Search Documents

By Jarc H

The steeply dipping silver/lead/zinc orebodies at Mount Isa mine have been extracted most recently by a combination of cut-and-fill and open stoping methods. Bench stoping was first used at Mount Isa Mine seven years ago to allow safe extraction of a highly stressed cut-and-fill stope. Subsequent benches have shown that the method offers significant cost and safety benefits through increased productivity and reduction in man exposure. The success of benching has lead to cut-and-fill mining being replaced at Mount Isa.Significant resources have been focussed to optimise benching. This paper describes the operational, planning, and research and development aspects which have contributed to the method to date. A brief look is also taken at the future direction of benching at Mount Isa.

Jan 1, 1992

By Brown A

An experimental evaluation of a selective agglomeration process in which an agglomerated coal rich phase was produced as a result of mixing light oil to various raw coal slurries is described. The beneficiation achieved by this method is compared to that obtained bv conventional froth flotation. The results suggest' that oil agglomeration is a more selective process than froth flotation and is less sensitive to variations in feed pulp density. Selective agglomeration has the additional advantage of producing a low moisture content product. The effect of replacing flotation filter cake with an equivalent amount of selectively agglomerated product in coke-making was studied with the aid of a pilot-scale coke oven. The results suggest that the principal effect of such a measure is to increase the bulk density of the charge.

Jan 1, 1977

The Canada Centre for Remote Sensing (CCRS) has developed an airborne sensor, the SWIR Full Spectrum Imager (SFSI) which detects in the short wave infrared range of the solar spectrum from 1220 to 2420 nm. In June of 1995, a demonstration flight was undertaken in the state of Nevada with the support of the companies listed above. The focus of the flight was to collect image data over well known mineral deposits with the objective of evaluating the applicability of this sensor to alteration mineral mapping. Some of the Nevada sites chosen include Cuprite and Goldfield, volcanic hosted acid sulfate systems; Yerington, a structurally complex porphyry copper deposit; and Virginia City, a quartz-sericite-pyrite vein system with advanced argillic pods. Ground spectral data was collected with the PIMA-II spectrometer. Solar reflectance calibration was done by Desert Research Institute personnel at Virginia City and Cuprite. This paper will discuss the configuration of the sensor and present image and ground data for Goldfield and Virginia City.

Jan 1, 1995

The maximum current density at which conventional copper electrowinning plants will result in satisfactory, adherent, and dendrite·free cathodes is determined by the thickness of the diffusion boundary layer. A decrease in the value of that thickness will permit an increase in the current density. This fact is utilized to develop a high current density cell in which the reduction of the boundary layer thickness is accomplished by means of a specially designed electrolyte circulation system. The high current density cell is used to determine the effect of current density on such process parameters as current efficiency, cell voltage, power consumption, and cathode purity. A number of empirical equations are developed for the purpose of estimating the magnitude of these effects.

Jan 1, 1972

By J Samosir, L Snyman

Northparkes was the first mine in Australia to use block cave mining method which relies on gravity and natural rock stresses to fragment and recover the ore. It was also the first hard rock mine to use hydraulic fracturing, in conjunction with CSIRO, to promote caving of E26 Lift 1. The technique was later used on E26 Lift 2 wedge and E48 prior to undercutting.Northparkes production is currently sourced from the E48 Lift 1 block cave mine and E26SLC. The E48 block cave contains economic ore to the north and south of the current cave footprint. To recover this ore the footprint has been extended on the north and south with two extraction drives and one extraction drive, respectively. Modelling of cavability above the additional drives indicated that the cave would not readily propagate to a sufficient height of draw to mobilise the ore and tended to arch over into the existing cave. To address the modelling results and to reduce the risk of the project, rock mass preconditioning was adopted.This fracturing campaign was performed from surface drill holes adjacent the subsidence zone angled to intersect the higher grade and higher elevation ore zones.Optical televiewer surveys, run prior to fracturing, picked intervals and fault zones to be avoided. Holes were resurveyed post-fracturing to detect newly created fractures and as a measure of success of the program.During fracturing operations water and gel fractures were run at varying depths and pumping pressure was logged for each fracture. The mine seismic system monitored significant events and dye in the fluids utilised for tracking water inflow locations during underground inspections.Towards the end of the project, guar fibres from gel were detected within the mill circuit and required treatment to resume optimum processing.CITATION:Webster, S, Snyman, L and Samosir, J, 2016. Preconditioning E48 cave extension adjacent to an active cave, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 471–478 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Gordon DM

Tyres account for 25-30 per cent of the operating costs of large capacity haul units as used in open-cut mines.Tyre operating costs can be substantially reduced and often contained in real terms by applying knowledge that is now available.This paper describes certain specific advances in tyre management, namely batching, bias adjustment, cumulative plotting and the so-called "pressure-temperature" system of tyre pressure control, originated on the Mt Newman Mining Company's Newman minesite, and discusses the contribution that each has made to improving tyre management and reducing costs.

