Search Documents

By G Noonan, S Thomas, M Limbert

Stuck drill rods (often referred to as bogged rods) in production ‘upholes’ are a common problem in the underground mining industry. Bogged and broken off drill rods have the potential to fall out of the hole without warning, posing a serious hazard to personnel and equipment below.Current industry practice to alleviate this hazard can be to either grout the hole in order to lock the drill rods in place, or to ‘plate over’ the hole with a rock bolt. Each of these operations seriously delays mine production as both require demobilisation of the production drill and mobilisation of alternative personnel and equipment to address the hazard. Both methods have been assessed for safety and efficiency and were found to be expensive, time consuming and in the case of plating over, ineffective.To address the safety and efficiency short-comings of the traditional practices, the long hole plug (LHP) has been developed to safely secure the lost rods in the hole. The LHP when struck by falling drill rods behaves similar to an expansion shell anchor transferring the axial forces from the falling drill rods horizontally into the rock mass. It is installed using standard production drills allowing work to safely continue with little interruption.Extensive testing has been carried out on the LHP in the laboratory and underground at the Rosebery mine on the west coast of Tasmania, Australia. Testing has included static pull testing, full scale drop testing and underground trials.The outcome of this work has proven the LHPs ability to add safety, volume and cost benefits to the Rosebery underground operation and it is currently in use at that site. It enables proven elimination of a common workplace hazard immediately, thus eliminating delay on the mine’s production cycle.CITATION:Thomas, S, Noonan, G and Limbert, M, 2017. Long hole plug – addressing the hazard of bogged rods in ‘upholes’, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 305–310 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By Vestre J, Kure K, Bergqvist I

Existing practical laboratory tests for comparative strength determination of commercial explosives consist of the lead block test, the ballistic mortar test, the bubble test etc. These tests are carried out in material with quite different properties compared to rock. The theoretical performance potentials of commercial explosives are traditionally described by weight-strength (WS). Some explosive producers use the Langefors formula for weight-strength calculation, where also the gas volume is considered. Neither the theoretical nor the practical methods for determination of explosive performance such as the above, give good enough prediction of fragmentation and heave in rock blasting. For these reasons a project was started for the purpose of finding a small scale test method which predicts how different explosive parameters affect fragmentation and heave. Small scale tests were carried out by using 50 cm cubical blocks, mainly of concrete, but a few also of rock. All blocks were blasted in a steel cylinder with a diameter of 1.2 meters. The velocity of detonation was monitored, and the velocity of fragments was derived from their time of arrival at the steel wall, which was registered by accelerometers. After blasting all fragments were screened. The charge diameter was 22 mm and the amount of explosive 78 grammes, resulting in a specific charge of 0.62 kg/m3. Explosive properties such as energy, gas, VOD and density were systematically changed.The results presented in this paper show how fragmentation and heave systematically change when the explosive properties like energy, gas, VOD and density are systematically changed. The results from the small scale tests are compared to full scale tests carried out in tunnel blasting, and during summer 1990 also in bench blasting.

Jan 1, 1990

By Q Zhuo, P C. Pistorius, M N. Al-Harbi

A likely increasingly important pathway for future low-carbon ironmaking and steelmaking is the combination of gas-based direct reduction with electric furnace steelmaking (DRI-EAF route), or with electric smelting (DRI-ESF route). In the DRI-EAF route, the gangue that is present in the iron ore is fluxed and removed as slag in the melting (steelmaking) step. This is in contrast with integrated steelmaking, in which the gangue is removed as part of blast furnace ironmaking. For DRI-EAF steelmaking, the amount and composition of slag depend on the iron ore composition, flux additions and iron yield. Slag volume and composition affect phosphorus removal, foaming behaviour and the process energy requirements. In this work, heat data from a year of DRI-EAF production was analysed to test whether the expected relationship between slag volume and electricity consumption for EAF steelmaking was observed. The data include slag analyses (one sample per shift), and heatlevel information on all inputs, final steel temperature and dissolved oxygen concentration, electricity consumption, tapped steel mass and tap-to-tap time. In analysing the data, the slag volume was estimated from the assayed slag CaO concentration and CaO inputs to the EAF. The expected effect of slag volume on steelmaking energy consumption was calculated with a mass and energy balance, considering the heat of mixing of the slag. The calculated energy requirement of slag formation is in line with previous estimates reported in the literature.

