Search Documents

J: H. POLHEMUS, New York, N. Y. (written discussion*).-The Joplin .mining and milling practice has largely influenced operating methods in the Wisconsin district. Milling equipment is essentially of the same type with the notable exception that no tables are used. The treatment of the flue 'sands has been attempted several times but without commercial success. Table material coming from any one mill is low both in tonnage and zinc content. The iron is comparatively high as the pyrite-line "chat" is much more prevalent than the zinc-lime attached particle. In the finer sizes the zinc occurs mainly as free mineral. These condi-tions make the production of good-grade table concentrates very diffi-cult. The accompanying tabulated results from several mill tests indi-cate the character of the mill tails. I think the average mill tails in the district assay nearer 1.5 per cent. zinc than under 1 per cent., as stated by Messrs. Boericke and Garnett.

Jan 10, 1919

By Luckie. Peter T., Deurbouck. A. W., Harold L. Lovell, E. R. Palowitch, James K. Kindig

PART 1: DENSE MEDIUM SEPARATION by E. R. PALOWITCH and A. W. DEURBROUK INTRODUCTION During 1974, 43.9% of the 603,406,000 tons (549,099,000 mt) of bituminous coal and lignite produced was cleaned mechanically, of which 82,280,000 tons (74,875,000 mt) was cleaned by dense medium processes.l The percentage of bituminous coal and lignite cleaned mechanically by dense medium processes increased from 7 to 31 % between 1938 and 1974. Dense medium separations include those coal preparation processes which clean raw coal by immersing it in a fluid having a density inter- mediate between clean coal and reject. As there is a general correlation between ash content and specific gravity, it is possible to achieve the required degree of removal of ash-forming impurities from a raw coal by regulating the specific gravity of the separating fluid. Dense medium processes offer the following advantages over other coal cleaning processes: 1) Ability to make sharp separations at any specific gravity within the range normally required even in the presence of high percentages of the feed in the range of 2 0.1 sp gr units. 2) Ability to maintain a separating gravity that can be controlled with ± 0.005 sp gr units.

Jan 1, 1979

By F. Kurata, A. F. Bertuzzi, P. C. Davis, T. L. Gore

The phase and volumetric properties of 10 very volatile mixtures are presented for temperatures from — 200°F to above the critical points. These mixtures consisted of natural gases and of mixtures of natural gases with methane and nitrogen. Existing correlations of compressibility factors have been extended to apply to these mixtures. Existing correlations of critical pressures and temperatures do not apply to these mixtures. Methods have been developed for estimating critical temperatures of these mixtures to ± 4°F and critical pressures to 2 5 per cent. These methods apply to other volatile and very volatile mixtures. The results of this work are particularly applicable to the separation of nitrogen from hydrocarbons by low-temperature distillation. INTRODUCTION Knowledge of the low-temperature phase and volumetric properties of natural gases and of other mixtures of the light hydrocarbons is becoming increasingly important as interest in low-temperature separation processes increases. Low-temperature distillation has been used to separate ethane and ethylene from natural gas and from refinery gases for petrochemical uses. Removal of nitrogen from natural gas by low-temperature distillation has been proposed 7,20 as a means of increasing the capacity of existing gas transmission lines and of improving the marketability of the gas. Further application of low-temperature separation processes has been retarded by lack of data on the phase and volumetric behavior of mixtures at low-temperatures and at high pressures. This paper presents the results of determination of the phase and volumetric properties of 10 very volatile mixtures at temperatures from - 200 °F to above the critical point. These mixtures consisted of natural gases with methane and nitrogen. Generalized methods are presented for estimating the critical temperatures, critical pressures, and the densities of such mixtures. EXPERIMENTAL APPARATUS AND PROCEDURES The apparatus and the experimental procedures have been described in an earlier paper13. The method consists of displacing the mixture from a reservoir which is maintained at constant temperature and pressure into an agitated glass equilibrium cell which is maintained at constant temperature. The liquid level within the glass equilibrium cell was visually observed, and the pressure was measured to within & 3 psi with a calibrated Bourdon gage. COMPOSITIONS OF MIXTURES STUDIED The compositions of the mixtures studied are summarized in Table 1. The measured properties included in Table 1 will be discussed later in this paper. The sources of these gases are described below: Gas "A-1'' was obtained from the Phillips Petroleum Co. Its composition was reported in connection with earlier work." The properties of this gas were reported in an earlier paper.13 Gases "A-2, A-3, A-4" were prepared by mixing nitrogen with gas "A-1." Gas "AB-1" was prepared by mixing methane with gas "A-1." The properties of this gas were reported in an earlier paper.'" Gases "AB-2" and "AB-3" were prepared by mixing nitrogen with gas "AB-1." Gas "B" was obtained by W. W. Bodle of J, F. Pritchard & Co. from the primary separator of a well in western Kansas. Gas "C" was obtained from a Cities Service Co. pipeline at Lawrence, Kans. Gas "D" was prepared by mixing gas "AB" with gas "C."

