Search Documents

By M I. Pownceby, M A. Rhamdhani, S Purohit, G Brooks

The current practice of magnetite ore agglomeration involves high temperature oxidation roasting (typically at 1200–1350°C) of magnetite to hematite phase in order to improve the strength and reducibility of pellets. The requirement to pre-oxidise the magnetite before introduction to an ironmaking plant increases the CO2 emissions generated during the ironmaking process. In our previous papers, a novel, alternative agglomeration route for magnetite ores was presented where magnetite was converted to a reducible CaFe3O5 (CWF) phase through the addition of lime to produce a Lime-Magnetite Pellet (LMP) feedstock that can be directly charged to ironmaking units. The LMP process eliminates the magnetite oxidation stage, thereby reducing the CO2 emission during ironmaking. The concept was tested by thermodynamic calculations, high temperature experiments and scaled-down pilot scale test work. In this paper, larger scale synthesis of halfstoichiometric LMPs (1 mole of Fe3O4 and ½ mole of CaCO3) were prepared using a balling drum, followed by overnight drying at 110°C and induration at 1050°C for two hours. The LMPs were analysed using X-Ray Diffraction and Scanning Electron Microscope techniques for phase and microstructure characterisation. The LMPs were found to have 14–15 wt. per cent of CWF phase when indurated under a CO2/CO ratio of 8.5:1. Pilot scale testing of the LMPs was conducted following ISO standard test procedures. The test results indicated the LMP’s had a Reducibility Index (RI) of over 91 per cent, a Tumbler Index (TI) of 87 per cent and a Reduction Degradation Index (RDI) of 4.6 per cent. The results indicate LMPs may be useful as an alternative feedstock to ironmaking processes that would result in lower overall CO2 emissions.

Nov 8, 2021

By F Ouchterlony

Soviet precursors to Cunningham’s Kuz-Ram model from 1983 are described. They are rooted in the mean fragment size and Rosin-Rammler (RR) fits to sieving data and rely on approximations. Three versions of the Kuz-Ram model are presented and all three are de facto based on the median fragment size x50, even if the term mean is used in the papers. This discrepancy caused Spathis in 2004 to suggest a correction procedure for the Kuz-Ram rock factor A, which was said to explain some of the missing fines in the model. This correction, while applicable to Cunningham’s 1983 paper, does not apply to his 1987 paper, in which he presents his own A factor.Common fixes of the Kuz-Ram model’s fines issue are fragmentation models where the fines are mainly generated in a crushed zone around a blasthole. This is contradicted by careful model blasting tests. The lack of a largest block size in the RR function may lead to spurious values of the uniformity coefficient n, eg in conjunction with image-based fragmentation measurements or crusher modelling. These issues may be solved by using the transformed RR function, which has a largest block size xmax or its replacement by the Swebrec function, such as in the KCO model.The mean to median issue is investigated in some detail and it is found that using x50 instead of the mean:has a sounder theoretical backgroundis less prone to errorsis not contradicted by the original Soviet data.It is finally suggested that future work on fragmentation prediction equations focus on the use of distribution independent quantities like percentiles, eg x50, x20 and x80. Some previous work in this direction is briefly analysed and one consequence is that the n-value of the Kuz-Ram model should depend on specific charge.CITATION:Ouchterlony, F, 2015. The median versus the mean fragment size and other issues with the Kuz-Ram model, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 109–120 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

Silver-lead mineralization at Indooroopilly, Queensland, extends upwards from Upper Triassic rhyolite which intrudes phyllite-containing Palaeozoic mineralization.Sulphides and magma were emplaced in a special structural site which underwent dilational fracturing while surrounding rocks were block-faulted and compressed. This site lies at tbe intersection of dykes, faults, and a lineament adjacent to a Middle Triassic granitic stock.Structural controls at Indooroopilly are attributed to the effects of piston faulting. Exploration for similarly controlled deposits should be directed towards structural intersections near stocks or batholiths which have intruded mineralized belts. Priority should be given to structural intersections which were sites of block-faulting and igneous activity under compressional tectonic conditions.Favourable sites lacking surface mineralization may contain ore at depth as piston faulting produces 'blind' ore deposits.