Aug 21, 2024

By M Svartsjaern, D Saiang and K Mäkitaavola

The Kiirunavaara mine is a large-scale (28 Mt/a) iron ore mine located in northern Sweden. The mine is owned and operated by Luossavaara-Kiirunavaara Aktiebolag (LKAB) using sublevel caving (SLC). The SLC area underlies an open pit decommissioned in the 1950s, the current main SLC haulage level is situated at an depth of 1100 m. The main orebody dips 60 degrees to the east with a distinct boundary defining the hanging wall to the east and footwall to the west. Since the 1980s damage has been observed both in the footwall rock mass as well as on the footwall crest of the open pit. Recent investigations indicate that the underground footwall damage is primarily controlled by large-scale slope failure mechanisms. Structurally controlled near-vertical planar shear failures in the upper footwall appear to be driven or facilitated by a step-path like curved shear failure situated in a zone starting ca 250 m, and intersecting the SLC about 100 m above the active mining level. To confirm this failure evolution a pilot underground measuring system has been designed and installed to monitor the expected rock mass displacements indicated by numerical models based on the above mechanisms. The systems consists of 50 m time domain reflectometry (TDR) coaxial cables installed in the footwall both across and away from an estimated damage extent boundary to monitor shear movements along natural joint surfaces. The TDR installation is combined with long extensometers to facilitate differentiation between diffuse shear and rock mass normal expansion. Additionally, a low-tech system of tape extensometer lines are installed in drifts and stopes running perpendicular to the ore strike to monitor horizontal displacements in the infrastructure as the footwall ‘slope’ loses confinement during mining advance when the mined out areas are replaced by caved rock from the hanging wall.CITATION:Svartsjaern, M, Saiang, D and Mäkitaavola, K, 2016. Underground footwall monitoring at the sublevel caving mine – Kiirunavaara, Sweden, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 773–780 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By S S. Kanchibotla, I Brunton

Most blast fragmentation models assume the rock mass properties, explosive properties and blast design variables to be constants and uniformly distributed within a blast. However, in reality all these input variables vary within a blast resulting in variation in the resulting fragmentation size distribution. A stochastic modelling approach is introduced in this paper to quantify this variation. This technique takes the input variables as statistical distributions rather than constants and through several thousand iterations, generates a statistical representation of the expected fragmentation resulting from a production blast. A case study of three production blasts from a large open pit mine are presented and the modelled fragmentation æenvelopeÆ shows good agreement with the fragmentation æenvelopeÆ estimated from Split image analysis. The various blast-related parameters influence different parts of the fragmentation distribution, eg rock strength and explosive velocity of detonation have most impact on the fines. The technique is used to identify the parameters that have the greatest influence on various size fractions. Such an analysis will be useful to direct resources to efficiently minimise the variation.

