Search Documents

By J Joy, A Bye, G V. Kizil

This paper demonstrates an application of a recently developed Risk-Cost-Benefit (RCB) Framework to environmental risk management in the mining industry. The environmental application of the RCB Framework as part of an ACARP project (Kizil, Bye and Joy, 2012) involved a thorough selection process with site visits and in-depth discussions with the case study siteÆs environmental management team. Under their guidance, the highest risk of environmental impact at the case study site was identified as æroad subsidenceÆ at the time when the project work was undertaken. This paper presents the unique application of the RCB Framework to examine the risk of mining-induced subsidence and its impact on one of AustraliaÆs busiest highways, with a traffic volume of 38 000 vehicles per day (NSW RTA AADT, 2008). The RCB Framework was employed to assess the optimum group of controls for road subsidence risk management to ensure highway availability while mining occurs. Whilst this paper focuses on road subsidence, the methodology employed can be directly applied to other environmental concerns including preparation for mine closure, rehabilitation planning and waste management. The RCB Framework incorporates mathematical modules which were developed to enable complex yet tightly integrated RCB calculations. The process integrates the risk-control effectiveness assessment to determine that the selected safety initiative is financially beneficial to the mine site and company. This concept has been applied to a number of high-risk mining areas targeting safety, productivity and environmental issues. This paper introduces the five-staged RCB Framework, incorporating the RCB tools RCBGEN (Risk-Cost-Benefit Generator) and RCEMETHOD (Risk-Control-Effectiveness Method), and demonstrates its practical application to the risk management of a road subsidence case study. The case study looks at potential pavement damages, in particular, the occurrence of pavement stepping on the surface of the highway as a result of vertical subsidence. This type of road damage was previously experienced at another major inter-city route while underground mining occurred in the region where the case study site is located. The RCB Framework has been successfully applied to the analysis of the road subsidence case study and determined the risk reduction and financial benefits of implementing a range of risk-controls. User-friendly RCB Charts to provide an aid for decision-making were produced. The value of using the RCB charts to achieve balance between risk, cost and productivity in the decision-making process for risk management has been explained. The case study determined that pavement slots and fibre-optic cable monitoring were relatively low-cost and effective controls applied in the mining industry for the first time at a global level.This paper supports the industryÆs ongoing efforts to manage risk to ALARP (as low as reasonably practicable) and achieve æzero harmÆ by providing a new Framework to more effectively establish the adequacy of controls.CITATION:Kizil, G V, Bye, A and Joy, J, 2012. Application of risk-cost-benefit analysis to highway subsidence due to mining, in Proceedings Life-of-Mine 2012 , pp 197-206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By T Ma, F T. Suorineni, Q He, J Oh

Directional hydraulic fracturing was invented by Polish experts and was first applied in coal mining to prevent hard roof rock bursts. Based on its successful application in coal mining, directional hydraulic fracturing has the potential to reorientate the hydraulic fracture trajectory. Recently, this technique has been introduced into cave mining for the purpose of lowering breakdown pressure. The hydraulic fracture is much easier to initiate with the assistance of an initial notch. No systematic theoretical or experimental studies have been carried out to investigate the influencing factors in the hydraulic fracture reorientation process. In this paper, the numerical modelling software Realistic Failure Process Analysis3D (RFPA3D) – Flow Version is used to study the influence of the in situ stress condition and rock mass heterogeneity on directional hydraulic fracturing in brittle heterogeneous rock masses. Firstly, the reliability of RFPA3D in simulating hydraulic fracturing is validated by comparing its results with experimental results and the simulation results from the extended finite element method. The hydraulic fracture trajectory is then observed in a three-dimensional stress environment. The results indicate that for the in situ stress condition, when the borehole lies in the ?2–?3 plane, only the difference between ?2 and ?3 has an important influence on hydraulic fracture reorientation. Furthermore, rock mass heterogeneity is a key factor that must be accounted for when fracture reorientation is required.CITATION:He, Q, Suorineni, F T, Ma, T and Oh, J, 2016. Modelling directional hydraulic fractures in heterogeneous rock masses, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 369–384 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By R Wei, Y Peng, D Seaman