Jan 1, 1955

By C. A. Heiland

THE investigations described were made on a portion of Clear Creek basin near Golden, Colo. (A portion of the area under survey is shown in Fig. 1. The photograph was taken in the vicinity of station No. 2 of Line II.) Three principal purposes were in the minds of the investigators: 1. To repeat with modern, more sensitive and more reliable instruments magnetometric placer investigations previously made. 2. To disprove the recently advanced theory that deposits of the glacial period have no pronounced magnetic effects. 3. To develop in detail the theory of the magnetic effects produced by placer deposits. Six years ago, the first magnetic observations were published, which proved that it is possible to locate gold-bearing channels with relatively crude instruments.1 Two years ago, K. C. Laylander published results obtained with similar instruments.2 The measurements of the latter were discussed by the senior author of this paper.3 At that time, however, the material available for such a discussion was somewhat scarce and not made with the most modern magnetic instruments, although very brilliant results were obtained. Therefore, the senior author felt that magnetic investigations should be made on very clear geologic conditions with the most modern instruments.

Jan 1, 1928

NAME AND OBJECT. SEc. 1. This Institute is incorporated under the Membership Corporations law of the State of New York ; its corporate name is American Institute of Mining Engineers; and its objects are such as are stated in its Certificate of Incorporation. ARTICLE II. MEMBERS. SEC. 1. The membership of the Institute shall comprise four classes, namely 1. Members ; 2. Honorary Members ; 3. Associates ; 4. Junior Members. All members shall be equally entitled to the privileges of membership, except¬ing that Honorary Members, Junior Members, and Members and Associates whose residences shall be outside of the United States, Mexico, and Canada shall not be entitled to vote. Members and Associates residing within the United States of America, Mexico, and Canada, and not in arrears for dues, shall be entitled to vote in person at the meetings of the Institute, or, as hereinafter provided for, by letter ballot. SEC. 2. The following classes of persons shall be eligible for membership in the Institute, namely : as Members, all professional mining . engineers, geologists, metallurgists, or chemists, and all persons actively engaged in mining and metal¬lurgical engineering, geology, or chemistry ; as Associates, all persons desirous of being connected with the Institute who in the opinion of the Board of Directors are suitable.

Jan 1, 1923

NAME AND OBJECT. SEc. 1. This Institute is incorporated under the Membership Corporations law of the State of New York ; its corporate name is American Institute of Mining Engineers; and its objects are such as are stated in its Certificate of Incorporation. ARTICLE II. MEMBERS. SEC. 1. The membership of the Institute shall comprise four classes, namely 1. Members ; 2. Honorary Members ; 3. Associates ; 4. Junior Members. All members shall be equally entitled to the privileges of membership, except¬ing that Honorary Members, Junior Members, and Members and Associates whose residences shall be outside of the United States, Mexico, and Canada shall not be entitled to vote. Members and Associates residing within the United States of America, Mexico, and Canada, and not in arrears for dues, shall be entitled to vote in person at the meetings of the Institute, or, as hereinafter provided for, by letter ballot. SEC. 2. The following classes of persons shall be eligible for membership in the Institute, namely : as Members, all professional mining . engineers, geologists, metallurgists, or chemists, and all persons actively engaged in mining and metal¬lurgical engineering, geology, or chemistry ; as Associates, all persons desirous of being connected with the Institute who in the opinion of the Board of Directors are suitable.

