Search Documents

By J-S Han, J-M Yao

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Shagou deposit is located along NE-trending faults within the high-grade metamorphic basement of the Xiong’er Terrane in the Qinling orogenic belt. It is a large Ag-Pb-Zn deposit hosted in the Taihua Supergroup and has proven reserves of 1.54 Mt of ore with grades of 767 g/t Ag, 13.24 per cent Pb and 4.31 per cent Zn. The hydrothermal ore-forming process can be divided into early quartz-pyrite, middle quartz-polymetallic sulfides and late quartz-carbonate stages. Four types of fluid inclusions (ie pure carbonic, carbonic, pure aqueous and aqueous) can be distinguished in quartz. Fluid inclusion, hydrogen, oxygen and sulfur isotope systematics indicate that the ore-forming fluids are initially deeply sourced metamorphic water with meteoric water gradually mixed in the later stages. Sulfur isotope data show that the ore-forming fluids originated from both the Taihua Supergroup and the sedimentary successions of the Guandaokou and Luanchuan Groups (CSC) located to the south of the Machaoying Fault. A genetic model of the Shagou deposit is proposed as follows: CSC subducted northward along the Machaoying Fault beneath the Xiong’er Terrane during the Mesozoic collision between the North China Craton and South China Block. Subsequent dehydration resulted in the devolatilisation of fluids rich in CO2. These fluids migrated upwards, reacted with the Taihua Supergroup and formed the Shagou deposit.CITATION:Han, J-S, Yao, J-M and Chen, H, 2015. Fluid inclusion and isotopic constraints on the mineralisation of the Shagou Ag-Pb-Zn deposit, Henan Province, China , in Proceedings PACRIM 2015 Congress, pp 615–618 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

The extra information brought by further drilling may seem necessary to achieve control over block grades if elementary estimation techniques are used. However a geostatistical study of an Australian deposit shows that better estimation techniques at the end of the first drilling campaign are sufficient to achieve required control.Subsequent drilling would be essentially wasteful.

Jan 1, 1975

Using a cylindrical hydrocyclone with a long vortex finder as the separator, a batch sizer was developed for the fast comparative sizing of the coarse solids normally encountered in mineral pulps.Operating times as short as 2 or 3 min gave separations ranging from 16 mesh down to the subsieve sizes.Reproducibility was good and sensitivity was adequate for most applications.

Jan 1, 1968

Important factors in dredge design are the estimation of total head, and the determination of flow in and around suction nozzles and in pipe lines. Total head for the dredge pump is calculated from velocity, static, and friction heads. Flow into suction nozzles depends on whether hydraulic jets or mechanical cutters are used, and on nozzle shape. Design of pipe lines depends on the transportation characteristics of the pulp, skin friction, swirl, and the avoidance of cavitation. Measurement and control of flow is important.INTRODUCTIONEconomic deposits of heavy minerals along the east coast of Australia occur in frontal dunes, which are normally unconsolidated and granular, or in hind dune areas which may contain indurated seams interspersed with loose material. In working frontal dunes, dredging depths are usually shallow since values do not persist for more than a few feet below sea level. However, the controlling factor in dredging the hind dune areas is the level of the water table and suction dredges may be designed to mine to depths of 120 ft, or even more, if necessary.In previous applications of suction dredges in the industry attention was directed primarily towards production and there was only limited research on fundamental techniques. However, with lower grade deposits now forming the major ore reserves, production levels and profit margins will fall unless more efficient dredges are developed.For satisfactory design of dredges it is essential that the total head be accurately estimated and that detailed information of the principles of flow in and around suction nozzles be determined. This paper presents information gained from field experience and laboratory investigation on these aspects.