This study addresses a widespread problem confronting the mining industry: the deleterious effect of clay minerals in flotation. This problem is seemingly exacerbated by the presence of iron contamination from grinding media. The interaction of clay minerals and grinding media in copper and gold flotation was investigated in this study. A low-clay ore and a high-clay ore were obtained from Telfer to represent different contents of clay minerals, while stainless steel and mild steel grinding rods were used to produce different grinding chemistry, in particular, iron contamination. Flotation tests on an unsized and sized basis were conducted to reveal how clay minerals and grinding media affect copper and gold flotation. Iron contamination and the oxidation of copper minerals were quantified by ethylene diamine-tetra acetic acid (EDTA) extraction. It is interesting to find that both clay minerals and iron contamination depressed the flotation primarily in fine particles smaller than 33 ¦m, and clay minerals played a dominant role. Although flotation of coarser particles greater than 33 ¦m was less affected by clay minerals and iron contamination, coarser grinding to increase P80 was not an effective way to improve copper and gold flotation for the high-clay ore. This study suggests that to improve copper and gold flotation from clay ores, clay dispersion in conjunction with the minimisation of iron contamination may be required.CITATION:Wei, R, Peng, Y and Seaman, D, 2013. The effect of grinding media on copper and gold flotation in the presence of clay minerals, in Proceedings World Gold 2013 , pp 283-288 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By P Jere

Mechanically coupled rock bolts encapsulated in cementitious or polyester cartridge resin grouts have been widely adopted for various underground rock reinforcement applications. Resin grouts are considered a superior product, however, both systems have their advantages and limitations, with the relative performance, quality installation cost and cycle time as the most notable parameters. Both applications have optimal rock bolt combinations and preferred ground conditions. Cementitious grouts are favourable for use with secondary deep embedment anchors. These are installed using various equipment with a series of autonomous tasks required to complete the installation cycle. The cartridge resin system can be utilised by a bolting or face boring rock drill to complete the full support installation cycle. This reduction in equipment changeouts mid-cycle generally deems it the more practical application and popular choice for primary support. Self-drilling anchors (SDAs) and hollow bolts have been a viable alternative to traditional rock reinforcement in variable and challenging ground conditions. Using a pumpable post installation grouting system, SDAs have proven to aid the quality of installation, but due to the additional equipment and cycle steps associated with application, the cycle time is increased. In recent years, fully mechanised bolting equipment designed to utilise a combination of self-drilling anchors and a thixotropic pumpable resin installed in a single pass has entered the market. This innovation is anticipated to deliver the advantages described above, with fewer limitations, and significantly improved development and rehabilitation rates. St Barbara Mining and Byrnecut Australia, supported by Master Builders Solutions, were first to conduct extensive trials and implement this rock bolting approach in an Australian hard rock underground mine and record the actual performance.

Mar 29, 2023

By R Norris, M Dunne

Substantial efforts by the industry, as well as by process and equipment designers, have resulted in many innovative developments that provide cost effective reductions in water usage. This paper showcases four emerging best practices in industry including examples of recent installations. Belt press filters are a small fraction of the operating and capital cost of alternative ædryÆ tailings technologies. This gives operators who must ædryÆ their tailings a competitive advantage and makes such operations much more sustainable. The new generation of belt filter presses use less energy, produces lower cake moistures and better disposal stacking properties. The need for tailings storage facilities may be eliminated or in some cases high-grade tailings can be dewatered and sold as a low value product. Mining applications include sand tailings, sinter plant waste, coal tailings and power station fly ash. Flip-flow screening machines are proven worldwide in the dry classification of coal and other minerals, reducing the size of beneficiation plants, whilst reducing energy, water demand and media consumption. They also allow the screening of wet/sticky materials not able to be sized using conventional screens. Lamella separators are used for toxic water clarification and/or sludge thickening in many downstream metal industries with the underflow often dewatered in a belt filter press. Such low cost, high capacity thickeners could also be used instead of conventional thickeners at smaller mines. The simple and reliable continuous washing upward flow (CWUF) sand filters have been used for treatment of waste water from coal preparation plants and steel works as well as in the production of potable water. The filtered waste water from mining processes can then either be reused or discharged from site. Other installations include cleaning mine water to prevent the blocking of dust suppression spray nozzles.

