Search Documents

By R. W. Wittkopp, J. D. Stephens

In a device known as the electron-beam microprobe, the mining industry has lately acquired a sophisticated new analytical tool that can dig out answers to a broad range of questions spanning all phases of mining activity. Essentially, the microprobe is a specialized X-ray fluorescence unit that makes it possible to obtain chemical analytical data for volumes as small as 1 cup. With this capability, it can be used both for determining the composition of small inclusions in rocks or metallic products and for monitoring changes in composition that proceed from a reacting surface. At the Research Center of Kennecott's Metal Mining Division, this versatile probe has successfully solved problems in mineral operations ranging from exploration through refining. A few instances of how the probe has been applied at the Center are presented here. In Mineral Exploration-A Good Look Before Leaping Since the objective of mineral exploration is to locate deposits of materials which can be processed at a profit, the mode of occurrence of elements or minerals in the deposits is important.

Jan 1, 1970

By John Dasher, M. C. Chang

The Crucible mine in Pennsylvania, operating on Pittsburgh seam coal, is rated at 5000 tpd. The washing plant, built in 1943, is rated at about 400 tph, using hydroseparator boxes to wash the coarse coal (4 x 5/16 in.) and hydrotator units for the fine coal (5/16 x 0). It is generally acknowledged that gravity concentration equipment cannot be used efficiently to beneficiate coal finer than about 65 mesh. Before the present flotation circuit was installed, Crucible recovered its fine coal slurry, predominantly -24 mesh material, by passing it through a battery of five 14-in. and one hundred and ten 3-in. Hey1 & Patterson cyclones in parallel with a 75-ft Dorr thickener. About two thirds went to the cyclones and one third to the thickener. Underflows from cyclones and thickener were filtered, respectively, in one 12-disk Eimco and two 4-disk Oliver filters fitted with stainless steel cloth. The resulting cakes were added to the coarse metallurgical coal. The filtrates, overflow from the 3-in. cyclones, and thickener overflow were recycled to the coarse coal plant.

Jan 3, 1959

By John P. Cosgro

The increasing use of internal furnace-boilers for power-plants at mines (doubtless due to the facility with which they may be installed by reason of their portability; the fact that they require no masonry setting, cast-iron fronts, buck-stays, etc., and practically no foundation; and the successful maintenance of their claim to equal and even superior economy, as compared with boilers of other types1) warrants this description of a method of remedying an injury which may occur, to such a furnace, even though it satisfies the requirements of the formula adopted by the U. S. Board of Supervising Inspectors of Steam Vessels.2 I refer to the sagging and deformation which may result from overloading the boilers for a considerable period—say, several days. This is sometimes unavoidable under the exacting conditions of continuous day-and-night service, and (in spite of all rules and precautions) the occasional careless or unskillful work of attendants. Such a trouble is by no means unknown on shipboard, where this type of boiler is so largely employed.

Jan 1, 1906

PAUL D. MERICA,* Washington, D. C. (written discussion t).-This paper is a discussion of some of the results of a recent investigation1 of Prof. Zay Jeffries, and of his interpretation and generalizations from these results. This work I have followed with great interest and with appreciation of its value in clarifying our views on the nature of deformation in metals and its relation to structure. It is only by such close study of the relation of structure to mechanical properties that we shall ever be able to describe the latter in terms of their ultimate elements, and thus explain what are still mysteries in the mechanical behavior of metals; experiment and thought along these lines are in my opinion of the utmost value. If I, therefore, here record some of the difficulties I have experienced in understanding some of the generalizations of Prof. Jeffries, it is only in order that perhaps from the discussion may emerge a clearer and more consistent statement of hypothesis or theory in explanation of the facts discovered by him.

Jan 11, 1918

"Copper was first made in Butte by the use of iron for its precipitation from mine water in 1890. In consequence of a fire breaking out in the St. Lawrence mine of the Anaconda Copper Mining Company in November, 1889, a large quantity of water was poured into the workings, with the intention of flooding the mine and extinguishing the fire. This proved to be impracticable, but this water, on being pumped to the surface, was found to be high in copper sulphate,—tradition says 75/100 of 1 per cent. The Anaconda Copper Mining Company gave Wm. Ledford a lease on this water. He first (lug holes into the ground, filled them with scrap iron and allowed the water to flow through them. Later he built an open-top flume which he partially filled with iron and passed the water through the by the iron precipitation method. An assay in- the year 1890 from Gagnon mine water, showed .0016 per cent or 28 lbs. copper per day. The mine was then opened to the 1,000 level.None of the mine waters encountered in the solid rock in the mines of Butte contained copper in sufficient quantity to produce the metal profitably by the iron precipitation method. An assay in the year 1890 from Gagnon mine water, showed .0016 per cent or 28 lbs. copper per day. The mine was then opened to the 1,000 level."

