Search Documents

About 20 percent of world gold production has been contributed by gold deposits in Archaean greenstone belts, of which ca 2100 tonnes of gold has been produced from Archaean greenstone belts in Western Australia (Phillips, in press). These deposits are, therefore, important exploration targets and an under-standing of their nature and genesis can help to formulate exploration strategies and delineate potential targets.A literature survey of Archaean granitoid-greenstone terrains indicates that a wide variety of lithologies host gold deposits. The major part of production from the Yilgarn Block, Western Australia, has come from mafic volcanics andintrusives (70% of production),with significant contributions from BIF-hosted ores (15%) and low production from sediments, felsic volcanics, porphyry intrusives and granitoids (Groves et al., in press). Similarly, most

Jan 1, 1984

By R Jones

OneSteel Whyalla’s grate-kiln-cooler pelletising plant was commissioned in 1968 processing haematite feed from the local South Middleback Ranges mining area. The existence of a magnetite resource beneath the haematite ore at Iron Duke had been known for some time. In 2004, a decision was made to covert the primary iron source for the Whyalla steelworks from haematite to magnetite – known as project magnet. The intent of the project was to convert the feed to the steelworks from haematite to magnetite and to free up the remaining haematite resource for export. The pelletising plant was cut over to a magnetite feed in 2007.The thermochemical differences of magnetite compared to haematite are threefold:1. the introduction of an exothermic reaction during conversion of magnetite to haematite,2. the absence of bound water which existed within the haematite, and3. lower gangue content requiring lower fluxing levels and therefore lower calcination energy demand.The combination of these differences results in a significantly different induration requirement for magnetite as compared to haematite. The change therefore required extensive research and test work to design modifications to the furnace and to ensure appropriate risk mitigation for the Whyalla steelworks.Preliminary pot-grate test work was performed to define the pellet chemistry and confirm the suitability of the magnetite to produce pellets suitable for the OneSteel blast furnace. A heating curve was developed by use of computer-based heat and mass balance modelling. Extensive pilot scale grate-kiln-cooler test work was then performed to confirm the heating curve and to verify and fine-tune the pellet properties. Computation fluid dynamics was used to design the physical changes to the furnace required to achieve the proposed heating curve.Following installation of an additional preheat zone, including a wall and dilution air fans, into the preheating furnace, and installation of an additional wall into the cooler, the modified furnace was commissioning in December 2007. The plant performed as expected during commissioning with the actual heating curve matching the proposed curve and the produced pellets within blast furnace specifications.

Jul 11, 2011

By B Abbasi

It is well known that most roof falls in coal mines typically occur at and around intersections. Room-and-pillar and longwall coal mining systems typically develop 3-way and 4-way intersections. This research develops an improved scientific understanding of stress distribution and associated instability behaviour around 3-way and 4-way coal mine intersections through 3-D numerical modelling and limited field observations. Numerical analyses were performed for an Illinois longwall coal mine to identify factors that influence intersection stability. The stability of immediate roof, floor strata, and coal ribs at and around intersections are considered with pre-mining regional horizontal stress. Non-linear failure analyses used the Hoek-Brown failure criterion for rock mass. Progressive failure zones in and around intersections were developed. For a typical 4-way intersection, pillar corners across the intersection fail first and lead to progressive failure of the immediate roof and floor layers. The mechanism of failure is similar for a 3-way intersection but the shape and extension of failed zones differ. For the 3-way intersection, the effect of off-set distance was analysed. It was found that minimum off-set distance of about 10 m (centre to centre distance between two 3-way intersections) was required to minimize interaction between two intersections. A simple instrumentation program monitor ground movements around intersections. These data were used to design the intersection geometry that is now being practiced by the mine. CITATION:Abbasi, B and Chugh, Y P, 2018. Instability analysis in three-way and four-way coal mine intersections, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 345–359 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By S K. Michelic, M Schickbichler, A Kharicha, E Karimi-Sibaki