Jan 1, 2006

By M P. Sandy, R M. Stephenson

Portals to access underground mines are important infrastructure and their design requires careful consideration. Portals are generally expected to last for the life of the mine. Typically, the exposure of personnel and equipment is high, with many hundreds of movements through the portal per day. Consequently, the risk associated with geotechnical instability must be extremely low. Portals are often established from a boxcut. In areas where the weathering profile is well developed, the design and execution of the boxcut can involve significant effort, with the objective of minimizing the volume of the boxcut, whilst ensuring that conditions at the design depth are suitable for establishing a stable portal. Properly designed site investigations are a critical part of this process. Currently available portal design guidelines have not been updated for decades, however the equipment and ground support systems have changed significantly in recent years. Many mine portals have since been constructed in a relatively short time frame with success, often in challenging ground conditions using some of the more modern approaches to ground support. This is beneficial because delays in establishing a portal will generally delay other critical path activities, and lead to cost overruns.

Mar 15, 2021

By A Remes, A Dennis, M Talikka, T Kotiranta, S Horn

A mine project combines vast amounts of information from various disciplines including but not limited to geology, mining, metallurgy, technology, environment and economics. In many cases, all relevant information is not fully shared between all disciplines. Thus, project performance (technical, economical and sustainability) may be evaluated on basis of insufficient information resulting in non-optimal decisions, project execution and risk management. Advances in computing power and simulation software enable various data sets to be incorporated in a single digital platform enabling more efficient and transparent data sharing. In addition, linked data sets and simulation can support assessment and optimization of the project as a whole rather than focusing on optimization of individual events. CITATION:Horn, S, Remes, A, Kotiranta, T, Talikka, M and Dennis, A, 2018. Evaluation of sustainability of copper production value chain from ore to metal using advanced simulation, in Proceedings Life-of-Mine 2018, pp 87–89 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By S M. Jowitt, G M. Mudd

"The mining industry is the source for the vast majority of the metal, mineral and energy resources we use on a daily basis. New deposits are discovered over time and are developed into mines before being rehabilitated – a sequence that when repeated can help contribute to the noble notion of ‘sustainable development’, despite the generic concept of mining being the unsustainable consumption of non-renewable resources. The scale of the modern mining industry is immense – from iron ore and coal to base and precious metals, modern mines are sometimes hundreds or thousands of times bigger than their long lost historic ancestors. We also live in a world with emerging and increasing demands for so-called technology metals (aka ‘critical’, ‘e-tech’ or ‘specialty’ metals) that are needed to feed the rapid growth in renewable energy (especially solar photovoltaic panels and wind turbines), consumer electronics, sophisticated military technologies and super alloys, amongst other uses. These elements include the rare earth elements, indium, germanium, tellurium, rhenium, selenium, gallium and many others, most of which had few or no known uses in the recent past. Although the mining industry has been successful in developing ever larger mines and increasing the scale of production, the key issues underlying the future of the industry are declining ore grades, increased tailings and waste rock generation, the presence of toxic or other impurities, balancing the economics of primary and secondary products, stricter environmental conditions, more difficult exploration, increasing community expectations, as well as the processing of more complex or refractory ores, let alone the recent volatility in world commodity markets. Here, we synthesise our recent research on many of these various issues, focusing on the need to link all areas within the mining chain from mineral resources through mining to environmental performance in order to ensure we obtain the most out of our modern mining effort. The paper presents a unique and detailed assessment of the sustainability challenges and opportunities facing modern mining – and geometallurgical thinking is at the heart of this conundrum.CITATION:Mudd, G M, Jowitt, S M, 2016. From Mineral Resources to Sustainable Mining – the Key Trends to Unlock the Holy Grail?, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 37–54 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By C K. Boafo, J Visser

