Search Documents

Recent and on-going studies on the leaching of gold, the properties and activity of carbon, developments in the elution of gold from carbon, and methods of recovering gold from solution are reviewed. Emphasis is placed on Australian contributions, and their impact on gold metallurgy. Consideration is given to the future development of selective solvent extractants, ion exchange resins or alternative reagents for cyanide.

Jan 1, 1987

By Crosby N. R

The design of mine openings and the assessment of their reserve are processes ihicl, require the routine manipulation of considerable amounts of data. A number of computer programs have been assembled to operate in a mini computer in order to provide some mechanical assistance for these processes. The system responds to plain language commands. which allows mining engineers to compute the reserves for a number of possible mining outlines, on an interactive basis. Methods of numerical analysis were used in preference to statistical or qeostatistical techniques.

Jan 1, 1977

By Niemann G

The paper addresses certain mining provisions of the Aboriginal Land Rights (Northern Territory) Act 1976 and the development of Mining agreements negotiated pursuant to Section 43 of the Act. Difficulties for miners and Land Councils alike arising out of the operation of the Land Rights Act will be discussed. Possible scenarios for the resolution of these difficulties will be proposed.

Jan 1, 1984

Excavation through fill material in underground metalliferous mines is usually avoided where possible, unlike in Civil Engineering application where excavation through soft ground is normally a matter of course. In the mining situation, where excavation is normally for access only, then excavation designs are engineered for mining in hard rock, except where previous lack of forward planning has made such excavation inevitable or a mining strategy sequence necessitates some mining through fill in order to achieve optimum recovery of ore. Historically, this has been the case, because of the lack of knowledge of the support characteristics of the fill material placed underground and the lack of knowledge of the composition of the fill material as placed. The expertise and experience available from mechanised excavation techniques in Civil Engineering application (shield jacking, forepoling, spiling, and soft tunnel boring, to name a few) are available for application to the underground mining situation if the need ever arises. This paper describes the situations in underground mining development where mining through fill material is required, the different types of fill material encountered and the types of support available

Jan 1, 1981

ABSTRACT' The first references to gold in New Guinea were by the Portuguese in 1525. The first significant discovery and gold rush was on Sudest Island in 1888 and was a natural extension of the rush that surged up Australia's eastern coast and ended at cook- town. Prospectors made a series of minor discoveries in coastal regions before the first large discovery at Wau/Edie Creek/Bulolo in 1925. Major post war gold discoveries were made at Bougainville, Frieda River, Porgera and Ok Tedi. On Misima Island a large bulk low grade deposit has been recognised surrounding old gold workings. Gold exploration has increased drama- tically since the lifting of a 3 year moritorium on new exploration areas in Noverrber 1982. A new bulk low grade gold discovery has been made on Lihir Island, north of Bougainville and a number of other promising areas are being drilled. Gold production is also expanding dramatically from current levels of 600,000 ounces to an anticipated 1.3 million ounces in 1985 with the opening of Ok Tedi. Other potential developments are likely to increase output above 2 million ounces by 1990. Papua New Guinea's world ranking as a producer is likely to move from 9th to 7th in 1985 reflecting the favourable geological potential, stable political environment and attractive development terms offered by the Government.

Jan 1, 1984

By M Behrens, A McPhee, B D. Hegan

This paper describes the design and construction of twin 400 m long road tunnels as part of the Northern Motorway Extension Project in Auckland, New Zealand. Construction of the tunnel civil works is now completed and installation of mechanical and electrical systems is well underway. The tunnels are expected to be open for traffic at the end of 2008. The paper will address the design aspects of the project including: tunnel alignment and cross-section, geotechnical conditions and rock support, waterproofing and concrete lining and fire and life safety. The paper will cover the bored tunnel section, the cut-and-cover tunnel section, cross passages and portal structures. The design brief included a requirement for the tunnels to be a gateway to Auckland and this required particular attention to be given to the visual appearance of the finished tunnel structure. The final arrangement of the portal structures and a requirement for recesses in the concrete lining for emergency cabinets, deluge pipework and cable runs, reflects these requirements. The tunnels were excavated by a roadheader and road planer using a heading and bench. Initial support was provided by a combination of lattice girders, cement grouted rock bolts and steel fibre reinforced shotcrete. The permanent lining consisted of installation of a drainage geotextile and waterproof membrane, followed by cast in situ unreinforced concrete. Each portal consists of a cut-and-cover section. This paper describes the tunnel construction methods, including the particular requirements for safety, the environment and community relations. The tunnel is fitted with a compartmentalised deluge system for fire fighting purposes. The tunnel control centre is incorporated into the control centre for Auckland Harbour Bridge, some 30 km from the tunnel location.

