Search Documents

By Gearge C. Wallick

This paper describes experimental procedures for the calibration of capillary tubes to be employed as comparison standards in gas flow-rate measurements and considers several types of flow which were observed in the calibration of seven capillaries of varying diameter. It is shown that under certain experimental conditions deviations from Poiseuille flow are observed which may not be attributed to turbulence, and that this flow behavior may be described empirically by introducing the classical kinetic energy correction into the Poiseuille equation. INTRODUCTION Techniques have been developed for the measurement of the volume rate of flow of nitrogen through glass capillary tubes as a function both of the differential pressure applied and of the absolute gas pressure. Capillary tubes thus calibrated are frequently used to determine the rate of gas flow through a porous sample in the measurement of slip-corrected permeability. The purpose of this note is to describe the calibration procedure and to discuss some observed deviations from the ideal flow behavior predicted by the Poiseuille equation. EXPERIMENTAL PROCEDURE The volume flow rate of nitrogen as a function of the differential pressure was determined experimentally for a series of seven glass capillary tubes of varying diameter. As is shown in Table 1, the capillary radii in the series ranged from 0.004 cm for K1 to 0.07 cm for K7. The capillary tubes were cut from capillary tubing purchased on special order from several manufacturers and the bore radii were determined by microscopic measurement. The gas volume flow rate was measured for each capillary tube at a series of differential pressures in the range from 0 to 3 cm of mercury and at average absolute pressures of 1.0, 2.5, 4.0, and 6.0 atm. Experimental Procedure for Small Capillaries A schematic diagram of the apparatus used to calibrate the three smallest capillaries, Kl, K2, and K3, is shown in Fig. 1. By means of a standard Ruska Instrument Corp. volumetric pump (equipped with a synchronous motor drive, two stages of gear reduction, and a quick-change lathe gear box), nitrogen was displaced by mercury from a metal cell immersed in a constant-temperature bath. The pump, the line to the cell, and a part of the cell were filled with mercury. As mercury was forced into the cell, it displaced nitrogen which passed through the capillary tube being calibrated and into a large container with a volume of approximately 30 liters. Since the volume of this container was very large compared to the total volume change of the gas resulting from the action of the displacement pump, the absolute pressure of the system was essentially constant throughout any one run. Prior to any determination this pressure could be set at any desired level by means of an auxiliary nitrogen cylinder. The differential pressure across the capillary was measured with a Meriam Red Oil manometer and recorded together with the corresponding pump displacement rate which was equal to the gas flow rate. By repeating this process for a series of different displacement rates at each of the absolute pressures of interest, the data necessary for plotting the calibration curves for capillaries K1, K2, and K3 were obtained. All calibration measurements were made in a constant temperature room to minimize errors due to temperature fluctuations. In each run. the flow was maintained until equilibrium was established. Experimental Procedures for Large Capillaries The flow rates through Capillaries K4, K5, K6, and K7 required to obtain the pressure drops desired were larger than could be obtained from available constant displacement pumps, and it was thus necessary to employ an alternative calibration procedure. The arrangement of apparatus used in calibrating these capillaries at an average pressure of one atmosphere is shown in Fig. 2. Each capillary was calibrated by flowing nitrogen through the capillary and recording the differential pressure as a function of the flow rate. 'The differential pressure was measured with a Meriam Red Oil manometer and the flow rate was determined by collecting the effluent gas over water at constant pressure and recording the increase in volume per unit time after an equilibrium had been established. Appropriate corrections were made for the

Jan 1, 1953

By William L. Boyd, Eugene L. McCarthy, Laurance S. Reid

Proper control of the moisture content of natural gas is essential to reliable operation of gas transmission and distribution facilities serving northern markets. The moisture content of natural gas is usually determined by dew point measurement at the existing pressure. For any gas of constant moistrire content. the dew Point varies with the pressure. A correlation of the data of several investigators is prezented in graphical form by the authors. These data were correlated by the authors and F. M. Townsend, C. C. Tsao. M. I). Rogers. Jr.. and J. A. Porter. graduate students in chemi(.a1 engineering at the University of Oklahoma. Of articular interest are the hitherto unpublished low temperature data observed by Wickliffe Skinner. Jr., which are included in this correlation. PRESENTATION OF DATA The problem of interpreting water dew points, or saturation temperatures. of natural gas in terms of specific moisture con-tent has increased in importance during the past decade bec.arl.;e of extensive development.; in the transmission and petro-chemical phases of the natural gas industry. Virtually all gas transported to northern and eastern markets must be dehydrated to a low water vapor content to prevent hydrate formation in transmission and distribution lines and resultant interruption.; in gas deliveries. Complete dehydration is required in certain phases of tile petro-chemical industry involving low-temperature operations. It is a well-known fact that the water vapor content of pure hydrocarbon vapors and their mixtures at superatmospheric pressures cannot be predicted with accuracy by assuming validity of the ideal gas laws." Earlier interest in the general problem was concentrated on the water vapor content of pure hydrocarhons and hydrocarbon mixtures in the pressure and temperature ranges common to gas and oil producing reservoirs in order to obtain fundamental data for the improvement of production techniques and the furtherance of reservoir studies. Excellent data are published for pressures ranging from atmospheric to 10,000 psig and for temperatures ranging from 100° to 460° F4,9,10,11 and are found to be in close agreement. However, experimental data at high pressures and temperatures below 100°F are comparatively limited in scope. Experimental data in the lower temperature range have been reported by Laulhere and Briscoe.8 Deaton, et al,2,3 Hammerscllmidt,5,6 and wade," In general, the pressures employed in these investigations ranged from atmospheric to 1.000 psig while temperatures ranged from 32° to 120°F; i.e., the usual conditions encountered in gas transmission line operations, Additional data were reported by Russell, et al,12 at pressures as high as 2.000 psig and covering a rather narrow atmospheric temperature range. In 1947, Hammerschmidt published a correlation of all available data,' in which the water vapor content of gases at saturation. under high pressure and low temperature. was predicted by extrapolation. In 1948, Wickliffe Skinner. Jr.. presented data on the moisture content of a low nitrogen content gas at low temperature and at pressures ranging upward to 1.500 psia.1-3 Comparison of Skinner's experimental data with the extrapolated data of Hammerscllmidt revealed an appreciable variation in the lower temperature range. emphasizing the need for a new correlation which would rely on Skinner's data at lower temperatures. Careful scrutiny of available data suggested that presence of an appreciable quantity of nitrogen in a gas mixture may affect its saturated moisture content so that data obtained from gases with more than three per cent nitrogen were not used in this correlation. CORRELATION OF DATA Data employed in this correlation are presented in Table I. The data of Dodson and Standing.4 McKetta and Katz,9 and Olds, Sage and Lacey10 were compared and found to be in close agreement so that the data of Olds. et al, re-plotted in a more convenient form by the Humble Oil and Refining Co.,' were used for temperatures of 100°F and above. Skinner's data were used for temperatures below 40°F. Between these intermediate temperature limits, the data of Hammerschmidt.7 Wade" and extrapolated data of Olds. et al.1 were tabulated