Jan 1, 1983

By R Osterman

As mining companies have to go deeper in search of ore and coal, the importance of protecting the highwall increases. Wall fatigue also increases with importance of the long life expectancy of a highwall, in particular the impact of fatigue influenced by resonance. Resonance is the tendency of a material to oscillate with greater amplitude at certain frequencies when exposed to a periodic force. Until recently, only dominant frequencies, either natural or induced, were all that could be measured through the fast Fourier transform of the blast-induced wave form.This paper presents a novel method to accurately predict the resonant frequency of a highwall. In fact, the method can predict the natural frequencies between any two monitoring points placed in line with the source of impact, and as such it can be used to determine the resonant frequencies of any physical object. The method not only predicts the resonant frequencies of the material; it predicts the structural response of the total frequency spectrum. This method helps describe the response of a mechanical structure to excitation. It describes the structure’s efficiency in the use of energy, that is, whether energy is dampened or consumed in resonance.The initial predictions have been so accurate that it made it possible to determine the fundamental frequency and the first six harmonics of a highwall in a northern Queensland coalmine. With the use of electronic detonators, the blast can be timed with a repeating delay to create an induced artificial frequency that has been determined to retain the least amount of energy.CITATION:Osterman, R, 2015. Transfer function – new method to accurately predict resonant frequencies of a highwall, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 233–244 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By D A. Cuello, G B. Sharrock

The Prince Lyell orebody at Mount Lyell Mine has a rich mining history commencing with the open pit in 1935, which transitioned underground in 1972. Between 1972 and 2014 a total of 64 Mt was mined underground as the mine extended from 210 m to 1100 m below surface. As the depth increased, three separate transitions in the mining method occurred to meet the changing geotechnical conditions, ore grade, mining costs and metal prices. The first was open stoping with pillar recovery in 1972, followed by front caving and longitudinal sublevel caving (1995), and finally transverse sublevel caving (2004 to 2014). This paper provides an overview of key geotechnical and planning milestones relating to the evolution of the mining method including underground stability, gravity flow, cavability and subsidence. Key aspects of the mine design, geotechnical parameters and rock mass response are described and critiqued with reference to observational, numerical and empirical methods.CITATION:Sharrock, G B and Cuello, D A, 2016. Geotechnical milestones at Mount Lyell Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 427–438 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

THE township of Costerfield is situated in the parish of Costerfield, county of Dalhousie, and lies 6 miles east of Heathcote and 30 miles south-east of Bendigo. It is separated from Heathcote by the Mt. Ida Range, which forms the western boundary of the Silurian formation. It is situated at the head-waters of Tin-pot Creek, a small southerly tributary of the Deegay Ponds Creek, which flows east to the Goulburn River.The field was discovered in 1860 by two prospectors, Coster and Field, who were guided there by a shepherd, M Nicol Coster and Field had already discovered an antimony lode about three miles nearer Heathcote, when M Nicol offered to guide them to the larger outcrop. The main Costerfield reef at that time projected above the surface, and was white through oxidation, though the bluey sulphide showed on fracture. No alluvial gold of any consequence was obtained at Costerfield, but a little was obtained, at Redcastle, 7 miles to the north, and in some of the gullies to the east.Following its discovery there came a period of prosperity to Costerfield, while the mining operations were confined to the oxidized zone. The early success of mining at Costerfield was due to the gold values, and it is probable that the oxidized zone was secondarily enriched. The earliest available record of values is a crushing of Coster and Co. on the Antimony reef (now known as the Costerfield reef), when 200 tons from a depth of 70 ft. averaged 4 oz. per ton in July, 1861. At this time a crushing mill had not yet been erected at Costerfield, and the ore was carted and treated at Redcastle. The massive antimony ore, consisting of mixed oxides and sulphides, was separated by hand-picking as "marketable ore," and the remainder crushed for gold. A higher average is recorded from South Costerfield in September, 1861, when a 15' cwt. parcel...