Jan 1, 2001

By R Kjar

Globally, it is anticipated that the mineral sands industry will enter a period of short supply. Demand for both titanium dioxide and zircon is forecast to continue increasing, with new projects needed to come on-stream to fill the supply gap. Victoria is well placed under this scenario as a source due to the high quality of its mineral assemblage, its excellent resource grade and the globally significant size of its mineral sands resources.Australia’s mineral sands rich Murray Basin remains under-developed, especially at its extensive Victorian margins. Development to date has not progressed adequately for the reasons of technology difficulty, history of competition with other jurisdictions and the absence of a platform that requires development as a consideration for security of tenure. Victoria’s mineral sands potential is not just about the Murray Basin, in addition, there have been discoveries in the Gippsland Basin and prospective sites in the Gippsland Basin remain under-explored. Key problems included the lack of available ground for potential developers and the intellectual property of solutions to technological problems associated with the fine grained mineral deposits belonging to a previous developer (with patents now expired).As such, the timing is right to re-visit the potential of the Murray Basin as a site for long-term development with high returns based on current and predicted prices.In order to understand why Victoria’s earth resources in general, and mineral sands in particular, remain under-explored and undeveloped, the Department of Primary Industries initiated an internal review of its role in encouraging and supporting investment in the earth resources sector.As a result, the Victorian Government has committed to taking action to encourage effective ground turnover and acknowledges that a new focus on engagement with industry is needed to bring new investment to the State. The revision of the Mineral Resources (Sustainable Development) Act 1990 provides an opportunity for the government to better align its legislative processes with industry project lifecycles and facilitate access to valuable resources that currently remain undeveloped.Victoria has a track record in assisting projects reach development stage. Iluka currently has two operations in the State in addition to its mineral separation plant that is capable of processing HMC from its South Australian operations. Iluka is expected to ramp up its Murray Basin Stage 2 operations with the WRP mine scheduled to come on line in early 2012. Meanwhile, Astron is actively seeking partners for its Donald Mineral Sands project. The project is becoming increasingly attractive given the recent price hike in zircon; Astron has access to an estimated five to 6 Mt of zircon in its Donald WIM 250 deposit.Given its substantial and valuable mineral sands endowments, the State of Victoria should sensibly be the centre of future investment in project development. However, as previously mentioned this is currently not the case. The Government is therefore committed to implementing new measures that protect security of tenure but ensure that genuine companies can access endowments where they have a clear intent to work those resources.

Oct 5, 2011

By G Cooper

The Société Nationale Industriel et Minière (SNIM) is expanding its ore and concentrate production capacity in Mauritania, West Africa. This government-controlled mining company has been in production since 1963 and currently exports some 12 Mt/a.SNIM is presently doubling its magnetite concentrate production at the Guelb el Rhein mine. An existing processing line will have a second parallel production line of 4 Mt/a added. The mine is located some 600 km inland from the Atlantic coast in the heart of the Sahara Desert.The metallurgy of the ore is reasonably straightforward. It is a magnetite banded iron formation that is amenable to magnetic separation. While the existing plant uses semi-autogenous grinding and dry magnetic separation, the new processing line will use HPGRs, dry magnetic separation, and a wet milling and magnetic separation circuit for treating middlings.The process choices refl ect the scarcity of water in the region, the high cost of locally generated power and the operating experience and preferences of SNIM. Dust control in the desert environment has been a particular challenge.The metallurgical design aspects as well as the infl uence of the environmental and commercial aspects of the project are presented.

Jul 11, 2011

By G McCullough, J Els, J Bassan

Integrated Remote Operations Centres (IROCs) have a crucial role in optimising a mine’s carbon emissions, especially as industry faces an imperative to achieve net-zero emissions on an accelerated timeline. To meet this time pressure, operations must adopt a comprehensive approach to energy-related carbon management and history has proven that modern technologies cannot be simply bolted into existing operations. An IROC is the most dependable solution to enable a swift transition from strategy to operational tactics that support carbon optimisation. Achieving net-zero emissions requires addressing significant energy management challenges such as fleet electrification, integration of renewable energy sources and large-scale energy storage. These challenges demand a profound change in planning, managing and executing work at large operations. The key to overcoming these challenges is an integrated approach incorporating collaborative decision-making across the value chain and more sophisticated planning approaches. Additionally, closer integration with downstream processing offers opportunities for carbon optimisation across the value chain. This includes the ability to supply tailored products that meet more varied feed-requirements of customers transitioning to less carbon-intensive processes and developing collaborative decision-making across the entire steelmaking value chain (by incorporating steelmakers, transport, coal/natural-gas/hydrogen supply, energy supply and iron-ore supply). However, this requires significant improvement in collaborative maturity and integrated decision-making capability. Finally, the imperative to reduce carbon emission demands the introduction of a range of new technologies into existing operations. The new technologies will increase the operational complexity of the mines and IROCs will need to evolve capabilities to manage the increase complexity and support the effective operationalisation and integration of these new mining technologies. This paper outlines the new capabilities required and the role of IROCs in effective integration across the demand value chain. The focus is on building on the mining industries’ existing IROC experience and augmenting with processes, technologies and lessons from other industries.