Obuasi Mine in Ghana, with more than 100 years of mining history, developed from a surface operation into a deep >2000 m underground gold mine. The challenge is to extract value from narrow veins left after extensive mining in the wider ore zones of the mine. Since the merger of AngloGold and Ashanti Goldfields in 2004 the mine strives to achieve optimum extraction through an integrated Mineral Resource management process from geological modelling, resource evaluation to mine design and scheduling. The shear hosted gold deposit displays complex secondary shears of variable thickness and continuity. There is an ongoing process of changes taking place in the way that geological modelling and resource estimation is done. Recent developments include the use of computerised systems that support the whole resource management chain from resource modelling to reserve optimisation. The change in thought and technology now allows for targeting narrow veins previously ignored in optimisation and mine design since moving into mechanised mining. The increased knowledge and confidence in the resource models now allows for flexibility in mine design, selection of mining method and scheduling and extraction of the reserves. The focus area for change is the way the orebody is evaluated and extraction designed. Since 2005 major changes were made to the process. This paper considers the historical approach of resource management. It looks at the individual process changes and qualifying the way ahead.

Jan 1, 2008

Barrick Gold Granny Smith Mine is currently undergoing conversion from an open cut operation to an underground mine at the Wallaby deposit. The underground project commenced in 2005 with the development of the reserves immediately below the pit and is now currently entering a production ramp-up phase for mining of these two initial surfaces below the pit. With increasing gold prices the owner has been forced to re-evaluate the underground project and has decided to investigate the potential of a deep level mine. This deep level underground mine presents a collection of challenges with the most notable being exploitation of a series of well separated near horizontal lodes ranging in thickness from less than 1 to 20 m. A variety of room and pillar mining methods are employed for extraction with careful consideration to resource recovery and pillar design for long-term stability. Compounding these deep level challenges is a need to accelerate mine level development to maintain the production profile of the mine. This paper describes the challenges, key learnings and outcomes of the studies undertaken to date associated with this project.

Jan 1, 2008

By M Stephens, T A. Sutra

Currently, there are several open pit mines with production rates of about 200 000 tpd of ore that are reaching the end of their economic lives. In most cases, the remaining orebody extends to depths greater than 300 m below the pit limit, leaving hundreds of millions of tons of reserves that can only be recovered by means of an underground mining method. One such method used for mass production is block caving. This paper presents a ventilation system for a four-zone block cave mine operation developed on a footprint 1000 m wide and 1200 m long. The system is designed for a mine with a nominal production rate of 120 000 tpd of ore using diesel powered units on the production and reduction levels. It discusses the air quantity requirements for the worst case scenario, which is anticipated to occur five years after the mine has reached its full production capacity. Finally, it summarises the results of computer modelling exercises that were carried out to determine an economic ventilation infrastructure that includes shafts, drifts, main fans, and ventilation control devices.

Jan 1, 2005

By M Habte

This paper presents a simplified method for the assessment of creep deformations in rock masses containing bands of low strength or soil strength rock. The main impetus for this work was the need to assess the impact of distinct bands of clay and/or low strength rock on the long term deformation behaviour of a rock pillar formed as part of a series of proposed tunnelling works. In particular, the authors were interested in being able to provide criterion which could be used by site personnel to assess the encountered rock conditions against design assumptions.Creep deformation versus time plots are presented for a range of material consistencies. These plots were produced using the hyperbolic creep equation proposed by Mesri et al (1981). This empirically based equation was chosen for its simplicity and practicality. Discussion is included regarding typical input parameter values and the sensitivity of the results to these values is explored. Finally, in the soil strength materials, the secondary consolidation equation is used to check the veracity of the results calculated using the hyperbolic creep equation.