Jan 1, 1922

By E Selvapandian, R Barr

Arrium (previously OneSteel) initiated a desktop study into the performance of its hematite ore beneficiation plant in early 2010. The beneficiation plant utilises jig concentrators and spirals to upgrade low-grade hematite recovered during mining at the Iron Duke (ID) mine site located 60 km south-west of Whyalla. The study, conducted in conjunction with Mineral Technologies, identified a number of opportunities for improvement, which were validated by a series of sampling campaigns and a pilot plant trial. One of the major recommendations was to upgrade the ultra-fines processing circuit from a single-stage spiral circuit to a three-stage circuit. The upgrade of the ultra-fines circuit was estimated to provide a significant increase in fines production and grade.In order to capitalise on the strong iron price at the time of the project, Arrium decided to utilise a fast-tracked approach to design, construct and commission the processing equipment required to achieve the improvements identified. This decision introduced the risk of missing critical steps in the project development process, which could have potentially resulted in major issues in latter stages of the project. In addition to the challenges introduced due to the expedited time line for project completion, this project presented unique challenges due to its brownfield nature. One such challenge faced was the integration of the new equipment and control system software.Furthermore, the importance of the ID ore beneficiation plant (OBP) contribution to the companyÆs export commitments meant the upgrade work had to occur while minimising disruption to normal operation. This decision presented a set of new challenges to an already complex project. One such challenge was the need to build and commission the new spiral circuit in isolation from the operating plant.The aim of this paper will be to highlight some of the challenges faced in a complex brownfield project such as the ID OBP upgrade and discuss how they were managed to enable the successful commissioning of the process in early 2012.CITATION:Selvapandian E and Barr, R, 2013. Managing challenges faced in the brownfield commissioning of an ultra-fine hematite processing circuit at ArriumÆs Iron Duke ore beneficiation plant, in Proceedings Iron Ore 2013 , pp 533-538 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By B R, R Brooks, R Simcock, R Stewart

As environmental costs incurred by the mining industry become increasingly subject to critical analysis, new technology is necessary to ensure the further development of good relationships between the industry and community. Phytoremediation and phytomining are technologies that have the potential to capture the imagination and approval of the public. Phytoremediation , the in situ use of plants to extract heavy metals from a contaminated substrate, could offer an environmentally and cost-friendly alternative to traditional remediation techniques. Phytomining is the in situ removal of metals from a contaminated site or subeconomic orebody with the additional aim of recovering from the plant an economic amount of metal. Plants used in such operations, hyperaccumulators, accumulate large quantities of one or more target metals in their above-ground herbage. Upon harvesting and incineration, this plant material yields a low-volume, sulphide-free æbio-oreÆ, which can either be safely disposed of, or if the metal is of sufficient value, smelted. Investigations into the economics of phytomining nickel from ultramafic (serpentine) soils, showed that Alyssum bertolonii and Berkheya coddii could remove over 100 kg of nickel per hectare per annum from land with nickel concentrations well below the cut-off grade for conventional mining. It also appears possible to æinduceÆ the hyperaccumulation of gold into plants growing on gold tailings, or on stockpiled, low-grade gold ore. The plants used for phytoremediation and phytomining are useful colonisers as they are necessarily hardy and withstand extremes of salinity, metal toxicity and water stress that hinder the success of current revegetation procedures. As part of a rehabilitation operation, these plants may alter the geochemistry of a substrate making it more amenable to the growth of native species that should be used to restore a mining site to pre-operating conditions.

Jan 1, 1999

(This paper reviews the reasons for and the principles followed in designing and constructing complete new surface works at the mine of the Zinc Corporation Limited, Broken Hill, New South Wales, and describes the layout, plant, buildings and services.)The Zinc Corporation mine produces high grade lead, silver and zinc sulphide ore. Lead and zinc concentrates are sent by rail to Port Pirie, where the lead is smelted and the zinc concentrate is shipped to Tasmania, England and other overseas countries.Some time ago consideration was given to the advisability of sinking an additional shaft. For some years the old main shaft had been working at full capacity and developments underground had indicated that the mine would eventually be capable of an output greater than that which could be handled through the shaft. It was therefore decided to sink a new main shaft and the site chosen was in footwall country 900 feet south of the old main shaft. The reason for the move south was so that the new shaft would be opposite the centre of gravity of the ore-bodies at depth. The size of the new shaft is 27 ft. ,6 in. x 15 ft., and the work was put in hand early in 1936.It was intended to haul the whole mine output through this shaft, which was 1,600 feet from the mill then operating. An extensive conveyor system thus became necessary unless a new mill was built near the shaft. A careful study of the situation was made by the management and consideration was given to requirements for expansion, the condition of...