Jan 1, 1950

By N. J. Grant, R. Nordheim

An extensive study was made of the aging characteristics of alloys based on the 80 pct Ni-20 pct Cr composition hardened with aluminum and/or titanium, each up to 4 pct. Aging was followed by means of hardness and hot electrical resistance measurements as well as by X-ray and microscopy. Stress rupture tests at 1500°F were utilized as a check on the predicted behavior. THE titanium and aluminum hardened Ni-Cr alloys, exemplified by Nimonic 80 and Inconel X, constitute one of the more important groups of alloys developed to meet the demand for materials retaining their strength at elevated temperatures. For service in the temperature range 1200" to 1500°F, these alloys offer high creep resistance. With increasing service temperature, however, the strength of the simpler Ni-Cr base alloys falls off rapidly so that above 1500°F there is a significant loss of strength. The present investigation was undertaken with the hope that a better understanding of the factors controlling the precipitation hardening of these alloys would make it possible to increase the useful service temperature range. Primarily this investigation involved the study of the effects of titanium and aluminum on the hardening and the subsequent softening at elevated temperatures. The titanium and aluminum contents were each varied between 0 and 4 pct by weight at a constant nickel to chromium weight ratio of about 4:1. (Except when otherwise stated, all compositions are expressed on a weight basis.) The major part of the investigation was confined to alloys with less than 0.06 pct C. Recently several papers dealing with the identity of the microconstituents in the titanium and aluminum hardened Ni-Cr alloys have been published. Using X-ray analysis of the residues from anodic dissolution, Rosenbauml was only able to identify carbides and nitrides in Nimonic 80 and Inconel X. However, since Rosenbaum worked with alloys in the hot rolled rather than in the aged condition, his results are inconclusive. Recently Hignett' reported that the hardening of Nimonic 80 was due to the controlled precipitation of Ni,(TiAl) having the cubic Ni3A1 structure. Taylor and Floydv-" published the results of an investigation of the nickel-rich corner of the Ni-Cr-Ti, Ni-Cr-Al, and Ni-Ti-A1 systems. In the Ni-Ti and the Ni-A1 systems the hexagonal Ni,Ti phase, 7, and the cubic Ni3A1 phase, -y', respectively, exist in equilibrium with the nickel-rich solid solution. The interatomic distances in the basal plane of Ni,Ti and the octahedral planes of the matrix are almost equal, thus explaining the Wid-manstaetten type structure formed when Ni,Ti precipitates from solid solution. When Ni:,Al precipitates from solid solution, it appears usually in globular form, often dispersed along rows corresponding to definite crystallographic directions. The 7 and phases are also the only intermetallic compounds which occur in the nickel ternary alloys with up to 25 pct Cr and 10 pct Ti or Al. Taylor and Floyd found that Ni,Ti takes practically no nickel, chromium, or aluminum into solution. Nial, on the other hand, dissolves a considerable amount of chromium and titanium and some nickel. Up to three out of every five aluminum atoms could be replaced by titanium in Ni,Al. This substitution caused a slight increase (less than 1 pct) in the lattice parameter. With respect to the effect of variation in the titanium and aluminum contents on the high temperature strength of Nimonic 80 type alloys, Pfeil, Allen, and Conway" reported that an 80 pct Ni-20 pct Cr alloy containing 0.20 to 0.30 pct A1 had the highest creep resistance when the titanium content was kept between 1.65 and 2.75 pct. Experimental Procedure The materials used for this investigation were electrolytic nickel, electrolytic or low carbon chromium, sponge titanium and 2s aluminum. The alloys were melted in an indirect carbon arc furnace under