Mar 8, 2011

By C Parihar, R Garg, A Bhandari, S Bhandari

Blasting can impact the efficiency of entire downstream mining operation. Individual technology solutions for blasting have been available in the industry for many years but all of them only cater for certain aspects of blasting. Many of them are based on individual research and/or experiences. Some of the available software solutions are not suitable to be used in the field as that they need advanced skills or tools. Also, most do not take technology advancements like mobility, advanced data analytics, web solutions and integration into consideration. Hence, no technology platform is currently present in the industry that addresses all potential needs a blaster may need in an integrated manner.This paper presents an integrated solution that takes care of all aspects of blasting – design blasts according to mine plan; collect data after drilling has been carried out (as there is often difference in designed and actual drilled hole locations in the field); predict blast results in terms of fragmentation, flyrock, ground and air vibrations, wave front reinforcement and flyrock distance; and after assessment, allows changes in charging, delay timing and sequence. The technology solution is a secure, cloud-hosted, web-based software-as-a-service solution that can be accessed from anywhere. Also it has a mobile app, which is available for both Android and iPhone/iPad. The mobile app is also integrated with the web-based solution using application programming interface calls to the central data repository.Case studies for two limestone mines are presented where this solution is being used in its initial format. This software platform enabled analysis of the outcome from a previous blast pattern and then subsequently allowed optimisation of blasting operations based on historical data. Uses of this platform have resulted in improved key performance indicators in these two limestone mines. The mobile app as part of this platform enables extensive field blast data capture and analysis and also various predictions before a blast. Data collected include blast parameters, individual hole charging, initiation pattern, videos, photographs and vibration records for analysis/reporting. The key features of the solution are a blast designer, a detailed blast data collection/analysis and a series of environmental predictors. These predictors give blast results in terms of fragmentation, flyrock, ground and air vibrations and wave front reinforcement and take remedial steps before blasting to optimise and control adverse environmental impact. Many features, such as fragmentation predictor and mobility solution, are completely unique features that are not available elsewhere in such a field personnel-friendly manner.CITATION:Bhandari, S, Parihar, C, Garg, R and Bhandari, A, 2015. An integrated technology solution for optimised and environmentally-controlled blasts, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 393–400 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By K Ehrig, V Liebezeit, Y Li, B Pewkliang, M Smith, E Macmillan

Pre-concentration of low grade ores via the rejection of low/no value materials based on fragment size is the subject of many published papers and studies over the past decade. However, the possibility of upgrading should not limited to low grade ores given the high cost of capital, energy, water, reagents, and ultimately tailings storage across the mining industry. Mining and processing facilities at Olympic Dam consist of an: 1) underground mine where ore is extracted via sublevel open stoping and 2) integrated processing plant located on the surface which produces Cu-cathode, Au-Ag bullion and uranium oxide concentrate. Blasted ore is trucked/trained to underground crushers which produce an ore feed with a product size P80 = -145 mm. Crushed ore is then hoisted to the surface and delivered to the ROM pads via an overland conveyor. The typical copper grade of mill feed is approximately 2 wt%. A rapid assessment of the potential to upgrade Olympic Dam mill feed prior to the ROM pads via rejection of low value materials based on fragment size was completed using existing data. Three separate datasets were utilised to assess the deportment of Cu, U, Au across size ranges of 200 mm down to sub-8 m. Cumulative grade vs cumulative mass distribution graphs for each element were produced. This data clearly demonstrates that Cu, U, Au grades remain constant down to ~212 m, which happens to be the liberation size of the sulfides. Hence, no potential to upgrade the ore stream via rejection of +200 mm - to ~212 m sized materials prior to milling. Mineralisation within the Olympic Dam Fe-oxide Cu-U-Au-Ag deposit (IOCG) occurs as disseminated sulfide grains within granite- to hematite-rich breccias. The typical sulfide grain size is sub-200 m that supports the outcomes of the grade deportment by fragment size study.

