Search Documents

With the progress of modern mining engineering, one of the features of which is the mining from greater depths and the hoisting of greatly increased loads, it becomes a matter of increasing importance that the engineer should be able to determinewith some degree of precision the character of the strains on the hauling rope. But a wire rope is a complex structure; it is made up of spirally-twisted strands, which in turn are composed of spirally-twisted wires, and it is not particularly easy to say exactly what happens when this "doubly-twisted structure is wound round a drum or over a pulley.. The difficulty has been generally evaded in ordinary practice by the simple device of adopting a large factor of safety for the rope-usually from 8 to 10-a factor which experience has shown is sufficiently large to cover the bending strains set "up when the rope is passed over pulleys of the sizes commonly considered appropriate.When, however, we add the stress due to the bending of the rope to the stress produced by" the direct pull, we find that the actual factor of safety is usually more nearly 4 than 10, and frequently the bending stresses in the rope are so large compared with the simple tensile stresses that their neglect may easily lead to disastrous results when dealing with problems a little out of the common run. Common Empirical Rules.-It is always "recognized that the bending of a wire rope round too small a pulley is likely to do the rope serious injury, but as it is desirable in ordinary winding operations to reduce the inertia of the moving parts to a minimum...

Jan 1, 1907

By Bloom M. S

Epithermal vein and breccia hosted Au mineralisation at the Kerimenge prospect, in the Wau district, Papua New Guinea, occurs within a block of multiply fractured dacite porphyry of Pliocene age, and is localised on intersecting regional fault structures, marginal to the eroded vent of a Late Pliocene-Pleistocene maar volcano (diatreme).Au mineralisation is primarily controlled by the steeply dipping Kerimenge Fault zone, which hosts a basal zone of silicified breccias,transitional laterally and vertically to networks of fracture controlled veins.Early quartz+pyrite veins, deposited from CO2 rich, NaCl saturated, boiling fluids pre-date the main phase of Au mineralisation. Four stages of Au bearing vein mineralisation have beenrecognised. Quartz+sulphide veins (stage 1) and partially coeval quartz+sulphide+carbonate+ adularia veins (stage 2) occur marginal to silicified breccias, and are associated with quartz+sericite+pyrite wallrock alteration. Similar depositional conditions prevailed for stage 1 and stage 2 mineralisation. Mineralising fluids underwent two stage boiling at temperatures of 145 to 2300 C. Boiling resulted in the loss of approximately 3 wt.% CO to the vapour phase. 2 Fluid salinity was probably I wt.% NaCl or less.

Jan 1, 1990

The light microscopic study of the physical structures of coal and associated mineral matter is an important technique in providing information on the characterisitics and possible behaviour of coals in industrial processes. However the ultrafine nature of coal and mineral particles together with the limits of resolution of the light microscope restrict such studies. Scanning electron microscopy (SEM)with its better resolution and higher magnifications is the means by which further information on coal properties can be obtained. An associated energy dispersive X-ray specrometry (EDS) method allows non-destructive in-situ chemical analyses to be carried out at the same time.

Jan 1, 1989

By Mroczek C. R, Evans D. A

Renison is a world-class ore deposit that has been mined for over 100 years. It currently has reserves of 5.06 Mt @ 1.88 per cent Sn and a projected mine life of 8.5 years. Recent advances in the geological understanding of the deposit have been associated with detailed structural and geophysical investigations accompanied with the discovery and exploitation of the Rendeep orebodies. Mineralisation is linked to the forceful emplacement of the Devonian Pine Hill Granite that resulted in a complex brittle (-ductile) deformation of the Eo-Cambrian host stratigraphy. Dilation jog development on the Federal-Bassett Fault in the Federal and Rendeep areas provided access for cassiterite-rich magmatic hydrothermal fluids responsible for carbonate replacement Mineralisation.