The requirements for the controllability of metallurgical processes are increasingly becoming the focus of both industry and research. Advances in this field of research not only impact the stability of processes but often also influence the quality of the final product. One important way to examine processes in-depth, and thus show potential for improvement, is to describe them using physicsdriven models. In metallurgy, thermodynamic and kinetic descriptions of interactions between individual components of a system are often used to describe and analyse important metallurgical phenomena across the entire process. However, for the creation of physics-based models, boundary conditions and process variables must be implemented to enable a description that is as realistic as possible. The collection and generalisation of boundary conditions and process variables is, therefore, an important step towards functional models. The focus of this study is the determination of mass transfer coefficients between all components in a steel/slag/refractory system. For this purpose, experimental and theoretical methods are applied. Laboratory scale experiments are carried out in an induction furnace, and the mass transfer coefficients of the defined steel/slag/refractory system are calculated from changes in the chemical composition of the various components. Additionally, a calculation of the mass transfer coefficients based on dimensionless quantities is carried out. By comparing the values of the mass transfer coefficients determined theoretically and those determined experimentally in the trials, the suitability of the calculation is examined. The collection of mass transfer coefficients provides essential findings for future kinetic descriptions of inclusion modification based on the effective equilibrium reaction zone (EERZ) approach.

Aug 21, 2024

By L McCallum, G Dale, B Silverwood, T Roscoe, A Costin

The introduction of Progressive Closure and Rehabilitation Plans (PCRPs) in Queensland from 2019 places greater importance on planning and implementation of mine rehabilitation activities. The progress and outcomes of progressive rehabilitation activities is monitored and reported upon to demonstrate success in achieving progress towards the approved post-mining landform, and to inform corrective action where required. The requirements of PCRPs place additional emphasis on mine sites to quantify the risks of successfully achieving planned outcomes. This is particularly challenging given mined-land rehabilitation is a complex process involving decisions on multiple inter-acting management interventions, climatic conditions and spatially variable site characteristics.

Aug 2, 2023

By Nava-Vasquez E, Torres-Torres J, Mendez-Nonell J

The ZA-27 zinc base alloy was poured into cylindrical moulds and solidified under different conditions ie normal freezing and unidirectional freezing. In addition a cylindrical ingot with rheocast material was obtained by stopping the stirring action and, at a specific solid fraction, gravity casting it into a graphite mould. It was observed that the material obtained under normal freezing conditions is likely to present both segregation and inverted pipe. In contrast, the unidirectional solidified and the rheocast cylinders showed the absence of inverted pipe. The segregation pattern was quite irregular in the rheocast ingot while such segregation was more uniform in the unidirectional solidified cylinder. By virtue of these observations, the inverted pipe formation may be ascribed to the interdendritic flow, while the irregular segregation pattern in the rheocast ingot may be attributed to an irregular distribution of the liquid and solid fraction along such a cylinder.

Jan 1, 1993

By D J. Gray

The 4 km long Huguenot Toll Tunnel in the Western Cape region of South Africa celebrated its tenth anniversary on 18 March 1998. At present a single (South) bore with bi-directional traffic flow is operational. The North bore was originally excavated but not lined and equipped.The tunnel is fitted with a semi-transverse ventilation system comprising 45/350 kW two speed fresh-air and 1 MW exhaust air fans at each of the portals. These provide ventilation through fresh and exhaust air ducts above the ceiling separated by movable partition doors. Secondary air ducts deliver air at low level. The fan control depends on the levels of CO pollution or visibility measured at six positions along the tunnel.The system performed well during initial tests and under conditions of low traffic volumes. As traffic volumes increased, and user complaints of bad air in the tunnel were received on several occasions, we realised that we had a problem. Tests confirmed that natural airflow within the tunnel induced by prevailing meteorological conditions outside the portals affected the performance of the ventilation system causing a plug of bad air to be trapped at varying positions along the operating tunnel.The control systems in the tunnel are presently being upgraded as described by Gray, Rieckert and Bullock (1998). As part of the retrofit we are implementing a new control strategy for the ventilation system which takes into account the external weather conditions. This paper discusses the 24 month long meteorological data gathering exercise, which is on-going, and explores the philosophies planned for controlling the ventilation system. The correlation between winds external to the tunnel and induced airflow inside the tunnel are examined. The effects of the weather induced airflow on the existing ventilation system are considered and proposals given for taking these effects into account in the new control strategy. These include the implementation of an expert system to predict ambient airflow from prevailing weather conditions, and the use of airflow measurements taken in the uncompleted North bore as a cross-check.The paper highlights the need to take cognisance of external weather conditions when designing tunnel ventilation systems.