Jan 1, 1955

By R. G. Garlick, H. B. Probst

Tungsten single-crystal specimens of various orientations were deformed in tension at room temperature. Slip traces indicated both (112)(111) and (110) (111) slip; however, about 10 pct plastic dejormation was required bejore these traces could he seen. Resolzled shear-stress considerations indicated that at least some of the particular systems observed were not those on which slip initiated hut were secondary systems. This is highly probable, considering the high plastic strains involved. Analysis of the stress data with respect to possible slip systems indicated that slip must have been initiated at stresses below the proportional-limit stresses measured. ALTHOUGH there is general agreement that slip deformation in fcc and hep metals takes place on the plane of close packing and in the direction of close packing, there is no such agreement for slip in bcc metals. It is generally agreed that the close-packed direction (111) is the slip direction, but investigations have led to conflicting descriptions of the slip plane. As Hoke and Maddin1 point out, there are essentially four points of view. 1) Deformation in bcc metals is composite shear on (112) and (110) planes or on nonparallel (110) planes, and any apparent slip on other planes can be accounted for completely by slip on these planes. Chen and Maddin have reported this to be the possible case for molybdenum." 2) Slip occurs in the (111) direction and is limited to {110), {112), and (123) planes (the three closest packed planes of the lattice). 3) Slip occurs in a (111) direction, but not necessarily on planes of close packing (banal slip). 4) Slip occurs in those directions and on those planes for which ß, the ratio of Burgers vector to interplanar spacing, is a minimum. The slip systems of the bcc metal tungsten have never been fully determined, although several investigators have reported pertinent results.3"7 The present work was initiated to determine the active slip systems in tungsten at room temperature, the critical resolved shear stresses associ- ated with these systems, and the orientation dependency of operative systems. These features of tungsten deformation at room temperature have never been reported in the literature. The authors find this somewhat surprising, particularly in view of the availability of tungsten single crystals since the advent of electron-beam zone-melting techniques and the widespread interest in refractory metals. It would seem apparent that such work has been attempted but the results have not been reported, possibly due to the conflict with deformation theory. The results of the present work conflict with any straightforward description of deformation based on the proposed explanations of slip in bcc metals. Although these conflicts have not been resolved, a presentation of the problem seems in order and should be of value to others working in this field. MATERIALS AND PROCEDURE Single-crystal tungsten rods of 1/8-in. diameter were grown from undoped commercial rod by one-pass electron-beam zone melting in apparatus previously described by witzke.8 Representative analyses of the rod before and after melting are given in Table I. There was no detectable zoning of impurities during melting. Buttonhead tensile specimens, as shown in Fig. 1, were machined from single crystals. Two flats 90 deg apart were ground in the gage length of each specimen. These flat surfaces facilitated the analysis of slip traces. No attempt was made to position these flats with respect to the crystal orientation. The worked surface layer of the machined specimens was removed by electrolytic polishing in a NaOH solution. Tensile-axis orientations were determined by standard Laue back-reflection techniques. The sharpness of the Laue spots indicated that the crystals were free of strain.

Jan 1, 1964

By J. R. Jargon, H. K. van Poollen

Non-Newtonian fluids may be injected into a reservoir during secondary recovery operations. The non-Newtonian fluid used in this work is a power-law type of fluid that is, the viscosity of the fluid decreases as the flow rate or rate of shear increases. This paper presents equations for steady-state linear and radial flow of such fluids, transient behavior results from a finite difference model of a radial system, and transient behavior results from a field test. The equations that describe the flow of a non-Newtonian fluid are non-linear and are solved numerically. Finite difference solutions are presented as curves of dimensionless pressure drop at the wellbore us dimensionless time for a constant injection rate. Solutions were obtained for 5-percent, 10-percent and 100-percent PV of a non-Newtonian fluid for injection rates of 1, 10, 100 and 1000 cc/sec and for a 5 percent PV of non-Newtonian fluid located at T = Tw' 3, 10, 20, 50 and 100 ft for a flow rate of 1 cc/sec. The buildup curves do not exhibit a stmight-line portion as is the case for Newtonian flow through porous media. Correlations also are shown for the productivity index vs rate for the computer model study and the field tests. INTRODUCTION During various secondary recovery operations non-Newtonian fluids are injected. Such fluids, in general, include thickened water and gelled fluids. The term "non-Newtonian" implies that the viscosity is not only dependent upon temperature and pressure, but also on the rate of shear that is applied to the fluid. For example, water, which is a Newtonian fluid, will have essentially the same viscosity no matter what rate of shear is applied. A pseudo-plastic fluid exhibits a decreasing viscosity when higher rates of shear are applied; a dilated fluid has an increasing viscosity with increasing rates of shear. The objective of studies performed and described in this report is to obtain relationships and mathematical and empirical descriptions of the flow of non-Newtonian fluids through porous media. Simple mathematical relationships, computer studies that include the unsteady-state behavior of such fluids, and field tests are used. PREVIOUS LABORATORY STUDIES Laboratory studies have been performed by several investigators. The fluids used in one investigationl were surfactant-stabilized dispersions of water in hydrocarbons. Its Fig. 6 is reproduced as our Fig. 1. This effective-viscosity vs frontal-velocity diagram shows that this fluid is of the power-law type over a fairly large range of frontal velocities. Gogartyl developed an equation for the effective viscosity as a function of shear rate that reduces to Eq. 2 for frontal velocities greater than about 2 ft/D. The fluid characteristics used in the present study are similar to those reported by Gogarty. Christopher and Middleman2 performed experiments with power-law fluids flowing through pipes packed with glass beads. They used a modified Blake-Koteny

