Search Documents

By R L. Brathwaite

The orogenic gold deposits wall poster is one in a series of posters on different mineral deposit types being produced by GNS Science to raise awareness of the characteristics of New Zealand mineral deposits and their prospectivity. Orogenic gold deposits are typically quartz vein deposits formed in fault and shear systems at crustal levels within and above the brittle ductile transition zone, at depths of 3 12 km and temperatures from 200¦ to 400¦C. In New Zealand, orogenic gold deposits are found in regionally metamorphosed sedimentary rocks of Paleozoic and Mesozoic age. The deposits in Paleozoic rocks include those at Golden Blocks in Northwest Nelson, Lyell and Reefton on the West Coast, and Preservation Inlet in Fiordland. Quartz veins are developed along shear zones that dip steeply and generally strike parallel to the axes of folding in the greywacke and argillite/slate host rocks, although most are discordant to bedding. The lodes are typically less than 1 m wide and extend an average 200 m horizontally and vertically, but the Birthday Reef at Blackwater, Reefton, the largest quartz vein deposit in Paleozoic rocks, averages 60 cm in width and was mined over a strike length of 1070 m, and to a depth of 830 m. Disseminated gold occurs adjacent to the quartz lodes at Globe-Progress and some other Reefton deposits. The deposits in Mesozoic rocks are hosted in schist of Otago and Marlborough, and schist and greywacke of the Southern Alps. The lodes are typically lensoidal, less than 1 m wide and localised along single or multiple parallel shear zones that generally dip steeply, and are discordant to the schist foliation and bedding. A notable exception is Macraes, where the lodes are developed in the semi-concordant, low angle Hyde Macraes Shear Zone that has a strike length greater than 25 km.

Jan 1, 2005

By A Giblett, S Hart

"In 2015 operations under the ownership and/or management of all Newmont Mining Corporation subsidiaries (Newmont) produced 5.7 Moz of gold and 619 Mlb of copper from mining operations in five countries, with well over 100 Mt of ore processed by various grinding technologies. Processing methods used in the extraction of metals include flotation, oxidation, conventional cyanidation and heap leaching. The grinding technologies applied in milling operations feeding metal recovery processes include conventional wet grinding semi-autogenous grinding (SAG), rod and ball, dry grinding, concentrate regrinding and ultra-fine grinding, and ball milling of high pressure grinding roll product. SAG/ball (SAB) configurations represent the dominant comminution flow sheet within the company and the circuit configurations employed include SAB, SABC-A, SABC-B and single-stage (SS) SAG milling, with SAG mill feed ranging from run-of-mine (ROM) ore through to secondary crusher product. The collective experiences earned from designing, operating and debottlenecking these various comminution circuits provide many lessons that can be applied to the design and optimisation of future operations. This paper provides an overview of Newmont’s diverse comminution circuits, discusses recent performance and offers some insight into optimisation and design considerations based on recent experience in both endeavours.Citation:Giblett, A and Hart, S, 2016. Grinding Circuit Practices at Newmont, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 293–302 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By D J. Williams, A K. Kho, A Shokouhi, N Tucker

The disposal of dewatered coalmine tailings and coarse reject within spoil piles is gaining popularity as a means of eliminating separate surface tailings storage facilities or dams. The contrasting characteristics of coalmine spoil, coarse reject and tailings are somewhat complimentary, making the co-disposal of dewatered tailings within spoil piles geotechnically feasible and environmentally attractive. However, the impacts of mixing plant rejects within spoil piles are not well understood; in particular, the effects of water draining from the mixed plant rejects on the moisture content of the surrounding spoil. Changes in moisture content can cause additional collapse and degradation settlements of the spoil pile. A series of laboratory tests has been undertaken on mixtures of dewatered coalmine tailings, coarse reject and spoil. The results of these tests have been incorporated into a spreadsheet-based settlement prediction tool to investigate the effects of incorporating mixed plant rejects on total spoil pile settlements. This paper presents the laboratory tests undertaken, the incorporation of the test data into the settlement prediction tool, and settlement estimates for the various mixtures at different stages of construction.CITATION:Kho, A K, Tucker, N, Williams, D J and Shokouhi, A, 2015. Impact of co-disposing mixed plant rejects on spoil pile settlements, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 51–62 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

