Search Documents

R. G. BROWN, Bodie, Cal.: Mr. Rickard's paper, with its valuable illustrations, brings into fresh clearness the game of hide-and-seek which the miner must play with his ore-deposit; but, more than this, it goes far towards classifying those perplexing idiosyncrasies which, while unclassified, constitute a labyrinth almost without clue. Probably every engineer can add to the list by the mention of at least one fresh detail from his own experience, and I for one would like to comment on two of Mr. Rickard's divisions. To what he has written about " walls within walls" and " walls without walls," the accompanying Figs. 1 and 2 may be appropriate, the more so as they represent conditions obtaining in a part of the Butte copper-belt more typical of the copper-veins as a whole than the Gagnon, which, in some respects the most interesting mine in the camp, stands almost alone in many particulars. (See nuns., xvi., 62.) Fig. 1 was sketched in January, 1895, in the stopes above the 700-foot level of the Colusa-Parrot mine, east of the Parrot and southwest. of the Anaconda. The stope, the commercial foot-wall of which is shown at A, was 30 feet wide at this section, the pay-ore being massive chalcocite, jumbled with bornite, pyrite, quartz and thoroughly broken-down granite. A and At are inch-thick seams of black talc; B, B' and B" are also talc, possibly 1/8-inch thick. In the plane of the section the "banded quartz " and " quartz and pyrite " were both of too low grade for extraction, but 5 feet back along the stope had been of fair value. The granite with quartz and bornite between Bt and A' was pay-ore, but that to the right of B" was not. In both cases the ferro-magnesian minerals had been removed, leaving, where not obscured by ore, faint, dark patches. Between A'

Jan 1, 1897

By R. H. SWEETSERS

A Discussion of Mr. Hall's paper, read at the Washington Meeting, February, 1905. R. H. SWEETSER, Sault Ste. Marie, Ont. (communication to the Secretary*) :-The recent work of furnace No. 1 of The Algoma Steel Co., at Sault Ste. Marie, Ontario, using for fuel, first all charcoal, then a mixture of charcoal and coke, and finally all coke, upsets the estimates given by Mr. Hall in the last two paragraphs of his interesting paper. Furnace No. 1 was built for a charcoal-furnace, and it was run on charcoal fuel from March 6 until July 9, 1905; then, for a week, a mix¬ture of charcoal and coke was used, and, since then, coke alone has been the only fuel. It is to be regretted that at no time, during the run on charcoal, was there enough charcoal on hand and " in sight'" to warrant blowing the furnace as hard as it should have been blown. During April and May the supply of charcoal limited the amount of blast to about 8,000 cu. ft. of air per min.; in June, to about 8,900 cubic feet. For a few days in July about 10,000 cu. ft. were blown, and then the maximum daily output, 173 tons (2,240 1b.), was reached. At all times the quality of the charcoal was poor, having been made from wood cut from three to four years before. Doubtless this furnace could have produced .200 tons of iron per day, even with this quality of charcoal, provided the supply had been sufficient; and with good charcoal I see no reason why it could not make as much iron per day as it has made with coke. During the one week of using a mixture of charcoal and coke, the changes in quantity of blast and composition of the slag followed each other so closely that no single condition could last long on the furnace. The results were good, and the pig-iron was about the same in quality as that made during the

Jan 1, 1906

By P. W. Rainier

The Chivor emerald field is situated on the eastern slope of the Andes in the Department of Boyach, at an elevation of about 8000 ft. above sea level. It overlooks the Llanos (plains) of the Orinoco and is watered by many streams flowing into the Rio Meta, the Orinoco's largest tributary. The Rio Meta is navigable from the Orinoco to a point within about 50 miles of the Chivor district and may eventually prove to be the reasonable outlet for the future development of this part of the country. The topography of the district is extremely rugged and mountainous (Fig. I), the difference in elevation between two points on a mining claim 1 km. square being sometimes as much as 4000 ft. The ground is covered with dense forest growth and the available timber is suitable and sufficient for mining purposes, but it is becoming gradually depleted by Indian clearings as the country around the mines becomes settled. The many streams combined with the rough topography give good possibilities for hydroelectric power. The center of population nearest to Chivor is Bogoth, the capital of the republic and a city of some 300,000 inhabitants; the distance is two and one-half days' travel. The first stage of the journey from BogotB is accomplished by rail to Choconta, some 4 hr. travel. From Choconth the journey is made in the saddle, one night being spent in Guateque. The latter is a small town and the nearest post office to the mines, being some 10 hr. ride distant. The roads are mere bridle paths, in parts hazardous and almost impassable in the wet season. All supplies brought to the mines, other than those produced locally, are carried by pack mule; mule freight from Choconth costs 3 centavos1 per pound. The climate of the Chivor district is healthful and bracing. The wet season begins in March and concludes in November, the remaining months being dry. The annual precipitation is about 130 in. The temperature throughout the year is nearly constant, varying from about 45" F. to about 65" F. shade temperature. The rains are cold and unpleasant, and for the greater part of each day in the wet season the country is shrouded in dense mist. A fire can with comfort be kept burning in a living room all the year round. There are a few slight

