Search Documents

By Carter NB

A statistically-designed experimental program has been used to study compositional and processing variables which influence the development of strength and reducibility of iron ore pellets. The effects of chemical composition and processing variables were investigated by indurating laboratory-made green pellets, of known composition, under approximately isothermal conditions in a pot- grate simulator. Some findings from a six- variable study are summarized in the form of contour diagrams and emphasize the importance of interactions between the variables. Production of strong, highly reducible pellets is possible over a considerable range of combinations of temperature and firing time. Abrasion index (AI) and cold compression strength (CCS) improve as both these variables increase, but reducibility (R) declines, so a compromise is required. When the lime level is too low to form enough slag for bonding, the AI and CCS may be inadequate. Larger additions of lime tend to improve AI and CCS, with only slight effects on R. Finer grinding of the balling feed (i.e. higher Blaine index) tends to improve Al and CCS without

Jan 1, 1980

By Fukuda M, Kurita K

A mathematical model for estimating the liquid level in the hearth is presented. The analytical result was checked on a cold two-dimensional model and an additional boundary condition for the fundamental equation resulted. The applicability of the resultant equation was investigated on a cold model and a regression equation obtained for the average liquid level for Kashima No. 1 BF. Comparison of calculated and observed results were in fairly good agreement. It is concluded that the liquid level in the commercial furnace can be calculated from the measured values of pressure in the bosh and operating conditions.

Jan 1, 1975

By Abbott T. M

Alcoa of Australia operates three Alumina refineries in the South West of Western Australia at Kwinana adjacent to the South suburbs of Perth and at Pinjarra and Wagerup in rural settings 100 and 150 kilometres south of Perth respectively (see Figure 1). Alcoa's total alumina production is currently around five million tonnes per annum and this will increase to 5.5 million tonnes by early 1990. Further expansion of production is likely if current world aluminium demand trends continue. Alcoa's refineries utilise bauxite mined in the nearby Darling Range which is low grade by world standards having around 32 % by weight extractable alumina (by comparison Weipa bauxite yields around 55% alumina). This means that for every tonne of alumina produced two tonnes of solid wastes remain and therefore while we in Western Australia can boast of hosting the largest alumina industry in the world with around 18% of total world production we suffer from having the lion's share or 40% of the world's bauxite residues to dispose of. In its Western Australian setting the management of these residues in a manner which is acceptable to the community creates many challenges. These are primarily due to the mass and volume of waste produced, its chemical and physical characteristics and the environmental features of the local area including close proximity of neighbours, competing land uses and the presence of natural resources such as surface water and groundwater. In addition the trend towards more stringent statutory environmental controls and greater political and community awareness of environmental issues means that we must be able to demonstrate improvements that will reduce the considerable adverse impacts of past practices. Of course we must also try to keep the overall cost of residue disposal as low as possible to maintain our competitiveness with refineries which may have much smaller volumes of waste to dispose of and less environmental constraints.

Jan 1, 1989

By Nidagal V

This paper discusses the dewatering strategy adopted and the considerations and procedures required to incorporate a dewaterinq scheme into the Mt Whaleback mining operation. It concludes that in pit pre-dewaterinq has successfully allowed mining to progress below the standing water level with the minimum of disruption or radical change to the mining method. It is recognised however, that dewatering is not a static activity and there is a requirement for ongoing investigations and development. Pre-dewatering commenced in October, 1984. Purpose designed pumping trailers have been employed to minimise the loss of pump availability resulting from the frequent. need to remove and reinstall pumps when close vicinity blasts occur. To July, 1986, some 0.5 Mm' of groundwater had been pumped from the unconfined orebody aquifer. Mining has progressed to some 20 m below the standing water level without. any undue water associated problems. Ultimately, it is ,cheduled to extend some 300 in below the original water level in the West Pit. With the development of an increasing area of the mine below the standing water level, the influence of seasonal high intensity rainfall events, which had previously caused little concern, now need to be addressed. Pumping equipment has been designed to evacuate storm water at a rate consistent with mine production Considerations.