Jan 1, 1976

By Cook B, Cunningham J

At Mount Isa Mines, a system has been developed for general monitoring of underground mobile equipment. It can provide unit condition monitoring data such as oil pressures and motor temperatures as well as production type information such as unit location and load. The system does not rely on an expensive data communications infrastructure, using instead inexpensive radio base stations which automatically transfer data from mobile units to a surface database server on the company-wide computer network. This paper includes a general overview of the system and a discussion of the practical benefits it is expected to generate.

Jan 1, 1995

By Johnson MT

The microprocessor revolution of the 1970's dramatically improved the price/per- formance of graphics hardware. Together with improved communications and new software concepts and standards this has resulted in the emergence of a new tool with particular application to the mining industry. The Distributed Graphics Processor (DGP) offers more natural means of interaction with com- plex technical models.

Jan 1, 1983

By S Bandopadhyay

The seasonal fluctuations of the dust content in Arctic mine environments and the environmental variables affecting the intensity of dust production are qualitatively well known, but quantitative models that allow simulation and prediction of dust generation and the effects of engineering control of thermal regime on the mine environment are still non-existent. In Arctic mines, the migration of moisture in the surrounding rock mass releases fine dust by freeing it from the ice matrix allowing it to escape into mine airway. The migration of moisture is the direct cause for the production of mine dust and heat is the primary driving force. This paper examins the heat and moisture exchange between the ventilation air and the surrounding rock mass in frozen ground, placer mines in the Arctic. Based on the simulated results of a coupled heat and mass transfer problem with phase change, methods of dust control have been identified for mines in the Arctic.

Jan 1, 2005

By Stille H

The choice between drill and blast and mechanical boring methods is often not obvious. There are several factors which may have a de- cisive influence on this choice, such as the geometry and length of the tunnel, site con- ditions and borability of the rock. Both the un- confined compression strength and the joint dis- tance have a considerable influence on the net penetration rate. Site conditions, rock quality and water conditions influence the utilization of the tunnel boring machine. The drill and blast method is normally less sensitive to devi- ations from assumed ground conditions.

Jan 1, 1987

 Increasing concern about the impact of alluvial mining discharges on the water quality of some West Coast rivers lead to a joint West Coast Gold Miners Associate, Trade and Industry funded study by Water Technology (NZ) Ltd. The objective of the study was to assess the treatability of West Coast alluvial gold mining discharges and to develop simple treatment systems which could be effectively adapted to a variety of sites in the region.   The approach was to apply standard water treatment techniques to field situations using low cost technology. Initially the various types of alluvial gold mining operations were identified then after preliminary site investigations and laboratory studies were carried out, site pilot plants were set up. The results of the trials particularly those using chemical aids were encouraging and it was found that chemical aid performance was largely dependent on the degree of mixing at and downstream of the chemical addition point. Design alterations to settling pond configurations in conjunction with optimised chemical addition yielded dramatic results in the form of reduced effluent turbidities.   A generalised approach to effluent treatment was developed and some of the specific 'mix and match' requirements were identified for different types of sites. The general conclusion is that improved physical treatment combined with good plant management and operation and (where necessary) chemical treatment, will produce water of acceptable discharge quality.

Jan 1, 1989

Most internationally traded iron ore resources are derived from multiple mine sites, transported to a port facility where they are blended and possibly further processed prior to shipping. Provided the proportion of contributions varies over a number of shipments an estimate can be made of the bias introduced by mine site sampling, analysis and materials handling systems, using zero-intercept multiple linear regression. Further regression applied to the residuals allows the error variances for the source mines to be estimated. Various sampling strategies are used by the industry. All have shipment-loading sampling on which payment or at least provisional payment is based. In most cases sampling prestockpile is used at mine sites to verify estimated production grades. Train grades are estimated from mine stockpile grades and in some cases train grades are verified by port input sampling. The methodology used is presented in this paper. Simulated data have been used and do not reflect the actual performance of any operator. The merits of the various systems and the implementation and potential limitations of our method are discussed more fully in a companion paper (Ziegelaar and Everett, 2010).