Jan 1, 1931

By J. J. Van Nouhuys

THE economics of aerial survey and the technical processes by the aid of which vertical and oblique aerial photographs are turned into line maps showing the most profuse topographical detail such as contours, rivers, roads, plantations, habitations and cultivated lands do not concern us here. They have been ably and exhaustively described in the publi-cations of the British War Office, handbooks on surveying methods and on photogrammetry and in the South African mining, engineering and geological press. Suffice it to mention that for geological interpretation vertical photo-graphs are used on such scales as soon to 1/5,000 to 1/10,000, overlapping each other by 55 to 60 per cent in the direction of flight and some 10 to 20 per cent sideways on to the next sequence or strip. Through this duplication in the overlap the stereoscopic examination becomes possible. The standards by which monochrome aerial photographs are inter-preted can be grouped under the following headings: 1. Continuity.-The continuity of topographic relief not obtainable on the ground owing to the smallness of man relative to that relief. Here lies the greatest value of aerial survey with relation to geology. An immediate alignment can often be made of drainages running in different directions on each side of a hill; saddles and gorges in the mountainsides; abrupt termination of outcrop or indubitable signs of faulting. Most conclusive evidence is thus often obtained about faults which may be perfectly visible at one place on the ground but cannot elsewhere be identified because of decreased throw. Similarly, dikes can often be followed notwithstanding frequent interruption and disappearance under the soil. Scattered outcrop in scrub-covered or bush-covered country can be conveniently located and often correlated, with a large saving of time compared with field work. The same applies to geological contacts. Once these have been established at a few points on the ground, the intervening stretches can be drawn in.

Jan 1, 1937

By W. A. Roper

Since 1950, several papers have been published which have described various methods for studying mobility ratio effects. The methods which have been described for studying mobility ratio effects include X-ray shadowgraph techniques, stepwise potentiometric model procedures, stepwise numerical procedures, gelatin model studies and fluid mapper model studies. The purpose of this paper is to describe a procedure for using a resistance network for studying mobility effects. DESCRIPTION OF APPARATUS The basic unit of the experimental model consisted of a network of 840 resistors fastened to a sheet of black Lucite which was mounted on a wooden frame, Fig. 1. The dimensions of the Lucite sheet were 36 X 36 in. The resistors were fastened to the Lucite sheet at mesh points by means of snaps. The mesh points were arranged in a square pattern, 30 X 30 in., spaced at intervals of l1/2 in. The snap fasteners permitted several resistors to be "stacked" in parallel. By adding additional resistors to the basic unit, the specific resistance on each side of the flood front could be varied. The square network of resistors represented one of four symmetrical elements of a five-spot well pattern. The current input was analogous to an injection well and the current output was analogous to a production well." The power supply was essentially a full wave transformer-rectifier system for converting alternating-current into direct-current. The DC voltage could be varied from 41.43 to 290 v in steps of 41.43 v by selecting the proper outlet jacks. The major components of the power supply were: a Triro power transformer, R 11-A; a dual 5Y3 vacuum tube; two gas filled OD-3 tubes; and a Triplett voltmeter, model 227-1, range 0 to 500 DC v. The voltages at the mesh points were determined with a Keithley electrometer, model 210, No. 185, manufactured by Keithley Instruments, Cleveland, Ohio. A Heathkit vacuum tube volt-

By W. R. Hibbard

The term lineage was first introduced by Buergerl to denote dendritic branches, grown from a crystal nucleus during solidification from the liquid, with imper- fections in alignment of the order of 10 : to 10-4 cm. These imperfections are associated with distortions of the dendrites caused by the subsequent solidification of the inter-dendritic filling and are illustrated in Fig I. Buerger etched zinc single crystals made by the Bridgman3 method to develop this dendritic pattern and show lineage microscopically. Since maximum crystal growth in face-centered cubic metals occurs along the [IT] directions,2 lineage would appear in copper as small deviations of dendritic branches from these directions. Elam4 and others5"8 reported etching effects resulting from coring along the cube face traces of various copper alloy crystals. These traces were used by Samans8 to orient single crystals. Williamson9 noted a "lined structure (in alpha brass single crystals) consisting of an ordered arrangement of etch pits" which were probably traces of {IOO} planes but somewhat uncertain because they were never straight (that is, apparently lineage). Greningerl1 described the distortion and multiplicity of Laue spots in back reflection X ray photograms of copper single crystals showing lineage. The present investigation -includes metal-lographic, X ray, and property studies of lineage in large grain and single crystal specimens of copper. Preparation of Specimens specilnens 10 in. long 35 1/2 in. diam of oxygen-free copper (o.F.H.c.) (99.985 pet) were' melted vertically in graphite crucibles under an atmosphere of commercial nitrogen purified through a gas train including sulfuric acid, potassium chloride, magnesium chiorate, hot copper chips and phosphorus pentoxide. After a temperature of 1200°C had been maintained for 1/2 hr, the furnace was turned off and the specimens cooled at a rate of about 150°c an hour' This method of direct solidification was used by Greningerlo to produce single crystals with marked lineage and in this investigation produced a fair yield of single crystal specimens in