Jan 1, 1999

By P Woodward, T Ly, N Muhamad

OZ Minerals' Prominent Hill copper-gold concentrator is located 650 km north-west of Adelaide in the Gawler Craton of South Australia. The concentrator was built in 2008 and commenced commercial production in early 2009. The Prominent Hill concentrator is comprised of a conventional grinding and flotation processing plant with a design capacity of 8 Mtpa. The flotation circuit includes six rougher cells, an IsaMill for regrinding the rougher concentrate and a Jameson cell preceding the three stage conventional cell cleaner circuit.Since its commissioning, the Prominent Hill flotation circuit has been the focus of a series of projects aimed at continual performance improvement. This has been achieved by a systematic approach of project identification, evaluation and implementation which has led to a progressive improvement in flotation performance. Innovations that have been successfully implemented include aspects of cell design and operation, and reagent suite optimisation.Improvements to the mechanical cells initially focused on the installation of a modified rotor-stator design in the rougher circuit, as recommended by Outotec. Isolated cells were fitted with this technology and proven to provide a benefit for copper recovery before the design was trialled in subsequent cells along the bank. Based on this success, further modifications were made to other aspects of the rougher and cleaner cells.Laboratory trials conducted at Prominent Hill involve a screening process identifying potential reagents from a list of products, which are then rigorously tested in the laboratory before one is selected for trial in the concentrator. Where these reagents have demonstrated a statistical improvement in performance they have typically been incorporated permanently into the flotation circuit. This paper discusses the process of continual improvement at the Prominent Hill flotation circuit and the optimisation achieved by the implementation of key initiatives.CITATION:Woodward, P, Muhamad, N and Ly, T, 2013. Optimisation of the Prominent Hill flotation circuit, in Proceedings MetPlant 2013 , pp 431-444 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By J Pearce, B Miles, V de San Miguel

Incorporating industry best practice waste rock management methods can be a relatively straight forward task when preparing management documentation, such as an acid and metalliferous drainage management plan (AMDMP). However, a key difficulty is the incorporation of industry best practice methods that are practical and non-compromising on their purpose from a scientific standpoint. The second key difficulty is the implementation of these practical methods as various operational groups/departments are typically relied upon to execute and take ownership of different tasks or procedures.One approach to overcoming these difficulties is to develop an AMD Operations Manual (AMDOM) that:•Incorporates, where practicable and without compromising scientific merit, existing processes that those groups/departments ultimately responsible for the execution of the management action are familiar with; and•Provides standalone, simplistic, and easy to follow procedures for site personnel. The purpose of the standalone operations manual is to ensure site personnel who are responsible for undertaking specific procedures, have clear, step-by-step instructions for an individual procedure, without requiring interpretation and understanding of the more comprehensive AMDMP.In adopting a best practice approach to waste rock management for their iron ore mine in Western Australia’s Pilbara region, Roy Hill developed an AMD Management System that is comprised of both an AMDMP and an AMDOM that are connected through adaptive management processes. The Roy Hill iron ore mine, which has a mine life of 18 years, will require the management of more than three billion tonnes of waste rock.CITATION:de San Miguel, V, Miles, B and Pearce, J, 2018. Practical waste rock management at the Roy Hill iron ore mine, Western Australia, in Proceedings Life-of-Mine 2018, pp 80–82 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By T Walsh, S R. Mudnuru

The development of lithium-ion batteries, coupled with the global trend towards electrification of transportation, has led to a dramatic increase in the demand for lithium. The production of lithium from hard rock ores is increasing, and flotation has proved to be an effective means for the beneficiation of many pegmatitic lithium ores. Clariant Mining Solutions has developed a range of novel collectors for the flotation of spodumene and other lithium ores, and this paper presents examples of some of the most recent developments. Fatty acids are the typical collectors for lithium flotation, however the grade and recovery achieved with these collectors is often below the desired level. There are also some significant drawbacks associated with the use of fatty acid collectors, such as the formation of calcium soaps which give rise to filtration problems and the need for acid washing. Several FLOTINOR products have been developed as alternatives to fatty acids. These products offer equivalent or better metallurgical performance at significantly lower dosages than fatty acids. This offers benefits to the flotation circuit as well as potentially reducing the issues associated with downstream processing of the concentrate.