A study was undertaken to investigate the relationship between the quantity and value of economic demonstrated resources discovered for 12 mineral commodities over a ten year period and the expenditure required to yield such mineable resources. The results showed that for every dollar spent on exploration, there is an apparent in-ground average value of around $54 dollars contained in the economic resources found. While this appears to be a satisfactory return, it should be remembered that more than 99.9% of exploration programs are judged to be failures because a viable ore body or mineral deposit was not proved up. What is behind this seeming paradox?   The fundamental truth behind mineral exploration is the fact that the more you explore, the more you find, and that one success will often lead to further discoveries. It appears that one rich and viable deposit creates such surplus that its inherent high value ('the pot of gold') makes up for all the failures. In short, mineral exploration is a high risk business with uncertain returns. However, with skill, enthusiasm, experience and venture capital, it can yield larger than normal returns for the brave and the fortunate.   Analysis of exploration expenditure and economic resources discovered for the period 1987 to 1996 revealed that the apparent in-ground value of economic ore discovered per dollar of exploration expenditure varied from a high of $429 for iron ore and $261 for bauxite to a low of $22 for gold and for lead, and $5 per dollar of diamond exploration expenditure. Preliminary conclusions drawn on the reasons for the variations observed include the inherent ease or difficulty of discovery for different mineral commodities which may in some cases, relate to the natural prospectivity of Australia as a whole. Layered deposits like iron ore and bauxite appear to yield higher in-ground value returns on the exploration dollar. To some explorationists, this may be considered as seemingly obvious, but it may have more to do with very large-exploration tenement grants pursued by various Australian State Governments in the early 1950s and 1960s than the apparent ease of delineating a stratabound deposit.   Despite the apparent relatively low in-ground value produced by the gold exploration dollar of $22, the 5660 tonnes of gold discovered in this ten year period was worth $9.1 billion and representing over a quarter of the new mineral wealth created in the ten years to 1996. This contribution, along with that from the other minerals discovered over the period, led to a significant boost to Australia's export income and standard of living.   It is concluded that, given the nexus between the amount of mineral exploration expenditure and the quantity of new resources likely to be discovered, this knowledge may help policy makers seek to influence the rate of resource discovery in countries like Australia for the benefit of the nation.

Jan 1, 2004

This paper discusses the prediction of subsidence over partial extraction systems in thick coal seams. A model based on empirical techniques using influence functions is developed to calculate the surface ground settlements above extraction panels. Independent of the influence function, two field parameters, the subsidence factor and the angle of draw (limit angle) are required to define the model. Both these parameters are best observed from critical or super critical subsidence areas. However in thick seams, extraction widths are typically sub critical and therefore it was necessary to refine an estimation process for sub critical conditions. Partial extraction systems in NZ are characterised by variability with respect to extraction thickness and depth. As extraction proceeds along a panel, conditions deteriorate once the critical span width is exceeded and therefore percentage extraction decreases. A further variable was introduced to the modelling which allows for varying extraction sequences. Two comparisons with field observations, one over a partial extraction panel, the other over abandoned workings, showed the method gave good agreement to measured subsidence values.

Jan 1, 2002

Once and for all, the debate on the exponent in Gy's formula is pushed to its limit. It is explained why an exponent of 2.5, obtained when using a square root of nominal size d to adapt the value of a calculated liberation factor to a different comminution size, will rarely be encountered in practice, if no arbitrary decisions are made.

Mar 1, 2010

By T Barto, D Thomson, T Norgate, C Doblin

Collaboration between CSIRO Minerals and SunSalt Pty Ltd, a salt producing company located in rural Victoria, has resulted in a commercial process to recover magnesium sulfate (commonly called Epsom salt) from the saline waters of the Murray Basin. The feed for this process is bittern; the liquor remaining after halite (common salt) has been harvested from the saline water by evaporation.SunSalt produces salt and bitterns from three locations, namely Hattah (Victoria), Mourquong (NSW) and Wakool (NSW). The small size and considerable distances between these operations makes it uneconomic to build a stationary processing plant to extract value-added products, in particular Epsom salt, from the bitterns of the three operations. This fact led SunSalt to build a containerised mobile plant that could be moved to each site to process the bitterns at the end of the salt harvesting period.Epsom salt is extracted from the bittern by further evaporation, refrigeration and recrystallisation. In this process the bittern is diluted with five per cent volume of fresh water to minimise precipitation of residual halite in the bittern. Cooling the diluted bittern to between -5 and -10¦C precipitates up to 70 per cent of the magnesium sulfate, which is recovered as 85 to 96 per cent purity Epsom salt by filtration. This product is marketed as an industrial grade Epsom salt. Higher purity (up to 99.9 per cent) Epsom salt (USP or BP grade refined product) is made from the industrial grade product (raw Epsom salt) by recrystallisation.The containerised mobile plant was commissioned in December 2002. The raw Epsom salt generated in the mobile plant is refined to a higher purity Epsom salt in a separate plant located in Mildura. The Mildura plant was commissioned in December 2003.The CSIRO-SunSalt collaboration has demonstrated that the saline waters can be processed into a useful resource, and in addition could create jobs and a new skill base in regional Australia. The production of Epsom salt locally in Australia, which is worth currently about $A600 per tonne, removes the need to import over 3000 tpa from overseas with a net positive impact of $A2 million on the balance of trade.