Jan 1, 1913

By H. De. Cizancourt

There is no new outstanding fact to be noted concerning the development of petroleum production and research in France and her possessions during 1935. France.—Pechelbronn remains the only important producing field in France. The total output has reached 538,921 bbl., showing a small decrease on last year's figures. Out of this, 302,737 bbl. was extracted by drilling and 236,184 bbl. (44 per cent) was obtained by means of shafts and galleries. Exploration of deeper formations was still in progress, and resulted in the discovery of a new Middle Triassic (Muschel-Kalk) producing horizon. In the vicinity of Hirtzbach (South Alsace) shallow exploration tests (500 ft.) were drilled by the Société de Pechelbronn, oil indications being found in the Tertiary. Two more important wells are now drilling in deeper horizons. The Chantenay well (Niévre) was finished in August, 1935, at a depth of 3544 ft.1 A test is under progress in Savoie. South of Gabian, at Pezenas, the erection of a rig is nearly completed.

Jan 1, 1936

There is no new outstanding fact to be noted concerning the development of petroleum production and research in France and her possessions during 1935. France.—Pechelbronn remains the only important producing field in France. The total output has reached 538,921 bbl., showing a small decrease on last year's figures. Out of this, 302,737 bbl. was extracted by drilling and 236,184 bbl. (44 per cent) was obtained by means of shafts and galleries. Exploration of deeper formations was still in progress, and resulted in the discovery of a new Middle Triassic (Muschel-Kalk) producing horizon. In the vicinity of Hirtzbach (South Alsace) shallow exploration tests (500 ft.) were drilled by the Société de Pechelbronn, oil indications being found in the Tertiary. Two more important wells are now drilling in deeper horizons. The Chantenay well (Niévre) was finished in August, 1935, at a depth of 3544 ft.1 A test is under progress in Savoie. South of Gabian, at Pezenas, the erection of a rig is nearly completed.

Jan 1, 1936

By M. M. Fine

Normally the U. S. produces less than 10 pct of its annual manganese requirement. About 95 pct of domestic consumption is used by the steel industry.1 The strategic and critical nature of manganese has been recognized by its inclusion in the national stockpile and by intensified research directed toward cataloging and evaluating domestic manganiferous deposits. The USBM has participated in these activities for many years with field and laboratory studies to assess the extent and potential utilization of domestic manganese ores. One area of particular interest is in the vinicity of Batesville, Ark., where deposits have been mined since 1849 for both manganese and ferruginous manganese ores. Production is centered in Independence County, but deposits are also found in Sharp, Izard, and Stone counties in north- central Arkansas. Miser has described the geology and manganese mineralization in some detail.2,3 The rocks of the area are sedimentary, consisting of sandstone, limestone, shale, and chert. The two formations of greatest importance,4 Fernvale lime- stone and Cason shale, are host rocks of the primary manganese mineralization.

Jan 8, 1959

The Library of the above-named Societies is open from 9 A.M. to 10 P.M., except on holidays. It contains about 70,000 volumes and 90,000 pamphlets, including sets of technical periodicals and the publications of - scientific and technical societies members of the Institute, with few exceptions, are forced to spend a portion of their time 'in localities isolated from sources of information. To these the Library, through its Library Service Bureau, can render - valuable service through correspondence; letters requesting information will receive especial attention. The Library is prepared to furnish references and photographic copies of articles on mining and metallurgical subjects; to determine the existence of mining maps, and to furnish genera1 information on the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape.

Jan 10, 1916

By Roger A. Harris

INTRODUCTION The Kidd Creek Mine produces a total of 3.6 million tons annually. Geologically the orebody is complex, containing rich values of zinc, copper, silver and lead which are mined and milled as two separate "ore types". Production is mainly from highly mechanized sub-level open stopes of approximately 300,000 tons each. The Mine Engineering Department has developed, and now operates, a computer system that is the subject of this report. It was created specifically to aid the daily work of the mining engineer and has features that are new and possibly unique in the industry. DESIGN OBJECTIVES In 1971 a task force, set up to investigate the subject of computer assistance to mine engineering, specified four design requirements which it felt a successful application had to satisfy. They were:- 1) The computer had to offer a TOTAL SYSTEM that was fully integrated into the routine mine engineering function. 2) The computer had to be directly usable by the current engineering staff, the majority of which had received no formal training in computing.

Jan 1, 1977

By Luis Toron, Salvador Cortes-Obregon

THE Oaxaca coal fields, shown in Fig. 1, are located in the Alta Mixteca region in the states of Oaxaca, Puebla, and Guerrero. Known out crops are scattered over 3125 square miles. It is probable that further exploration will reveal a more extensive area of deposits. The region is of great importance to Mexico, as at present the only sources of coal are the fields near the U. S. border. Steel mills are also located in the North, and finished products must travel 600 to 800 miles to the area of consumption in central Mexico. The Oaxaca coal, only 120 miles south of Mexico, D.F., lies close to several iron ore deposits. If this coal can be used in steel production is will be possible for the Mexican steel industry to reach new dimensions, commensurate with the growing industry of the central region. Coal can be utilized in thermoelectric plants in this area, which lacks not only petroleum and natural gas but also electric power. It can be used as domestic fuel, replacing charcoal and firewood.