Jan 1, 1997

Computers and other microprocessor technology lead the world of technological change. Nevertheless, the real advances in the world at large are not necessarily in the computer industry, but in the industries whose economics benefit most by the advances that this computer revolution makes possible. The minerals industry has always been in the forefront of this advance. Technological change in the era preceding the industrial revolution, and the mining industry's part in it, provides an instructive lesson for what is happening today. Strong parallels can be drawn for predicting future advances. With each technological advance allowing more efficient production comes a re-alignment of economics - absolute and relative changes to prices, to quantities demanded, and to other market characteristics. This re-alignment applies not only to the mineral industry, but also to the world at large. Adaptability, rather than technical advancement per se is the key to survival and growth in a changing world. 'Adaptability' as a concept is easy to support. As an operational philosophy it is not so easy to implement. As a goal for planning, it is much harder to quantify. A fixed scenario of a future world may provide helpful guidelines, but a scenario that demands adaptability to an uncertain future world is much less definite. Of course, everyone else in the world is also uncertain about the future, and they are making their plans using different assumptions. This virtually guarantees that our future will turn out different to our expectations. This is in part what Hayek (1945) calls the 'knowledge' problem. Until now, most of the planning and technical research undertaken in the world has ignored this problem. This ignorance is a luxury that we can no longer afford. The paper looks at the history of technological change and highlights the characteristics of successful technological revolutions. 'Adaptability' to unforeseen circumstances is the key to success in this environment. The paper examines the knowledge problem from the perspective of the mineral industry, and suggests a number of directions for maximising the returns from application of computer technology in this important area.

Jan 1, 1995

By Hyslop W

It is shown that coke has a major influence on the pattern of operation and on the aerodynamics of the blast furnace and that the physical and chemical characteristics of coke, at each stage in the furnace, determine its ability to satisfy requirements for iron production and coke economy. Analysis of coke sampled from operating furnaces is compared with furnace behaviour. The available data suggests the importance of segregation, strength, size change and chemical degradation of coke on furnace performance. Correlations are presented for coke breakdown ratio as a function of coke rate and hearth diameter which shows that breakdown increases with hearth diameter and with decreasing coke rate. It is also shown that the Micum tests do not reflect the coke strength in a predictable way and that solution reactions appear to play an important role in giving rise to a pitting effect on the cell walls of the coke with the resultant deterioration in coke properties. The catalytic effect of activating substances, such as alkalis, is noted and results are presented which show the effect of carbon solution on the coke strength. The importance of coke in the stack and in the bosh is discussed and flooding results are presented for BSC furnaces which show the probable driving limits for the furnaces considered. It is also shown that coke sampled from different tuyeres in a furnace gives quite different flooding limits. Other applications of the coke test work at BSC are also noted and the relevant objectives listed.

Jan 1, 1975

There is a Chinese saying-may you live in interesting times. Certainly we do tod.a~our mining professions. We are, of course, totally dependent on a' healthy mining industry for the chance to practice our chosen professions, and for our Institute.Let us look at one of the more interesting facts. The mining industry now accounts for some 50 per cent of Australia's exports.This massive earning of foreign exchange is the key to keeping our increasing overseas debt in check. Furthermore, mineral production..including petroleum, saves us a large amount of foreign currency by providing essential minerals, including energy minerals, for local consumption.With such fundamental inputs to our economy, any primary school student, any child in fact, should be able to see that the mining industry and mining professions are very important to our nation. Yet the average citizen is unaware of this simple fact as they enjoy their high standard'of living and think that we are still living in the lucky country.Therefore, it is most interesting to me that the average citizen, and most of our politicians, seem to hold mining and miners in low esteem. I use the term miners to describe all those important people, like us, who work in the mining professions, and are employed by, or are dependent on, the mining industry.So why are we miners in this paradoxical situation of doing wonderful works, being the backbone of the country, and yet being held in low regard by the very community we underwrite.Truly-it is interesting-or did the Chinese mean intriguing?It is indeed paradoxical that we are the rare people who open up the land, borrow small parts of it for a relatively short time to harvest the mineral crops, then return it to the community for other uses; and when we return the land back to the community at large it should be in better shape than when we started. There will be infrastructure - roads, airstrips, supplies of water and power, parks and housing-all left behind after mining.These benefits to the community are ignored while our critics focus on the small scars on the landscape which sometimes cannot be healed at reasonable cost; and yet, if we allow time, nature usually heals the small scars anyway. Look at New Zealand, particularly the Coromandel Peninsula which was intensively mined and logged; now it is covered with secondary growth and stark pine plantations. Remember that mining scars are infinitesimally small when compared to urban sprawl or clearing of land for farming and grazing, or highways, or the area of most national parks.Thus, miners are important citizens economically, and we are the majority of the few who actually practice the principles of multiple land use.What are the consequences of our image? They are serious in that the poor image we seem to project, discourages many people from becoming involved in, or supportive of, our industry. This brings me to my theme for the year: Students, Education and Communication - the Key to our Future.