Jan 1, 1970

By L. L. McMurray

ILMENITE is the most important raw material for manufacture of titanium dioxide.1 Industrially, several other products are made from ilmenite, the most important of which are: ferrotitanium, ferro carbon-titanium, copper-titanium, titanium carbide and titanium nitride. The production of titanium metal is still in the laboratory stage because of the difficulty of extraction and as yet no important application for the metal has been found. Ilmenite has received considerable attention as an industrial raw material. Imports of ilmenite concentrates for the first nine months of 1941 were 156,737 short tons, the chief source being Travancore, India.2 Domestic production of ilmenite has here-tofore been confined to Amherst and Nelson Counties, Virginia, where a complex rutile, ilmenite, and apatite ore is mined and treated to utilize all three of these minerals. A recent report3 has described development of the large titaniferous magnetite ore body at Tahawas, New York, where it is expected that 800 tons of ilmenite concentrates, containing 48 per cent Ti02 will be produced daily. Additional domestic production is expected from a large ilmenite deposit recently opened in Caldwell County, North Carolina. Flotation tests indicate that a high-grade concentrate containing 53 per cent Ti02 can be made from the North Carolina ore. Prospecting of domestic ores in other areas has been reported.4 It appears that increased domestic production of ilmenite may well save considerable shipping space so vitally needed in these times. The composition and chemical structure of pure ilmenite is given by Dana as: FeO, TiO2; Ti, 31.6 per cent, Fe, 36.8 per cent, 02, 31.6 per cent. This composition is variable in that some iron or titanium may be replaced, giving a variable iron-titanium ratio. As an example, the iron-titanium weight ratio of ilmenite in Caldwell County, North Carolina, has been determined to be 0.94 (using 97.1 per cent ilmenite concentrate obtained by heavy liquids on minus 150-mesh ore) compared with theoretical 1.16. No rutile was noted in this ore to account for the low value. This North Carolina ore is free of magnetite, which is a common associate of ilmenite ores. In view of a large potential production from North Carolina, the Tennessee Valley Authority conducted a study of methods of concentration of that ore, of which the results are reported herein. THE ORE Five samples of ore were taken from the deposit at various exposed locations and were mixed for the study and testing. An attempt was made to proportion the amount of weathered and unweathered portions in making the composite sample, so as to approximate actual operating conditions. An examination of representative specimens of the sample showed the following general facts: I. The black mineral comprising nearly 70 per cent of the ore is ilmenite.

Jan 1, 1944

By L. L. McMurray

Ilmenite is the most important raw material for manufacture of titanium dioxide.' Industrially, several other products are made from ilmenite, the most important of which are: ferro titanium, ferro carbon-titanium, copper-titanium, titanium carbide and titanium nitride. The production of titanium metal is still in the laboratory stage because of the difficulty of extraction and as yet no important application for the metal has been found. Ilmenite has received considerable attention as an industrial raw material. Imports of ilmenite concentrates for the first nine months of 1941 were 156,737 short tons, the chief source being Travancore, India.2 Domestic produttion of ilmenite has heretofore been confined to Amherst and Nelson Counties, Virginia, where a complex rutile, ilmenite, and apatite ore is mined and treated to utilize all three of these minerals. A recent report3 has described development of the large titaniferous magnetite ore body at Tahawas, New York, where it is expected that 800 tons of ilmenite concentrates, containing 48 per cent TiO2 will be produced daily. Additional domestic production is expected from a large ilmenite deposit recently opened in caldwell county, North carolina. Flotation tests indicate that a high-grade concentrate containing 53 per cent TiO2 can be made from the North Carolina ore. Prospecting of domestic ores in other areas has been reported.' It appears that increased domestic production of ilmenite may well save considerable shipping space so vitally needed in these times. The composition and chemical structure of pure ilmenite is given by Dana as: FeO, TiO2; Ti, 31.6 per cent, Fe, 36.8 per cent, O2, 31.6 per cent. This composition is variable in that some iron or titanium may be replaced, giving a variable iron-titanium ratio. As an example, the iron-titanium weight ratio of ilmenite in Caldwell County, North Carolina, has been determined to be 0.94 (using 97.1 per cent ilmenite concentrate obtained by heavy liquids on minus Iso-mesh ore) compared with theoretical 1.16. No rutile was noted in this ore to account for the low value. This North Carolina ore is free of magnetite, which is a common associate of ilmenite ores. In view of a large potential production from North Carolina, the Tennessee Valley Authority conducted a study of methods of concentration of that ore, of which the results are reported herein. The Ore Five samples of Ore were taken from the deposit at various exposed locations and were mixed for the study and testing. An attempt was made to proportion the amount of weathered and unweathered portions in making the composite sample, so as to approximate actual operating conditions. An examination of representative specimens of the sample showed the following general facts: 1. The black mineral comprising nearly 70 per cent of the ore is ilmenite.