Jan 5, 1954

By R. W. Heckel, R. L. DeGregorio

The DeHoff method of determining the size distribution of ellipsoid-shaped, second-phase particles has been applied to the spheroidization of cementite in a eutectoid steel. The surface area of Precipitates determined from the various size fractions in the distribution was correlated with surface-area measurements based on the number of intersected interfaces on a random lest line. The precipitate particles were found to be oblate ellipsoids with an axial ratio of about 0.90. The size distributions were found to be log-normal. A method is proposed whereby the shrinkage of small particles and growth of large ones can be determined from the experimental data. The experimental data are compared to previously proposed mathematical models describing diffusion-controlled kinetics and various types of interface-controlled kinetics. The experimental growth and shrinkage rates are considerably slower than those predicted by diffusion-controlled kinetics. The best fit is obtained for a model describing interface-controlled kinetics limited by the rate of formation of cementite at the growing interfaces where the interfacial reaction rate is proportional to the solute thermodynamic activity gradient across the surface. THE subject of spheroidization of second-phase particles has been considered previously by other investigators. Livingston1 has studied the precipitation of the cobalt-rich phase from copper alloys containing 0.7 to 3.2 wt pet Co. His results indicate that the average particle size increases as the cube root of the heat treatment time in accord with diffusion-controlled kinetics.'-' Komatsu and rant' in their studies of the growth of SiO2 in a dispersion-strengthened copper-silica alloy found that the initial growth of SiO2 proceeded by diffusion-controlled growth and later stages were limited by interface-controlled growth. The values of the activation energy obtained for the interface- controlled process led them to the conclusion that the process was limited by the dissociation of SiO2 at the shrinking interface. The transition from diffusion-controlled growth to interface-controlled growth was characterized by a particle size which varied with the heat-treatment temperature. It is also interesting to note that the particle-size distribution as found by Komatsu and Grant exhibits log-normal behavior when replotted on log-probability coordinates. Dromsky, Lenel, and Ansell9 have observed the growth of Al2O3 particles having a mean free path of about 1.5 to 13 µ. Their photomicrographs indicate that the Al2O3 particle sizes were larger than those observed by Komatsu and Grant. Dromsky, Lenel, and Ansell concluded that the Al2O3 coarsened by an interface-controlled growth mechanism limited by the solution of A12O3 at the shrinking interfaces. Bannyh, Modin, and Modin10 have studied the spheroidization of a eutectoid steel (0.83 wt pet C). Their spheroidization (tempering) treatments were carried out in the range from 210o to 700°C for times between 1.5 sec and 20 hr. Measurements of mean particle size as a function of time indicated a cube root of time dependence of size at 700°C, in agreement with previous analyses of diffusion-controlled kinetics.2°7 At lower temperatures, the time dependence was less than the one-third power. It is important to note that, although mathematical models of growth* considering particle-size distribution have been available, measurements of only mean particle size have been carried out. DeHoff11 has presented a quantitative metallography technique which is applicable to the determination of the size distribution of ellipsoids of constant shape. This method is applicable to both oblate and prolate ellipsoids of all ratios of minor to major axis and is based upon an extension of Saltykov's analysis12 of the distribution of spheres of varying size. DeHoff's analysis is based upon measurements of the minor axis of the particles on a random plane of polish in a unit area. This method provides a measure of the number of ellipsoids in various size ranges per unit area. As pointed out by DeHoff, such measurements may be used to obtain surface area and total precipitate volume data. Thus, the accuracy of the distribution analysis may be checked by comparison of the surface and volume

Jan 1, 1965

By J. Lewis, J. Harper, M. F. Ashby

A grain boundary in a metal interacts with second-phase particles, which exert a pinning force (first estimated by Zener) on the boundary opposing its motion. We have computed the shape of boundaries which interact with more or less spherical second-phase particles and have constructed a soap-film model to reproduce the shape of the boundary surface. An important result is that measurement of this shape allows the pressure, or driving force, on the boundary to be measured. We hare applied this technique to grain boundaries in two alloys and hate measured the pinning force exerted by single second-phase jwrticles on the boundaries. It is in good agreement with Zener's estimate. J\. boundary between two grains, or two bulk phases, interacts with small inclusions or particles of a second phase, whether they are gas or solid. This interaction means that the boundary, forced to migrate by a difference in free energy between the material of the two grains or phases which it separates, exerts a force on a particle which it touches, tending to drag it forward. (The movement of inclusions through metals under the influence of this force, has, in fact, been observed. 1-3) Equally, the particle can be thought of as exerting a pinning force on the boundary, tending to hold it back. Zener (in a celebrated private communication4) first realized that this interaction, and the resulting pinning force, existed. His calculation of its magnitude was crude but adequate: a spherical inclusion of radius r blanks off an area nr2 of the boundary on which it sits; since the boundary has an energy of rMM x per unit area, the blanlung-olf decreases the energy of the system by MM: this energy is returned to the system if the boundary is pulled free from the inclusion— a forward movement of the boundary by a distance r will do this—so that the maximum pinning force is Trrym.M- A similar argument can be made for inter-phase boundaries. The nature of the particle itself did not enter this, or two subsequent treatments.5,6 When it is considered, tic leifthe energyoftheb a) The boundary may enter and pass through the particle if the energy of the boundary is lower within the particle than in the matrix. Fig. l(r/). Certain coherent precipitate particles behave like this. h) More usually, the boundary will bend round the particle, enveloping and bypassing it. Fig. l(b). In doing so, it changes the structure and energy of the interface between the particle and its matrix. This means that the boundary does not touch the particle surface at right angles, as early treatments assumed,5'9 but at some angle a which depends on this change in surface energy of the particle, and can be calculated from the equilibrium of surface tensions. Most precipitate particles and inclusions behave like this. Gas bubbles or liquid drops can be regarded as belonging to either group. The progress of bypassing is conveniently measured by the angle shown in Fig. 1. When the nature of the particle is ignored, its maximum pinning force is exerted when - 45 deg. When it is considered, this critical value of is found to depend on a and thus on the nature of the particle. The maximum pinning force lies between nryMM and 2jtjMM (Appendix 1). not very different from Zener's result. In reality, a boundary between crystals has a specific energy and tension which varies with the orientation of the boundary. Furthermore, recent experiments7 indicate that such a boundary is not atom-ically smooth, but has steps on it: migration of the boundary corresponds to the sweeping of these steps across the boundary surface, like the Frank model of crystal growth from the vapor. This means that the interaction of a boundary with particles should really be considered in terms of the way in which particles hinder the movement of these steps. To suppose a grain boundary or interphase boundary to be smooth, and to ignore the variation of its energy with orientation, is to liken it to a soap film. The advantage of this soap film approximation, which we have used throughout this paper, is that interaction energies and boundary shapes can be calculated easily. We have done this by numerical computation and by using a soap film model, and have compared the results with grain boundaries in an aluminum-based and a copper-based alloy. It turns out that the shape of the boundary which bulges between particles allows the pressure an it to be calculated; that is, the local driving force an the boundary can be measured. This has allowed us to check the Zener relationship experimentally.