Jan 1, 1986

By D J. Hill

"Mining companies routinely invest in improvements to their processing operations, but often these enhancements do not work to full effect.Improvements can be ineffectual because underlying process problems are not identified or prioritised for correction or repair.This is frequently because ‘black box’ solutions deployed to implement process control improvements typically rely on instrumentation to provide data for algorithms to work effectively, and these solutions are often ineffective or disabled at mineral processing sites.There are three key reasons they can fail to deliver: vital instrumentation is not calibrated or functioning as required basic process control and loop tuning was not implemented correctly or is in need of tuning there is an inability to support the ‘black box’ solutions on-site.Many of these problems can be overcome by implementing operational analytics that identify where problems are occurring and prioritise where improvements need to be made.Incorporating operational analytics into process improvement is not a new methodology. It is more a back-to-basics approach to make more efficient use of capital and systems already deployed.Data collection systems, such as the OSIsoft PI System, provide real-time and historical process information for process control experts to analyse and identify areas for improvement. However, most systems are not used effectively. With some simple enabling, data collection systems can provide evidence for prioritising investments in improvements and determining an investment’s effectiveness.MIPAC advocates that the initial step, with analytical evidence, is that clients review the control strategies and implement small influential instrument repairs/calibrations and operator training. This can significantly boost process productivity without the need to spend large sums of money on new capital or employing expensive, difficult to maintain ‘black box’ solutions.A simple Stage-Gate®-style approach ensures that small investments in evidence-based process improvements deliver significant benefits to mining operations.CITATION:Hill, D J, 2014. How to prioritise process improvements, in Proceedings 12th AusIMM Mill Operators’ Conference 2014, pp 307–314 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 1, 2014

By Young DJ

Gold mineralisation at the Hamata prospect is related to a series of stacked pyrite and quartz-pyrite veins associated with a number of shears which strike N to NE and dip E. Mineralisation is contained entirely within the Morobe Granodiorite close to the intersection of the Upper Watut Fault and some younger NE to SW striking faults. The prospect was originally detected in 1987 by a regional stream sediment sampling programme. Subsequent mapping and sampling outlined an anomalous zone approximately 900m long by 300m wide. Drill testing has indicated a resource of 46Mt at 0.9 g/t Au.

Jan 1, 1991

Gold mineralisation at the Enterprise Mine, 230 km south of Darwin, occurs within folded and metamorphosed sediments of the Lower Proterozoic Burrell Creek Formation adjacent to the Cullen Granite. The mineralised zone, which occupies an area of approximately 800 m x 300 m is local- ised by a moderately tight, upright symmetrical anticline which plunges shallowly southwards. The anticline has been disrupted by numerous faults on which the maximum movement is 40 m. Gold is associated with quartz and sul- phide veins which are present as saddle reefs, inter-reef veins and fault controlled reefs. it occurs within the veins or their alteration haloes, either as free gold (2 - 50 per cent of total gold content) or intimately associated with sulphides, principally arsenopyrite and Pyrrhotite.

Jan 1, 1984

By B Stewart

It has long been recognised that knowledge of the conditions existing in a mine after an incident is essential in deciding whether to deploy responders as part of the incident recovery process. Applying this knowledge in a structured manner to the assessment and the acceptability of the risks likely to be faced by those teams during response activities before authorising their deployment is an onerous task incumbent upon the person controlling the incident response. The Mine Event Management System (MEMS) provides structure and coordination in the management of mine events. It assists with the skills and knowledge for incident control teams to effectively manage any emergency or non-emergency event, be it large or small. In cases where multiple organisations are involved, the MEMS promotes effective joint operations through the use of common terminology and structure to provide seamless communication between agencies at all operational levels. The SQL-based software developed by Queensland Mines Rescue Service (QMRS) assists decision-makers to make considered options; it does not make decisions for you. When set-up, it allows the information that already exists within a mine’s Safety Health Management System that is relevant to the incident to be accessed and considered rapidly within the pressured environment of an emergency. Additionally, the incident specific questions contained within MEMS focuses the management team on gathering and assessing information relevant to the incident as it progresses. The software’s event log can be utilised as an auditable document for post incident investigation. The MEMS provides a process to properly consider the adequacy of the information available upon which decisions have to be made, to consider and acknowledge the hazards of the environments within or adjacent to which responders will need to work and to acknowledge and authorise the entry of responders into or to remain within a mine either during or post an incident occurring, once an acceptable level of risk is achieved.