Jan 1, 1948

By L. L. McMurray

Ilmenite is the most important raw material for manufacture of titanium dioxide.' Industrially, several other products are made from ilmenite, the most important of which are: ferro titanium, ferro carbon-titanium, copper-titanium, titanium carbide and titanium nitride. The production of titanium metal is still in the laboratory stage because of the difficulty of extraction and as yet no important application for the metal has been found. Ilmenite has received considerable attention as an industrial raw material. Imports of ilmenite concentrates for the first nine months of 1941 were 156,737 short tons, the chief source being Travancore, India.2 Domestic produttion of ilmenite has heretofore been confined to Amherst and Nelson Counties, Virginia, where a complex rutile, ilmenite, and apatite ore is mined and treated to utilize all three of these minerals. A recent report3 has described development of the large titaniferous magnetite ore body at Tahawas, New York, where it is expected that 800 tons of ilmenite concentrates, containing 48 per cent TiO2 will be produced daily. Additional domestic production is expected from a large ilmenite deposit recently opened in caldwell county, North carolina. Flotation tests indicate that a high-grade concentrate containing 53 per cent TiO2 can be made from the North Carolina ore. Prospecting of domestic ores in other areas has been reported.' It appears that increased domestic production of ilmenite may well save considerable shipping space so vitally needed in these times. The composition and chemical structure of pure ilmenite is given by Dana as: FeO, TiO2; Ti, 31.6 per cent, Fe, 36.8 per cent, O2, 31.6 per cent. This composition is variable in that some iron or titanium may be replaced, giving a variable iron-titanium ratio. As an example, the iron-titanium weight ratio of ilmenite in Caldwell County, North Carolina, has been determined to be 0.94 (using 97.1 per cent ilmenite concentrate obtained by heavy liquids on minus Iso-mesh ore) compared with theoretical 1.16. No rutile was noted in this ore to account for the low value. This North Carolina ore is free of magnetite, which is a common associate of ilmenite ores. In view of a large potential production from North Carolina, the Tennessee Valley Authority conducted a study of methods of concentration of that ore, of which the results are reported herein. The Ore Five samples of Ore were taken from the deposit at various exposed locations and were mixed for the study and testing. An attempt was made to proportion the amount of weathered and unweathered portions in making the composite sample, so as to approximate actual operating conditions. An examination of representative specimens of the sample showed the following general facts: 1. The black mineral comprising nearly 70 per cent of the ore is ilmenite.

Jan 1, 1948

Molybdenum was first discovered on the Continental Divide in Colorado in 19 11; and in 1918 two companies, one of which was the Climax Molybdenum 250 stpd operation, were producing. In 1919 both mines were shut down, but in 1924 the Climax mine reopened and has been producing ever since. Over the years mine production has been increased until today the mill capacity is 48,000 stpd (43,500 mtpd). From 1935 to 1973 all ore was mined underground by block caving with scraper slushing. Since 1973 ore production has been supplemented by open pit mining. As demand for molybdenum increased, upper levels of the mine became worked-out and new lower levels were opened. In late 1972 production began on the 600 level with the mined ore being primary and secondary crushed in the new No. 4 crushing station. Ore is hauled to the primary in 10 st (9. 1 mt) capacity Granby side-dump cars. The trains, carrying 200 st (181 mt), pass throug.h a dump block and discharge directly into a 54 in. by 84 in. Traylor TC gyratory crusher set at an 8 in. (203 mm) open side setting. Since the ore has already been broken to a size which will pass the finger raises in the mining areas, there are only rare oversize boulders to block the crusher opening. Selection of the crusher was based more on its capacity than its receiving opening, as is often the case with gyratories used in open pit operations. Nominal and maximum capacities for this unit are 1250 and 1800 stph (1 135 and 1635 mtph). The ore is often wet and sticky, so a mechanical car cleaning device is utilized. Under the crusher is a 300 st (270 mt) ore pocket equipped with a 60 in. (1.52 m) wide inclined conveyor which delivers the ore to a 2,000 st (1800 mt) surge bin. Near the head pulley of this conveyor is a wood picking station whe re tramp wood and steel are put into cars for removal. Two more apron feeders remove the primary crushed ore from the surge bin, and impact belts and conveyor belts transport the ore to the crushing station for screening ahead of two 7 ft (2. 13 m) standard crushers. Secondary crushed ore is then conveyed to the surface for tertiary crushing. The entire underground crushing room containing the primary, two secondaries, screens and related equipment is serviced by a 100 st (90 mt) crane with a smaller capacity fast hook. A control room is situated so the operator can observe all the crushing operations. Rotoclone collectors remove dust from the entire operation (including the fumes from the zinc pots) and discharge it to the final product belt. The Rotoclones are vented through drifts and raises to the surface. Shop facilities, electrical gear, and lubrication equipment are located

Jan 1, 1978

The Climax Molybdenum Company' s newest operation is the Henderson project, which is located on the east side of the Continental Divide. Ore reserves are estimated at more than 300 million tons at a grade of 0.49% MoS2. For mining the ore a modified panel caving system is used. The ore is transported to the Henderson mill on the west side of the Continental Divide on a 42 in. (1.07 m) gauge railroad through 9.6 miles (15.4 km) of tunnel and 4. 8 miles (7.7 km) of surface track, a total distance of 14.4 miles (23. 2 km). Each train consists of 30 ore cars with capacity of 22 st (20 mt) of ore or 660 st (599 mt) per train. The unmanned trains operate completely automatically. At the 54 in. by 84 in. primary gyratory crusher, the bottom dump ore cars pass over a dump scroll to discharge at a maximum rate of 100 st (91 mt) per minute. Dumped ore falls onto a rock box before passing over a 17 ft long by 46 ft wide (5. 2 m by 14 m) grizzly set at a 40° angle with bar spacings of 7 ½ and 8 ½ in. (191 mm and 216 mm) openings. An estimated 30 to 50% of the ore (which at times is wet and sticky) passes through the grizzly. The operators report that a shallower angle on the grizzly, perhaps 35º to 37º, would have been sufficient and would have prevented impact on the back of the crusher pocket by large boulders. This pocket as well as the crushed ore pocket under the crusher is lined with AR plate. The accompanying drawings show a "future splitter" and the operators are planning the installation of this unit to prevent impact and subsequent damage to the crusher spider. Crushed ore at an 8 to 9 in. (203 mm to 229 mm) size joins the grizzly undersize in the pocket beneath the crusher. This pocket is sized at 660 live st (599 mt) so that it will accept an entire trainload of ore. Crushed ore is removed from the pocket by a four-speed, 84 in. (2. 1 m) apron feeder operating at 9.6 to 29. 3 fpm (2.9 to 8.9 mpm). A 60 in. (1.5 m) takeaway conveyor operating at 480 fpm (146 mpm) delivers the crushed ore to a 58,000 st live and 193,000 st total (52,600 and 175, 100 mt) open stockpile under an A -frame supported tripper gallery. Impact idlers on the takeaway conveyor under the apron feeder discharge are mounted on wood blocks for a cushioning effect and ripped belt detecting bars are located behind each impact idler. The conveyor tunnel is of corrugated and galvanized steel construction rather than concrete. The concrete crusher enclosure is circular in design from its lowest level at elevation minus 110 ft 4 in. (minus 33. 6 m) to elevation