Jan 1, 1970

By D. A. Elgillani, M. C. Fuerstenau

With either sulfonate or oleate as collector, quartz responds to flotation with moderate additions of calcium only at moderately high pH, where some portion of the activator has hydrolyzed to caOH+ . Calculations of the concentrations of various ionic and precipitated species of calcium and collectors suggest that the products of [(CaOH+) (RSO3)] and [(CaOH+)(01-)] determine whether flotation is obtained under specific conditions. Ion products on the order of 10-12 were calculated for both the sulfonate and oleate systems. The activating effect of calcium ion in nonmetallic flotation systems is of considerable interest because of the normal presence of calcium in natural water. As a result, this phenomenon has received quite some attention in the past. Kraeber and Boppel1 showed that quartz could be activated by calcium above pH 10 with sulfonate as collector. The feasibility of selectively separating quartz from hematite with calcium activation at relatively high pH was demonstrated by Clemmer, Clemmons, Rampacek, Williams, and stacy.2 Cooke and Digre3 showed with a bubble pick-up method that the minimum quantity of calcium ion required as activator for complete pick-up of particles occurs at pH 11.5 for an addition of 20 mg per liter sodium oleate. They also showed that larger additions of calcium (10-fold increase per unit decrease of pH) must be added for complete bubble pick-up as the pH is reduced. Schuhmann and Prakash,4 using a vacuum flotation technique, found that quartz could be floated with moderate additions of calcium chloride and oleic acid at neutral pH, providing the metal ion was present in stoichiometric excess over the quantity needed to form the normal soap with oleic acid. They also reported that calcium will function as an activator only in basic media. More recently, Eigeles and volova5 have shown that essentially complete flotation of quartz is obtained with 6 x 10-4 mole per liter calcium chloride and 1.7 x 10-5 mole per liter sodium oleate at pH 11.6. while no flotation is obtained at about pH 10.9 and below. The importance of adsorption of activator and collector at the air-liquid interface is also demonstrated in these systems. The important role that metal ion hydrolysis assumes in quartz activation systems was also demonstrated recently.6-8 A detailed investigation of metal activation in sulfonate flotation of quartz was undertaken in one system7 and yielded a number of interesting and important observations. Quantification of the data of this system7 to the extent desired was not possible, though, because certain species could neither be ignored nor accounted for accurately. These difficulties can be circumvented when calcium is involved as activator. This detailed analysis was undertaken to obtain a more quantitative explanation of calcium and metal ion activation in quartz flotation. EXPERIMENTAL MATERIALS AND METHODS Sodium alkyl aryl sulfonate9 mol wt 450, and pure potassium oleate were used as collectors. All other reagents used were reagent grade in quality, i.e., n-amyl alcohol as frother, KOH for pH adjustment, and calcium chloride. Conductivity water, made by passing distilled water through an ion exchange column, was used in the investigation. Quartz was prepared by leaching the sized sample (48 x 150 mesh) with HC1 until no iron could be detected in the leach liquor. The experimental equipment and procedure were the same as that described previously.6,10 EXPERIMENTAL RESULTS As the presence of precipitates was noted in all of the systems to which ca++ and collector were added, experiments were undertaken to determine the solubility products of calcium sulfonate and calcium oleate using a nephelometer. With this technique, collector is titrated into a known solution, which in this case was 5 x 10-5 mole per liter CaCl2 at pH 5.5. Upon precipitation of the calcium-col lector salt, e.g., calcium oleate, light is scattered and detected