Jan 1, 1940

By P M. Ashley

Antimony (Sb) is an element similar to arsenic that forms anions in surface waters, rather than cations like other metals. Little is known about natural mobility of antimony in the environment. However, recent studies have suggested that antimony has similar toxicity to arsenic. Current New Zealand drinking water guideline values are 3 parts per billion (0.003 mg/l) for antimony and 10 ppb (0.01 mg/l) for arsenic. Antimony occurs principally in stibnite (Sb2S3) in mesothermal vein deposits hosted in low grade metamorphic belts of eastern Australia and southern New Zealand. Many deposits have been mined historically, including one large deposit, at Hillgrove, NSW. Oxidation of stibnite and associated arsenopyrite and pyrite causes local acidification of natural waters but acid is readily neutralised by carbonates in mineralised zones and host rocks, and therefore waters are near-neutral (pH 6-8.5). Antimony dissolves readily in moderately oxidized, near-neutral waters. Experimental stibnite oxidation yielded up to 37 mg/kg (37 000 ppb) dissolved antimony, and mine and tailings dam waters at Hillgrove mine have up to 55 mg/kg (55 000 ppb) dissolved antimony. Natural stibnite can contain >5000 mg/kg arsenic in solid solution and therefore dissolution of stibnite, arsenopyrite and arsenian pyrite also releases arsenic into waters. Resultant dissolved arsenic concentrations are up to 3.6 mg/l (experimental) and up to 7.2 mg/l (mine and tailings dam seepages). Mine and tailings discharge waters have elevated antimony and arsenic where they emerge, but attenuation occurs by deposition of the metals on to amorphous iron oxyhydroxides which can contain >10% each of antimony and arsenic. Historic disposal of mineralised waste rock and tailings into the stream system at Hillgrove has caused contamination of sediments and waters with antimony and arsenic for at least 20 km downstream with effects traceable in sediments for 300 km. Other stibnite-bearing deposits are likely to have analogous environmental effects, particularly from historically-mined sites.

Jan 1, 2002

By T Haskell, Y Joe, S Dickie

A current trend amongst producers is the increase in dewatering of iron ore fines (<0.5 mm), due to an increase in wet beneficiation processes used to upgrade lower quality ore deposits, increased water content in orebodies located below the water table, and increasing focus on transportable moisture limits (TML). Vacuum filtration is commonly used for dewatering of iron ore fines, and as with all filtration processes performance decreases with particle size. Significant improvements are possible with the use of filter aids, usually anionic surfactants and flocculants. Anionic surfactants reduce the surface tension of the associated water, which is then removed more readily leading to improved filtercake moistures. Anionic flocculants used correctly can improve cake permeability, in turn, decreasing cake formation times and increasing filtration rates. In addition to increased throughput, savings and benefits for producers can include: moisture limit penalties, improved handleability, along with energy and water savings.The effect of filter aids on two iron ore fines samples from the Pilbara region were evaluated using a lab scale vacuum filtration unit. The first sample showed a reduction in the filtercake moisture content by 2.3 per cent weight/weight (w/w) with the use of BASF’s Drimax® 1234. For the second sample a reduction in the filtercake moisture of 3.4 per cent w/w along with an increase in filtration rate of 20 per cent was achieved by using a combination of Magnafloc® 5250 and Drimax® 1239 NF, as both filter throughput and cake moisture were considered important by site.CITATION:Haskell, T, Dickie, S and Joe, Y, 2017. The use of filter aids on iron ore fines, in Proceedings Iron Ore 2017, pp 183–186 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