Jan 1, 1987

By Clift N

Lead concentrate from the Isa and Hilton lead-zinc concentrators of Mount lsa Mines Limited is smelted at Mount Isa to produce a lead-silver bullion. This bullion is cast into four tonne blocks and shipped to Britannia Refined Metals Co Ltd, NorthDeet, England and to plants in Asia for refining and marketing. The traditional treatment stages at Mount lsa are sintering, smelting, and drossing and casting, with some of the sinter plant feed being pre-treated through an Isasmelt plant.A commercial scale lsasmelt based lead smelter was commissioned in early 1991.

Jan 1, 1993

A survey of leaching systems for the dissolution of gold has been undertaken and their advantages and disadvantages evaluated both from their effectiveness at leaching and their compatibility with carbon- in-pulp (CIP) and resin-in-pulp recovery. In the near future it is almost certain that cyanidation in some form will remain the leaching system of.choice although economic and environmental pressures could see the introduction of other leaching systems particularly for treating refractory gold ores. The most likely alternative leaching systems appear to be acid chlorine, acid thiourea and ammoniacal thiosulphate. INTRODUCTION High grade reserves of readily recoverable gold ores are gradually being depleted which, inevitably, must create a greater awareness amongst gold producers, of the efficiency and, in some cases, the suitability of present day metallurgical processes for treating low grade, complex and refractory deposits. One of the key steps in the extraction of gold is the dissolution of the metal using chemical reagents which, ideally, should be cheap or recyclable, selective, non-toxic and compatible with down-stream recovery processes. In practice, meeting all these critera is difficult - if not impossible - particularly in view of the stringent environmental impact requirements which must be met Nowadays.

Jan 1, 1982

Swedish sulphide mining is presented. Dry filling is described. Fill properties with and without cement addings are dis- cussed in relation to various studies in la- boratory and in situ.

Jan 1, 1973

By Watt JS

The ash content of coal can be determined using radioisotope X-ray techniques. A number of overseas applications of X-ray techniques are described; however these suffer from the disadvantage of either not compensating for iron variations or, if compensation is used, using X-rays of low penetration with consequent sampling difficulties. Current Australian Atomic Energy Commiss- ion (AAEC) research on X-ray techniques is aimed at overcoming the limitations of these methods. The AAEC method involves making measurements proportional to mass absorption coefficients of X-rays in coal at two energies. Calculations and experiments with X-rays up to 35 keV have shown that ash content can be determined to about 1 wt.%. This work is being extended to higher X-ray energies to enable the technique to be used directly on a conveyor belt or in a hopper. Neutron techniques can be used to measure the concentration of specific elements such as carbon, hydrogen and silicon in coal. Their con- centration is correlated to the coal parameters of interest. Methods of moisture determination based on hydrogen measurement and ash determina- tion based on silicon and aluminium measurement are described. Energy content can be determined accurate- ly by analysing the carbon content of coal

Jan 1, 1978

By Simpson JF, Murrie SJ

In determining new areas for slag disposal a foamed slag aggregate has been developed for use as a skid resistant material. The foaming of the slag does not rely on the use of water, but rather on the slag chemistry. Laboratory test results indicated that a product having good skid resistant properties has been prod- uced. A section of road is being assessed for performance of the aggregate in a surface dressing application under heavy load. The results from the test section after seven months have shown that the foamed slag is suitable for this application. Further test sections are now being considered.