Apr 16, 2024

North Eastern Russia encompasses the northern part of the Circum Pacific. The region comprises various tectonostratigraphic terranes, including cratonic blocks, fragments of volcanic arcs, accretionary wedge terranes, oceanic crust and passive continental margins. The terranes have been accreted to the eastern margin of the Siberian Craton in the Late Mesozoic. The prominent structures of the region are extended zones of the Mesozoic flysch and turbidites. Another important structure is the 3000 km long Okhotsk-Chukotka volcanic arc which marks the Cretaceous active continental margin of northern Eurasia. The youngest structure of the region is the 2000 km long Late Cainozoic Kamchatka-Kuril island arc system. North Eastern Russia is the main gold producing region of the Russian Federation. Since the beginning of recorded gold production in 1932 until 1995 the region has produced 2575 t (83M oz) of gold. Most of it, 2439.5 t, has been produced from placers. Owing to depletion of alluvial gold resources, exploration and mining emphasis is currently switching to the development of the lode deposits. At least five distinct types of the gold mineralisation are reported in North Eastern Russia - mesothermal gold mineralisation in the Mesozoic fold belts, Paleozoic epithermal gold mineralisation occurring within Omolon block, epithermal gold mineralisation related to the Mesozoic volcanics, Cainozoic epithermal gold mineralisation, gold-bearing Cu-porphyry deposits. The current paper introduces the metallogeny of lode-gold deposits of North Eastern Russia. It provides the review of the regional geology, the selected gold provinces and representative deposits with an emphasis on the mineralisation styles and distribution control.

Jan 1, 1999

By J Tickner, Y Van Haarlem, G Roach, D Abernethy, M Smith, J OÆDwyer

The development of novel technologies capable of real-time, high-accuracy, automated analysis of gold, other precious metals and mineralogy, both in ore samples and directly on process streams is reported.X-ray fluorescence (XRF) analysis is widely used for process stream monitoring of base metals. However, detection limits are generally a few parts-per-million (ppm) or larger, precluding the use of this method for monitoring precious metals. Complex interferences with other elements also limit accuracy. An XRF slurry analyser that uses advanced data-analysis techniques to resolve overlapping fluorescence lines, achieving detection limits in the parts-per-billion (ppb) range has been developed. This allows feed, concentrate and tailings streams in precious metal applications to be monitored in real-time. An extended trial of our technology in a platinum group element concentrator and laboratory tests on gold process slurries in the 0.1 - 2.0 ppm concentration range is discussed.Analysis of process stream mineralogy can provide useful information to supplement conventional elemental data. An on-stream X-ray diffraction analysis technique that provide real-time mineral and elemental measurement of process slurry streams has been developed. Both X-ray techniques can be combined into a single on-stream analyser to provide simultaneous elemental and mineralogical information. The successful trial of a combined XRDF (X-ray diffraction and fluorescence) slurry analyser is also reported.It is widely recognised that rapid, accurate analysis of grade is an essential prerequisite for optimising the efficiency of exploration, mining and processing of metals ores. The low grades of precious metals ores, such as gold and the platinum group elements, have led to fire assay becoming the predominant analysis technique. Significant drawbacks of fire assay include long turn-around times, limited absolute accuracy, high costs and requirement for skilled operating staff. For rapid measurement of gold samples, a technique that allows the gold content of large samples to be determined absolutely with high accuracy in less than two minutes using activation with high-energy X-rays has been developed. The method is non-destructive, has detection limits in the low ppb range, is capable of measuring slurries, ground or crushed solids with minimal preparation and can be made fully automatic. Initial results from laboratory trials are presented.CITATION:Roach, G, Abernethy, D, OÆDwyer, J, Smith, M, Tickner, J and Van Haarlem, Y, 2013. Advanced instrumentation for analysis of exploration, mining and process materials, in Proceedings World Gold 2013 , pp 277-282 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