Jan 1, 1962

Perhaps one of the most important conferences or symposia which our Institute has conducted, was the joint Aus. LM.M./AJ.M.E. meeting held in Canberra in May 1978, with the theme International Resource Management (Woodcock, 1978).We were privileged to witness active participation in the meeting by outstanding personalities from the mining and metallurgical industries of Australia and New Zealand, the United States of America, Canada and the United Kingdom and to hear addresses on subjects of international significance to the mining and metallurgical industries.Our Institute is one concerned with professionalism.The principal objects of The Institute as described by our founders include, "promoting the arts and sciences connected with the economical production of the useful minerals and metals, and the welfare of those in the industries, by meetings for social intercourse, and the reading and discussion of professional papers, and to circulate by means of publications amongst its members and associates, the information thus obtained".Sir Maurice Mawby (1968) said in his Presidential Address to the Institite, "the most important aspect of these objects was the promotion of the arts and sciences of the mining industry".Why is it then, that a large proportion of the papers given at the meeting in Canberra dealt with world wide social aspects of the mining and metallurgical industries, rather than the technology, the arts and sciences of mining and metallurgy as principal factors in international resource management?The answer is quite simple of course, and that is that the social and political factors are the principal factors which create the demand for basic raw materials and in the long term determine the costs and prices of the commodities which our professional abilities are drawn upon to produce.

Jan 1, 1979

By Madgwick J. C

Microaerobic biodegradation oflow-grade manganese dioxide slurry tailings was demonstrated in enrichment cultures treated with dilute molasses at 30°C and pH 5·8. Supplementary nitrogenous nutrients, yeast extract addition and pH adjustment were not required.Continuously stirred, air-limited reactors were superior to still intermittently agitated cultures, in that, at 5 per cent (w/v) MnOz tailings and 5 per cent (w/v) molasses, the yield of 0.12 g Mn++/g molasses, the rate ofleaching of 1·06 g Mn++/l/d and a recovery of Mn++ of 58 percent from MnOz were 2·8 times, 1·7 times and 1·9 times greater, respectively. The best compromise in yield (0·45 g Mn++/g molasses) and rate ofdissolution (0·73 gMn++/l/d) was at 1 per cent (w/v) molasses in a stirred reactor.Where leaching organisms were separated from sterile ore by a bacteria impermeable membrane leaching was shown to be some 20 per cent due to diffusible metabolites and 80 per cent due to a direct contact between the bacteria and the ore particle's surfaces.

Jan 1, 1986

Ensuring the success of a major resource development project, whether in the Gippsland Basin or elsewhere, is typically both a complex and costly process. It is therefore imperative from the point of view of the proponents of such a project - and in particular the financiers - that everything possible be done to minimise administrative confusion and delay in the establishment phase of the project, and to put systems in place which enable the project to run smoothly and efficiently in the later stages of its development and operation. An essential element in this process is ensuring that the project management is able to come to terms with and deal effectively with the relevant planning and environmental laws.

Jan 1, 1992

Possibilities and Working of the Specific Agglomeration of Fibrous Materials and Residues Plant based fibrous materials are becoming of increasing interest in a multitude of industrial applications. Main advantages are the specific lower energy demand and virtually closed CO2 cycle, excellent mechanical properties based on low density as well as a high level of recyclables. In contrast, processing and handling of such materials is associated with a number of challenges. These challenges are mainly related to specific morphological characteristics in correlation to fibre length and structure (branching and splices). Specific problems in further processing steps including transport, dosage or storage for natural fibre compounding, result from form-locking bonds leading to burling, clusters or plaits. Technologies of fibre processing are well known, but other than textile based technologies they generally result in intermediate goods which do not allow direct industrial application. The investigation to be presented is based on results of recent research activities and shows two possible technical solutions of innovative fibre agglomeration procedures. These methods allow the conversion of middle to long fibres into a form, which eases further processing and dosage significantly and therefore allows free flowing too. The procedures are based on the working principles of rolling and winding technology. Within the work, both of the patented methods and their respected lab-scaled devices will be described. Further, results will be shown for an up-scaled rolling agglomeration unit applying the developed principle and consisting of multiple process zones. Possible variations of the resulting product characteristics and the impact of different process parameters will be discussed based on the trials with natural fibre (hemp and flax) agglomeration. As a main outcome of the research, product qualities can be supplied according to the requirements of the specific application in correlation to agglomerate strength, porosity or form. In conclusion, recent developments for specific methods of characterization will be depicted.