Jan 1, 1917

NAME AND OBJECT. SEC. 1. This Institute is incorporated under the Membership Corporations law of the State of New York ; its corporate name is American Institute of Mining Engineers; and its objects are such as are stated in its Certificate of Incorporation. ARTICLE II. MEMBERS. SEC. 1. The membership of the Institute shall comprise four classes, namely 1. Members ; 2. Honorary Members ; 3. Associates ; 4. Junior Members. All members shall be equally entitled to the privileges of membership, except¬ing that Honorary Members, Junior Members, and Members and Associates whose residences shall be outside of the United States, Mexico, and Canada shall not be entitled to vote. Members and Associates residing within the United States of America, Mexico, and Canada, and not in arrears for dues, shall be entitled to vote in person at the meetings of the Institute, or, as hereinafter provided for, by letter ballot. SEC. 2. The following classes of persons shall be eligible for membership in the Institute, namely : as Members, all professional mining . engineers, geologists, metallurgists, or chemists, and all persons actively engaged in mining and metallurgical engineering, geology, or chemistry ; as Associates, all persons desirous of being connected with the Institute who in the opinion of the Board of Directors are suitable.

Jan 1, 1923

By Harry R. Hall

The proposition to make pig-iron from magnetic concentrates and cobbed ore with charcoal-fuel weighing from 12 to 20 lb. per bushel is, on the face of it, not inviting; but the work that has been done under these adverse conditions may be worthy of record as furnishing a comparison with coke blast-furnace practice under similar conditions.' The record of the furnace-practice is briefly summarized as follows :—the charcoal was made of hemlock, pine, spruce, balsam, maple, beech and birch woods. All the concentrates, containing from 62 to 65 per cent. of iron, would pass 1/8in. screen, of which about 34 per cent. would pass an 80-mesh screen. The cobbed ore, varying in composition from 32 to 47 per cent. of metallic iron and from 23 to 32 per cent. of silica, would pass through a 1-in. ring, and of this ore about 25 per cent. would pass a 1/8-in. screen. The furnace was blown-in October 20, 1903, with charcoal which was supposed to weigh, when dry, 18 lb. to the bushel. Some charcoal similar to this was stored in the stock-house for about a year, and was then found to weigh 12 lb. per bushel.

Jan 1, 1906

By C. F. Smart

THE heat treatment of the bronze composed of 88 per cent. copper, 10 per cent. tin, and 2 per cent. zinc, has been investigated by H. S. and J. G. S. Primrose,1 and also by the U. S. Bureau of Standards.2 The results obtained by H. S. and J. G. S. Primrose on dry-sand castings subjected to reheating followed by air cooling, or by quenching in water, are shown in Figs. 1 and 2. The values for tensile strength have been FIG. 1.-EFFECT OF QUENCHING ON DRY SAND CASTINGS (H. S. AND J. G. S. PRIMROSE.) converted from tons per square inch to pounds per square inch. Figs. 3and 4, have been plotted from values obtained by the Bureau of Standards on material of the same composition and treatment. Both investigations show that the ductility of the cast bronze is improved by heating to 700° C. and cooling in air, the strength not being impaired by this treatment. They are not in agreement, however, as to the effect of quenching, Messrs. Primrose reporting a decrease, and the Bureau of Standards an increase, in both strength and ductility when the cast bronze is heated to 600° or 700° C. and quenched.

Jan 9, 1919

By R. V. Whetsel, V. R. Garfias

It is estimated that during 1936 world consumption of petroleum, its products and related fuels reached an all-time peak of 1,757,778,000 bbl., an increase of 143,000,000 bbl. over 1935. As indicated in Table 1, world output of petroleum and related fuels exceeded demand by 92,510,000 bbl. during the year, as compared to an excess output of 88,000,000 bbl. during 1935. Production within the United States exceeded domestic demand by approximately 51,000,-000 bbl. in 1936, as compared to an excess output of 53,000,000 bbl. in the previous year. Outside the United States, production exceeded demand by 41,510,000 bbl. in 1936 and by 35,000,000 bbl. in 1935, indicating that foreign output is making no progress toward curtailment in line with demand. Table 1 also combines excess production in the United States with the favorable balance of exports over imports, showing that stocks in the United States were reduced by 23,400,000 bbl. in 1936, as compared to 22,447,000 bbl. in the previous year. In the rest of the world, excess output over demand combined with the excess of imports over exports from the United States indicates an unfavorable balance of approximately