Jan 1, 2008

By T Weldon

In the last 15 years, it has become increasingly popular to win gold and silver from carbon strip solutions with electrolytic æsludgeÆ cells. The precious metal sludges produced in the cells are washed to the cell bottom and pumped into filters. Most new operations are specifying sludging cells, and many older operations are being retrofitted with up-to-date electrolytic sludge cells and filters. The new sludging cells are generally more energy efficient than older cells, but more importantly, the cell operations to remove product are much less labour intensive, cleaner, and the operator need not have physical contact with the electrolytically produced metal. A case study of a major North American gold producer (50 000 kg/yr) that removed old style stainless steel wool cathode cells and installed new sludging cells and sludge filters is presented. The effect of various impurities is discussed.

Jan 1, 2005

By Diessel C. F K, Ng N

The commonly used Stopes-Heerlen coal petrographic classification and nomenclature has over the years been subject to variable interpretations. This paper discusses the problem with specific reference to the inertinite maceral group. The effect of various interpretations of the Stopes-Heerlen system on maceral analysis is discussed and illustrated by means of comparative analyses conducted by a number of laboratories in Australia. An attempt is made to define the reflectance thresholds used by the authors to subdivide the inertinite group; the genetic and technological significance of these thresholds are compared. The difficulties of distinguishing structured and non-structured macerals of the inertinite group is discussed in terms of possible improvements to the present Stopes-Heerlen system by extending the classification to include transitional maceral types.

Jan 1, 1969

By Dobos SK

The Black Ridge Gold Deposit is located in the northern part of the Clermont Goldfield, which is situated at the boundary of the Bowen Basin and Anakie Inlier, Queensland. The goldfield comprises a series of NNW-trending semi-isolated basins, which are tectonically aligned with the Denison Trough, the west-most division of the Bowen Basin (Fig. 1-1).The main stratigraphic units in the deposits in younging sequence are the Anakie Metamorphics, the early Permian Blair Athol Coal Measures, the late Permian(?) White Section, and the Tertiary basalts which are regionally widespread, and intruded by abundant mafic and felsic plugs.

Jan 1, 1990

By Bailey S, Avraamides J

Laboratory-scale experiments were conducted in a mechanically stirred aeration vessel to determine the rusting abilities of aerated water in the presence of various catalysts compared to the industrially used ammonium chloride. The catalysts used were tartaric acid and citric acid, firstly by themselves, and then in later experiments mixed with ammonium chloride. From these experiments it was found that leaching of iron from reduced ilmenite in the presence of either tartaric acid or its sodium salt was much slower than in the presence of ammonium chloride. Citric acid or its sodium salt also give a slower rate of leaching than the ammonium chloride system, but citric acid and its sodium salt mixed in equal proportions produced a rate of leaching approximately twice as fast as the standard ammonium chloride system. When tartaric acid was mixed with ammonium chloride the leaching rate was found to be equivalent to the leaching rate of the same amount of ammonium chloride alone, thus indicating that tartaric acid made no contribution to the leaching in this svstem_

Jan 1, 1996

The effect of accurate detonator delay timing on blast results can now be studied with the development of the ICI Electronic Detonator. This detonator has an accuracy and precision orders of magnitude greater than the current range of pyrotechnic delay detonators. A series of field trials have been conducted to quantify the effect of delay accuracy and timing on blast performance. These trials have demon- strated that delay timing can have a marked influence on blast fragmen- tation, muckpile displacement, blast vibration and airblast.