Nov 10, 2020

By U König, N Norberg

Traditionally, quality control of iron sinter has relied on time-consuming wet chemistry. However, the mineralogical composition that defines the physical properties, such as strength or reducibility, is not monitored.X-ray diffraction (XRD) analysis in combination with Rietveld quantification and statistical data evaluation using partial least squares regression (PLSR) has been successfully trialled to determine the mineralogical composition and process parameters such as the FeO (Fe2+) content and basicity of iron sinter within an analysis time of less than eight minutes per sample. The results were compared with wet chemistry data.PLSR does not require pure phases, crystal structures or complex modelling of peak shapes. The analysis is therefore easy to set up and ideal if only one property needs to be analysed. PLSR results show an accuracy for the FeO content of ±0.3 per cent for the samples analysed in this case study.Both the PLSR and Rietveld methods take the full XRD pattern into account and can be simultaneously applied on the same measurement. PLSR was found to be the more robust method if only FeO and basicity results are required. The Rietveld method helps to predict other parameters, such as the compression strength of the sinter, by monitoring all existing phases (eg larnite C2S or silico-ferrite of calcium and aluminium phases).CITATION:König, U and Norberg, N, 2015. Iron sinter process control using x-ray diffraction, in Proceedings Iron Ore 2015, pp 53–60 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By A Wanninayake, E Novello, I Gillani

A residue storage facility (RSF) was designed to cater for Davidson Creek Area and Robertson Range Area operations under the FerrAus Pilbara iron ore development project in the Pilbara Region, Western Australia. Annual ore production was about 15 million tonnes over a period of up to 15 years. The RSF was designed to handle a tailings production rate of 2.2 Mt/a over the project life with ability to be expanded at a later date. The composition of tailings was predominantly -45 ¦ material with some spiral reject material. The fraction of solids was expected to be between 40 per cent and 50 per cent solids by weight.The RSF was designed as an above ground storage facility, integrating with a mine waste dump planned close to the selected RSF site. This integration helped to increase the stability of the RSF embankment and to reduce the construction cost. The main source of construction material for the remaining part of the RSF embankment was selected to be mine waste. The RSF was designed to be constructed in stages by considering the availability of mine waste according to the mining schedule. The use of mine waste for construction of RSF embankments has several benefits over use of borrowed material. These include less construction costs and less disturbances to the environment, by minimising borrowed areas and waste dump footprints.CITATION:Wanninayake, A, Novello, E and Gillani, I, 2013. Effective use of mine waste in the design of a residue storage facility, Pilbara region, Western Australia, in Proceedings Iron Ore 2013 , pp 39-44 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By N Haque

Base metal ores contain low levels of toxic/hazardous elements such as arsenic, antimony, bismuth, cadmium, lead and mercury. Given the large tonnage of base metal ores mined and processed each year globally, the accumulated mass of minor elements introduced into the biosphere is large and could be expected to have a significant environmental impact. Life cycle analysis (LCA) is a methodology that has been developed to assess the environmental impacts of material supply chains over their entire life cycle. Assessing the toxicity impacts of metallic wastes and incorporating these impacts into LCA methodology is not a simple task given the complexity of the issue. However, research and methodology development is in progress internationally to address this. Despite limitations concerning the lack of a coherent framework for characterising the toxicity impacts of metals, including issues such as bioavailability, a study was carried out to give first estimates of the relative toxicity impacts of various waste streams from metal production processes. The wastes considered were: red mud; sulfide tailings (copper, nickel, lead/zinc); lead/zinc slags; synthetic rutile residue; iron oxide residue; and copper slags and anode slimes. These toxicity estimates can be considered the æworst caseÆ scenario for these wastes, where all the metals present are bioavailable. Combining estimates of the amounts of the various waste streams produced in Australia each year with the toxicity results showed that despite their relatively low human toxicity impact per unit mass compared to some other waste streams, red mud and the various sulphide tailings had the highest annual human toxicity load on the environment, along with copper smelting slag and dust. Data from the pH dependent leaching test reported in the literature were assumed to represent first approximations of metal bioavailability and used to compare the two approaches to estimating the toxicity impacts of red mud.