Jan 1, 1937

NAME AND OBJECT. SEc. 1. This Institute is incorporated under the Membership Corporations law of the State of New York ; its corporate name is American Institute of Mining Engineers; and its objects are such as are stated in its Certificate of Incorporation. ARTICLE II. MEMBERS. SEC. 1. The membership of the Institute shall comprise four classes, namely 1. Members ; 2. Honorary Members ; 3. Associates ; 4. Junior Members. All members shall be equally entitled to the privileges of membership, except¬ing that Honorary Members, Junior Members, and Members and Associates whose residences shall be outside of the United States, Mexico, and Canada shall not be entitled to vote. Members and Associates residing within the United States of America, Mexico, and Canada, and not in arrears for dues, shall be entitled to vote in person at the meetings of the Institute, or, as hereinafter provided for, by letter ballot. SEC. 2. The following classes of persons shall be eligible for membership in the Institute, namely : as Members, all professional mining . engineers, geologists, metallurgists, or chemists, and all persons actively engaged in mining and metal¬lurgical engineering, geology, or chemistry ; as Associates, all persons desirous of being connected with the Institute who in the opinion of the Board of Directors are suitable.

Jan 1, 1917

By Peter L. Raffo, Walter R. Witzke

RHENIUM has a melting point of 5750°F, the second highest value among the metals.1 Its refractory nature should thus make it a useful material at high temperatures. The only available data on the high-temperature properties of bulk rhenium are from the work of Flagella and Tarr.2 These authors have shown that, over a wide range of temperatures and stresses, no appreciable linearity exists in a log-log plot of the minimum creep rate or rupture life vs stress. The purpose of the present letter is to describe some exploratory experiments designed to study the creep rate-stress-temperature relation and other facets of the creep of rhenium. The tests were carried out in vacuum in the temperature range 2200" to 4000°F (0.43 to 0.72 Tm,) at stresses ranging from 4 to 20 ksi. The powder metallurgy rhenium was purchased as 0.04-in.-thick sheet. The sheet is nominally 99.97 pct pure with the major impurities being iron (70 ppm) and molybdenum (25 ppm). The sheet was machined into specimens having a 1-in. gage length and a 0.25-in. gage width. The specimens were preannealed in hydrogen at 3000°F for 1 hr. This treatment produced

Jan 1, 1970

By K. D. Jacob

ALL types of commercial phosphate rock produced throughout the world contain fluorine in quantities ranging from approximately 0.4 to 1.3 per cent in the Curacao and Christmas Island phosphates to 3.1 to 4.2 per cent in the phosphates of the United States and North Africa1. For a given type of rock, the fluorine content is usually roughly propor-tional to the phosphorus content. SIGNIFICANCE OF FLUORINE IN PHOSPHATE ROCK On the basis of chemical and X-ray diffraction studies, Hendricks and co-workers2 concluded that fluorapatite, Ca10F2(P04)6, is the essential phosphatic constituent of the commercial types of domestic phosphate rock. On the other hand, Bredig and co-workers3 have recently advanced the opinion, also based on X-ray diffraction studies, that the mineral phosphates usually contain carbon dioxide in the apatite lattice, and that the phosphate rocks of. the United States are really fluorcarbonate apatites. However, the domestic types of phosphate rock do not seem to differ greatly from coarsely crystalline fluorapatite in their behavior toward chemical reagents in general, and for the purpose of this paper it will suffice to consider fluorapatite as being the essential phosphatic constituent of these types of rock.