Sep 13, 2010

The presence of undetonated explosives in a rock face after firing constitutes a hazard which can result in a fatal or serious accident if undetected before drilling commences.Most accidents caused by drilling into explosives are the result of failure to examine the working face properly and lack of care in subsequent drilling operations; it is not always realized that explosive may be left in the butts of holes or may be driven into cracks or crevices in the rock.Obviously the best means of preventing accidents of this nature is to adopt methods of drilling, charging and firing which will reduce the hazard to a minimum.There are three ways in which undetonated explosives may be left in the rock face, namely:1. Misfires.2. Cut-off shots.3. Incomplete detonation or failure of the charge to propagate throughout.MisfiresNo attempt will be made in this paper to deal fully with the question of the prevention of misfires, as apart from the fact that most of the preventive methods are well known, it is believed that if the miner receives his explosives and means of initiation in good order, and proper care is taken in their use, the failure of a charge to fire will be a rare occurrence. The provision of central fuse capping stations on mines has gone a long way towards the elimination of misfires caused by the mishandling of safety fuse anddetonators.

Jan 1, 1956

Suggestions have been made at various times that there may be a recurrence of lodes similar to those at Kalgoorlie in the country to the south of the Golden Mile, but, so far as is known, there has been no geological evidence to support these suggestions apart from the possible extension of the younger quartz-dolerite greenstone in this direction.Geological mapping carried out by the writer in the Coolgardie district in 1946, provided some additional geological evidence to support this claim, and the ideas then held have since been expanded and are now considered to be sufficiently advanced to present them as concrete suggestions. As will be seen from the following pages, the critical area for lode prospecting is Hannan's Lake, where the basement rocks may include younger quartz dolerite greenstone, which, although perhaps distributed over a smaller area than at Kalgoorlie, could, on structural grounds, have a similar fracture system and similar ore deposition.There is little need to stress the importance discoveries in this area would have in prolonging the life of the field, and stimulating the post-war gold mining revival.Previous Work: Only the publications having a direct bearing on the preparation of this paper are given in the list of selected references, but the writer is very conscious of the fact that much other geological work has been carried out in the Kalgoorlie district since its discovery, by the W.A. Department of Mines, by mining companies, and others, all of which has contributed to the present knowledge of the field, and acknowledgment of the value of this work is given herewith. In presenting the suggestions in this paper a broad structural control of ore deposition is assumed, but this has already been established in other parts of the goldfields of Western Australia, including adjacent areas. In the early nineteen thirties, the Western Mining Corporation commenced work on the basis that there was a close relationship between geological structure and auriferous ore deposition, and a similar approach was first made by the Geological Survey of Western Australia in the South Yilgarn in 1935. These ideas were further developed during later surveys, particularly in the North Yilgarn and the Mount Margaret Goldfield.During the Coolgardie Survey in 1946, broad structural mapping was done in greater detail than before, and the structural ideas were implemented and further developed, leading to some success.Other work to which particular acknowledgment is given is that of Stiltwell, Gustafson and Miller, Forman, Prider and Finucane, at Kalgoorlie, and that of Honman in the Kalgoorlie-Coolgardie district, references to which are given at the end of this paper.Valuable constructive criticism of this paper has been given by Professor E. de C. Clarke and Dr. R. T. Prider, of the University of Western Australia.

Jan 1, 1950

A poured slag bottom is universally considered to be the best type bottom for copper reverberatory furnaces. It is impervious to molten matte and ready for immediate use.When molten slag is not available a monolithic silica bottom is the second best; such a bottom has been adopted at Mount Morgan. The laying of such a bottom is a phase of smelter construction on which so little real information is obtainable that a day to day record of such a recent example as Mt. Morgan's 19 ft. x 40 ft. reverberatory may be of interest. The work was done under the direction of E. Pesout, of McGill Smelter, Nevada. PREPARATION OF THE BOTTOMA 26-inch bed of closely packed firebrick with sand-filled joints was first laid on the clean, dry concrete foundation and the whole dried out by small fires maintained on the brickwork for several days. Ninety tons of silica sand was meantime thoroughly dried and stored in clean drums. This sand must be low in FeO and CaO and contain about 95% Si02 , the majority of which should be present as tridymite. This form of silica shows little expansion at high temperatures, for it is the form stable between 870° and 1470° C.Its presence thus minimises disturbance to the bottom by the expansion which, during the burning in, would mark the transformation of quartz to tridymite.