Sep 18, 2023

By P B. Swart, P D. Erskine

Despite an increasing focus by media, communities and activists driving an elevated regulatory focus in Australia and indeed some other mining jurisdictions, the mining industry globally has had limited successful mine lease relinquishments and transfers to support a next land use.Critique from anti-mining lobbyists frequently uses the large estimates from historically abandoned mine sites to influence risk-averse regulatory reforms to improve environmental performance. The mine rehabilitation regulatory processes in Australia, and specifically in the State of Queensland, are thus largely in place to prevent mining operators from abandoning their obligations.Regulatory responses to the lack of mine rehabilitation and closure performance in the last five to ten years have primarily focussed on compliance and enforcement of rehabilitation conditions in environmental approvals. Additionally, financial assurance measures have been tightened to protect against abandonment of rehabilitation obligations by the Industry, including the Chain of Responsibility legislation (Queensland Government, 2016b) in April 2016, to hold to account those who have benefitted from mining and processing/refining projects, and then avoid their environmental obligations.CITATION:Swart, P B and Erskine, P D, 2018. Are our closure planning and regulatory processes adequate to identify, quantify and appropriately transfer residual risks after successful mine rehabilitation?, in Proceedings Life-of-Mine 2018, pp 155–158 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By A R. Sale

This paper highlights two aspects of the mineral sands industry in Australia: the development of the industry from approximately 1870 through to 1980, and the author’s experience in the industry from 1966 to date.The first real heavy mineral (HM) mining in Australia started in 1870 with the mining of heavy mineral slicks on the beaches along the east coast of Australia. The real potential of Australian heavy minerals was however only realised in the 1920s with the first production of a heavy mineral concentrate that was shipped to Canada for processing. Post WW 11 and the Korean War, Australia was the largest producer of mineral sands products in the world as well as a significant developer of associated separation equipment and technology. The number of producing companies in the east coast peaked at 33 in 1957, was reduced to ten by 1965, and subsequently further reduced to five in 1980 as a result of potential mining areas being declared National Parks or Conservation Reserves. Today there is one company, Unimin Australia Pty Ltd (formally Consolidated Rutile Ltd) operating on the east coast. In contrast there were three companies on the west coast in 1965, four companies in 1980, and four companies today (albeit not the same companies).There have been considerable ups and downs for the industry in Australia, however world wide it was renowned in the past as being an industry that attracted numerous interesting and innovative characters that played a major role in developing it into the vibrant industry that it is today. This, given the current climate, is predicted to continue into the future.The author has been continuously involved in the industry for over 45 years from 1966, initially as an electrician at Consolidated Rutile Ltd culminating in the role of General Manager/President of Iluka Resources Limited USA, prior to his retirement in 2009. His exposure has been world wide and has covered all aspects of the industry but in the main focused on project development and operational areas. During this time there have been significant technological advances, yet to some extent the basic principles have not changed at all. Some of the most noteworthy advances include the development of the Wright Spiral in 1977, the development of the Reading High Intensity Wet Magnet (WHIMS), the rare earth magnets, the CRL floating thickener and the improvement of analytical techniques. From a safety, health and environmental perspective there has been significant advances that the industry has much to be proud of. These include wetland restoration both in Australia and in the US, the restoration of farmland in Virginia and Capel, and the re-establishment of native species, for example at Eneabba and Richards Bay to name but a few.