Jan 1, 1949

By W. R. Hibbard

The term lineage was first introduced by Buergerl to denote dendritic branches, grown from a crystal nucleus during solidification from the liquid, with imper- fections in alignment of the order of 10 : to 10-4 cm. These imperfections are associated with distortions of the dendrites caused by the subsequent solidification of the inter-dendritic filling and are illustrated in Fig I. Buerger etched zinc single crystals made by the Bridgman3 method to develop this dendritic pattern and show lineage microscopically. Since maximum crystal growth in face-centered cubic metals occurs along the [IT] directions,2 lineage would appear in copper as small deviations of dendritic branches from these directions. Elam4 and others5"8 reported etching effects resulting from coring along the cube face traces of various copper alloy crystals. These traces were used by Samans8 to orient single crystals. Williamson9 noted a "lined structure (in alpha brass single crystals) consisting of an ordered arrangement of etch pits" which were probably traces of {IOO} planes but somewhat uncertain because they were never straight (that is, apparently lineage). Greningerl1 described the distortion and multiplicity of Laue spots in back reflection X ray photograms of copper single crystals showing lineage. The present investigation -includes metal-lographic, X ray, and property studies of lineage in large grain and single crystal specimens of copper. Preparation of Specimens specilnens 10 in. long 35 1/2 in. diam of oxygen-free copper (o.F.H.c.) (99.985 pet) were' melted vertically in graphite crucibles under an atmosphere of commercial nitrogen purified through a gas train including sulfuric acid, potassium chloride, magnesium chiorate, hot copper chips and phosphorus pentoxide. After a temperature of 1200°C had been maintained for 1/2 hr, the furnace was turned off and the specimens cooled at a rate of about 150°c an hour' This method of direct solidification was used by Greningerlo to produce single crystals with marked lineage and in this investigation produced a fair yield of single crystal specimens in

Jan 1, 1949

By F. W. Jessen, N. Mungan

The plastic flow characteristics of clay water suspensions were first recognized by Binghaml in 1916 and further studied by Ambrose and Loomis' in 1931-1932. Many physical and chemical properties of clay suspensions are deeply influenced by particle size distribution as well as by the exchange cation. Separation of a number of fractions is particularly helpful in making a detailed study of a suspension. A limited amount of work has been conducted on the effects of particle size on specific properties of mud drilling fluids. A knowledge of particle size distribution is essential for a better understanding of fundamental properties of clay suspensions, particularly viscosity and gel strength. The purpose of this investigation was to study the effect of particle size on the viscosity and gel properties of clay suspensions and to determine any changes in mineral composition accompanying variation in size. EXPERIMENTAL PROCEDURE Numerous methods may be used to fractionate a poly-dispersed clay suspension into nearly mono-dispersed systems. Particles larger than 44 micron (325-mesh) may be obtained by wet screening. For sizes from 44 to 1 micron, the fractionation may be accomplished by sedimentation, elutriation plus microscopy,' or turbidimetry.6 When dealing with systems which contain a major portion of particles below l-mi-cron size, slit ultramicroscopy,7 centrifuge methods of Svedberg,5 eams,9 and McBain,l0 and X-ray methods" may be employed. The Sharples super centrifuge has been proved suitable for the economical separation of suspended particles of submicron range.12,13,14 Three-hundred and forty-five gal of 1 per cent by weight Aquagel suspension was mixed in a high-speed 5-gallon mud mixer and the suspension was allowed to stand in 5-gal glass bottles for 30 days to assure full hydration. All particles larger than 44 microns were removed by wet screening. Five fractions in the range of 44 to 1 micron were obtained by sedimentation. The Sharples super centrifuge method described by Hauser and Reed.13 Norton and Speil,14 Ha user and Lynn,15 and Hauser and Schachman,10 as employed to yield five fractions of submicron size. A super centrifuge operation chart prepared by Fancher, Oliphant, and Houssierre12 was used to determine operating conditions for the desired particle ranges. The clay suspension, after removal of all material above 1-micron size, was centrifuged. During rotation of the bowl, the particles were deposited on a thin plastic liner which fit closely inside the bowl. After passing 5 gal of suspension through the centrifuge, the liner was removed and the particles on the liner were scraped off, remixed and recentrifuged. This was repeated five times. Thus, Fractions H, I, K, and L were obtained. The finest fraction, M, remained in an approximately 0.4 per cent suspension. Water was evaporated under reduced pressure from this suspension to yield the finest particles. Results of the fractionation are included in Table 1. In order to achieve proper orientation and humidity conditions for X-ray diffraction analysis, the following procedure was employed. The dilute suspensions were placed on glass slides and allowed to dry at room temperature. This was repeated several times. Previous to measurement each sample first was placed in a water desiccator for half an hour and then allowed to stand for 15 minutes at room temperature. thus yielding an equilibrium condition of about 52 per cent relative humidity. The relative humidity of the room in which the X-ray diffraction was carried out was maintained at approximately 50 per cent so that there was no change in the spacings during the X-ray examination. Samples