Mar 1, 2010

By J Col, D La Rosa, W Valery, A Jankovic

Metso Minerals Process Technology Asia-Pacific and South America (MMPT) has been working with operations around the world to increase their efficiency through æMine-to-MillÆ or Process Integration and Optimisation (PIO) projects. These projects have delivered significant improvements in mine efficiency, mill throughput and reduced operating costs at mines around the world. The MMPT methodology involves rock characterisation, site auditing, data collection, modelling/simulation and implementation of integrated operating and control strategies on site. This results in significant benefits to the operations û for example, 5 to 20 per cent increases in concentrator throughput have been measured. MMPTÆs rock characterisation utilises simple and inexpensive measurements that can be performed by trained site personnel. The advantage of these measurements is that a large amount of data can be collected in a very short timeframe, as the samples do not require shipping to an outside laboratory. Typically, a PIO project starts with a site visit to perform blasting and process audits, collect high quality data including measurements of run-of-mine fragmentation and survey data around all crushing and grinding circuits. These measurements are combined with rock characterisation and the definition of strength and structure domains to model the complete production chain. Site-specific models of the blast fragmentation, crushing, grinding and flotation processes can then be developed. This proven methodology has applications ranging from greenfield projects to long-standing operations with AG/SAG or conventional grinding circuits. Process improvements can be higher mining productivity, higher mill throughput, decreased overall operating costs and higher flotation or leach recovery. This paper discusses a recent application of PIO conducted at a large open pit operation in South America and emphasises the potential that every operation has to ædo more with what they haveÆ.

Jan 1, 2007

By G J. Butler

Since 2005 BHP Billiton Iron Ore has been working with the consulting company Runge to implement the software XPAC Advanced Destination Scheduler (ADS) in life-of-mine studies. The Mt Whaleback mine, being the single biggest open cut iron ore mine in the world, presents some special challenges in scheduling. The biggest challenge has been the slow run time and difficulty in targeting all ore and waste requirements. The high waste to ore strip ratio means that much of the cost of mining is tied up in waste dumping. It is therefore very important to schedule waste efficiently. At Mt Whaleback there is an additional challenge of managing two types of waste: inert and environmentally sensitive pyritic material. This paper shows how the XPAC destination scheduler is configured to achieve efficient and repeatable waste scheduling results at the Mt Whaleback mine. It also discusses proposed improvements to the process. The overall ore and waste schedule is configured to target mining parameters, crusher feed and grades. The schedule is run in two stages. The first stage is ore mining. The waste that needs to be mined is locked in a sequence. The second stage is the waste scheduling. The waste destination scheduler uses three inputs: source waste parcels locked in a sequence, a haul road and a waste dump block model. The process involves setting some rules for dump progression and haul path selection. These can be validated. The schedule is then run to target the shortest travel time. The results of scheduling are graphical and numeric and can be transferred into many different formats for reporting. The graphical result shows face positions in time that can be used for detailed dump design. The numeric results are used to estimate truck fleet size, fuel consumption, labour and equipment financials. The process has been successful in reducing the project time line, increasing the ability to do more scenarios and increasing schedule accuracy, transferability and repeatability.

Jan 1, 2007

Transport Canada (Federal Government) constructed the Halifax International Airport (HIA) near Halifax, Nova Scotia, Canada in the late-1950s. Site location criteria were primarily; direct access to the city and a raised flat topography. Unfortunately, the site chosen was located on shallow Meguma group pyritic slate bedrock. In 1982, during the construction of an airport taxiway, it became very apparent that acidic run-off from excavated bedrock at the site was having a negative impact on adjacent aquatic habitat. The ensuing 20 years involved many efforts to rectify the acidic drainage problem with mixed results. Some of the techniques which have been implemented at HIA to address the acid rock drainage (ARD) issue include: dry covers, wet covers, wetlands, electrochemical treatment, open limestone channels, limestone gravel polishing beds, agricultural limestone application, and two hydrated lime [Ca(OH)2] addition treatment plants, the first producing low density sludge and the new one that creates high-density sludge. Based on over 20 years of water quality monitoring data it is apparent that only certain acid drainage mitigation methods have been effective at HIA. In 2000 when the Halifax International Airport Authority (the Authority) took control of the operation and management of the airport, including the ARD issue, it was decided to construct a modern, highdensity sludge, hydrated lime treatment system. This new $CAN 7 million system is now in operation and is achieving compliance with water quality guidelines. Due to high operating cost, a review of methods to optimise the system is being carried out. The HIA ARD problem, though minor by comparison to most mine sites, has provided unique challenges and may provide valuable insights into this urgent environmental and financial issue.