Jan 1, 2004

Lime and cement manufacturing has a proud history in Otago, with the earliest lime kilns appearing around 1849 at Caversham and Kaikorai in Dunedin . At Dunback or Makareao (to be precise) three well-type kilns were built by the government in 1899. In 1909 these kilns were leased to the then Milburn Lime and Cement Company. They erected a large brick Schmatolla kiln in 1909, elliptical in plan and fired by coal gas. The kiln operated up until 1944 before being left derelict. The quarry which supplied the kiln also supplied the Burnside Cement works from 1929 up until its closure in 1988. The quarry was shifted to the top of the hill in the 1950s.

Jan 1, 1992

By E N. Isaev, L E. Levin

New data on the geology of the Late Jurassic to Holocene sediments cover of the World and associated mineral resources (oil, gas, ferromanganese nodules, ores of massive sulphides and other metals) have been compilled in the Atlas at scale 1:25,000,000 and 1:10,000,000. The work was performed by scientists from four Institutes of Russia (VNIIzarubezhgeologia, VNIIoceangeologia, Vernadsky Institute of Geochemistry and Analytical Chemistry of theRussian Academy of Sciences and Geological Institute of the Russian Academy of Sciences). The Atlas shows variation of thickness and formational composition of the large complexes (Upper Jurassic-Early Cretaceous, Upper Cretaceous Eocene, Oligocene-Neogene, Pliocene-Pleistocene), distribution of oil/gas and ore deposits in each complex, data of deepsea drilling (leg 1-130),  thermo-pressure condition in the sedimentary basins within Circum-Pacific Rim.

Jan 1, 1995

By J Zhou, D M. Hunter, S M. Iveson, K P. Galvin

The REFLUX Classifier is used to perform particle separations on the basis of density utilising a set of parallel inclined channels positioned above a vertical fluidised section. In continuous mode, feed enters part way up the vertical section, while fluidisation water is introduced from below. Lower density particles are conveyed upwards and collected in an overflow stream, while high density particles segregate onto the inclined surfaces, settle to the base of the system and empty via an underflow stream. Pressure transducers are used to measure the suspension density in the vertical section. This suspension density is maintained by a pneumatically controlled underflow valve to maintain a target suspension density or ‘set point’.Previously, Galvin et al (2010) demonstrated the significant improvement achieved via a new laminar-shear separation mechanism, achieved by utilising closely spaced inclined channels in the REFLUX Classifier. For the separation of low-density coal particles from mineral matter, a channel spacing of 6 mm proved effective; however, for the separation of gangue minerals from much higher density minerals such as iron ore, the shear-induced lift needs to be even higher. In this paper, we examine the influence of two different channel widths on the continuous processing of an industrial iron ore feed in the REFLUX Classifier. It was found that when moving from 6.0 mm to 3.0 mm channels, the ability of the system to reject coarser gangue material and retain finer high density material across a particle size range from 0.125 to 1.0 mm was increased, resulting in a higher grade product.CITATION:Hunter, D M, Zhou, J, Iveson, S M and Galvin, K P, 2017. Influence of shear rate on separation of iron ore fines using the REFLUXTM Classifier, in Proceedings Iron Ore 2017, pp 205–210 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By J Addai-Mensah, W Skinner, K Quast

The efficiency of any iron ore value-adding operation is closely associated with detailed knowledge of the mineralogy, especially in the processing of lower grade and complex ores. There are a number of physico-chemical properties of iron oxide mineral phases (eg goethite, hematite and magnetite) that can be prudently exploited to enhance their processing efficiency. Recent iron ore studies on the upgrading of high-goethite iron ores have highlighted that the knowledge of the various phases of both iron oxide and gangue minerals is critical to the economic processing of these ores. Appropriate knowledge of this kind can lead to better-designed flow sheets for economically viable production of saleable products. With the increasing use of goethitic materials as blend components of iron ore concentrates for steelmaking, this review paper focuses on relevant beneficiation processes and the pivotal role of mineralogy and petrology in producing saleable iron oxide concentrates from ore blends. For goethites, mineral impurities including silica, phosphorus and alumina are very important. Physical separations, as well as those incorporating higher temperatures, have also been included in this review as potential processes to upgrade high-goethite ores.CITATION:Quast, K, Addai-Mensah, J and W, Skinner, 2017. The importance of mineralogy and petrology on the beneficiation of iron oxide ores, primarily those containing goethite, in Proceedings Iron Ore 2017, pp 233–240 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By M Hernan