By J. M. W. Mackenzie

The interactions between oil drops and mineral surfaces have been examined for the cetyltrimethylammonium bromide (CTAB)-quartz and sodium dodecyl sulfate (SDS)-hematite systems. The results have been interpreted using a electrical double layer interaction model, a "sweeping-penetration" model based on steric interactions and a free energy of adhesion model. The adsorption of long-chain ions at the mineral interface was also studied and found to follow a Fuerstenau-Modi model of combined Coulombic and chain-chain interaction forces. The basis of the emulsion flotation process and the feature which makes it differ from conventional flotation is: encounter, followed by adhesion, between oil drops and mineral particles which are suspended in an aqueous environment. The manner in which the adhesion between these two phases contributes to the flotation process may be through the formation of min-eral-oil drop-mineral linkages, mineral-oil drop-air bubble linkages, or a combination of both. Possible flotation mechanisms derived from these adhesion processes are shown schematically in Fig. 2 while Fig. 1 shows an example of the first mechanism for quartz particles which have been floated using a cetyltrimethyl-ammonium bromide (CTAB)-Nujol emulsion as collector. In Fig. 2 the three phases, mineral, oil, and air, for convenience have been shown as having approximately equal size. This would not always be the case in an actual emulsion flotation operation. For the flotation of sand-sized particles of approximately 0.5 mm diam, the mineral particles would be at least ten times the size of the largest emulsion drops present in the system, while in the flotation of —10u slime particles, the mineral phase may be of the same order of size as the oil phase. The air bubbles in a flotation cell are normally about 1 to 2 mm in diam and therefore, in general, would be larger than the oil drops. Although the relative size of the three phases does not alter the basic adhesion processes between oil drops, mineral particles, and air bubbles, which depend on the physical and chemical properties of the interfaces involved rather than on the extent of these interfaces, it does alter the degree of deformation of the oil drops and air bubbles which will occur on adhesion. For mechanisms 1 and 2 to take place, the oil-water and mineral-water interfaces must be partially replaced by a mineral-oil interface while in mechanism 2 there is the additional requirement that the oil-water and air-water interfaces must be replaced by an oil-air interface. In view of the importance of the oil drop-mineral particle encounter and subsequent adhesion stages to both of the emulsion flotation mechanisms discussed, a study has been made of some physicochemical factors which control these processes for Nujol-cetytri-methylammonium bromide (CTAB)-quartz and Nujol-sodium dodecyl sulfate (SDS) -hematite systems. Experimental Electrokinetic Measurements.—The zeta potential of mineral particles was measured using a streaming potential technique similar to that described by Fuerste-nau.1 The streaming potential was measured using a multirange electrometer while the plug conductivity was measured using a 50 cycle sec1 bridge. Measurements were made on 28 x 65 mesh particles. Contact Angle Measurements.—A captive bubble technique was used to measure the contact angles for air bubbles and oil drops. The angles were measured on fracture faces of unmounted minerals which proved easier to clean than polished mounted specimens and should more closely represent a flotation system. Reagents: These have been described in a previous publication.0 Minerals: Rock crystal quartz from the New England district, N.S.W., was used for contact angle and streaming potential measurements. The quartz was hand

Jan 1, 1971

By Cyril Smith

A STUDY of the mechanical properties of the alloys of copper and silver led to the discovery that the solubility of silver in copper was greatly different from that generally supposed, therefore some work was done to determine the solubility with greater accuracy than had previously been achieved. After the work had been completed, two papers were published1 giving solubility figures which agreed closely with one another and with the work described herein. A detailed comparison of that work with the present will be given later. PREPARATION OF ALLOYS The copper used in making the alloys was electrolytic ingot of high purity. The silver was prepared by precipitation as chloride from nitric acid solution, followed by fusion of the washed precipitate with sodium carbonate and potassium nitrate. This method gives metal containing at least 99.99 per cent silver. The copper was first melted under charcoal in a small electric resistance furnace and the silver added as pure silver, it being unnecessary to make any intermediate alloys. After thorough stirring the metal was poured into a mold of suitable form. The alloys contained between 0.008 and 0.015 percent of oxygen. Small amounts of oxide were visible under the microscope, but it is not believed this would have much effect on the results. Copper-silver alloys are notorious for segregation, consequently a few experiments were carried out to find a form of casting with as little segregation as possible. A mold 6 in. long and 1/2-in. dia. was first used, and an alloy nominally containing 5 per cent silver was cast in it, while some of the same alloy was poured directly into water to obtain the maximum rate of cooling possible. Analyses were made both on this sample and on turnings from the top and bottom of the 1/2-in. dia. casting, the turnings being separated into three parts according to the position