Oct 5, 2011

Efficient project planning during the detailed feasibility to final engineering stages of a project requires not only the accurate prediction of the grade, tonnes and recovery, but their degree of variability as well. An understanding of the major parameters involved in the grade and tonnage estimates is essential, and the communication to those receiving the results is most important. The personnel involved in the project require more than just a global reserves classification. Quality parameters other than grade should be evaluated as carefully as the estimate itself. This paper does not present any novel ideas to overcome or enhance any of this. Rather, it takes a step back and tries to look at the global picture of requirements for proper project planning.

Jan 1, 1987

This paper firstly reviews the requirements for container and hopper design for reliable discharge. Discussion is then directed to the evaluation of the consolidation stresses acting in both in both the cylinder and hopper sections during both initial and flow conditions. Here the vast difference, especially in vicinity of the bin outlet, between the initial or filling and flow conditions is highlighted. This vast difference has major design and operation implications. A further major implication is that all bulk solids must dilate to flow. The opportunity to simultaneously attain reliable discharge and partial moisture removal is also examined.The selection of design parameters to maximise the consolidation stresses in both the cylindrical and hopper sections is detailed. In regard to the latter, it is recommended fine coal bins be discharged using low friction lined transition hoppers with large outlet spans. Such outlets will discharge fine coal in a relatively compacted state. This compaction state should exhibit minimum water retention and short term moisture uptake.

Jan 1, 1998

By M Kent, D Elder, J Woodward, R Edwards, B Catto

At Tropicana gold mine (TGM), mine planning is completed from ‘one source of truth’ known as the Integrated Planning Model (IPM). The IPM is a block model which forms a core component of the TGM Mine Planning System – used for short, medium and long-term mine planning cycles, and for Mine to Mill reconciliation.The IPM was developed from a desire to consolidate long-term information contained in mineral resource and ore reserve models, with short-term information from the grade control processes, including grade control models and ore polygons.The IPM is informed initially by resource models, upon which the longer term budget and schedules are based. The IPM is routinely updated with grade control models and ore design information, providing increased confidence for short to medium term mine planning. In this format, the IPM also provides a framework for reconciliation of resource performance with grade control, mining actuals and mining schedules, and ultimately milling. As well as a means for analysing past performance through reconciliation, it has proven its worth as a predictor of variation and an input to successful schedule sequencing and change management. The IPM is a critical component of the TGM Mine Planning System, providing a centralised framework for short interval mill feed prediction through to life-of-mine (LOM) planning.Current development of the IPM is working towards incorporating Mine to Mill optimisation and real-time material tracking projects at TGM. If successful, the model will provide a truly powerful mine planning data source. Current development outlines a mechanism for tracking material from Mine to Mill, and for transferring mill performance data back to the IPM. Increasingly advanced material classification and mine planning, incorporating the multiple geometallurgical variables, will enable the mine to provide consistent mill feed products and result in a steady state and optimised mill.This paper outlines the vision, creation and benefits of the IPM at TGM. It also introduces the ongoing developments to ensure the IPM becomes only more relevant to successful and integrated mine planning as TGM matures from the new kid on the block to the old hand in the neighbourhood.CITATION:Catto, B, Elder, D, Edwards, R, Kent, M and Woodward, J, 2017. An integrated approach to mine planning – building the integrated planning model at Tropicana gold mine, in Proceedings Tenth International Mining Geology Conference 2017, pp 305–314 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By J Carrillo, A King

Gravity recoverable gold (GRG) is largely distinguished from other gold by its non-mineralised, metallic form, its high degree of liberation from the ore and its appreciable particle size. The gold mining industry has so widely accepted the use of batch centrifugal concentrators (BCC) and intensive cyanidation (IC) systems for the recovery of GRG that these may well be considered requirements of any plant processing ore containing appreciable GRG. The recovery of gold by gravity is quick, easy and cheap by comparison to alternatives. However, there are cases where attributes of the ore make recovery of gold by gravity and IC unusually challenging. This paper describes three examples where such challenges have been encountered and met, including those where the ore contains cyanide soluble base metals and where fine GRG is to be recovered from flotation concentrate.CITATION:King, A and Carrillo, J, 2018. Addressing challenging applications of intensive cyanidation in gravity gold recovery, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 283–290 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By A Mooney, J Marsden, H Grosser, G Dunstan