Aug 24, 2022

By Grieveson P, Terry B. S

Carbothermic reduction of sulphide minerals for achieving a selective separation of metallic species from complex minerals has been discussed by considering the prevailing oxygen potential during the course of reaction. Construction of univariant plots for the reduction of sulphides with carbon monoxide gas or carbon and in the presence of either lime or anhydrous calcium sulphate is the key feature of this work. The theoretical calculations for univariants in the Cu-Fe-S-O system indicated a preferential separation of metallic copper and iron by imposing a chemical potential. This is evident from a logarithmic plot of sulphur dioxide partial pressure against reciprocal temperature. The results are compared with empirical data for the reduction equilibrium. The reduction behaviour of the constituent sulphides are also discussed together with the experimental results and theoretically predicted phase stability diagrams.

Jan 1, 1992

By R R. Lovel, G J. Sparrow

Currently there are large reserves of good quality iron ore near to existing infrastructure that are not being developed because the phosphorous levels are above acceptable market specifications. Since the high phosphorous content is considered to be mainly associated with the goethite fractions of the ore, attempts were made to leach the phosphorous from the ore after a heat treatment to dehydroxylate the goethite. Heating the ore and leaching with 40 g/L NaOH lowered the phosphorous levels from 0.145 wt per cent P to 0.075 wt per cent P or lower, but a heating temperature over 800¦C was required to achieve this reduction in phosphorous levels. However, when sodium hydroxide was added to the iron ore before the heat treatment, similar phosphorous removal was achieved with a heating temperature of 300 - 350¦C. It was considered that dehydroxylation of the goethite in the presence of the hydroxide makes the phosphorous available for removal with a water leach. As well, 50 per cent of the silica and 60 per cent of the alumina in the ore were also removed in the leach, but some sodium remained in the leach product. Further work is required to remove the residual sodium to produce a marketable product.

Jan 1, 2009

By J B. Holman, P A. Weber, P Lindsay

Underground and opencast coal mining has occurred since 1896 on the Stockton Plateau, West Coast, New Zealand. Acid Rock Drainage (ARD) from historic and current mine workings has had an adverse environmental impact on the surrounding aquatic environment. The two main catchments affected by ARD from historic and current mine workings are the Mangatini and St Patrick Stream catchments. Solid Energy New Zealand Ltd (SENZ) is using active (e.g. alkali dosing) and passive (e.g. engineered cover) technologies to mitigate the adverse environmental effects associated with ARD contaminated waterways. This paper discusses the passive technologies. Principal strategies include the capping of high capacity potentially acid-forming volumes of overburden. The mudstones were found to generally have the highest sulphur levels compared to other overburden lithologies. Areas with high mudstone volumes are prioritised to be encapsulated and 390 Ha is planned to be capped in the Mangatini catchment in the near future.   Monitoring beneath granite, cement kiln dust and coal combustion product covers show oxygen can be reduced to less than 10% of atmospheric levels. Laboratory column leach tests that were subjected to oxygen flux rates of 10 % showed reducing oxygen ingress into acid-forming material can result in significant acid load reductions.   The oxygen content below the cement kiln dust cover was generally lower than 5% and water quality measured in lysimeters beneath this cover improved after 50 weeks of emplacement. Column leach tests containing saturated samples were undertaken to determine the most appropriate water medium in preventing pyrite oxidation. The sample saturated with ARD (pH ~ 3) had a negligible acid production rate and leached very minor Al concentrations although Al is soluble at low pH. This indicated saturating waste rock dumps with ARD can be an effective method in mitigating ARD formation.