Jan 1, 1979

By Kelley BC, Filmer AO

The chemical oxidation kinetics of sphalerite by Fe(III) was studied at various temperatures and size fractions in sulphate media. The kinetics of Zn extraction followed a pore diffusion control mechanism with an apparent activation energy of 54-58 kJ mole. This figure, although high for a pore diffusion control process, is consistent with other studies carried out in sulphate media. An empirical statistical model, relating the extraction time to % Zn extraction, average particle size and temperature, is described by log 1 = 12.22 - 0.017% Ext. - 1.76 log D Av t - 2954 T Parallel studies were also carried out investigating the biological oxidation of sphalerite utilizing the acidophilic autotrophic bacterium Thiobacillus Ferroxidans. The effect of such kinetic parameters as pulp density, particle size and Fe(III) on bacterial growth rate and consequently zinc extraction rate, were studied and where appropriate, optimum conditions for bacterial growth were specified. Based on the results of chemical and biological leaching studies, it was apparent that rapid zinc extraction from sphalerite was predominently due to oxidation by Fe(III). The biological oxidation process catalyses the oxidation and regeneration of Fe(III). The proposed combined chemical-biological leach system was simulated in semi continuous fashion. The sphalerite oxidation rates obtained in this system were similar to that predicted by the chemical leach empirical model. 1. Senior Research Metallurgist, CRA Research, Boolaroo, N.S.W. 2. Group Leader-Hydrometallurgy, CRA Research, Boolaroo, N.S.W. 3. Senior Research Scientist, Biotechnology Australia, Roseville, N.S.W. 4. Senior Experimental Officer, Biotechnology Australia, Roseville, N.S.W.

Jan 1, 1986

By Bhattacherjee A, Makesh S

Mechanised sub-level stoping is one of the most widely accepted stoping practices followed in base metal mines in India. As a general practice, blast-scheduling of rings in these stopes is done either heuristically or randomly which leads to a high fluctuation in ore grade when drawn and delivered to the mill. In this paper, dynamic programming has been investigated as an optimisation technique for optimal blast-scheduling of rings. A microcomputer based dynamic programming algorithm has been developed in C language which runs under the UNIX environment. A case study based on Indian mine data is presented to demonstrate the application of the dynamic programming concept and use of the developed software. It is concluded that dynamic programming can be used as a production planning tool in Indian mines practicing sub-level stoping and following heuristic/random approaches for blast-scheduling of rings.

Jan 1, 1995

By M McGeough

Following the success of calcrete sampling at Challenger, calcrete sampling has been widely adopted as the primary exploration technique for gold exploration, in the Gawler Craton. Calcrete is uniformly distributed over large areas and produces discrete gold anomalies. This allows drilling to focus on specific gold anomalous targets. However, despite widespread use of calcrete sampling, very little is known of the origin of calcrete in the Gawler Craton, and the link between calcrete gold anomalies and primary mineralisation. In an attempt to understand this association Lisa Gibbons recently completed an honours project at the Old Well Prospect approximately 45 km SSE of Tarcoola. Her work is part of a collaboration between CRCLEME, MESA and MIM Exploration. At Old Well, a calcrete anomaly (>10 ppb Au)covers an area approximately 7 km x 2 km with a peak value of 97 ppb Au. The study looked at the regolith as a whole, processes of its formation and nature of mineralisation within it. She was able to combine previous calcrete and drilling results with her own observations. The results from this study highlighted problems in relating surface calcrete anomalies to in situ gold mineralisation.

Jan 1, 1998

The large rotary blast hole drills for hole sizes of 250 to 375 mm in diameter have been utilized by large open pit metal and coal mines for production drilling all over the world. The design of such rotary drills is in most cases about two decades old and it has not been done much in order to apply a modern technology on rotary drilling. The most modern large rotary drill, Tamrock RI 10, consists of an advantageous rotary head with a squirrel cage AC motor controlled by a frequency converter, a beneficial mast structure with a possibility for inclined drilling, hydraulic driven, independent crawlers, and a modern ergonomic cabin to provide a comfortable working condition for the oper- ator. Several automatic features are available as options. The rig has been designed to be operated by one man only. With this modern rig the produc- tion rate can be increased and production cost kept on a low level.