Commercial or potentially commercial deposits of coal occur in Australia in strata ranging in age from Permian to Tertiary. The coals of each period tend to show a community of petrographic character and significant differences as compared with coals of other ages. In particular- many of the Permian coals are unusually rich in inertinite whereas the Jurassic and Tertiary coals are typically very rich in vitrinite. The majority of the coals show evidence of deposition in environments subject to relatively minor marine influence. Except for some Tertiary and Permian coals the content of mineral matter tends to be high. Outcrops of coals of bituminous rank appear to be largely restricted to the eastern margin of the Australian continent. In this region vertical rank gradients are generally higher than in the other sedimentary basins and uplift and the removal of cover has occurred to a greater extent. To the west of the Tasman geosyncline, coal of bituminous rank generally occurs at considerable depths (usually in excess of 1 km and in some areas only at depths of over 2 kms), and in most areas coals at shallow depth are of sub-bituminous or brown coal rank. The controls of the distribution of coal type and rank have considerable economic significance and the unusual characteristics of Australian coals, especially with respect to coal type, make the direct application of overseas technology to Australian coals inappropriate.

Jan 1, 1975

Conventional narrow vein mining, utilising hand held methods, is expensive and requires specialised miners who are becoming a rarity. Hand held mining techniques (shrinkage stoping, leading stoping and cut and fill) have the advantage that they can be selective. The methods allow continued sampling of the face, control of hanging wall conditions and are adaptable to changes in strike and dip. On the other hand, more productive longhole stoping methods can allow excessive dilution due to drill hole deviations and changes in orebody dip and can be subject to unexpected hanging wall or footwall failures. Development of small scale equipment (as narrow as 0.8m wide) used for drilling or bogging very smallaccess drives has been ongoing over the past decade. In this paper, types of equipment are examined and compared, particularly with respect to their produc- tivity, size, and working environment. The introduction of electric hydraulic equipment has provided a better working environment with reduced noise, exhaust fumes and heat. The concept of the "hydraulic cherry picker" may have application in mining steeply dipping orebodies. The system requires orebodies to be reasonably consistent in dip over 15 metre sub-level intervals. The system involves the basic concept and skills of machine and airleg mining, combined with the safety and productivity of a mechanized work platform. The platform or basket is stabilized between the hanging wall and foot- wall by hydraulic rams and is extended by a tilting hydraulic boom mounted to a small prime mover or trailer. Design concepts (including remote controlled charging of explosives, adaptation to the boom for rock cutting and the overall electric hydraulic mining concept) are put forward in the paper as a view as to how narrow vein mines will be mined in the future.

Jan 1, 1987

By B Murphy, J L. Heath

Installation of flotation equipment is a lengthy and intricate process involving conceptual design, detailed design and layout, equipment installation, equipment commissioning and handover prior to the plant commencing operation. During these steps, mistakes are often made that lead to increased costs and/or schedule delays in bringing the new equipment online.This paper presents a series of recommendations for the installation and commissioning of flotation equipment to minimise mistakes and ensure that plant production commences efficiently with a minimum of resources. The advice herein is based on lessons learnt from recent flotation equipment commissioning. It is intended as resource material for flotation plant designers, construction contractors, metallurgists and operators, and is applicable to both new and existing plants.CITATION:Heath, J L, Murphy, B and Bourke, P, 2014. Effectively installing and commissioning flotation equipment, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 399–404 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By M Doran

The Olympic Dam mine utilises 1.1 m to 1.4 m diameter raise bores for generating the initial slot void for most production stopes. Slot raise bores generally span two development levels ranging from 30 m to 50 m in height. Raise bores are reamed upward and typically leave a cap of rock equivalent to two times the raise bore diameter on the drill level (minimum 3 m). This provides safe access over the cap for subsequent production activities. It is therefore critical to ensure robust falling object protection for personnel accessing underneath, and in the vicinity of the raise bore void on the lower level. Recently, a number of mesh failures have occurred at Olympic Dam as a result of falling rock from the underside of the cap and raise walls. In addition, as Olympic Dam transitions to deeper and more challenging ground conditions, rockfall-off onto the raise bore protection mesh is anticipated to increase in frequency. This paper discusses the evolution of raise bore protection mesh used at Olympic Dam and presents results from recent site-based drop testing. This impact testing was carried out using a built for purpose object to replicate point loading and shear failure of mesh wires. Testing was also carried out on an improved mesh design which utilises two layers of Geobrugg high-tensile MINAX mesh. Results from the drop testing suggest an improvement in performance of the raise bore protection mesh is realised with the updated design.