Jan 1, 1978

By Raymond E. Byler

THE challenge of unprecedented need for more metals to meet present-day re-armament and domestic requirements is being met with minerals beneficiation projects of great number and variety, and with new and improved methods, techniques, and. equipment. Iron Range Developments Much attention has been given during the year to the tremendous program for beneficiation of taconites and intermediate iron ores which is progressing through large pilot-plant tests preparatory to full-scale production operations. The greatest activity has been directed toward concentration of magnetic taconites on the Mesabi Range. The Reserve Mining Co. has let $75 million in construction contracts for the 2 ½ million-ton-per-yr project (concentrates) at Beaver Bay, Minn., and is building a 300,000-ton-per-yr pilot plant to prove up the magnetic separation and pelletizing operations. Oliver Iron Mining Co. has a pilot plant under construction near Mountain Iron for concentrating magnetic taconites, and is operating experimentally a sintering and nodulizing plant on fine ore screenings and concentrates at Virginia to fully develop agglomeration technique. The Erie Mining Co. plant at Aurora continues its production of concentrates from magnetic taconites which was begun three years ago. No plans have been announced to treat the Mesabi Range nonmagnetic taconites, but F. D. Devaney, Pickands Mather and Co., is studying a new process for magnetically roasting lean ores to make them amenable to low-intensity magnetic concentration. W. R. Van Slyke, Cleveland-Cliffs Iron Co., calls attention to several noteworthy developments in the field of intermediate ores, perhaps the most significant of which has been the first commercial operation of a Dutch State Mines (DSM) cyclone plant at the Buckeye mine of the M. A. Hanna Co. The plant concentrates the +1/4 in. fraction by means of conventional heavy-media treatment after suitable crushing, screening, and washing. The -1/4 in. +65 mesh material is treated in two 12-in. cyclones, the -65 mesh fraction being sent to tailing storage. The plant is operating successfully on feed rates up to 120 tons per hr, and indicates that successful treatment of the fine fractions of Mesabi intermediate ores is imminent. Another commercial-size DSM plant was placed in operation late in the year by Cleveland-Cliffs at the Holman mine, and two additional ones are expected to be in operation next year. Various other methods are also in use at different plants for treatment of the fine fractions, including classification, abrasion milling followed by classification, jigging, and Humphrey spirals. Where it can be economically justified, it seems at present that heavy-media treatment of the -1/4 in. fine fraction will also come into increasing use on the intermediate ores. During 1951 a one-unit, heavy-media plant to treat hematitic crude ore was erected at the Ohio mine on the Marquette Range by Cleveland-Cliffs and plans for another plant at Humboldt to produce 2000 tons of concentrates annually is contemplated, as is also the construction of a plant for agglomera-

Jan 1, 1952

By George L. Montgomery

In a recent article Heckler, Elias, and woods1 have described an automatic computer technique for plotting of pole figures. To anyone who has constructed pole figures manually from raw X-ray data, the development of computer plotting techniques has been a very welcome development. The purpose of the present note is to describe an alternative computer plotting method which, if somewhat less precise than the method described by Heckler et al., has the advantages of being faster and of not requiring the availability of a plotter. The plot is made directly by the printer of the terminal system and, by its nature, has a good deal of visual impact. Each character of output symbolizes a level of intensity. For example the numerals 1 to 9 might represent intensities referred to some reference obtained from a randomly oriented sample. Should more levels be required (this is seldom necessary) alphabetic or other characters may be used in addition. When these are arranged in the proper fashion, the result is a pole figure such as is shown in Fig. 1. It is the purpose of the computer program to transform the data and carry out the arrangement in a suitable manner. The computation is carried out on a line by line basis in order to reduce the amount of storage required and thus keep the program "small". It is, thereby, well within the limitations of the time-sharing systems which are becoming increasingly available. The inaccuracies introduced are slight and the plot can easily be made as precise as the technique used to collect the data. Comparison of pole figures produced by this method with those constructed manually shows a high degree of equivalence. To the present, the technique has been applied to reflected X-ray data only. X-ray data are collected in a manner identical to that described by Heckler et al. That is, as the goniometer rotates the specimen, a series of counts, accumulated over a preset time, is recorded. The method by which the proper symbol, representing an intensity level, is assigned to each print position is up to the ingenuity of the programmer. Perhaps the simplest method is to section the stereograph in the fashion of a polar net, and to assign all print positions lying within each segment a symbol representing the level of intensity recorded at the data point nearest to the center of the segment, see Fig. 2. The number and arrangement of the segments are selected to conform more or less with the number of accumulated counts and the geometry of the goniometer path used to collect them. Since the angular distance between accumulated counts is usually not infinitely controllable, it is impossible to locate one reading within each segment and, at the same time, maintain symmetry in the sectioning of the stereograph. This latter requirement is essential to keep the computer program simple and flexible. As an expedient it was found that the number of data points could be increased to conform with the number of segments, with very little loss of