Jan 1, 1967

By A. D. K. Laird, C. A. Johnson

Drag coefficients for a cylinder being towed through water at constant velocity and also at constant linear acceleration were measured. Drag coefficients for constant velocity towing showed reasonable agreement with previous results. The drag coefficients found for constant acceleration showed little correlation with either the magnitude of the acceleration or the value of the modulus AD/V2 and tended to be slightly lower than those for constant velocity. INTRODUCTION For the design of offshore structures, wave forces acting on immersed cylinders are of importance. Several investigations have been made of these forces and of how they can be predicted from wave theories. A paper by Crooke' summarizes much of the work already done. More recent research by the Wave Research Laboratory at the University of California, Berkeley, has added much to the body of data collected under ocean wave conditions, but has not found a reliable method of force prediction from basic theories of wave motion. The present investigation is part of a long-range program to collect data with which to test current and future theories and correlations. The immediate objective was to measure drag forces on a circular cylinder subjected to linear accelerations over the range of Reynolds numbers between l04 and 105 where the drag coefficient was a constant for constant velocities. In particular, the effect of constant acceleration from rest and from uniform motion was to be investigated. The effect of acceleration may be evaluated in terms of drag coefficients. A useful resistance coefficient, C, is defined by the equation for total drag force, D, exerted by the fluid on the cylinder. DT =CSp V2/2.........(1) The coefficient C may be plotted as a function of the parameter AD/V2. Here D is the diameter and S is the projected area of the cylinder. The acceleration and velocity are A and V. The mass density of the fluid is p. An alternate drag coefficient, C, corresponds to the total force of the fluid opposing the motion minus the virtual mass force. This drag coefficient, arising from the velocity of the fluid, may be compared with that for the same cylinder in uniform motion. The similarities and differences between this coefficient as calculated for accelerated and for steady motion are of interest in the inverse process of predicting drag forces on cylinders under arbitrary conditions. One serious difficulty in this method is the specification of the virtual mass which depends also on the flow picture about the cylinder.1 EXPERIMENTAL EQUIPMENT The experiment was performed in the combination wave and towing tank at the Engineering Field Station of the University of California. The tank is 200 ft long, 8 ft wide, and 6 ft deep. The tow carriage is externally propelled by a cable, and the velocity of the carriage is maintained essentially constant by means of an am-plidyne. For the purpose of the present investigation, the speed control of the amplidyne was modified by inserting a linear speed control rheostat, which was rotated at a constant speed by a small d-c motor equipped with a slip-clutch. Accelerations which were constant over a reasonable length of time were thus produced. The magnitude of the acceleration depended upon the speed of the d-c motor and the limiting speed of the carriage. Data were obtained for a range of accelerations of 2 to 10 ft/sec,2 and a range of velocities of 2 to 15 ft/sec. An accelerometer (Statham Type C-2-350) with a range of ±2g was attached to the carriage and connected to a Brush analyzer and penmotor. A continuous coil of wire with 10 turns/ft wound around a fixed wooden form extending for a distance of 40 ft along the length of the tank was connected by an electrical contact mounted on the carriage to a Brush analyzer and penmotor, to give the time-position history for each run. The test cylinder was machined from solid aluminum alloy, 17-ST. to a diameter of 1.250 in., and could be

Jan 1, 1957

By R. L. Mauger, P. E. Damon, B. J. Giletti

This report includes the lead isotopic dating of a suite of galenas from Arizona and an application of the K-Ar method to the dating of a Laramide porphyry copper deposit, the Silver Bell Mining District. The lead isotopic data supports prior age assignments based upon geologic inference. The Silver Bell study illustrates the necessity of correlative geologic and petrographic investigations for the interpretation of the results of potassium-argon dating. LEAD ISOTOPIC DATING OF GALENAS FROM ARIZONA ORE DEPOSITS A group of galenas from Arizona ore deposits have been analyzed for lead isotope ratios. The results were used to calculate model ages by the. method of Russell, Stanton and Farquhar,l6 in which the age is calculated directly from the Pb206/Pb207 ratio. The use of Pb206/Pb207 ratios eliminates the errors inherent in measuring the abundance of Pb204. The Holmes-Houtermanns model is the other model commonly used for calculating model ages. Both models assume that any lead sample is composed of primeval and radiogenic components and the calculated age is the time at which the lead was extracted from its source area. Using the Holmes-Houtermanns model, a lead is ordinary if its isotopic ratios lie on an isochron. The growth curve that passes through the experimental point determines the U/Pb ratio in the source area. The RSF model assumes the source area for conformable leads is the mantle, that this has a uniform U/Pb ratio, and thus all ordinary leads must lie on a single growth curve, having a mantle U/Pb ratio. The definition of an ordinary lead differs between the models, and differences in age arise mainly from the assumptions made to evaluate parameters in the model equations. These assumptions depend on the hypothesis chosen to explain ore genesis. In the RSF Model, the Pb206/Pb207 ratio is derived as a function of time. The equation contains three undetermined parameters which are evaluated by assuming three known points lie on the curve. These are the following: 1) Primeval lead from the Canyon Diablo and Henbury meteorites, 2) Modern conformable leads which lie on Patterson's zero isochron, 3) Lead from the Bathurst, New Brunswick base metal deposits. The Bathurst deposits are postulated to be examples of "conformable base metal deposits", as proposed by Stanton.l9 A conformable deposit has a particular genetic history and, as a result, the orebody conforms to stratigraphic layering in the host rock. The metals are brought to the surface in volcanic rocks which originated in the mantle. Weathering products of these rocks, including sulfur and metals, accumulate in areas undergoing sedimentation. The formation of sulfide ion in the sediments by the action of sulfate reducing bacteria causes fixation of iron as pyrite. If the pyrite becomes concentrated in favorable stratigraphic horizons, any base metal deposit eventually formed by replacement of pyrite will have a strata bound character. Compaction and expulsion of pore water from the sediments at depth result in upward mobility of solutions containing soluble base metal chlorides. The strata with high pyrite content act as chemical traps for the base metal ions and replacement occurs. An important result of this general evolutionary model is that, if complete separation of lead and parent isotopes occurred during accumulation of the sediments, any ore deposit formed solely of metals derived from those sedimentary rocks will contain "conformable" lead. This would be true even if the actual ore deposit were formed at a later date by some epigenetic process. In this case, mineralization would be controlled by local conditions, and need not conform to stratigraphic layering. Also, any ore deposit containing lead derived from a mantle or mantle-like source, even though not conformable in Stanton's sense, will fall on the curve for conformable ores and thus give a meaningful model age. Model ages for Arizona galena deposits are listed in Table 1. Fig. 1 is a location map. Jerome-Humbolt District: Galenas from the United Verde mine at Jerome and the Iron King mine at Humbolt give model ages of 1750 m.y. and 1640 m.y. respectively. Both deposits are massive sulfide bodies in a host rock of older Precambrian