Jan 1, 1931

By W. H. Bassett

A 10-year, sea-water, corrosion test of tubes of several copper alloys has shown that many alloys withstood attack by solution, pitting, and dezinkification; a 1-year, salt-spray test of sheet-metal specimens of the same composition showed the same results. THE late J. P. Sparrow, chief operating engineer of the New York Edison Co., carried out a series of practical tests on condenser tubes of several copper alloys and reported on the results to the Association of Edison Illuminating Companies at its meeting in' September, 1913. In the preparation of these tubes the senior author had the pleasure of cooperating. Copper-zinc alloys in the proportions of 60-40, 70-30, 80-20, 90-10, and Admiralty metal, which is in effect 70-30 with 1 per cent. of tin, were tried. Monel metal and several copper-nickel alloys, and 8, 5, and 3 per cent. aluminum bronze were also tried. At the time of this report, the aluminum bronze had been in service for 4 1/2 years and seemed to be giving especially good results but later it began to fail and showed no substantial improvement over Admiralty metal. Monel metal was unsatisfactory and the nickel alloys apparently did not give better service than the Admiralty alloy. Previous to the publication of the report, and after considerable discussion, it was agreed that a test where tubes of different kinds could be under laboratory observation would be advisable, so the apparatus described here was set up in The American Brass Co.'s Waterbury Laboratory. This was fitted with tubes of copper, brass, bronze, nickel silver, cupro-nickel and other alloys, and the test started Oct. 11, 1912. Salt water from East River, New York harbor, was barrelled and transported to the laboratory for the test. A fresh supply, completely replacing the water in service, was obtained at the end of each six months period.

Jan 1, 1925

By E. P. Abrahamson

The effect of transition element binary solid solution additions upon the re crystallization temperature of nickel has been investigated. All additions raised the re crystallization temperature. Both the rate of change of re crystallization temperature with at. pet solute and the limit of initial linearity are found to correlate with the free atom ground state outer electron configuration of the solute element. A comparison of all of the correlations for the transition elements studied has yielded a set of empirical relations, which allows the prediction of the effect of dilute binary transition elements on the recrystallization temperature of other transition elements. The work of Abrahamson, et al.1-7 on dilute binary solution alloys indicated a correlation between the free atom ground state electron configuration of the solute and both the brittle-ductile transition and re-crystallization temperature. Further, it has been shown3,4 that the limit of initial linearity may also be correlated with the solute electron configuration. Since previous studies have dealt with bee and hexagonal base elements, this study is made to note what effect, if any, the fee base structure might have. Nickel also serves to give a solvent configuration which will allow the comparison of all of the transition element solvents. Olsen8 has studied the effect of some trace elements upon the recrystallization of nickel. He included only Ti, Zr, W, Mn, and Co of the transition elements. The differences in change of recrystallization temperature were attributed to the solute atom size and to the solubility of the solute in nickel. PROCEDURE All alloys were made using 99.9 + pet Ni with 0.003 C, 0.015 Fe, 0.007 0, and 0.0007 H. The solute elements were 99.9 + pet pure. According to the published binary phase diagrams9 and metallo-graphic examinations at X750, all solute elements were in solid solution. The alloys were arc melted and remelted four times in the form of cubic 200-g buttons under an argon atmosphere. They were then hot forged at 800oC to 0.750 in. diam, machined to 0.60 in., vacuum annealed for 1 hr at 700°c, swaged to 0.40 in. and annealed at 700oC for 1 hr in vacuum. The grain size was checked and found to be 77 * 20 grains per sq mm. The specimens were then swaged to 0.187 in., yielding 76 ± 1 pet cold work. All alloys were then chemically analyzed for the solute addition. The interstitial contents remained at the values of the starting material when checked on random alloy specimens. The swaged rod was cut into 8.25 in. lengths and heat treated in a gradient furnace for 1 hr. The gradient was maintained at 250" to 850°C over an eight inch length, recorded by twelve thermocouples. Control was ± 3oC, accomplished at the hot end. The recrystallization was determined metallo-graphically over the entire specimen. The criterion chosen was that point on the specimen showing the first recrystallized grain at a constant magnification, X200. Specimens were repeated, and the agreement was found to be generally ± 3oC.