Mar 29, 2023

In 1980 Pancontinental Mining Limited decided that while the Jabiluka uranium project was still a major focus of the company's efforts some diversification was necessary. At this time it was decided to include precious metals in Pancon's exploration and acquisition objectives. As a result the now Paddington Gold tenements were acquired, explored and developed. Today, it rates as the 6th largest gold mine in Australia and at an expanded throughput of 1.2 million tonnes per year of ore it will produce about 110,000 ozs of gold per year. Following extensive exploration activities by Pancon's Exploration Division the Operations Division continued with development drilling finally proving up a reserve of about 8.4 million tonnes at an average grade of 3.2 g/t. An in- house preliminary feasibility study was followed by a two phase feasibility study by Davy McKee. This resulted in a recommendation to the Pancon Board of Directors to develop Paddington with an annual throughput capacity of 875,000 tonnes. This paper describes the acquisition, exploration and development of the Paddington project. It goes on to

Jan 1, 1986

By Mankosa MJ, Yoon R-H

A reliable scale-up procedure for column flotation must address three important areas of column design, ie column geometry, sparging system and wash water distribution network. The column geometry is dictated by the maximum froth carrying capacity (which determines column diameter) and the bubble-particle attachment rate and particle retention time (which determines column length). The most important factor in the scale-up of an air sparging system is the ability to produce small bubbles in both laboratory and full-scale columns. Other factors, such as energy consumption and maintenance requirements, should also be considered in the scale-up of bubble generators. It is also important to design a wash water distribution system that can properly control the froth stability and maximise the column throughput. Based on these criteria, a successful scale-up example is given.

Jan 1, 1993

By Schmidt CG

Parameters affecting gold elution using the AARL process are reviewed and critically analyzed in an attempt to optimise metallurgical efficiency and minimise costs in both current and future carbon adsorption operations. Such factors as acid washing, column geometry, elution temperatures and pretreatment reagents are discussed together with eluant water quality and eluate flowrates. Hot acid washing of carbon prior to gold elution has many benefits. Besides improving elution efficiency when eluting with regional water, a hot acid treatment preheats the carbon without causing any gold leakage. Laboratory data indicated that hot acid washing reduces the mass loss of carbon during thermal regeneration. The eluate going to either zinc precipitation or electrowinning is also relatively free of troublesome impurities (organic contaminants and ferrocyanides in particular). Because of the chromatographic character of the AARL elution where an ionic strength gradient is used to inhibit the readsorption of gold, column geometry plays a significant role. While practical considerations and capital costs may restrain the length of the elution column, high length/diameter ratios are advocated in order to promote the plug flow of column eluate. From both a metallurgical and costing viewpoint, the two significant factors affect- ing the AARL gold elution are temperature and cyanide addition. High temperature and high reagent additions within prescribed limits will improve metallurgical efficiencies, but a balance between energy and reagent costs is required in order to minimise overall elution costs. As pretreatment reagents constitute a considerable portion of the total elution costs, both the addition and consumption of sodium cyanide must be carefully considered. Lower cyanide additions may be effective in certain instances, but the more practical use of 0,6 bed volume of a 2-3 per cent NaCN reagent containing 2 per cent NaOH is advocated. This is equivalent to an addition of 20-30 kg NaCN and 20 kg NaOH per ton carbon Treated.