Jan 1, 1965

By J. J. Gilman, T. A. Read

S URFACE effects in the cleavage of brittle crystals have been known for some oftime,1, 2 but our knowledge of surface effects in the plastic deformation of crystals is of relatively recent origin. In 1936, Roscoe9 eported his observations comparing oxidized and clean cadmium crystals. He found that cadmium crystals 1/2 mm in diam when covered by an oxide film less than 1200 atoms thick had critical shear stresses about twice those for clean crystals. This effect is anomalous in that it cannot be caused by the inherent shear strength of a normal oxide film. Either an interaction between the film and the crystal causes the large increase in strength, or the oxide film has an abnormal mechanical strength. Several authors since Roscoe have studied surface effects in crystal plasticity. A complete review of the literature will not be presented, but most of the results may be summarized as follows: 1—The critical shear stress for slip is increased markedly by very thin oxide films on zinc4 and cadmium crystals;" ' also, the entire stress-strain curve is raised by an oxide coating;3,4 both effects increase with decreasing specimen radius. 2—Surface active substances such as oleic acid destroy the hardening effect of oxide films.4, 6-8 The time required for the reduction of the hardening effect to begin increases with the viscosity of the solvent4~ 3—There has been dispute in recent years about the effects of surface active substances themselves on plastic deformation. Rehbinder, Lichtmann, and Maslenikov9 state that surface active substances reduce the strength of metal monocrystals markedly and increase the number of slip lines per unit length at a given strain. The effect varies with orientation for tin crystals being smallest for x, = 0, largest for x, = 45", and intermediate as x, + 90°.10 Several workers claim to have disproved the results of Rehbinder')"." but Rehbinder and Lichtmann9 have defended themselves and Masing with his collaborators" has confirmed some of Rehbinder's results. 4—Immersion of metal specimens in electrolytes such as sodium chloride reduces their strength12,13' and subsequent cathodic polarization increases the strength reduction. For noble metals, the strength reduction occurs for both anodic and cathodic polarization," increasing with increasing polarizing voltage. 5—Electroplated copper coatings effect the creep rates of zinc monocrystals. Poly crystals are not affected." 6—Immersion in dilute acid destroys the hardening effect of an hydroxide film. When an acid solution is applied to a steadily creeping crystal, the creep rate jumps to a very high value and then drops gradually to a steady value which is higher than the initial steady rate.*' " If the hydroxide film to be removed is very thin (about 100A thick), the creep rate does not change measurably, but a small rapid strain-increment is observed when dilute acid is applied." 7—Crystal plasticity depends on specimen dimensions. This was observed by Lichtmann and Ven-stroml" for monocrystalline tin and by Andrade and Kennedy" for polycrystalline lead. 8—Immerson of copper crystals in mercury has no effect on their stress-strain curves.'" 9—Bombardment of creeping cadmium crystals with a particles which penetrate the surface to only 0.005 mm may increase their creep rates as much as five times.''' The experiments which will be described in this paper pertain to: (a) the effect of a crystal's shape on its plastic deformation, and (b) the effect of metallic surface films on plastic deformation. For the work pertaining to (a), crystals of zinc, tin, and lead were grown which had various shapes. These were tested in simple tension. Macroscopic rotations about the tension axis which are unpredicted by the classical theory of slip were observed, and serrated edges were observed in tin crystals. For the work pertaining to (b), the effects of evaporated and electrodeposited films of copper, nickel, gold, and zinc on the mechanical properties of zinc, tin, and lead crystals were determined. The films influenced both slip and twinning of the crystals in creep and tensile tests. Experimental Details Chemically pure zinc, tin, and lead were used in this investigation. The zinc was 99.999t pct pure;