Jan 1, 1939

Development of Underground Gold Processing Plants Underground gold processing plants have potential advantages over traditional surface installations related to a smaller environmental footprint, reduced capital and mining costs, improved security and increased value of the product delivered to surface. The concept of processing gold ores on the surface is the traditional paradigm. A process of pre-concentration of ore underground is likely to result in a major shift in operating costs. In particular, run of mine ore or a large proportion of it will not need to be transported to the surface. As a result, environmental and financial benefits are likely. Underground plants are likely to be pre-concentration systems where the process product is a high-grade concentrate and tailings for stope backfill. Units will be either static or modular. Concentration methods will be gravity and/or flotation or leach based. This paper discusses the development underground gold plants from early concept, through to the world's first operational unit, a newly commissioned unit and the technical basis of a fully modular system.

Sep 13, 2010

Up to 19 chemical parameters were studied in flotation pulps in six Australian lead-zinc concentrators with the aim of obtaining a better understanding of the nature of, and changes in, the chemical environment. This paperdiscusses pH, redox potential, and oxygen concentrations, which were all measured continuously.Two plants operated at natural pH in slightly acid circuit and one at natural pH in alkaline circuit, and pH was stable at all these plants. In two plants varying amounts of cement fill were present in mill feed and pHwas variable. At the other plant pH was controlled with soda ash and lime.Redox potentials became more positive as the pulp passed through the plant. The minimum change was 20 mV and the maximum about 250 mV. Potentials tended to be variable at any point early in the circuit, but were more stable later on. In some plants reagent additions had no noticeable effect on redox potentials. However in the two plants operating in acid circuit the redox potential of .zinc rougher feed was markedly affected by changes in copper sulphate addition rate. Sodium sulphite additions had an effect at other plants.Oxygen concentrations in grinding circuits tended to be low (30 per cent of saturation) and very variable. Flotation was usually conducted in pulps at least 90 per cent saturated with oxygen. Addition of sodium sulphite had a marked effect on oxygen content in one plant, but less effect in two others.Statistically significant relationships were found in some plants between pH and redox potential, redox potential and oxygen saturation, and oxygen saturation and pH.Improved control of copper sulphate and sodium sulphite additions could result from applications of this work.

Jan 1, 1970

The presence of gold or tin in a particular place in payable quantities may be suspected from geological and prospE;cting reports. It behoves the engineer by judiciously spaced boreholes or pits to establish whether the place is exploitable with profit, and it is the purpose of this paper to set out the ways in which this is done. The various types of deposit to be considered occur in Malaya, Thafland and Borneo, in which countries the writer spent four years in estimating alluvials.The methods described were used in actual practice both by the writer and previous engineers for the same company. The subsequent exploitation of the alluvials evaluated by the methods given below shows that the recovery was as good as, and sometimes higher than, expected. No claims are made to the originality of the methods, but it is 'felt that they may be new to some engineers and< interesting to others contemplating alluvial testing.

Jan 1, 1942

Amongst the unavoidable studies of the mining engineer who desires to reach the maximum efficiency, is the subject of patents. With the fundamental principles of the patent laws of this and other leading countries he should of course befamiliar, but still more should he keep abreast of that practical knowledge which will enable him to act or advise wisely when the patenting of a new invention, or the sale, purchasing, or adoption of a new patented machine or process becomes amatter for consideration. As every engineer worthy of the name is an inventor and more particularly every mining engineer he has a direct interest in watching the progress of legislation and administration concerning patent monopolies.His worldly prospects may indeed, to a considerable extent, depend upon the defeat of bad patent laws and the removal of incompetent officials, or the appointment of better ones. Better patent administration is always in Australia a valid requirement, and until engineers generally take up and press the demand, bad administration is likely to continue. Even though every engineer is not a patentee, nevertheless his interests in patents must always be direct and powerful, and ignorance or apathy in regard thereto must inevitably injure either his own interests or those of his employer. When we consider the tens of thousands of mines scattered through Australia alone, on everyone of which there is expensivepatented machinery, and when we consider the thousands of...