Jan 1, 2007

By D Monaghan

Pumping water for dewatering and water supply is a major component of electricity consumption at mining operations and hence is a significant contributor of greenhouse gas emissions. Pump systems at a typical mine site can be broadly split between above ground centrifugal pumps (generally used for water transfer) and submersible borehole pumps (generally for dewatering and/or water supply). In contrast to above ground pumps, submersible borehole pumps can be subjected to varying duty points (total pumping head and flow requirements) as a result of changing bore water levels and yields, particularly in mine dewatering bores. Typically, much higher pumping rates are required at the commencement of dewatering to remove groundwater storage and to intercept sufficient groundwater throughflow to achieve target drawdowns. Once target drawdown levels are reached it often only requires much lower pumping rates to maintain target drawdowns. Pumps sized to remove the large initial volumes of stored groundwater often end up too large for the lower flow rate required for æmaintenance pumpingÆ. This often results in pumps operating inefficiently, a problem which can be made worse when pumps are throttled to reduce the pump output to better match the reduced bore yield. Current standard operating practice places little emphasis on the electricity consumed by pumps, with the focus often being on minimising capital expenditure (æIf it ainÆt broke donÆt fix itÆ). Submersible pumps can have extended service lives of ten to 20+ years. However as the capital cost of a pump typically represents only five per cent of the life cycle cost, the vast majority of the life cycle cost is energy usage.Through the implementation of a regular review of the operation of borehole pumps, significant reductions in electricity use and associated greenhouse gas emissions can be achieved without impacting the dewatering schedule. In most cases, the capital cost of replacing pumps is more than offset by savings in operating costs. These potential savings become even more significant when considering proposed future carbon tax levees.This paper presents examples of the opportunities for significant reductions in energy, greenhouse gas emissions and overall costs that can be achieved for a range of dewatering scenarios.

Jan 1, 2009

By L D. Munro, S A. Jackson

This paper provides a logical approach to developing a TSF design concept through: • Identifying key properties of tailings and containment structures; • Reviewing underlying principles for effective operation; • Showing how these apply to select an appropriate TMS; and • Demonstrating how to align the TMS to site-specific constraints and TSF design. This approach follows a path of rigorous data analysis independent of discharge parameters (whether low-density slurry, paste or cake disposal) to select the most cost-effective and sustainable approach for any given material or site.

Jul 1, 2021

By M Zhu, G Tranell, N Simkhada, K Jakovljevic, M Wallin

Silicon is a vital element in many products today, such as electronic components, solar devices, high-quality alloys, and many others. The growing global demand highlights the need for the development of sustainable production methods to meet this demand as an alternative to the current carbothermic reduction, submerged arc furnace (SAF) based process. An alternative to this is the aluminothermic reduction of quartz in a CaO-SiO2 slag, which not only reduces direct carbon dioxide emissions but also promotes the utilisation of secondary raw materials such as quartz fines, aluminium dross and scrap as well as secondary alumina (SA) from dross recycling. In the current study, the effects of SA and CaF2 additions to slag on the resulting metal composition and metal yield were explored. Results were compared with thermodynamic simulations using FactSage™ 8.1. Experimental results show that, in agreement with thermodynamic simulations, the silicon content of the alloy is increased, while the Ca is decreased for starting slags where CaO-SiO2 is partly replaced by CaF2. Similarly, the addition of SA to the initial slag results in an alloy with a higher silicon content.

Jun 19, 2024

By H Masoumi, I Canbulat, Y Zhao, J Oh, H Lin

Borehole breakout is a drilling induced phenomenon caused by overstress of rock around the borehole. Its depth usually aligns with the minimum horizontal principal stress direction. For this reason, it has been used to determine stress orientations and a series of researchers also argued its dimensions can be indicative of stress magnitudes. If the stress dependencies of breakout geometries are well understood, it is possible to estimate stress magnitudes based on these data. This paper investigates the influences of critical parameters on breakout dimensions, including absolute stress magnitudes, stress ratios and borehole diameter. Several experiments have been conducted on cubic (120 x 120 x 120 mm3) sandstone samples with pre-drilled holes (22 mm and 30 mm) under true tri-axial loading conditions using UNSW self-designed equipment. Experimental results confirm the increasing maximum horizontal principal stress magnitudes result in larger angular span and longer breakout depth at constant minimum horizontal and vertical principal stresses. There is also a considerable discrepancy observed between experimental results and the analytical model. Findings of this study imply a potential on the estimation of stress magnitudes using borehole breakout. CITATION:Lin, H, Oh, J, Canbulat, I, Masoumi, H and Zhao, Y, 2018. Experimental investigation on borehole beakout and its implication on stress magnitudes, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 266–273 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By C G. Sweeney