Jan 1, 1953

By Byoung Whie Lee

In order to investigate the change in surface energy as a function of cold work ad environment, the contact angles between a liquid and the surface of elec-tropolislzed aluminum with various degrees of cold work were measured. Specinlens cut from aluminum rod (99.99 pct Al) were annealed at 600°C for 24 hr and then cold compressed parallel to the drawing di-rectzon of the rod in increments of approximately 10 pcl from 0 to 70 pct. The sections, taken transversely to the drawing direction, were mechanically and electro chemically polished. Contact angles between the sessile drop of distilled water, glycerin, and glycol and the specimen surface were measured optically. The differences in interfacial energy were calculated from the contact angle data. The effects of chemical washing and surface roughness of the specimen on the contact angle were also studied. The liquid contact angle was a linear function of the degree of cold working (D) ad changed markedly with differed liquids. THE plastic deformation of polycrystalline metals induces a preferred orientation in crystal structure. A preferred orientation changes the atomic density of a metal surface. This change in surface atomic density brings about the changes in surface interactions of the metals."' Also, the plastic deformation of metals raises the internal energy by increasing the stored energy.' Consequently, the total Helmholtz free energy of the metal increases and, in turn, the surface free energy of the metal. In order to study the effect of plastic deformation on solid surface phenomena, the liquid contact angle of a sessile drop made on cold compressed and elec-trochemically polished aluminum was measured. The preferred orientation in aluminum, due to uniaxial compression, is known to be [110] direction parallel to the compression axis. However, this description is only a first approximation of a rather complex orientation. In actuality, half the crystallites are more than 10 deg from this orientation, regardless of the amount of compression." For randomly oriented fcc crystals, the average surface atomic density can be calculated as follows: The number of atoms in a unit volume is 4/a3, where a is a lattice constant. Hence, the number of atoms per unit surface area is about (4/a3)2/3 = 2.52/a2 However, when the preferred orientation took place along [110] direction, the surface atomic density is as follows: The area of (110) plane of a unit cell, considering ridges and valleys, is BYOUNG WHlE LEE, Member AIME, is Research Metallurgist, Atomic Energy Research Institute of the Republic of Korea, Seoul, Korea. Manuscript submitted May 29, 1968. IMD 2 x J2- a x Ga = 6a2 Since this plane contains 4 atoms, the surface atomic density is 4i6a2 = 2.3/a2 Upon changing from random to preferred orientations, the surface atomic density decreases about 10 pct. The increase in the stored energy and the change in surface atomic density due to plastic deformation would certainly alter the surface tension of a metal. EXPERIMENT High purity aluminum rod of 6-mm diam (99.99 pct Al, obtained from Johnson, Matthey & Co., Ltd, London, England) was cut into sections approximately 1 cm long. The transverse cross section was mechanically polished. Then, the specimens were annealed in air at 600°C for 24 hr. Thus, eight annealed specimens were uniaxially compressed at room temperature from 0 to 70 pct of cold working with an increment of 10 pct. The extent of cold working was determined by the percentage of reduction in axial length to the original length. The specimens were further polished mechanically and, then, electrochemically with the Modern Battelle Type 1 electropolishing solution with a current density of 0.3 to 0.4 amp per sq cm and an electrode potential of 8 to 12 v at the solution temperature of 78" to 82°C for approxirr~ately 5 min. The Modern Whlte Diffusing Screen \t/ --------------- re Goniometer for Mercury Lamp ^-^ Sessile Drop ¦=• Condenser c=> Microscope l_*~_i bJ Mlcromster Filer with Protmcter Fig. 1—Schematic diagram of apparatus set-up for liquid contact angle measurement.

Jan 1, 1970

By F. Bonaccorso, G. Venturello, C. Antonione

A study of the effect of small amounts of interstitial impurities on recovery and re crystallization in high-purity iron (99.995 pct) has been undertaken. This paper gives results on the effect of carbon, introduced in small-dosed amounts @om 0.0005 to 0.0086 wt pct) by heating iron specimens of high purity m a static atmosphere of CO + ,. The materials prepared in this way, cold-worked 80 pct and subjected to a series of isochronal and isothermal annealings, were submitted to examinations by X-rays, micrographs, and hardness tests. It was observed that effect of carbon is remarkable in the sense of blocking recovery of mechanical properties up to the temperature at which re crystallization begins. On the contrary, carbon has a negligible effect on primary re crystallization temperature, when compared with the known effect of substitutional impurities. This is in agreement with the high mobility of interstitials. In effect, only a slight decrease, -20 pct, of the grain-boundary motion rate was noted, due to the interaction between the grain boundary and the carbon atoms. On the other hand, in the samples in which the carbon content is above the solubility limit at the temperature at which re crystallization occurs, a slight increase of nucleation frequency is noted due to the presence of precipitated carbides. ThE effect of purity on recovery and recrystalli-zation phenomena has been known for a long time; however, recently, new attention has been given to the problem since new methods for obtaining metals with extremely low impurity contents have become available. Most of this research work essentially concerns the effects of impurities which cause precipitates or give rise to substitutional solid solutions. The works of Bolling and winegard1 and Aust and utter' on lead, and Vandermeer and orddon' on aluminum, 01sen4 on nickel, and Abrahamson and Blakeney on iron should in particular be referred to. On the effect of this type of impurities a quantitative theory has been formulated by Detert and Lucke6 and has lately been discussed critically by Cahn7 and Gordon and vandermeer.' Interstitial solid solutions in iron have not as yet been studied. As the study of the effect of interstitials is of great interest both from a theoretical and practical standpoint, it was deemed useful to examine the effects of carbon, nitrogen, and boron on recovery and primary recrystallization of iron. There already is some work by Chaudron et al.,1-" on the effect of interstitials on iron; their work, however, mainly concerns secondary recrystallization. The present paper refers in particular to the effect of carbon. EXPERIMENTAL PART Preparation of Materials. The pure iron used for this research was obtained from FeCIS recrystal-lized and purified by extraction with isopropylic ether. From the ferric chloride purified in this manner, hydroxide was precipitated with a solution of very pure ammonia, and, by calcination in pure sintered alumina crucibles, oxide was obtained. Reduction of the oxide to iron sponge was performed in sintered alumina tubes with very pure hydrogen at 650°C; at the end of the operation temperature was increased to 900°C. Specimens for the experiments were obtained by sintering the sponge at 1480°C in pure Hz after a pre sinter ing treatment at 900° C. It is important to note that the treatment at 1480°C in Ha produces a further purification from more volatile elements such as zinc, cadmium, arsenic, lead, and tin. Details on the preparation and characteristics of this type of very pure iron are given in a previous work.'' Only the complete analysis performed by neutron-activation methodsz3 is given here, Table I. Some of the specimens prepared in this way were carburized in the 0 region with very low amounts of carbon by treating them at 700°C in a static atmosphere of Ha containing a definite amount of CO. The set-up used is described in Fig. 1. A gas-tight quartz tube containing the specimen to be carburized and an internal friction control specimen, after being evacuated, was filled with Hz