Carrapateena is a copper-gold deposit hosted in a brecciated granite complex, located 500km North of Adelaide, South Australia. The deposit is being mined using the Sub Level Caving (SLC) Mining method at a rate of 4.25 MTPA. The Carrapateena SLC construction was completed in Q4 2019, with ramp up to a mine production rate of 4.25 MTPA completed within 12 months; ~ 6 months earlier than originally planned (OZ Minerals, 2020b). Traditional SLC designs have had issues with safety interactions on production levels, namely at the perimeter drive, as well as presented challenges for the application of automation due to frequency of activity required to achieve ring turnover rates. Safety in design provides an opportunity to learn from experience at recent modern SLC operations and by considering hazards early in the design process minimise exposure and improve safety, productivity and automation of mining activity. This paper discusses the work carried out during the Carrapateena feasibility study and optimised during project execution; to update the SLC production level mine design, with a layout known as the Carrapateena Crows Foot Level Layout. This paper focuses on: • An introduction to the Carrapateena Operation and mine plan. • An overview and historical challenges of traditional level layout. • An introduction to the Carrapateena Crows Foot level layout, including production level design parameters as well as development metres and productivity comparisons. • Outlines the benefits of the Crows Foot design for safety in design of SLC operations. Provides a roadmap for improved production efficiency, level operational philosophy and the application of automation within the SLC.

Mar 15, 2021

By M A. Wells

A new approach to more reliably predict the Ni (and Fe, Mg) composition of Ni laterites was tested for RC samples from the (siliceous) oxide–style, Siberia North deposit, Kalgoorlie Nickel Project (KNP), in the north-eastern Yilgarn (WA) using partial least squares regression (PLSR) analysis of diffuse reflectance spectra over the 380 - 2500 nm wavelength range with a multi–element chemistry data set. PLSR cross-validation models were developed to predict FeO, MgO and Ni contents in composite samples with bulk composition limits of >0.08 wt per cent Ni and <6 wt per cent MgO. Calibration and validation models showed a strong, linear trend for predicting FeO and, to a lesser extent, Ni content, whereas PLSR models for predicting Mg content were less reliable. This reflected the prevailing mineralogy and associated element deportment within the oxide laterite profile. For example, Fe and Ni distribution is controlled by relatively few minerals, predominantly goethite and, to a lesser extent, the Fe3+-bearing smectite, nontronite. Magnesium is associated with a range of Mg-bearing minerals, some of which are compositionally complex (eg serpentine, talc, chlorite, smectite and carbonates). Magnesium chemistry alone does not reflect the varied mineralogy of samples with relatively high (5 - 6 wt per cent) MgO contents, which can be spectrally distinct. Hence, samples with similar Mg contents, though comprising Mg-bearing minerals with distinct reflectance spectra, were difficult to model (eg smectite versus Mg-carbonates). The findings of this study demonstrate that characterisation of Ni laterite composition may be achieved as part of routine logging of either drill chips or diamond drill core using PLSR analysis, but that a detailed understanding of the mineral-element association is essential for reliable predictive analysis. This has particular relevance to characterising the geometallurgy of Ni laterites, especially where deposits may be classed as the same type, but have distinct compositional and mineralogical differences.