Jan 1, 1986

The phenomenon of Instantaneous Outbursts, although not new to Australia, was sharply drawn to the attention of the local coal-mining industry by two isolated fatal occurrences on widely separated fields, both late in 1954. An outburst is the eruption of apparently solid coal from the face, aided by vast quantities of gas released from the coal, as the coal fails under mining stresses additional to its natural stressing.The gases involved are principally methane and carbon dioxide. The various factors which combine to produce outburst conditions range from external factors such as stresses arising from depth of cover and other causes, to inherent factors such as strength of coal,and its capacity to retain gases (sorption). Of the localities where instantaneous outbursts occur the Gard Basin in Southern France has had the greatest number and the most serious occurrences. By contrast, local outbursts have been minor.Experimental work into some influencing factors has been carried out by various overseas authorities and some research has been accomplished in Australia. Practices used in some overseas areas to improve safety of working are largely empirical, as are the local rules and recommendations for work in affected areas.The appearance of further outburst areas is anticipated as mining becomes more extensive and deeper.INTRODUCTION"Instantaneous Outbursts" can be described as violent eruptions of coal from the solid accompanied by considerable gas evolution. The projected coal is usually of small size, and a high proportion is pulverized, and may be carried and deposited over great distances by the gases, liberated from the outburst. This outburst coal is of bituminous to anthracitic rank, and the gas involved is essentially methane or carbon dioxide, or a mixture of both. Outbursts involving carbon dioxide are usually more violent and dangerous. The phenomenon is relatively unusual, being confined to probably sixteen known areas in the entire world, these areas comprising only portion of the coalfields in which they occur. Usually only one or two mines on each field are affected.

Jan 1, 1958

By M Fitzgerald

Fimiston Open Pit is operated by Kalgoorlie Consolidated Gold Mines (KCGM) as a joint venture between Barrick Gold and Newmont Mining. Over 110 years of underground mining resulted in the development of nearly 3500 km of underground workings including backfilled and open stopes up to half a million tonnes in size. These voids significantly complicate blasting processes at KCGM, influencing blast movement direction and magnitude. Blast movement monitoring to improve mine reconciliations was identified as an improvement project in the business plan for the geology team in 2008. Following successful trials in 2008 to 2009, blast monitoring and translation of ore blocks were implemented as a permanent grade control program from late 2009 and is now part of the Management Operating System (MOS) of the mine. This paper presents a summary of results from the Blast Movement Monitoring (BMM®) data collected to date. Ore blocks at KCGM are translated primarily using BMM® data. This data is obtained from the BMM® system which measures the movement of a radio transmitter installed in a blast pattern from a preblast position to a post-blast position. The application of the data collected by the BMM® tends to be both mine site and blast specific. At KCGM, an average distance obtained from the BMM® data within a given shot is the primary method used for translation. In the case that BMM® data is unavailable, a theoretical movement vector established from Orica Shotplus with distances gained from the historical BMM® database is used. Data is presented in an ore loss and dilution exercise for a bench undertaken at KCGM to understand the potential effects on reconciliations. Improvements that have flowed from implementing blast monitoring include improved reconciliations when combined with other grade control improvement projects. The increase in liaison between the geology and blast personnel at KCGM has been a significant improvement gained from the implementation of the blast monitoring program. This has allowed a better understanding of blast movement and the effects on ore dilution and ore loss by the mine geology team. In addition, the discussion of blasting tie-in plans between geology and blasting personnel has been improved which leads to more favourable blasting practices that take ore movement into account.

Aug 22, 2011

By K Clode, J Al-Shdifat, S Daykin

Planning for a circular economy allows for previously untapped market opportunities to be explored, resulting in new, innovative revenue generating opportunities, while also reducing environmental impacts. In particular, rare earth elements (REE) are in rising demand as they are key components of over 200 products across a wide range of applications (Xie et al, 2023) including renewable energy technologies. There is a geographical disparity in deposits, with China being the top producer, generating 70 per cent of global production in 2022 (Laboure, 2023). This single dominating source has created supply chain concentration and hence supply risks for other nations, providing a driver for finding alternative sources, such as mine-influenced water (MIW) and tailings. In this study, Isle presents a robust due diligence methodology for undertaking a global horizon scan into REE recovery technology, for a large mining company, from tailings decant water on a specific site. Previous studies of the tailings decant water at this site had shown potentially significant concentrations of both heavy and light REE, but challenges such as high flow, very low pH and high concentrations of iron had previously made recovery unfeasible. Due to these challenges, the horizon scan focused on technologies that had the potential for selective recovery, despite the challenges with water quality, and considered a range of Technology Readiness Levels (TRLs). This included an adsorption-based process that has the potential to selectively separate individual REE, and a polymer based selective flocculation technology.

Sep 1, 2024