Jan 1, 1963

By P. A. Witherspoon, S. P. Neuman

Evaluating the permeability of a caprock overlying a potential gas storage reservoir is a very critical problem. Pumping water from the reservoir can be used as an evaluation tool in analyzing this problem. Fluid level changes that occur in the aquifer us well as in the caprock can be measured with appropriately placed wells. If the leakage of water from the caprock into the aquifer is considerable, the effects will be apparent in the aquifer. If the leakage is slight, however, it will not be possible to detect it with certainty from observations in the aquifer alone. Fluid level measurements in the caprock must be relied upon. and improved methods of analyzing such effects have been developed which are based on a theoretical analysis of fluid flow through a caprock of infinite thickness. An example applying these methods to field data is discussed. INTRODUCTION One of the most critical problems in evaluating an aquifer gas storage project is determining the tightness of the caprock overlying the formation to be used as the storage reservoir. A formation that has previously held oil or gas obviously has a suitable caprock, but an aquifer that contains only water gives no such assurance. A number of aquifer projects in the United States have been troubled by gas leaking out of the intended storage zone, and the ensuing difficulties have led to the development of new evaluation methods. One of these new methods is pump testing wherein water is removed from the aquifer at some controlled rate prior to injection of gas. This fluid withdrawal causes a pressure drop to move out through the aquifer for considerable distances in a matter of days or weeks. Depending on the properties of the caprock, a pressure transient can also pass upward (as well as downward) through the caprock layers adjacent to the aquifer. Thus, if the operator has placed observation wells at appropriate distances from the pumping well, the rapidity with which the pressure transients reach different points in the system can be used to investigate the fluid transport properties of both the aquifer and its caprock. The usefulness of pump testing has been recognized by groundwater hydrologists for many years as a means of determining the potential yield and properties of aquifers used in water supply They have introduced the term "leaky aquifer" for a system in which an aquifer is overlain (or underlain) by semipermeable caprock layers. The ease with which water leaks into the aquifer during pumping can, of course, be very beneficial in bringing additional water to the pumped well. Hydrologists have therefore devoted considerable attention to this prob-lem. From the gas storage standpoint, however, the tighter the caprock layers that overlie the intended storage reservoir, the better are the conditions for minimizing or eliminating any vertical migration of gas. Thus, after a suitable geologic structure has been found, the emphasis in aquifer storage projects is in determining that the caprock is tight. Attention has recently been focused on the use of pump testing as one approach to solving this problem.23,24 This paper presents a further development on evaluating the permeability of a slightly leaky caprock when the caprock is of infinite thickness. From the practical standpoint, this means that the caprock layers are thick enough that pressure transients do not reach the outer boundaries of the system during the pumping test. In a subsequent paper, an analysis of the case where the caprock is of finite thickness will be presented. PREVIOUS WORK ON LEAKY AQUIFERS Jacob" developed a partial differential equation describing the flow of water in an aquifer of permeability k that is overlain by a leaky caprock of permeability k'. Fig. 1 shows a schematic cross-section of the system under consideration. One of his principle assumptions was that if k > > k', the direction of flow is essentially vertical in the caprock and horizontal in the aquifer. Neuman19 confirmed the validity of Jacob's assumption using a mathematical model. Another assumption was that a permeable source layer overlies the caprock (Fig. 1) and is able to maintain a constant hydraulic head at the upper boundary of the caprock. By neglecting the effects of compressibility within the caprock, Jacob1* developed a solution for a bounded circular aquifer. Later, Hantush and Jacobx5 used the same assumptions to solve the case of an infinite radial aquifer that is pumped at a constant rate. Their solution may be expressed in di-mensionless parameters by