A1 < 2; interstitials not determined); 2) zone-melted undoped tungsten (analysis as under A2); 3) large crystals in secondary recrystallized tungsten

Jan 1, 1969

By N. J. Grant, A. W. Mullendore, Y. Ishida

Creep tests were performed at 500°F on polished specimens of A1-3 pct Cu at stresses of 2000, 4000, and 6000 psi. The effects of the size and distnbution of the second phase were studied in connection with the mechanisms of deformation, especially grain boundary sliding. Although the amount of grain boundary sliding varied considerably for the different heat treatments, yestriction of grain boundary sliding is not due primarily to precipitate on the grain boundary. NUMEROUS prior investigations of grain boundary sliding, notably those of McLean, 1 Rachinger, 2 Rhines, Bond, and Kissel, 3 and Brunner and Grant,4 have established the importance of this phenomenon in the deformation of pure aluminum and its solid-solution alloys at elevated temperatures. An extension of this kind of study to the case of a simple two-phase structure is an important step towards understanding the deformation behavior of more complex alloys. A two-phase A1-3 pct Cu alloy was selected for this study. The creep behavior of alloys in this system has been studied by Sully and Hardy,5 by Underwood, Marsh, and Manning,&apos; and by Pelloux, Chaudhuri, and Grant.7 In these studies, the prior heat treatments were such that some precipitation took place during the tests in most cases. Pelloux, Chaudhuri, and Grant7 studied the creep of A1-2 and 3 pct Cu alloys in the overaged condition. Their results indicated that the structure most effective in promoting high-temperature strength consisted of a fine, closely spaced grain precipitate and large, widely spaced particles on the grain boundary. The present work consists of quantitative meas- urements of grain boundary sliding during creep of an A1-3 pct CU alloy with four different precipitate distributions. The aims were to quantitatively define the role of the second phase on grain boundary sliding, and to obtain information regarding the mechanism of grain boundary sliding. MATERIALS AND PROCEDURE A high-purity A1-3 pct Cu alloy, kindly supplied by Alcoa, was used in this investigation. The composition of the alloy in weight percent was as shown in Table I. This composition is such that A12Cu exists as a second phase at temperatures below 850°F. A homogeneous grain size of 0.6 to 0.8 mm was obtained by annealing the machined test bars for 5 min at 1000°F, furnace cooling to 930°F, and homogenizing for 5 hr. Following the recrystalli-zation and homogenizing anneal, four different heat treatments shown in Fig. 1 were utilized. The F7 and F5 treatments utilize a furnace cool to the aging temperature while Q7 and Q5 have a water quench from the homogenization temperature before aging. Figs. 2 to 5, and Table 11, show the size and shape of precipitate dispersions obtained with the above heat treatments. The heat treatments produce variations in the dispersion both in the grains and along the grain boundaries. Precipitate particles along the grain boundaries are rounded and large (about 1.5 p diameter) in the F5 and F7 structures (Figs. 3 and 5). The grain boundary precipitate was somewhat smaller (0.9 p diameter) in the Q7 structure and no grain boundary precipitate was detected in the Q5 structure using light microscopy. The pre-

Jan 1, 1964

By David J. Mack, T. V. Philip

The effects on the Cu-A1 eutectoid transformation of the addition of a third element from the second long period and from Group IIB of the periodic table, were studied by isothermal transfomation techniques. The valency of the third element shows the most pronounced effect on the eutectoid decomposition. With some exceptions, the atomic size factor of the third element shows some consistent effects on pearlite nucleation and growth. The atomic concentration or the electronegative valency of the third element shows wo consistent effect on the eutectoid decomposition. Addition of the third element helps spheroidization of pearlite. SINCE the pioneering work of Davenport and Bainl on the eutectoid decomposition in steel by the isothermal transformation technique, an enormous amount of data has been accumulated on the eutectoid transformation characteristics of commercial steels. While the eutectoid reaction in steel is of tremendous industrial importance, it appears to be quite unique among the eutectoid reactions. Though the metal-lographic structures developed in the Fe-C and Cu-A1 eutectoids are similar, it is now evident that the two eutectoid reactions are quite dissimilar. The eutectoid decomposition in the Cu-A1 system is more complicated partly due to the appearance of transitional phases in addition to the equilibrium phases. * The first isothermal studies of aluminum bronzes were made by Smith and Lindlief2 and later by Mack,3 Klier, and Grymko,4 and recently Hayne 5,6 A few other systems, structurally analogous to the above, have been studied by the same technique.7-10 Kasberg and Mack1&apos; studied the effects of iron on the transformation of commercial aluminum bronze. The effects of manganese and nickel on this aluminum bronze and those of iron, manganese, and nickel on the binary Cu-A1 eutectoid have been recently studied.12 The object of the present investigation was to study, by isothermal transformation techniques, the effects (with respect to the fundamental factors of alloy formation) of the addition of a third element on the transformation of a Cu-Al eutectoid alloy, 11.8 pct Al. The third elements chosen for the purpose were silver, cadmium, indium, tin, and antimony from the second long period, and beryllium, zinc, and cadmium from group 11B of the periodic table. They were added in nominal amounts of 0.5, 1.0, and 2.5 pct by weight to a eutectoid Cu-A1 alloy. These third elements were expected to show the effects of electron valency, atomic size factor, and electronegative valency effects on the binary eutectoid transformation. PFLEPARATION OF ALLOYS AND PROCEDURE All alloys were made as 400-g heats by induction melting in a graphite crucible with a graphite lid. The molten alloy with a layer of graphite powder on top was stirred at regular intervals by a graphite rod. When the melt was judged to have acquired sufficient superheat, a pinch of common salt was sprinkled on top and any crust scraped off to one side. It was then chill cast into a 5/8 in. rod. The alloys with silver were prepared by remelt-ing the high-purity Cu-A1 eutectoid alloy used by Mack3 with high-purity silver (99.99 pct pure from Hardy and Harmon, Inc.). In the preparation of all the other alloys, polished electrolytic copper shot (from Belmont Smelting and Refining Co.) and high-purity aluminum (99.99 pct pure from Aluminum Co. of America) were used.

Jan 1, 1962

By Philip Kraft

WHEN it came time to write a biography of Philip Kraft, we got out a copy of Bartlett&apos;s "Familiar Quotations" and looked through the references to Travel, Traveled, Traveler, and Traveling, feeling sure there would be some reference to Mr. Kraft. Sure enough, we found: "Travel, in the younger sort, is a part of education; in the elder, a part of experience." Had Francis Bacon done his writing three and a half centuries later, Mr. Kraft might well have served as the inspiration for that sentence. New Yorker born, he received his B.S. and E. M. degrees from Columbia. In 1912, then 22 years old, he took off for Germany where he spent two years studying at the Royal School of Mines, Berlin, for his Doctor of Engineering degree. Contrary to the Greeley-Soule precept, Mr. Kraft, on his return from Europe, went north to South Porcupine. Ont., working as geologist and mining engineer for the Dome Mine. From South Porcupine his next stop was Washington, D. C., where, during the years the country was in the first World War, he was engaged in war work.

Jan 1, 1947