Jan 1, 1969

By M. J. Ginsberg, N. A. Gokcen

THE preliminary study of electrochemical desul-furization performed by Ohtani and Gokcen1 left a number of points concerning the process to be investigated. Two of these were i) the determination of the effect of greater current and voltage on the desulfurizing Flower of acid slags (% CaO/% SiO2- 1) and ii) the possibility of the loss of silica in slag by the reactions 2C (in metal) + SiO2 (slag) = Si (in metal) + 2CO(g) and C + SiO2 (in slag) = SiO(g) + cO(g) proceeding to a point at which the composition of the slag was sufficiently altered toward the basic side so a1.s to noticeably affect the rate of de-sulfurization. The apparatus and the procedure used in the present investigation were the same as those used by Ohtani and Gokcen, except the control circuit was connected to 120 v dc instead of 24 v dc and thereby allowed greater freedom in choosing the values of both current and voltage. The graphite crucible containing the melt and serving as the cathode was 3-in. high, and was of 1 1/2-in. ID with a graphite bar of 3/8-in. diam and 8-in. length threaded into the bottom for electrical connection. This was placed into a magnesja outer crucible with a hole in the bottom and alumina insulation was packed between the two crucibles. A charge consisting of 180 g of

Jan 1, 1962

By N. A. D. Parlee, I. D. Shah

THIS communication reports the results of some work done on the effect of gold, palladium, and platinum on the liquid-gas-solid equilibrium in the Ag-O system,1,2 see Fig. 1. Recently several investigators3, 4, 5 have reported the effects of gold, palladium, platinum, and copper on the solubility of oxygen in liquid silver. This communication represents only a portion of the work done here on the solubility of oxygen in liquid silver and liquid Ag-Au, Ag-Pd, and Ag-Pt alloyss—the greater part having already been reprted. The apparatus, materials, and procedures used were similar to those of earlier work.' l The main precautions observed in obtaining these freezing points at constant temperature and PO2 = 1 atm were as follows: 1) The points were approached very slowly from higher temperatures. 2) In the very near vicinity of the L-G-S equilibrium point precautions were taken to see that the melt was in equilibrium with oxygen at one atm. Equilibrium was considered to have been attained when no more absorption of oxygen was observed in the last 15 min at a fixed temperature. 3) In the case of these alloys, the freezing point of the melt at 1 atm of oxygen and the equilibrium amount of oxygen absorbed by the liquid "infinitesimally" above this point were determined by lowering the temperature in very, very small steps, equilibrating at

Jan 1, 1969

By John A. Garcia

A standard set of coal mining laws for the entire United States is hardly practicsble, yet the numerous variations in the state laws for almost every item seems entirely unnecessary. The same useless variations appear in almost every comparable section with no apparent reason except that no attempt has ever been made to codify them, and as they were developed over a long period of time by innumerable individuals and legislatures, the present situation is the logical outcome of lack of cooperation between states. The ventilation of a mine is affected indirectly by many provisions not listed specifically under this heading, so that it would be necessary to tabulate the major portion of all the laws to secure a complete comparable digest; therefore only a few of the more important have been set down here. This point is well illustrated in the section providing for clearance between car and rib, which is intended as a safety measure against personal injury, but is very important from the standpoint of ventilation because of choked airways in mines on two-entry system. Confusing Phraseology Misinterpretation and confusion may be expected from the phraseology alone; one state provides that the scale of the mine map shall be "not more than 100 ft. to 1 in.;'' another state demands "not less than 100 ft. to 1 in." Both probably mean the same thing and seek to prevent the operator from furnishing a map on which the workings will appear SO small that the detail is illegible. Legislation is certainly indefinite that specifies structures must be fireproof when "near" a mine opening, and just what is a "dusty" or "gaseous" mine is open to argument in most of the states. The variation in spacing crosscuts and break-throughs and the limited number of men on a split seem entirely unnecessary, as the distance is not reduced in gaseous fields, excepting in Arkansas and Tennessee, which states produce a comparatively small amount of coal, and the number of men differs 100 per cent. and more for no apparent reason.

Jan 1, 1927

By Walter S. Weeks, Vitaly S. Grishkevich

Considerable difference of opinion seems to exist as to whether the rate of air flow when a fan is placed on a given duct should be determined by the use of static pressure or total pressure characteristics. A little study will show that both methods are correct. Assume that a fan is connected to a duct by an expansion piece as shown in Fig. 1, and that steady flow is established. Considering the atmospheric pressure as zero pressure, let the static head at the outlet of the fan be h and the velocity at this point be vl. The total head at the outlet is then h + „"• The total head at this point must be equal to the total head at the end of the duct plus the losses that have occurred between the two points. Left be the friction loss in the straight duct, s the shock loss in the dif- fuser, and v2 the velocity at the end of the duct. Then ig. 1.—Fan on duct. A curve showing the value of the left-hand side of the equation for different rates of flow is the total pressure characteristic of the fan, while a curve showing the value of the right-hand side is the total pressure characteristic of the duct. If these two curves are plotted on the same chart, the intersection indicates the rate of flow when steady flow is established. We may look at this problem in another way. The static pressure at the outlet of the fan is the static pressure of the fan and it is also the static resistance of the duct from that point to the end. The friction in the straight duct is f. If the duct were the same area as the fan outlet, would be the static resistance of the whole duct system. In the present case, however, this resistance is decreased by the change of velocity head into static head in the expansion piece. If conversion were perfect, the static pressure recovered would be