Jan 1, 1989

As part of its Concentrator operation Hamersley Iron Pty. Limited uses wet high intensity magnetic separation to upgrade shaley low grade ore in the minus 0.5mm size range. Materials handling problems, largely caused by fine ore types and design deficiencies, surfaced in the Fines Treatment Plant soon after Concentrator commissioning in 1979. Surging throughout the circuit impaired process efficiency and added to problems caused by capacity and process control limitations. In 1981 extensive modification works were initiated to supplement minor changes made to that date. The new circuit significantly increases capacity and provides greater process control.

Jan 1, 1978

By D Sidea

There has been increased focus in Australia on large diameter raise boring for ventilation shafts and orepass excavation in good quality, brittle, highly stressed rock. As mining in many parts of Australia progresses to deeper levels, more vertical openings are being excavated in highly stressed ground conditions. However, whilst shafts have been successfully raise bored in highly stressed rock, it is often at a significantly increased risk of loss or damage to inhole equipment. It is important for both mine owners and contractors to have an appreciation of these risks at the planning and tendering phases of raise boring contracts. This paper provides an understanding of the risks associated with large diameter raise boring and a review of methods to predict failure in highly stressed rock.

Jan 1, 2005

The Favona Underground Project is located approximately two kilometres east of Martha Mine Open Pit in Waihi, 150 km south east of Auckland, New Zealand.   The underground reserve of 354 koz Au contained in resources of almost 600 koz lies within 600 m of the existing process plant presenting an attractive development target in a challenging environment.   The Martha Mine Open Pit is surrounded by urban housing on the north western edge of Waihi township and the Favona Underground abuts residences on the eastern edge of town. Environmental, community and social licence aspects influence project strategies as the new underground mine extends mining in a town that is planning for closure of current open pit operations in late 2006.   The Favona Underground Project has successfully passed through a detailed feasibility study, the third stage of the five stage Newmont project appraisal system. Methodologies used in the feasibility study and parallel permitting draw on a high level of stakeholder involvement to streamline the development and permitting phases.   This paper discusses the project appraisal process and design innovation required for developing an underground mine adjacent to town.

Jan 1, 2004

By Anderson K

In 1991, the first horizontal raise drill hole in Australia was successfully completed by Australian Raise Drilling Pty Ltd (ARD) at the Perseverance nickel mine of Western Mining Corporation's (WMC's) Leinster Nickel Operations in Western Australia. At that time, WMC were experiencing considerable difficulties in developing the horizontal drill drives through the orebody using conventional drill and blast techniques. Following the success of the initial hole, a further two holes were drilled as part of the evaluation program. The technique has proved so successful that it has been accepted by WMC for on-going development of drill drives at Perseverance.This paper describes the program. It relates how the project evolved, the modifications that were required to the equipment used, the performance experienced during the program and the future of the method in this and other applications.

Jan 1, 1993

By Klinefelter G

The United States Steel Mining Co., Inc. recently experienced a major mine fire at the Cumberland Mine. This mine is located in Greene County, Pennsylvania, U.S.A. and is mining a high volatile bituminous coal seam (Pittsburgh Seam). The mine fire was success- fully controlled and extinguished without loss of life or serious injury to any miner or mine rescue personnel and finally reopened within 40 days of its inception.

Jan 1, 1988

By J Arif, J Proffett

Copper and gold mineralisation at Batu Hijau is directly related to quartz veining and wall rock alteration that developed in close spatial and temporal association with multiple tonalite porphyry intrusions. To its advantage with respect to the study and better understanding of the evolution of the porphyry system, Batu Hijau has comparatively minor late alteration and mineralisation overprints. This paper summarises results of detailed geological logging, petrographic studies and geochemical analyses of diamond drill cores from the deeper sections of the Batu Hijau porphyry system (ie its roots). An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