The underground mining industry is seeing unprecedented shortages in skilled labour. Migration to Australia being at an all-time low is a leading concern, with pandemic-induced border closures and lockdowns only exacerbating the skills shortage, not causing it. The skills shortage is forecast to peak in 2023 and remain high beyond 2025. With this skills shortage in mind, mining companies throughout Australia are trying to deal with stricter protocols around Health and Safety (H&S) legislation, as well as more stringent controls on quality assurance, particularly as underground mines are reaching greater depths and extending into ‘unchartered territory’. The cumulation of this is proving to be a major hurdle in ‘effective’ operational geotechnical management. The drive for automation in mining is bringing another level of complexity. However, ‘once automation is up and running, it presents the opportunity to access talent pools that may not normally be available. There is also a change in skillset that will be required to drive automation. ‘The top two emerging roles that will be critical for the future of the mining industry are artificial intelligence and machine learning (AI/ML) specialists, and process-automation specialists’ (Writer, 2021). If anything positive has come from the pandemic, it has shown that remote working can be effective and that the drive for automation and critical evaluation of skills required on-site should be given greater priority. UQ acknowledges that the industry is changing, and that digital technology is required to be offered in mining related disciplines. Industry and academia need to do more to promote geotechnical engineering in mining and balance the curriculum to suit the future of mining and make it more enticing. The average cost of a geotechnical failure is about $5 million in coalmines and can be into the hundreds of millions of dollars if production is affected (Cartledge Mining and Geotechnics, 2020). The cost of a good geotechnical design far outweighs the potential losses if a failure were to occur. This alludes to the growing importance of experienced geotechnical consultancies playing a pivotal role in managing mine site geotechnical hazards, while the industry is developing the next generation of geotechnical engineers.

Nov 29, 2022

Many young mining engineers do not consider consulting as a possible job, believing that many years of working on-site is required to achieve practical experience, develop expertise and acquire industry contacts. However, mining consultancies employ engineers with varying levels of experience, including part-time university students, graduates and engineers who are relatively new to the industry. This paper outlines the role of a young engineer in a large mining consultancy and the benefits to both the consultancy and the client of having a mix of consultants with a diverse range of experience. From the authorÆs perspective, the work experience, lifestyle and rewards of mine consulting are compared to site based work, including a discussion on whether consulting is able to offer the professional development that a young engineer needs.

Jan 1, 2009

By J Player, G Sweby, S Webber, E Jones

Seismic systems are a tool for the monitoring and forecasting the rock mass response to excavation. Common issues encountered at mine site audits and reviews are: how to design an effective seismic system, implementation of the design, interpretation of seismic source results and understanding the reliability of the seismic source. These issues are often a function of several items including: • Experience of site personnel in undertaking seismic system design. • Personnel not envisioning multiple phases of system expansion to understand system robustness issues. • System design/expansion occurring in response to damaging seismic activity rather than planned expansion of a system • The mine access development is often localised in comparison to the total orebody being mined hence, planning sensors in longholes in advance of development rather than in short holes close to development will improve the three-dimensional aspect of the network. • Limited site processing of the seismic event data, hence engineers do not see the uncertainty associated with event location, size, source and system layout. Mine site users require a framework to appreciate the challenges and limitations in locating large events. For example, event locations are given as precise measurements (to the nearest centimetre) whereas the volume of deformation resulting in the event often has dimensions of tens of metres or more (as defined by the source radius). A stronger awareness of the uncertainty of rock mass yield within large seismic sources will assist site users in the interpretation of rock mass damage. The encountered design and implementation errors are reviewed and discussed with a practical set of rules presented to provide a robust seismic system that provides consistent results and increases the user’s understanding of uncertainty in source location and size. The authors’ experience across multiple mine sites, seismic systems and damaging seismic events over a 30 year period has been summarised into practical rules for site personnel of all experience levels.

Nov 29, 2022