Jan 1, 2003

By T R. Justice

The Eastern Distributor tunnel is located approximately 24 m beneath the suburbs of Woolloomooloo and Darlinghurst to the east of the central business district of Sydney. The 1.7 km long tunnel will carry three lanes of northbound traffic over three lanes of southbound traffic in a æpiggybackÆ arrangement, with a maximum cross-section 22 m wide by 12 m high.The tunnel is constructed predominantly within horizontally bedded Hawkesbury Sandstone. In the unweathered to slightly weathered state, the rock is typically medium strength (average UCS about 24 MPa), with an average quartz content of 72 per cent.Major geological features that intercept the tunnel route are the Woolloomooloo Fault Zone and two extremely to moderately weathered dolerite dykes. The fault zone intersects the tunnel at about 25¦ to its alignment and comprises a series of discrete faults over a width of approximately 50 m. The overall movement of the fault zone appears to be reverse. The two dykes are the 1 m wide Oxford St Dyke and the 6 m wide Great Sydney Dyke.This paper outlines the site investigations and the interpreted geotechnical model for the tunnel route prior to the commencement of tunnelling. This model is then compared to the encountered conditions. The very good correlation between the expected and the encountered conditions shows the high quality of geotechnical investigation and interpretation.

Jan 1, 1999

This paper introduces a classification of gold orebodies, and comments on the importance of cutting high grade values, the choice of an appropriate ore reserve method and the necessity for producing recoverable ore reserves by considering the mining policy. The author stresses the importance of obtaining the appropriate information from the data relevant to a particular deposit as opposed to transfering parameters from one deposit to another.

Jan 1, 1987

By Minchinton A

CPeX is a non-ideal explosive performance prediction model. The model takes into account the rate of energy release, the extent of chemical reac- tion and the effect of confinement on energy release. The model resolves the explosive energy into `shock' and `heave' com- ponents as a function of explosive type, hole diameter and rock type. The predictions of the model are compared for a bulk emulsion, and a prill-doped bulk emulsion in soft rock. The predictions, based on calibra- tion of the model with simple unconfined detonation velocity measure- ments, show the significant effect of non-ideality on explosive Performance.

Jan 1, 1988

By Samyguin VD, Filippov LO

The aim of this paper is to emphasise the importance of knowing of the rate of the elementary flotation acts (EFA) - attachment and detachment. By studying the simplest linear model notion of the column flotation, the results of the nonlinear simulaton of flotation separation in the column with lengthwise upward mixing show two principal different types of separative mass-transfer in the column. The first is, the case of a small EFA intensity, almost without the detachment. The second is, the case of a big EFA rate, when the process is close to a local attachment-detachment equilibrium. There is also an attempt to estimate the EFA rate for three different kinds of quartz particles, floated by cation collector in the laboratory column apparatus.