A sample of fifty fractured low chromium-molybdenum alloy drill steel rods was investigated. Each rod was of the forged collar integral tungsten carbide type in common use in Australia.Examination of a new rod of the same type showed that a zone of spheroidized carbide about 0·25 in. wide was present about 12 in. from the shank end.Examination of the fractured rods revealed that 78 per cent. of failures occurred within 0·25 in. of the spheroidized zone at the shank end but in the main stem of the rod rather than actually in this softened zone where it might be expected to occur.This predominant type of failure at the shank end in the steel rods is caused by a highly anodic region corresponding to the first stages of spheroidization of carbides present in the steel. Accelerated corrosion in the narrow band havil\g this structure induces the formation of stress-concentrating corrosion pits, 78 per cent. of failures in this region being due to corrosion fatigue.The remaining 22 per cent. of failures, occurring in the as-rolled stem, were due to either corrosion fatiglie if failure were initiated at the water-hole surface of the drill rod, or to a decarburized outer surface if failure originated at this surface.Temperatures producing spheroidization were determined as 6007600C.Evidence suggests that approximately 75 per cent, of shank-end failures in all forged collar drill rods can be attributed to corrosion fatigue occurring preferentially in that section showing partial spheroidization of carbides· produced by the forging and hardeningoperations.Methods are suggested for reducing the frequency of fatigue failures in drill rods.INTRODUCTIONAn integral part of all tunnelling operations through rock is the drilling of suitably placed holes i:n.to which explosive is subsequently rammed and exploded.The drilling operation, whether for metalliferous mining or for general civil engineering constructional work; is...

Jan 1, 1955

The invitation to speak today was in the form of a single sentence instruction: How does your company run and how do you communicate from top to bottom? It looks like I'll have to let you into our little secret. The team at Croesus know what works for us but we've never talked about it with others - least of all presented it at a conference such as this. In fact we tend to avoid the jargon normally associated with Best Practice or TQM, however in our own way, each of our staff are 100 per cent loyal to our company's aim to maintain and strengthen our commercial success. Just how we achieve this at Croesus is the subject of this presentation today, but first a little history. My dear old grandfather arrived in Kalgoorlie, as a mining engineer 100 years ago. Do you think he would have chuckled if someone suggested to him that a hundred years later we would just be starting to understand Kalgoorlie's geological mysteries? Well, here we are 100 years later and Croesus Mining is fortunate to be part of a generation now realising the true potential of Kalgoorlie's Goldfields. This provides us with a very fertile field in which to sow the seeds we can obtain from the World's Best Practice in Mining and Processing. With each new mineral deposit being discovered, old theories are being exploded. Each new deposit has a personality of its own, leading to some belated pioneering theories of where to drill next, and how to reduce internal costs so that we can win the war against constantly increasing external costs. What we have now and what the old timers didn't have is a huge database of geological input spanning several gold booms and a couple of nickel booms. My only interest in history is to pick up the points that may help us for our future. This is what we are doing in our company which is something of a David, in the David to Goliath range of mining companies in Australia. As a humbling thought; of the 115 164 tonnes of gold that the world's mines have produced throughout history, four tonnes have been produced by Croesus Mining. That's equivalent to 0.003 per cent of the total world's gold production. In the past financial year we achieved a dividend yield of five per cent. To put this into perspective, that's over twice the dividend yield of BHP, Australia's largest company. As we are somewhat less known than BHP, let me spend a few moments giving some particulars of our company's background.

Jan 1, 1995

The refractory industry in New Zealand is small, consisting of two main manufacturers - one at Huntly and the other at Kamo. Together these would have an annual refractory production of about 30 000 tonnes. The industries which use refractories include two steelworks, NewZealand Steel Limited and Pacific Steel Limited, the former is involved in continuous casting from sponge, iron and scrap steel and the latter is involved in ingot teaming from scrap steel and steel billets; One aluminium smelter, cement works, dairy companies, small foundries producing engineering requirements and many other small users. The New Zealand manufacturers produce refractories in thefire brick range, that is up to 50 per cent alumina content (ignited basis), based on indigenous raw materials and in the high alumina range up to 85 per cent alumina content (ignited basis) based on imported bauxites. All of the basic refractories high purity silica and high alumina low alkali refractories and many of the higher grade acid resisting refractories are imported.

Jan 1, 1976