Bendigo Mining Limited has established a modern underground gold mine and processing plant at Bendigo in central Victoria. The Bendigo goldfield produced around 22 000 000 oz of gold between 1851 and 1954. Approximately 4 000 000 oz were sourced from surface alluvial workings with the remaining 18 000 000 oz won from underground quartz reefs. The modern mine is accessed via the Swan Decline, which commences at the Kangaroo Flat site on the southern outskirts of Bendigo and progresses in a north easterly direction between the Deborah and Sheepshead anticlines, reaching a depth of almost 1000 m below the City of Bendigo. Development of this decline commenced in 1998. Since that time 20 km of underground development has been completed. Exploration drilling, on-reef development and bulk sampling carried out between 1999 and 2005 resulted in the estimation of a Probable Ore Reserve of 700 000 tonnes at 9.0 g/t gold for 207 000 oz of gold. These Ore Reserves were contained within four reefs located on the Deborah and Sheepshead anticlines. Reef mining commenced in late 2005 from the Shywolup and Greater Garrard reefs. Material mined was stockpiled on the surface in preparation for commissioning of the process plant which commenced in mid 2006. Mining and processing were carried out between August 2006 and May 2007 during which time 176 000 tonnes were processed at an average grade of 5.4 g/t gold to produce 26 735 oz of gold. Plant feed was sourced from four reefs. This paper discusses some of the issues which were encountered with the definition and mining of these geologically variable and nuggetty reefs. This paper covers exploration techniques, grade estimation, mine geological control, mining methods, geotechnical issues and reconciliations. It will also discuss some of the lessons learnt and how these will be applied to future Mineral Resource and Ore Reserve estimation, as well as underground operations.

Jan 1, 2008

By M Z. Abzalov

Drilling mineral sand deposits has specific challenges, which are different from drilling hard rock deposits: Drilled sequences are represented by non-consolidated free-flowing sands to semi-consolidated clayey sands and indurated layers. Valuable heavy minerals (ilmenite, rutile, zircon, leucoxene) have an average density of 4.6 g/cm3, which is significantly heavier than the hosting sand matrix; mainly represented by quartz (density = 2.6 g/cm3). The large difference in the mineral densities can result in sample segregation in the drilling rods and capturing devices causing biased composition of the recovered samples. The drilled strata can contain beds of consolidated sediments, hard pan lenses and concretions. Therefore, chosen drilling equipment should be flexible and permit a switch from drilling the free-flowing sands to hard rock drilling. Thickness of the sand hosted mineralisation varies from several metres to more than 170 m. Mineralisation is distributed above and below the water table. Evaluation of the mineral sands deposits is based on hundreds of drill holes and many thousands of samples, therefore drilling methods should be fast and cost effective. The drilling methods commonly used for mineral sand deposit evaluation, include aircore, triple tube diamond and sonic; including its variants, such as vibrocore drilling technique. The ability of the studied drilling techniques to properly address the above listed challenges in mineral sand deposits, whilst maximising the quality of the obtained samples has been compared in three deposits: Corridor Sands (Mozambique), Richards Bay (Republic of South Africa) and Fort-Dauphin (Madagascar).This study has shown that aircore samples tend to be negatively grade biased, underestimating the heavy minerals content, in particular when drilled intervals are located below the water table. Triple tube diamond core method can produce non-biased samples. However, results can be marred by incorrectly chosen drilling mud. Sonic drilling is a relatively new technique based on a high frequency vibratory technology. It is the only production drilling technique that allows a continuous relatively undisturbed sample of unlithified sands to be obtained. The main limitations of this technology preventing its wider use for developing mineral sand resources are the relatively high drilling costs, in particular when the depth of drilling exceeds 100 m, and speed of drilling advance.

Oct 5, 2011

By I M. Howard

With the bell-less top (BLT) charging system replacing the centuries old double bell charging method, the furnace efficiency has been greatly improved together with considerable reduction in the furnace down time and operational problems. But still there are many draw-backs which need further attention to achieve better efficiency and operational effectiveness. The performance and operational problems of the BLTs have been highlighted and possible solutions to overcome some of the major problems are discussed.