It is easy to demonstrate the importance of aggregates in any conversation about infrastructure and other engineering artefacts. Peoples around the world have made use of stone to enrich and enhance their lives since the earliest days of civilisation. In New Zealand, Maori used hard durable rocks for weapons, tools, and basic structures. European settlement accelerated the use of quarried materials and formed the basis for development of our society as we see it today. Logic might suggest that the quarrying sector would be recognised positively for, and encouraged to continue to contribute to, this underpinning of the way we are. The reality is æNot In Most Back YardsÆ. Why? The rock is where it's always been (often overlooked) and our æsocialÆ environment is today's hard place. For a resource-based business in New Zealand, that environment is principally the Resource Management Act, with the widespread power it has distributed to anyone prepared to invest their time. This coupled with a lack of leadership and direction in the implementation of the Act has created a climate that stifles development and diverts energy and resources to æplaying the gameÆ rather than ælifting the gameÆ. Perhaps the real costs of this are not yet widely recognised. The paper will draw mainly on the experience of endeavouring to consent a ægreenfieldÆ quarry in the Waikato region. This is supported by commentary based on nearly 10 years of ælivingÆ with the RMA at sites across much of New Zealand. RMA Scorecard Summary: Effects based? Rarely. Level playing field? No. Maori Consultation? Could do better. Efficient use of resources? No. Timely? No. Is it working for other sectors? Certainly not the quarrying industry's customers and end users.

Jan 1, 2000

This paper describes the methods of constructing timber barricades against pillars of ore in the South Mine, property of Broken Hill South Limited, Broken Hill, N.S.W., and discusses the behaviour of the various types of barricade alongside trucked sand filling and hydraulic stowed sand filling.Since the introduction of hydraulic stowing, cut and fill and overhand square letting methods have been used in mining the pillars. Such methods could not be used where the pillars had failed badly. The filling used is partially deslimed concentrating millresidue containing among other gangue minerals, calcite and a small amount of pyrrhotite and pyrite.The author is indebted to the mine superintendent of Broken Hill South Limited for permission to publish this paper.OLD METHODS OF CONSTRUCTING BARRICADES.Square Set Stopes.Before filling each stope the outer row of legs was lined inside with 10 in. x 2 in. boards spaced 2 in. apart. It was usual to tie the row of legs and caps together with timber dogs. As the space between the barricade and ground varied from nil to several feet, it was general practice to fill behind the lining boards. No provision was made to retain this sand during subsequent pillar stoping, consequently a run of sand right up the barricade could cause adilution of ore and serIOUS dIstortion of the barricade.

Jan 1, 1946

By X Zhang, B McFadzean, P E. Ngoepe, B Nemutudi, P P. Mkhonto, S Pikinini

There is still a huge challenge in efficiently recovering the arsenides minerals that are largely concentrated in the Platreef Bushveld Complex which constitutes about 21 per cent of the platinum group minerals (PGMs). Therefore new collectors are required to improve the recovery separation of hard to float minerals, in particular sperrylite. The triazine modifications are promising reagents for mineral flotation and have not been given much attention in minerals processing. The adsorption of sodium 2,6-dithio-4-butylamino-1,3,5-triazine (SDTBAT), sodium 2,6- ditrithiocarbonate-4-butylamino-1,3,5-triazine (SDTTCBAT) and sodium normal butyl xanthate (SNBX) on sperrylite (100) surface were performed to identify a well performing collector molecule. We observed that the triazine collectors preferred to bridge on surface As and Pt atoms through the S atoms. We found that the adsorption energies were in the order: SDTTCBAT > SDTBAT > SNBX, indicating that the SDTTCBAT had strong exothermic adsorption on sperrylite and pyrite. These results showed that the ditrithiocarbamate had a great influence in the adsorption strength on the sperrylite surface. Importantly it was found that the triazine collector had stronger adsorption than the xanthate, which portrayed a promising replacement of xanthate collector. These results paved a way for design of novel collector for sperrylite and other chalcogenide minerals to improve their recovery.

Aug 24, 2022

By J D. St George

Flyrock is the unexpected and undesirable projection of rock fragments during detonation of a blast and managing this risk is becoming an increasing challenge as urban development encroach toward mineral extraction sites. The basic factors associated with flyrock are discussed in relation to geology, blast design and management. Published data of historical flyrock events are investigated and compared with local information on incidents. Good agreement was found between the data sets. A computer program of flyrock was developed using projectile motion based on launch velocity and angle, rock size, shape and density. This deterministic model was coupled with a probability model to simulate blast events. The impulse time ?t of the explosive pressure was taken as the stochastic variable to replace launch velocity. The variables were calibrated to replicate field data. A simulation was executed to demonstrate the capability of the approach to defining flyrock danger zones. For a simplistic situation it was identified that an appropriate distance to be cordoned off for the blast danger zone is a radius of 120 m in front of the blast and 65 m behind.