Jan 1, 1931

By Charles Legrand

The power plant of the Burro Mountain Copper Co. is located near Tyrone, N. M., at 5,950 ft. elevation. It is interesting because it uses the largest stationary Diesel engines in the United States. The general layout of the plant is shown in Figs. 1 and 2. The building is of steel-frame construction with hollow-tile walls and corrugated-iron roof; the floor is concrete and all windows have steel frames, making a fireproof building. The building is made to accommodate one more electric generator unit which is being installed; also two 4,000-cu. ft. air compressors direct-connected to three-cylinder engines with the same size cylinders as the electric units. The power plant consists of two 815-kva., 60-cycle, three-phase, 6,600-volt, 180-r.p.m. generators, direct-connected to five-cylinder, two-cycle Diesel engines; the necessary circulating pumps for cooling water, cooling towers and oil storage tanks. A portion of the power is used in the same building as the generating units to run one of two 200-kw. rotary converters delivering 260-volt direct current, and a 2,500-cu. ft. air compressor, delivering air at 95 lb. pressure, direct-connected to a 400-hp., 6,600-volt, three-phase synchronous motor. The remainder of the power is used to run a 1,500-ton concentrating mill 3 ½ miles from the power house, various hoists, pumps and motors about the mines and the lighting and water-works of the town of Tyrone. The direct current is used for electric traction in the mine, also to run hoists and motors that were installed before the new power plant was built. Due to the large hoists that take starting peaks of 250 kw. and the 10-ton electric locomotive that takes at times 150 kw., the load is extremely variable, as shown in. Fig. 3.

Jan 9, 1916

By Kenneth L. Adams

10.3-1. Introduction. Equipment replacement or maintenance is of major concern to every company today. It can be the difference between an efficient and profitable operation or an inefficient and struggling one. Mining equipment, as everyone knows, will not last forever. Some equipment becomes obsolete before it wears out while some may be doing its intended job, yet not economically. It is a major problem for management to make the decision as to whether a piece of equipment should be repaired or replaced. There are numerous approaches to this problem; using formulas, charts, and graphs. These would be very good if all conditions were stable. Since conditions and requirements are constantly changing, an accurate observation cannot be derived from a set formula. A formula does, however, serve as a reminder to include most of the items that should be considered when evaluating old and new equipment. In the field of mining there are several questions which enter into the reasoning that are difficult to put into an equation. Some of these are: 1. Will the present equipment produce the required output of the mine, or an increase if necessary? 2. Are reserves adequate to support the purchase of new equipment? 3. Can the old equipment be repaired to efficiently continue the mining operation? 4. What is the stability of future markets for the product? Depreciation rate, or the write-off life, is a factor that can directly effect decisions on replacement. If the initial life expectancy is too long and the price of equipment is not written off when discarded, then the original investment has not been recovered. If the write-off time is too short, then the equipment is written off before replacement is even considered. In this case, the depreciation accrual is usually used to finance some other phase of the operation. In view of the increasing prices, the amount of depreciation fund is generally too small for much incentive to replace an older unit

Jan 1, 1968

By Herbert Ives

THE incandescent gas mantle is of considerable interest from the standpoint of temperature measurement because it presents a series of apparent contradictions to the established laws of radiation on which are based some of our best methods of temperature determination. One of these contradictions is that the mantle of least brightness (of the commercial thoria-ceria group) is the one having the highest temperature; this, though explicable without any violation of radiation laws, was long a stumbling block to the understanding of the performance of the mantle. Another anomaly is that the energy radiated by the mantle decreases with the rise of temperature, thus apparently invalidating total radiation methods of pyrometry, based on the fourth-power law. The discussion of methods of measuring mantle temperature which follows, is largely taken from an extensive study of the physics of the Welsbach mantle. 1 The incandescent gas mantle consists of a skeleton of refractory oxide of very light weight and open structure, formed by the ignition of a cotton or silk "stocking" previously thoroughly impregnated with salts of certain rare earths. The mantle of commerce is a mixture of approximately 99 parts of thorium oxide with 1 part of cerium oxide. This mixture, discovered largely by accident, gives luminous radiation many times greater than that from either of the constituents taken alone. It is customary to speak of the thoria as the "base" and the ceria as the "colorant," and the commercial mantle represents one of a family in which an oxide of low emissive power is employed as a base, which will assume a high temperature, while a small amount of some other oxide of high visible emissive power is added, which will reduce the temperature of the mantle but little. This is, in general, the most efficient- way, from the standpoint of visible emission, to utilize a substance of high emissive power in the visible spectrum. But it is not necessary. that two substances should be employed to produce a radiator

Jan 9, 1919

Suggestions for Directorial representatives should be submitted by the District Committees between November 1 of the year indicated and the following Annual Meeting District 1 New York Section (Each Year) District 2 Boston (1950) Pennsylvania Anthracite (1951) Lehigh Valley (1952) Philadelphia (1953) Connecticut (1954) Adirondack (1955)

Jan 1, 1952