Jan 1, 1962

By G. R. M. Del Giudice

The term "slime-coating" is not new in the art of flotation; the phenomenon has been observed and described by Taggart;(l)† Taggart, Taylor, and Ince;(2) and by Ince.(3) Notwithstanding that flotation was introduced for the treatment of finely crushed ore, the adverse effects of slimes have been recognized since the earliest days of the process, and the Elmore, Delprat, Potter, and other processes actually specified desliming of the ore prior to treatment. The cause of this trouble has been studied and described by Taggart;(1) Taggart, Taylor, and Ince;(2) Ince;(3) Morrow and Griswold;(4) and by Gaudin and Malozemoff.(5) Old Theory of Slime-coatings At present, so far as published work shows, there seems to be but one theory for the mechanism of slime-coatings. Ince(3) states that they are due to attraction between electrostatic charges of opposite sign on the sulfide and on the slime particles, supporting this theory by migration experiments in the Burton tube. He also used the microscope in conjunction with a glass cell employed by Beans and Eastlack(6) in studying migration, but met with interference from endosmosis. Several attempts have been made in the Department of Mineral Dressing at Columbia University to duplicate Ince's experiments with the Burton tube, but the results have never been convincing. Formation of precipitates which settled through the pulp levels, and evolution of gas at the electrodes, which disturbed the interface between the pulp and the distilled water above it, seriously interfered with observations. However, by use of the migration cell shown in Fig. 1, endosmosis effects and the disturbances due to precipitation and gas evolution were avoided, and distinct and reproducible migrations or absence of migration were observed. The cell was made of bakelite and had platinum electrodes. Objectives were employed which had a working distance of at least three millimeters,1 and the parts of the mounting which came in contact with

Jan 1, 1935

By Leon H. Nelson

Several factors which affect the segregation and solidification of killed hot-topped steel ingots are: (1) pouring temperature, (2) volume in the hot top, (3) taper in the ingot, (4) pouring rate by varying the nozzle size, (5) segregation of several elements, (6) moving ingots before completely solidified. In most of this discussion, segregation will be measured in terms of carbon variation only. All the data given are results on S.A.E. 1040 analysis of fully killed steel direct-poured in hot-topped molds giving 20-in, square ingots. Thus the variables of analysis and ingot size and contour are eliminated. Segregation results are all on the rolled-bloom size, not on the ingot itself. They are results from plant-control work and not results of special research on ingot segregation. Pouring Temperature The temperature (or, more correctly, the amount of superheat above the liquidus-solidus) of the steel entering the ingot is, of course, one of the most important factors influencing segregation and solidification. Table 1 gives the average segregation of a number of heats of S.A.E. 1040 steel with normal pouring temperatures of 2775" to 2825" F. The table also gives some data on segregation in hot heats (pouring temperature 2840" to 2870" F.) and in cold heats with some skull (poured at 2725" to 2760" F.). The results in Table 1 are on steel ingots with 20-in. square cross section and 60 in. long to the hot top. The ingot weighs 7100 lb. and the hot top contains 14.3 per cent of the total ingot volume and 11.2 per cent of the total ingot weight. The results are from drillings after rolling the ingots to bloom size. Segregation results obtained on the bloom are probably not as great as they would be in the ingot itself, since heating the ingots for rolling can perhaps cause some migration of carbon from regions of high and low carbon to those of average carbon content.

Jan 1, 1937

By Josef Intrater

A dilatometric determination of the a + ß region temperature limits was performed on vacuum melted Zircaloy-2. The temperature of transformation for a-a+ß and a+ß — ß on heating and cooling as a function of rate of heating and heat treating history was studied. The limits were found to be 815° to 830°C to 975° to 995°C on heating and from 960° to 930°C to 785° to 770°C on cooling. A 5° to 15°C increase was observed for a- a + ß with increased rate of heating and a 20° to 30°C decrease for ß - a + ß with increased rate of cooling. 1 HE transformation temperature for pure zirconium has been determined by many investigators1-5 using metallography, electrical resistivity measurements, and dilatometry. The effect of the rate of cooling on the transformation temperature of zirconium has been studied by Hayes and Kaufmann6 and Duwez,7 and the effect of alloying elements by pfei18 and McGeary.13 Since the development of Zircaloy-2, the limits of the a + ß region for that alloy have been also determined. The first reported temperature for the a — a + a transformation in Zircaloy-2 was 900°C and for a + ß - ß 1000C Subsequent studies by Picklesimer and damson" indicated the beginning of the transformation at 810°C, and the metallographic study by the Technology Group of the Special Materials Section at the Westinghouse Bettis plant1' suggested that 820°to 830°C is the temperature of transformation. The dilatometric investigation by the latter group yielded 830°C for the beginning of the transformation. Thomas and Forscher12 set the beginning of the transformation at 900 °C on heating and the end of the transformation at 870°C on cooling. The above investigators stated in their paper that the dilatometric curve exhibits features caused by a eutectoid reac-