Jan 1, 2001

By K Niiranen

Luossavaara-Kiirunavaara AB (LKAB) operates one iron ore mine, three concentration plants and three pelletising plants in Kiruna, Sweden. The current methods of separation at the beneficiation plants are low intensity magnetic separation (LIMS) and reverse apatite flotation, where the wet LIMS stage is regarded as the crucial part of silica separation from the ore. Because future silica levels are expected to increase in the incoming material to the beneficiation plants, geometallurgy has become an important area of development and research.A laboratory-scale methodology was developed for the systematic characterisation of the ore for mineral processing, with the focus on the high silica ore type B2 and newly discovered subtypes. This methodology combines mineralogical, geochemical and process mineralogical characteristics. Automated mineralogy (QEMSCAN®) is used to study the modal mineralogy, the distribution of silicate minerals in different particle size classes after comminution, the deportment of silicon (Si) between various silicates and the degree of liberation and intergrowth of magnetite and silicates. An essential stage in the systematic characterisation of the ore deposit for mineral processing is the estimation and simulation of different parameters from the laboratory scale to the full scale at the concentration plants. This is achieved by using empirical models based on the data collected at the mineral processing plants. As the first step to implement the geometallurgical information, the current geological model is reconstructed with the mineralogy and the two, newly defined subtypes of high silica ore type B2 are separated into different domains.To study the reduction of the SiO2 content in the magnetite concentrate, a large-scale reverse cationic silicate flotation laboratory test program was initiated in early spring 2016. This program investigated potential silicate flotation in the beneficiation plants at the Kiirunavaara site. The second target is to implant mineral processing parameters into the block model based on the new geological model. This information provides a good basis for making a prognosis for mine planning and a quality prognosis regarding the crude ore for mineral processing.CITATION:Niiranen, K, 2017. A geometallurgical perspective on a high-grade iron ore deposit at Kiirunavaara, northern Sweden, in Proceedings Iron Ore 2017, pp 309–318 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By D Brett

"Mine waste storages including tailings dams and waste rock dumps represent arguably the biggest risk on a mine site from both physical and geochemical viewpoints, related firstly to structural stability and the consequences of failure and secondly from potential on-going seepage or run-off of acid and metalliferous drainage (AMD). The risks are most likely to increase during operations and continue through the closure and post-closure phases, with the waste storages likely to be the most difficult features to resolve in the mine closure process. Contaminated water quality from tailings dams and waste rock dumps can require treatment "in perpetuity" at a cost of hundreds of millions of dollars. The problem is increasing with ever larger mine operations and waste generation volumes. This paper identifies leading practice methodologies in planning and operating mines and process plants to minimise the risks from tailings storages and how this might also affect waste rock management and even the design of mine excavations. These methodologies require a "big-picture" approach to develop an understanding of the overall issues and identify synergies between the different operational areas on a mine site that can reduce overall risk. With a conservative approach and realistic allowance for future costs it is possible to facilitate decisions at the mine planning stage that can reduce risk and save cost over the long term. This is in contrast to the common approach where each operational area is looking to minimise its own costs with a short-term view. Incorrect mine methodologies can be developed by allowing net present value (NPV) accounting methods to trivialise future closure issues.Methodologies discussed include: Integrated Waste Management - Significant structural improvements to tailings dams can be achieved if the structures can be incorporated into the waste rock dumps. Risk of AMD can also be reduced by utilising the tailings and waste rock effectively. This could go even further to consider the placement of wastes to limit mine void environmental issues; Process Optimisation - Water quality and the nature of potential tailings dam structures can be highly influenced by the geo-chemistry of the tailings. This can be modified by processing, where simple changes such as maintaining separate streams of geo-chemically different tailings rather than recombining them or by initiating further processing to remove problematic minerals such as sulphides; Enhancing Geophysical Properties - The geochemical performance of waste repositories can be greatly influenced by the geophysical properties of the stored materials, particularly the air-water characteristics, which are influenced by particle size, density and permeability. The geotechnical properties can be enhanced by strategic paddock dumping, blending and compaction.These methodologies are demonstrated by case histories.CITATION:Brett, D, 2013. Mine waste risk minimisation by integrated waste management and process optimisation, in Proceedings MetPlant 2013, pp 247-258 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 15, 2013