Jan 1, 1936

By H. Hance James

SOME of the outstanding features of petroleum production in Illinois during 1923 were: (1) Sustained production from the older wells, due to cleaning and deepening; (2) good results from new drilling in a few localities; (3) large percentage of dry holes, many of which were ill advised tests, with a resulting high cost of the new production; (4) decrease in the number of productive wells in the state; (5) low average price of crude petroleum, a serious factor over the entire country. FIG. 1.-ANNUAL TOTALS OF ILLINOIS PRODUCTION. The total production of Illinois for 1923 was 8,710,000 bbl.,1 a decrease of 7.2 per cent. from that of 1922. Of this amount, it is estimated that about 8,500,000 bbl. were produced by old wells, many of which had been cleaned and deepened somewhat, and approximately 210,000 bbl. were obtained from the new wells drilled during the year. About 95 per cent. of the oil comes from the southeastern field in Clark, Crawford, and Lawrence Counties, where production is almost entirely from Pennsylvanian and Mississippian rocks. Extensions of the productive area were made in Clark, Wabash, Marion, and Jackson Counties. Some important gas development has been accomplished near Jacksonville, in Morgan County, and at Gillespie, in Macoupin County.

Jan 3, 1924

NAME AND OBJECT. SEC. 1. This Institute is incorporated under the Membership Corporations law of the State of New York ; its corporate name is American Institute of Mining Engineers; and its objects are such as are stated in its Certificate of Incorporation. ARTICLE II. MEMBERS. SEC. 1. The membership of the Institute shall comprise four classes, namely 1. Members ; 2. Honorary Members ; 3. Associates ; 4. Junior Members. All members shall be equally entitled to the privileges of membership, except¬ing that Honorary Members, Junior Members, and Members and Associates whose residences shall be outside of the United States, Mexico, and Canada shall not be entitled to vote. Members and Associates residing within the United States of America, Mexico, and Canada, and not in arrears for dues, shall be entitled to vote in person at the meetings of the Institute, or, as hereinafter provided for, by letter ballot. SEC. 2. The following classes of persons shall be eligible for membership in the Institute, namely : as Members, all professional mining . engineers, geologists, metallurgists, or chemists, and all persons actively engaged in mining and metallurgical engineering, geology, or chemistry ; as Associates, all persons desirous of being connected with the Institute who in the opinion of the Board of Directors are suitable.

Jan 1, 1923

NAME AND OBJECT. SEc. 1. This Institute is incorporated under the Membership Corporations law of the State of New York ; its corporate name is American Institute of Mining Engineers; and its objects are such as are stated in its Certificate of Incorporation. ARTICLE II. MEMBERS. SEC. 1. The membership of the Institute shall comprise four classes, namely 1. Members ; 2. Honorary Members ; 3. Associates ; 4. Junior Members. All members shall be equally entitled to the privileges of membership, except¬ing that Honorary Members, Junior Members, and Members and Associates whose residences shall be outside of the United States, Mexico, and Canada shall not be entitled to vote. Members and Associates residing within the United States of America, Mexico, and Canada, and not in arrears for dues, shall be entitled to vote in person at the meetings of the Institute, or, as hereinafter provided for, by letter ballot. SEC. 2. The following classes of persons shall be eligible for membership in the Institute, namely : as Members, all professional mining . engineers, geologists, metallurgists, or chemists, and all persons actively engaged in mining and metal¬lurgical engineering, geology, or chemistry ; as Associates, all persons desirous of being connected with the Institute who in the opinion of the Board of Directors are suitable.

Jan 1, 1923

By M. C. Fuerstenau

Each year during the AIME Annual Meeting, the MBD Division has its Business Meeting. Because many members cannot attend, it has be- come policy for the secretary of the Division to present highlights of the business conducted at the Meeting in Fine Grind. This year the Meeting was held on March 1 in the Americana Hotel. Five major items of business were brought up for discussion. These were: (1) the proposed name change for the Division, (2) institution of the Taggart Award, (3) a name change for a Unit Committee, (4) MBD funding of scholarships, and (5) authorship of Fine Grind articles. The Matter of What We Should Call Ourselves A lively discussion was held on the issue of a name change for the Division. Two names have been proposed: (1) Mineral Processing Division, and (2) Mineral Engineering Division. A number of strong reasons for changing the name from Minerals Beneficiation Division have been pointed out. Perhaps the most important of these is that the term "beneficiation" does not describe all of the functions that engineers in our Division perform. Further, there are inherent problems associated in the term, in that beneficiation is a long word which has the twofold disadvantage of being both difficult to pronounce and difficult to spell.