Jan 1, 1993

By I Govender, T L. Moodley

Tumbling mills are grossly inefficient, using only 5 per cent of the total energy supplied for actual breakage. A significant proportion of this inefficiency is unavoidable owing to geometric limitations; rotating drum systems are prone to exhibiting certain regions (energy barriers) that resist particle entry thereby restricting the transfer of energy. Though such systems are inherently inefficient, improved modelling schemes may lead to slightly enhanced efficiency through better microscale predictions of key breakage drivers (stress, force). Central to achieving such incremental advances is the development of a universally accepted rheology for dense granular flows. Armed with a better understanding of these macro-scale ingredients, classical process modelling offers an efficient, spreadsheet friendly framework for recovering the spatial distributions of the comminution drivers. At this real-time level of process control, it should be possible to tune comminution operations towards more energy efficient configurations – the ultimate goal of this research. The present work employs validated DEM data to recover the full continuum field which will ultimately serve as a basis for calibrating process model outputs based on different rheological hypotheses. Such a continuumbased approach captures tensor properties like the shear stress and strain rate – both of which are necessary to developing a dense granular rheology. Moreover, DEM captures this data at the momentum transfer timescale of 10-6 s – no other measurement technique is capable of this level of spatial and temporal resolution. Importantly, the confidence in this DEM data is strengthened because it has been validated at the continuum scale using Positron Emission Particle Tracking (PEPT) kinematic measurements. Validated DEM data is derived from batch experiments conducted within a 300 mm ID laboratory drum using three and five millimetre glass beads at 60 and 75 percent critical speed; such mill speeds are typically encountered in the tumbling mill industry. Dimensional analysis is conducted using critical rheological parameters (shear rate, shear stress, granular temperature etc), which are key to not only developing a granular rheology but ultimately will be used to tune our mechanistic models.

Aug 24, 2022

The New South Wales Department of Mineral Resources has, since 1974, administered the Derelict Mines Rehabilitation Program (DMRP) to reduce the environmental impacts of abandoned and orphan mine sites. The application of the DMRP is presented in case studies of sites from the South Maitland Coalfield featuring residual drainage of acidic and saline water in a semi urban and rural community setting. The acidity here is typically derived from iron oxidation in shallow underground coal mine workings and in surface emplacements of coal washery reject materials. This paper presents summary information on AMD investigation, monitoring and rehabilitation. The experiences of community expectation, stakeholder consultation and peer review are discussed.

Jan 1, 2003

By M E. Malmstr÷m

Quantification of site-specific sulfide oxidation rates is crucial to accuracy of prediction of, for example, the environmental impact of a mine site. Sulfide oxidation reactions are reportedly increased by bacterial mediation; determination of abiotic and biotic weathering rates thus requires the establishment of sterile control samples. However, sterilisation often involves exposure of samples to extreme conditions that may alter the physical, chemical, or mineralogical characteristics of the tailings and hence affect element release rates. The impact of various sterilisation techniques, common and novel, on the element release rates from tailings from the Kristineberg site, northern Sweden, has been investigated. Batch weathering experiments indicated that the different methods of sterilisation (autoclaving, heat treatment, ethanol/heat treatment, application of antibiotics, rinsing with distilled water, and γ-radiation) did not greatly affect long-term element release rates. Long-term experiments (>30 days) are thus to be recommended for establishment of weathering rates. Sterilised and untreated control samples showed similar element release rates after ~100 days of experiments; possible explanations include that microbial oxidation is not important under our experimental conditions (Po2 = 0.2 atm, pH ~2.3, 22¦C, 0.01 M HNO3, no additional nutrients).

Jan 1, 2003

The U.S. Bureau of Mines has developed a prototype cross well acoustic logging system and complementary tomogr`aphic image reconstruction software for the detection and delineation of abandoned underground mines and associated subsidence failure in relatively shallow environments. The logging system uses a piezoelectric, cylindrical bender as an acoustic source. A triaxial accelerometer assembly, designed to be rigidly locked in the borehole, is the receiver portion of the logging system. Both the source and receiver probes operate at high frequencies, thus providing short wavelengths capable of resolving small features in most rock types. A modified van with a dual-drum wireline winch, 4-channel data acquisition system, power amplifiers, and waveform generator supports field operation of the logging system. A field study was conducted at a test site in San Antonio, Texas, to demonstrate the cross well acoustic logging system. The underlying rock at the test site is similar to stratified sediments in coal measures. First- arrival travel times were interpreted by tomographic reconstruction of the velocity field in the two-dimensional cross section between the source and receiver boreholes. The resulting image correlates well with geological borehole logging data for the test site.

Jan 1, 1992