Jan 1, 1989

The standard charge weight scaling laws imply that only one particular delay (that possessing the maximum instantaneous charge) contributes to the ppv. However, the present analysis clearly demonstrates that a varying number of blastholes contributes to the ppv. This number also increases with distance, x, between the blast source and the detector, and is caused by waveform broadening due to attenuation. Thus the operative charge weight, itself, is also a function of the distance, and so makes the standard charge weight laws difficult to implement. If the delay time scatter is neglected, then, under certain conditions, relatively simple expressions can be derived for the ppv magnification, FN, as a function of the number, N, of blastholes. When the influence of delay scatter and random fluctuations in each blasthole vibration is included using Monte Carlo simulations, then, to a first approximation, the condition FN=KNx applies, where KN is a constant dependent upon N. Unfortunately, however, for any particular blast this condition cannot be distinguished from the standard charge weight scaling law. The dependence of ppv on N would only be apparent if blasts of differing N were to be compared in an otherwise identical environment. Since this situation is very difficult (if not impossible) to realise, then the influence due to N, although significant, goes largely undetected. Another problem associated with standard charge weight scaling laws is the difficulty of accurately assessing the appropriate charge weight, even if attenuation broadening is neglected. For example, if a number of blastholes are very close, then they experience a vibration interaction which is non-linear. However, if the same blastholes were to be widely spaced, then the separate vibration signatures add linearly. The standard charge weight scaling law fails to distinguish between such linear and non-linear regimes. Unfortunately, in many production blasts, both regimes exist throughout various portions of the blast spatial pattern and so makes it difficult to determine the operative charge weight. The solution to the combined influence of waveform broadening and linear/non-linear interactions will obviously require substantial future research. A possible solution may be found in the use of numerical dynamic codes.

Jan 1, 1990

With the sinking of the new No. 3 Shaft and the increasing depth and northward movement of the mining operations, improved ventilation of the mine workings became necessary and it was decided to sink a new upcast ventilation shaft midway between No. 2 Shaft and No. 3 Shaft.The shaft is finished to 16 ft. internal diameter and connects with the mine workings at the 2,600-ft. level. It is lined with unreinforced Concrete approximately 12 in. thick. The shaft sinking routine was drilling, blasting and mucking by hand using a 27-cub. ft. capacity bucket. The concrete lining was poured in conjunction with the sinking and was normally finished within 30 to 50 ft. of the shaft bottom.

Jan 1, 1957

By Sowerby BD

The CSIRU Division of Mineral Engineering is developing various techniques for the on-line determination of moisture in coal and coke, and some instruments are now commercially available. These techniques permit accurate and rapid determination of moisture in materials directly on conveyor belts or in bins. The most promising techniques for direct on-belt measurement of moisture in coal are capacitance and microwave transmission. A non-contacting under-belt capacitance and gamma-ray backscatter technique has determined moisture in coal to better than 0.5 wt'/. in field tests at BHP Stockton Borehole Colliery, NSW. Mineral Control Instrumentation Pty Ltd have been licensed to manufacture the capacitance gauges and have installed five commercial units in the coal industry and other industries. Microwave transmission techniques have an advantage over the under-belt capacitance technique in that they are not sensitive to vertical segregation of moisture in coal on the conveyor belt. A laboratory prototype of a microwave transmission gauge has been constructed and tested. Microwave techniques, based on a measurement of attenuation and phase shift, are under development and are expected to be field tested in 1987. These new techniques will enable a wide range of thickness changes to be accommodated. Capacitance and microwave transmission methods are unsuitable for materials of high electrical conductivity, such as coke. CSIRO is therefore developing a fast neutron and gamma-ray transmission technique, which is proving very accurate in laboratory tests. This technique overcomes many of the limitations of thermal neutron moisture gauges and it is expected to be field tested in 1987.

Jan 1, 1987

By Das S. C

A detailed study was undertaken on the effect of Fe+3 in combination with LIX64N during copper electrowinning from sulphate electrolytes. The results show that the presence of Fe+3 not only affects the current efficiency during copper electrowinning but also affects the cathode quality. The effect is enhanced by electrolysis parameters like temperature, circulation rate, current density, etc. No significant effect was found from the presence of Fe+2. The presence of Fe+3 along with LIX64N causes a synergistic effect and results in a drastic fall in current efficiency. Moreover, cathode quality is also affected. A pyramidal structure is favoured in the presence of Fe+3 but the presence of LIX64N along with Fe+3 promotes a ridge structure. Addition of thiourea not only causes modification of cathode deposits, but also a rise in current Efficiency.

Jan 1, 1992