Jan 1, 1971

By G. Richards Gwinn

THE mineral graphite has been known for hundreds of years and was first used commercially as a coloring agent. Its true identity, however, was not recognized until the end of the eighteenth century and its commercial development did not become extensive until near the close of the nineteenth century. The common names for this mineral are graphite, plumbago, and black lead; others less frequently used are potelot, crayon noir, carbo mineralis, and kish. Graphite was named by Johann Gottlieb Werner in 1789 from the Greek word graphein, to write, and this name was applied primarily to the large crystalline, flake variety. Plumbago is a trade term used primarily for massive graphite as found in Ceylon. Black lead is also a trade term and, like plumbago, is based upon the idea that prevailed throughout the Middle Ages that graphite was a form of lead, or at least contained that metal. Graphite is a soft, black, unctuous form of carbon that crystallizes in the hexagonal system with rhombohedra1 symmetry. It occurs occasionally in six-sided tabular crystals but usually is found in foliated masses, minute disseminated scales, or earthy lumps. It has perfect basal cleavage, is gray to black, has a metallic luster and a gray streak. The specific gravity is 2.1 and hardness is 1 to 2. It is opaque even in finest particles; extremely resistant to the action of acid or heat; and a good conductor of both heat and electricity. Graphite may be separated into three classes: ( ) natural, (2) manufactured (which is sometime called artificial), and (3) colloidal. Natural graphite is divided into two classes, "crystalline" and "amorphous." Crystalline graphite may occur as flake, lump, chip or dust. Amorphous graphite is a commercial term only, as all graphite is crystalline, but grades in which the individual grains cannot be distinguished are classified by the trade as amorphous. Natural mixtures of crystalline and amorphous occur in all proportions. The term "artificial graphite" is a misnomer; "manufactured graphite" is a better term, because it actually is pure crystalline graphite,

Jan 1, 1949

By Y. C. Liu, W. R. Hibbard

An aluminum single crystal cold-rolled from (110) [1121 essentially retains its initial orientation after 99.6 pct reduction in thickness. The orientation of the recrys-tallized grains of this material can be described in terms of crystallographic rotations about principal poles of deformation texture. DURING the study of the recrystallization of a copper single crystal cold-rolled from a (110) [112] initial orientation, the orientation of the re-crystallized grains could be derived by a 30" rotation of the orientation of the cold-rolled matrix about its <111> poles.&apos; The present investigation was undertaken to extend the work done on copper&apos; to an aluminum crystal also cold-rolled from a (110) [112] initial orientation. Experimental Procedure The procedure of this experiment was similar to that reported for copper.&apos; An aluminum (99.998 pct) single crystal rod* 1 % in. in diameter was grown in back-reflection technique.&apos; The specimen (1.20x 1.004x0.6787 in. thick) was then rolled along the [112] direction. The final thickness was 0.0028 in., giving a reduction in thickness of about 99.6 pet. Specimens were cut from the rolled strip with scissors, and approximately in. of disturbed metal was removed with Tucker&apos;s reagent. The rolling edge remained intact. The specimens were sandwiched between two graphite plates and annealed in a lead or lead alloy bath which was electrically heated. Pole figures were constructed using the techniques previously described.&apos; Specimens were electrolytically polished4 and etched with 47 pct HNO8, 50 pct HC1, and 3 pct of 48 pct HF. The electrolytic polishing method and etching reagent employed for aluminum specimens were not entirely satisfactory and the microstruc-tures could not be studied in any detail. Results and Discussion The octahedral pole figure of cold-rolled aluminum strip is plotted in Fig. 1. The <111> poles spread in the transverse direction approximately 8" for the highest intensity areas. The spread in the transverse direction can be related to a rotation about two <110> directions lying in a plane containing the rolling direction and rolling plane normal. The two <110> directions and a scale of rotation for the <111> poles are shown in Fig. 2. The amount of rotation is consistent for three of the four <111> poles, about 35" to 40". The discrepancy for the fourth pole is believed to be due to limitations of the film technique. Alternate inter-