Jan 1, 1962

By M. S. Seltzer

In a previous paper1 it was shown that activation energies for steady-state creep in lead sulfide single crystals varied with the concentration of electronic defects. For n-type lead-excess crystals, values for the creep activation energy, Qc, decreased from 2.9 to 2.2 ev as the carrier concentration increased from 1017 to 1017 electrons per cu cm, while Q, increased from 1.6 to 2.3 ev for p-type sulfur-excess crystals as the concentration of holes increased from 6 X 1017 to 1018 per cu cm. It was also shown in Ref. 1 that the Q, values could best be correlated with the sum of the self-diffusion activation energies in PbS, i.e., for a given concentration of electrons or holes Q, = QPb + Qs, where Qpb and QS are the activation energies for diffusion of pb210 and s35 in PbS. This result suggests that creep rates are controlled by at least two atomic defects, one for lead migration and one controlling sulfur transport. It would be most desirable to interpret these creep energies in terms of an atomic defect disorder model for lead sulfide. Studies of creep rates as a function of sulfur pressure2 indicate that the defects controlling creep rates are singly ionized lead and sulfur vacancies, VPb and Vs. This hypothesis can be more firmly established by determination of Q, under conditions of constant atomic defect concentration rather than constant electronic defect concentration as has been previously done. Therefore, several measurements have been made of Q, on crystals whose con- centration of lead vacancies or sulfur vacancies has been fixed by equilibration under appropriate sulfur pressure and temperature. It was indicated in Ref. 2 that high-temperature isotherms are available which show how the concentrations of various atomic point defects in PbS vary with composition over the entire homogeneity range for the compound. Two such isotherms are shown in Fig. 1 for 900" and 1000°K. Utilizing these isotherms the concentration of a given defect, say Vbb, may be held constant over a particular temperature range by adjusting the sulfur pressure as the temperature is changed. Thus the concentration of one defect suspected of controlling creep rates may be held constant while other defect concentrations vary. The apparent activation energy for formation of these defects can be obtained from the isotherms giving their concentration as a function of sulfur pressure. Activation energies for creep obtained under conditions of constant defect concentration can then be compared with defect formation energies and certain possible atomic defects can be eliminated as creep-controlling species. We have performed creep experiments as a function of temperature at a stress of 244 g per sq mm under conditions which fixed the lead vacancy concentration, V', at 1016, 3.2 x 1016, and 3.2 x 1017 cm-3, and one were the sulfur vacancy concentration, Vs, was held at lo17 cm-3. The results are presented in Fig. 2 as creep rate, k, vs reciprocal of absolute temperature, 1/T. Specimens 34, 35, and 36 were deformed under constant lead vacancy concentration while specimen

Jan 1, 1969

By J. B. Berkowitz-Mattuck, R. Hopper, L. Kaufman, E. V. Clougherty

MARNOCH has reported on the attractive high-temperature oxidation resistance of Hf-Ta alloys.' In view of current interest in these alloys, three Hf-Ta alloys were tested in the present study. These included a Hf-27Ta alloy and a Hf-20Ta-2Mo alloy which were supplied by Marquardt Corp. and a Hf-20Ta-Zr alloy provided by Illinois Institute of Technology Research Institute.' The microstructure of these alloys was heated inductively in a glass vacuum system; the oxidizing gas, helium carrier plus a known partial pressure of oxygen (35-102 Torr), was continually passed over the sample at temperature for a given time period. The concentration of oxygen in the gas stream was continuously measured by a differential thermal conductivity technique2 so that the rate of oxygen picked up by the sample could be obtained. The flow rates were 0.1 to 0.2 ft per sec in the vicinity of the specimen. The concentration of oxygen did not fall below 50 pct of the input level in any of the experiments. In several cases a single sample was exposed consecutively at a series of increasing temperature levels. In a second system at ManLabs, cylindrical specimens were exposed to flowing air in a z irconia tube which was heated by radiation from a carbon tube resistance furnace. The specimen was heated from room temperature to the test temperature in flowing argon, then oxidized in air flowing at 0.1 to 0.2 ft per sec. Following exposure, the air was displaced by argon and the specimen was cooled. Postoxidation metallography was performed on every sample. The depth of conversion of the metal matrix to oxide was measured as shown in Fig. 1. The conversion depth was obtained by measuring the oxygen-contaminated metallic zone (which is bounded by a dense outer oxide and a subscale oxide region), subtracting its dimensions from the original dimensions, and dividing by two. Preferential oxidation of