Jan 1, 1901

By A Brzovic, E Córdova

In an underground mine, different mining activities such as undercutting and cave progression generate redistribution in the present in situ stress field, and these changes are represented in the rock mass through induced seismicity.In order to study and analyse the induced seismicity generated in El Teniente, a block model was developed to account for the dissipated seismic energy through different areas of the mine from 1992 to 2015. More than 2.1 million seismic events were unified and classified in 3D in order to be used for the interpolations. The resultant model variables account for the accumulated energy releases in a monthly time resolution, and provide the ability to intersect different 3D entities with the stored information in the blocks, and estimate the energy evolution inside these entities.The generated model was used to analyse the geotechnical variables that determine the seismic response for the rock mass in the mine, such as geometry and direction of advance of the undercut fronts, lithological domains, and to study the ‘work’ the rock mass needed to go through in order to generate caving in areas with different stress settings.A specific area of the mine under high-stress conditions was analysed by studying the seismic energy associated with two subsidence caves interacting around the project, the modelled lithology. Using the same approach two adjacent projects are analysed to understand the released energy from the rock mass based on different stress and geotechnical settings for each project.CITATION:Córdova, E, Brzovic, A and González, R, 2016. Analysis of progressive seismicity and its correlation with geotechnical variables at the El Teniente Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 835–844 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

Very little has been written about the discovery and early history of prospecting of ironstone deposits in the Iron Knob-Middleback Range area of South Australia, the main source of supply of ironstone (hematite) for the Australian steel industry, and scanty though the record is, much of it is wrong or misleading.With the help of several people, to whom acknowledgement is made at the end of the paper, the writer has unravelled some of the story, but not the whole story. It is hoped that publication of this paper will stimulate interest in others, who may be able to supplement this account from family records, from the files of newspapers, or from archives.

Jan 1, 1969

At an early stage of the examination of most prospects, samples are taken; and the sample values obtained play an important part in determining the subsequent history of the prospect. It is, therefore, important that. eveJJy effort should be made to interpret asfully as possible the meaning of the observed results. In this connection, it is suggested that examination of the assay values of mine samples by simple statistical methods may bring to light information of considerable value, which might otherwise be missed.Although expert statisticians may derive more information from the available data, those who are, like the writer, less proficient mathematically, may also benefit by applying quite simple statistical methods. At least they will develop a useful habit of thought bywhich they become aware at all times that sampling results only provide estimates of the truth, but that an assessment of the precision of such results may be possible. The object of this paper is to provide some evidence of. the truth of these statements, by theuse of a few very elementary statistical calculations.General.The idea that any mine sample is subject to error from a variety of causes is a very familiar one. Doubt always exists with regard to the representativeness of a perfectly cut sample, and other errors may arise through imperfections of sample cutting, crushing, splitting and assaying. Some causes of error may give rise to "constant" errors, others may cause variable but one-sided "systematic" errors, and others again may bring about variable results without any tendency toward bias on the average. In statistical language, mine sample values are subject to errors which may have either assignable causes or chance causes. The former are those which can be isolated, or should be capable of isolation, while the latter are those remaining when all assignable causes have been removed. A single constant assignable cause brings about bias in all results, and one or more than one variable assignable cause brings about variation between individual results and perhaps an overall bias. The system of chance causes that would remain if all assignable causes were removed would cause variation between individual results but no overall bias. There is no sharp practical line of distinction between the two types of cause) of error; nor is it ever possible by any method of statistical analysis to be certain that there are no assign...

Jan 1, 1950

Were it simply a matter of extracting tin from the simple tin sulphide, the proposition would undoubtedly be simple enough. When, however, other valuable metallic sulphides are combined with the tin, and it is required to separate these intomarketable products, then the proposition becomes somewhat complex, and such is the case with the class of material of which I am about to write. The locality where it occurs is Howell, New South Wales, and chiefly at the Conrad Silver-Lead Mine. The tin sulphide occurs chemically alloyed with copper, iron and other metals associated with galena, pyrites, mispickel, blende and silver sulphide in varying proportions, and generally in a gangue of highly crystallised quartz.Several varieties of tin sulphides occur, and from the following analyses of three minerals, these being specimens specially selected free from foreign matters, it will be seen that the chemical composition is somewhat complex.

Jan 1, 1902

This method determines tellurium at concentrations down to 0·01 p.p.m., with geochemical accuracy. Tellurium is volatilized from the rock at 800°C in the presence of sulphur from decomposing pyrite, condensed, dissolved, and finally determined by atomic absorption in a long tube burner. The distribution of Te is shown near some gold lodes at Kalgoorlie. Lastly, a method of synthesizing Te-free pyrite from sulphur and ferrous sulphate is described.

Jan 1, 1969