Jan 1, 1956

By T. B. Massalski, H. W. King

An hcp phase may be induced by cold working the ß&apos; phase of the Ag-Zn system. This phase reverts to ß&apos; on subsequent aging. No phase change occurs on cold working the o phase, but ß&apos; is formed when the deformed alloy is subsequently aged at room temperature. It is concluded that for alloys near 50 at pct Zn the ordered bcc ß&apos; phase is the equilibrium structure at room temperature. WhEN the disordered bcc ß phase of the Ag-Zn system is cooled to temperatures below 258o to 274oC, it transforms to a complex hexagonal phase <o.1,2 The nature of the o ß=o transformation has been the subject of some discussion,2&apos;3 and the structure of o has been described in detail.&apos; The latter phase appears to be stable on aging at room temperature but decomposes following cold work. When alloys containing approximately 50 at. pct Zn are rapidly quenched from the 0 phase field, the ß ? o transformation may be suppressed; but the ß phase undergoes an ordering reaction (ß ? ß&apos;). The ß&apos; structure may also be obtained as a result of cold working and aging at room temperature.4 Kitchingman, Hall, and Buckley4 have suggested that the decomposition of (o following cold work proceeds in two stages, (o ? ß followed by ß ? ß&apos;, but did not confirm this by experiment. When the ordered &apos; phases in the systems Cu-Zn5 and Ag-Cd6 are cold worked, they become unstable and transform to a close-packed hexagonal phase (( ) indicating that when order is destroyed in a ß&apos; structure the close-packed hexagonal phase may in many cases be more stable. It thus became of interest to study more closely the effect of cold work and annealing on the stability of both the ß&apos; and o phases in a Ag-50 at. pct Zn alloy. Predetermined weights of spectroscopically-pure Ag and Zn, supplied by Johnson and Matthey, were melted and cast under 1/2 atm of He in transparent vycor tubing. The ingot was homogenized for 1 week at 630°C and quenched into iced brine. Since mechanical polishing was found to induce a phase change, sections were first polished at room temperature, sealed in tubes under 1/2 atm of He, reannealed for several days at 630o or 200°C and then quenched into iced brine. Sections of the alloy thus prepared were found to be homogeneous when examined under the microscope. The sample quenched from 630°C (ß -phase region) was pink in color, whereas the sample quenched from 200°C (o-phase region) was silver. The latter sample showed the characteristic hexagonal anisotropy when examined under polarized light. Filings of the alloy were examined at room temperature, after various heat treatments, using an RCA-Siemens Crystalloflex IV diffractometer with filtered CuKa radiation. The X-ray reflections from flat powder specimens quenched from 630o and 200°C and sieved through 230 mesh were recorded graphically at a scanning speed of 1/2 deg per min. The resultant patterns are shown in Figs. 1(a) and 1(b) and may be identified as those of the 8&apos; and <02 structures respectively. The lattice parameter of the ß&apos; phase was determined as 3.1566Å.* This value compares very well withthatto be expected for a 50 at. pct Zn alloy from the data of Owen and Edmunds? and indicates that no loss of Zn occurred during casting. In order to study the effect of cold work upon the ß&apos; and o phases, filings made at room temperature and sieved through 230 mesh were mounted immediately in the diffractometer-i.e., without a strain-relief anneal. Changes in structure on subsequent aging were followed by scanning repeatedly over the regions of the low index reflections of the ß&apos; and o structures-i.e. , 28 from 35 to 44 deg. Immediately after filing the 8&apos; specimen, additional diffraction peaks were observed in the low-index region of the pattern, as shown in Fig. 1(c). These additional peaks do not coincide with those of the o structure, Fig. l(b), but may be indexed as the (10.0), (00.2), and (10.1) reflections of an hcp phase (<) with nearly ideal axial ratio. However, this hexagonal phase appears to be very unstable since within a very short time at room temperature it reverts back to the ordered ß&apos; phase, the reversion being complete within seven hours. The 5 ? ß&apos; reversion reaction is, therefore, very similar to those already reported in Cu-Zn5 and Ag-Cd6 7&apos;alloys. The action of filing caused the deformed surface of the originally pink ingot to become silver in color, indi-cating that the ( phase possesses similar reflecting properties to the o phase. Hence, the subsequent

Jan 1, 1962