Jan 1, 1968

By L. I. Cothern

THE introduction of mechanized mining has created a demand for long working faces. It has also prompted mining men to contest the old theory that longwall methods can be used only where roof conditions are ideal and where pack-wall material is plentiful. "Longwall" as used in this paper means "modified longwall," "semi-longwall," or any of the various "wall" or "long-face" methods of mining. Many mines are now using long conveyor faces that differ only in their methods of development, types of roof support and method of loading coal onto the conveyor. Some types of longwall operations are being carried on successfully under conditions heretofore considered impossible by men experienced in longwall mining. With possibly one or two exceptions, long-face methods in Alabama are a direct result of the need for lower mining costs. The advantages over room-and-pillar systems were clearly expressed in an article by Messrs. Fies and Lacy of the DeBardeleben Coal Corporation1 as follows: (1) increased tonnage per miner; (2) increased percentage of lump coal; (3) reduction in cost of development; (4) elimination of the cost of room yardage; (5) reduction in the cost of haulage, from ability to use larger cars; (6) reduction in the cost of machine cutting; (7) reduction in cost for tracks; (8) reduction in the cost of deadwork; (9) reduction in the cost of supervision. An attempt on the part of the operator to gain these, advantages by changing from room-and-pillar to longwall requires considerable courage, and credit should be given to those men who have done their bit to meet the competition of rival fuels. The initiatory problems to be solved are in reference to: (1) retreating or advancing system, (2) length of wall, (3) method of roof support, (4) method of entry development, (5) type of conveyor or loader, (6) hand vs. machine loading (onto conveyors), (7) hand vs. machine loading in entries, (8) control of roof pressure,

Jan 1, 1940

By L. I. Cothern

The introduction of mechanized mining has created a demand for long working faces. It has also prompted mining men to contest the old theory that longwall methods can be used only where roof conditions are ideal and where pack-wall material is plentiful. "Longwall" as used in this paper means "modified longwall," "semi-longwall," or any of the various ''wall" or "long-face" methods of mining. Many mines are now using long conveyor faces that differ only in their methods of development, types of roof support and method of loading coal onto the conveyor. Some types of longwall operations are being carried on successfully under conditions heretofore considered impossible by men experienced in longwall mining. With possibly one or two exceptions, long-face methods in Alabama are a direct result of the need for lower mining costs. The advantages over room-and-pillar systems were clearly expressed in an article by Messrs. Fies and Lacy of the DeBardeleben Coal Corporation1 as follows: (1) increased tonnage per miner; (2) increased percentage of lump coal; (3) reduction in cost of development; (4) elimination of the cost of room yardage; (5) reduction in the cost of haulage, from ability to use larger cars; (6) reduction in the cost of machine cutting; (7) reduction in cost for tracks; (8) reduction in the cost of deadwork; (9) reduction in the cost of supervision. An attempt on the part of the operator to gain these advantages by changing from room-and-pillar to longwall requires considerable courage, and credit should be given to those men who have done their bit to meet the competition of rival fuels. The initiatory problems to be solved are in reference to: (1) retreating or advancing system, (2) length of wall, (3) method of roof support, (4) method of entry development, (5) type of conveyor or loader, (6) hand vs. machine loading (onto conveyors), (7) hand vs. machine loading in entries, (8) control of roof pressure,

Jan 1, 1940

By L. I. Cothern

The introduction of mechanized mining has created a demand for long working faces. It has also prompted mining men to contest the old theory that longwall methods can be used only where roof conditions are ideal and where pack-wall material is plentiful. "Longwall" as used in this paper means "modified longwall," "semi-longwall," or any of the various ''wall" or "long-face" methods of mining. Many mines are now using long conveyor faces that differ only in their methods of development, types of roof support and method of loading coal onto the conveyor. Some types of longwall operations are being carried on successfully under conditions heretofore considered impossible by men experienced in longwall mining. With possibly one or two exceptions, long-face methods in Alabama are a direct result of the need for lower mining costs. The advantages over room-and-pillar systems were clearly expressed in an article by Messrs. Fies and Lacy of the DeBardeleben Coal Corporation1 as follows: (1) increased tonnage per miner; (2) increased percentage of lump coal; (3) reduction in cost of development; (4) elimination of the cost of room yardage; (5) reduction in the cost of haulage, from ability to use larger cars; (6) reduction in the cost of machine cutting; (7) reduction in cost for tracks; (8) reduction in the cost of deadwork; (9) reduction in the cost of supervision. An attempt on the part of the operator to gain these advantages by changing from room-and-pillar to longwall requires considerable courage, and credit should be given to those men who have done their bit to meet the competition of rival fuels. The initiatory problems to be solved are in reference to: (1) retreating or advancing system, (2) length of wall, (3) method of roof support, (4) method of entry development, (5) type of conveyor or loader, (6) hand vs. machine loading (onto conveyors), (7) hand vs. machine loading in entries, (8) control of roof pressure,

Jan 1, 1940