Jan 1, 2009

By E Deucker, A White

Gold Fields Australia (Gold Fields) has identified that improving productivity through more detailed shift planning and operational control of mining activities is a key driver to the success of their business. The Hamlet mine was chosen as a pilot site to trial a system that would allow production engineers and shift bosses to align the execution of short-term activities with the longer-term goals of the organisation.Gold Fields partnered with Deswik to introduce an on-site, collaborative, web-based system to allow mine planners to quickly build-up a detailed, activity-based, shift schedule for the coming week from the 13-week plan. Multiple stakeholders could then review and alter the plan, and then track and manage the execution of the activities.The system is designed to be integrated with production data capture systems to allow tracking of progress towards completion for each activity, as well as to plan and monitor the equipment operating in the mine. Integration of systems allowed engineers to use the large quantities of production data being captured to make informed decisions in the operations environment.The system replaced a complex set of spreadsheets that required expert users in Gold Fields to maintain. By capturing the data in a central database, the planning process is transparent and historic data from the execution of activities is available for analysis to improve productivity in the future.The system has ensured that the highest priority and critical path activities for the business are completed at the right time, improving the efficiency of operations.CITATION:Deucker, E and White, A, 2017. Productivity improvement through collaborative shift planning and tracking, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 225–234 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By N McKenzie, E Taylor, S V. L Barrett, H Lagger, A Purwodihardjo

This paper discusses the temporary support design methodology for the largest road caverns ever built in Australia—the Lutwyche Caverns—part of the Airport Link project in Brisbane, Australia. The Lutwyche Caverns with a maximum excavated span of 27 m form a key component of this major road project, allowing on and off ramps merging with the underground highway. In addition to the two large span caverns, a 15 m soft ground tunnel with 5 m cover above the caverns and two 24 m deep burial chambers for the 12.4 m tunnel boring machines (TBMs) had to be built in record time at Lutwyche.The temporary support design methodology involved the use of a range of analytical approaches, including empirical methods to provide a starting point for design development, key block models to determine the potential influence of discontinuities on excavation stability and 2/3D continuum and discontinuum models to determine the potential influence of adjacent excavations and the proposed construction staging on the design. In addition, probabilistic analysis of potential kinematic instability using a discrete fracture network (DFN) approach was also undertaken to establish the critical block loads for the temporary lining, while the continuum and discontinuum models were used to design the support for the 1.5 m diameter rock pillar at the north end of the northbound cavern.The numerical modelling was undertaken in close conjunction with the contractor to develop the optimal construction sequence, considering the available construction equipment on-site and the overall project program requirements. Part of the presentation will further show the applicability of the developed design during construction (deformations, monitoring field observations) and lessons learned for future cavern construction in Australia.CITATION:Lagger, H, Purwodihardjo, A, Barrett, S V L, McKenzie, N and Taylor, E, 2014. Temporary support design for the largest road caverns ever built in Australia – the Lutwyche Caverns, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 399–410 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By P Kirsch, P Jagals, D Viswanathan, J Shandro, R LaBouchardiere

The planning, design and operation of mines must include the development of positive environmental, community and land-use benefits if it is to achieve good corporate social responsibility and minimise detrimental impacts throughout the life of the mine. Life-of-mine (LOM) planning should, therefore, consider conducting mining activities in the best socially, environmentally and economically acceptable manner, from the commencement of exploration to post-closure of the mine. Current knowledge of LOM activities in relation to public health (life-of-community, or LOC) impacts neither fully captures the full suite of human health and well-being impacts, nor comprehensively informs society on these issues. This knowledge gap is becoming more apparent as public antipathy is increasing towards mining activities within Australia, Canada and globally. The purpose of this paper is to present preliminary and informative results of a literature review to gain insight into the extent of available public health and well-being knowledge associated with mining development. LOM development must also benefit the LOC, in that it must aim to minimise detrimental impacts, and maximise beneficial (including health) impacts on all associated communities. Health planning and programing for mitigation of potential adverse health impacts of mining should extend beyond the scope of work-related injury and illness (resulting from chronic exposure to harmful substances, infectious and lifestyle illnesses), to the health and well-being of workersÆ families and extended associated communities. By mapping the available but rather scarce literature on LOC areas to recognised LOM stages, this review found shortcomings and imbalances regarding research reporting on mining and its health-related impacts in the worker-to-community continuum.CITATION:Kirsch, P, Viswanathan, D, LaBouchardiere, R, Shandro, J and Jagals, P, 2012. Health impacts extend from the life of a mine to the life of a community - Knowledge gaps, in Proceedings Life-of-Mine 2012 , pp 161-168 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012