Sep 5, 2011

During underground mining, rock mass changes can occur as a function of the mining sequence and excavation processes. Mining-induced rock mass damage can occur due to redistribution of static stresses and the application of dynamic stresses from blasting and seismic activity. These rock mass changes can result in a degradation of strength of the bulk rock mass and the remaining rock surrounding existing excavations. Rock mass damage near existing excavations which lead to excavation-scale instabilities such as rock fall, excavation closure, or visible rock mass fracturing can detrimentally affect the safety and profitability of mining operations.The focus of the current work was the prediction and assessment of damage to mine infrastructure occurring in relation to the blasting of a sublevel open stope. The study case involved a 60kt stope located in a highly-competent rock mass at a large Australian sublevel open stoping mine. The mine infrastructure of interest for investigation included local stope access development, critical access and haulage development crossing a regional-scale fault, an explosives storage magazine and a ventilation return air raise. The methods used to predict or assess the blast-induced damage to each infrastructure element in response to stope extraction were:- intact rock strength testing,- discontinuity mapping,- linear-elastic static stress modelling,- blast-damage mapping,- near-field blast vibration monitoring and analysis,- geophysical assessment using inferred stiffness and wave velocity methods, and- post-extraction void assessment.The results of the detailed blast damage prediction and assessment program at the mine site have been discussed by the primary author elsewhere (Fleetwood, 2010). The current work will address blast-induced damage to mine infrastructure as a result of extraneous blasting vibrations from stope production blasting. A method for predicting the amplification of excavation surface motions from reflecting body waves will be discussed as well as the results of damage mapping around the study stope. The results of the damage mapping program identified blast-induced damage that occurred to the surface of the explosives storage magazine and local stope access development. No damage was observed at the main fault crossing or return air raise where higher vibration amplitudes were measured or predicted.

Dec 6, 2010

By C Vejrazka1

The occurrence of airblasts is one of the principal mining hazards in caving operations between the time of cave establishment and breakthrough of the cave to surface. As such, it needs to be managed continuously and risk assessments need to be reviewed on a regular basis for applicability to changing conditions. The likelihood of an airblast occurring is based on a range of geotechnical factors over some of which engineers on-site only have limited control. However, the impact of an airblast to the underground mine, if it does occur, can be managed by following established safety guidelines for the production from the cave.This paper outlines how the Caving Airblast Simulation Tool in Ventsim was used to determine a risk management strategy for a sublevel and a block cave at a mining operation in Australia. The block cave has a footprint of 14 500 m2 with the extraction level located 1250 m below surface while the sublevel cave currently has a footprint of around 18 000 m2 operating between 660 m and 800 m below surface. Both caves are currently in their early operational periods. The risk analysis provided valuable information for the production planning of the caves including confirmation of extraction ratios for the block cave undercut, locations of airblast walls and maximum allowable air gaps for different muck pile heights to ensure safe operation is achieved.

Oct 12, 2022

By Lee H. G, Li H, Hayes P

Slag from the smelting of lead can contain up to 20 per cent zinc as an oxide. An understanding of the lead smelting process and of the subsequent fuming process for the recovery of zinc is enhanced by a knowledge of the activity coefficient behaviour of zinc oxide in smelting slags. The literature presents a wide range of contradictory values. This paper critically reviews the published data and outlines new measurements being made by the authors. A consistent set of zinc oxide activity coefficient data is presented for liquid slags within the ZnO-'FeO'-CaO-A1203-SiO2 system, through a combination of present and previous measurements.

Jan 1, 1993

By Esaki M, Nishimura K

This paper describes the results of the field application tests at Miike Colliery on the integrated automatization of the longwall mining system for medium thick coal seam. The purpose of the research is to develop an automatic longwall mining system which can be controlled accurately from outside of the face, and the ultimate goal is an eliminate of men from the face. Presently, the field test is being conducted in Yotsuyama mine following to a success in the performance test on surface. Remote Batch Control System for shield supports has been adapted to operate all supports from the control panel located at the entrance of the face. Remote monitoring and control system of the drum shearer has also been tested. The system makes it possible to operate the shearer either at the main gate or full automatic. Productivity and safety will be substantially improved as those systems enable to eliminate all workers from the face under the severe working conditions with high ground pressure and hot and humid atmosphere due to increasing mining depth. So far, we have been satisfied with the results of the field test and those system will be an effective countermeasure to operate the face with a high risk of rock-burst.

Jan 1, 1987