Jan 1, 1999

In this paper the system of an operative expert estimation of innovative policy of mining enterprise technological development on sustainable development principles, created in the laboratory of economic analysis, planning and management of Mining Institute after D A Kunayev is represented. It is based on application of technology of satellite navigation and global positioning system (GPS). It allows to estimate the geotechnological complex functioning efficiency in the automated mode and on the basis of the obtained results to develop a complex of management measures on the competitiveness increase, realised by means of the automated corporative management system of geotechnological complex. The estimation of complex competitiveness is carried out on such basic aspects, as: technical, technological, organisational, ecological and economic as all of it give certain expenses and influence on complex overall performance. The major difference of the given approach is its realisation within the limits of the automated corporative management system of geotechnological complexes. It is based the fact that data of monitoring of complex's work will provide a sustainable development of geotechnological complex of mining enterprise.

Dec 6, 2010

By T Mattiske

The Fimiston Open Pit (commonly referred to as the æSuper PitÆ) is a part of the Kalgoorlie Consolidated Gold Mines Pty Ltd (KCGM) operation in Kalgoorlie-Boulder. KCGM manages the Fimiston Open Pit, the Mt Charlotte underground mine, the Fimiston Mill and the Gidji Roaster for its Joint Venture Owners, Newmont and Barrick Australia. KCGM produces up to 850 000 ounces of gold per year. The KCGM operations are located on the historical Golden Mile on the outskirts of the City of Kalgoorlie-Boulder, about 600 kilometres east of Perth Western Australia. This traditionally underground mining centre has been worked since 1893, yielding in excess of 50 Moz of gold from ore with an average head grade of 10 g/t. This represents approximately ten per cent of the gold produced in Australia and one per cent of the gold produced in the world. The Fimiston Open Pit is essentially an aggregation of what were known as the Judd, South, Paringa, Croesus/Eclipse, Central, Brownhill, Drysdale, Morrison, North and Horseshoe pits into one continuous large-scale operation. The old Fimiston Underground Operations (included the Main, Croesus, Chaffers, Lake View, and Perseverance shafts) were also located within the area of the Fimiston Open Pit. The underground operations closed in 1992 due to high mining costs.

Jan 1, 2002

Minerals Industry - 5 Year Outlook AusIMM sponsored project Positioning the Minerals industry for the 21st Century Does this seem right for New Zealand?  To ascertain the industry's perceptions of issues and capacity to address them: Industry context and issues Capabilities of professional staff Access to professional staff Balancing supply and demand Industry must do it. Cannot wait for others.   Some observations... Negative image - constrains capacity to influence community and government Major repositioning of professional staff competencies required Existing organisational arrangements and capabilities are under pressure to change Difficult to access professional staff of required capability Facing significant external challenges - with real concern about capacity to address them Prevailing culture not suited to needs of the future High level felt need for change The industry has a choiceà We can define where we want to be and act decisively Or We can respond to the future as it unfolds.

Jan 1, 2000

By W J. Cowie

Several years of operating experience of over 100 gold recovery operations on the West Coast has provided a database from which the basic operating costs of these types of operations can be characterised. Using figures generated from the averaging of plant operating costs throughout the region and financial modelling using Lotus spreadsheets has been developed to analyse both existing and proposed developments. This type of modelling has several uses: 1. Identification of the impact on profitability of changes in management practices, finance costs, operating costs and revenue streams. 2. Project evaluation and planning. 3. Profitability projections for development financing. 4. Troubleshooting with existing operations. 5. Valuation of existing operations and properties.

Jan 1, 1987

By D J. Brake

The correct specification and then selection of primary or major fans for an underground mine is a critical decision not only in terms of fan capital and operating costs, but also safety and reliability which usually has a major impact on mine production. In addition, fan manufacturers may spend tens of thousands of dollars preparing proposals for a purchase enquiry for primary fans especially where they have complete responsibility for the installation (turnkey projects). There are many good reasons to thoroughly and fairly adjudicate fan tenders. This paper describes the process to achieve this starting with the initial fan specification through to the final award.CITATION:Brake, D J, 2017. Fan specification and tender adjudication for mine ventilation engineers with particular reference to turnkey projects, in Proceedings Australian Mine Vent Conference 2017, pp 245–252 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

Phosphorus Phase Analysis of Medium-Low-Grade Rare-Earths-Bearing Phosphate Ores

Sep 13, 2010