Search Documents

Australia contains a variety of iron ores, differing in grade, chemistry, size distribution and genesis. While a proportion of this ore is used world-wide as blast furnace lump, much of the material mined is high grade fines, requiring agglomeration (usually sintering) before blast furnace reduction. Sintering studies initially concentrated on the production of ferrous material of high iron content, coarse size and sufficient cold strength. In recent years research involving pilot plant sintering, precise test procedures and mineralogical analyses has focussed on the additional sinter properties of hot strength and reducibility. Aspects of mineralogical studies applied to iron ore sintering are described.

Jan 1, 1989

By Krokhmai VS, Sayko OP

The paper summarises the theoretical and experimental studies which led to the development of new industrial equipment designed to recover liberated gold from placer gravity concentrates. The new technology is based on environmentally clean magnetic methods, which avoids use of mercury in the production process and obtains higher gold recoveries compared to the amalgamation technique, and which can reach 98.6 - 99.5 per cent. The complex of equipment thus developed is now commercially used at nine Russian gold mining operations. Six more such complexes are due to come on stream in 1993, some of them outside the CIS. The new technology appears to hold much promise for the recovery of precious stones (diamonds, rubies etc) semi-precious stones (pyropes, chrysolites etc) and also artificial diamonds, for which case there are encouraging laboratory results.

Jan 1, 1993

By W A. Peppin, D N. Riley, N W. Schulenburg

In June 2008, a joint airborne collection using hyperpspectral systems was tested on a single Twin Otter aircraft. This experiment was designed to incorporate two airborne hyperspectral sensors for geological and environmental projects. Mineral exploration and environmental impact statements are two areas where full spectrum hyperspectral data can document the mineralogy at the surface prior to mining operations. Many previous hyperspectral remote sensing collections were collected on a single aircraft with a single sensor. Mineral mapping using hyperspectral sensors that measure in complimentary regions of the electromagnetic spectrum is cost effective as it allows for the mapping of clays, sulfates, carbonates, feldspars, quartz, garnets and many other minerals. This report describes the experiment using the following two hyperspectral sensors: ProspecTIR, a visible near and shortwave infrared (VNIR-SWIR) sensor with 356 channels and spectral range of 0.4 to 2.5 ¦m, along with a spatially enhanced broadband array spectrograph system (SEBASS), a midwave and longwave infrared (MWIR-LWIR) sensor with 128 channels from 2.5 to 5.3 ¦m and 128 channels from 7.6 to 13.5 ¦m. SpecTIRÆs ProspecTIR system and The Aerospace CorporationÆs Spatially Enhanced Broadband Array Spectrograph System (SEBASS) are pushbroom sensors, have high signal to noise ratios, have similar swath widths and instantaneous fields of view. Examples of data collection experiment will be shown with a focus on mineral/lithologic identification and mapping along with environmental assessment in the western United States. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By Mernagh T, Large R. R, Ryan C. G, Huston D. L

The Tennant Creek goldfield is one of the largest gold producing districts in Australia, and major deposits, including Gecko, Juno, Orlando, Peko, Warrego, Nobles Nob, Golden Forty, Argo, TC 8 and White Devil have produced more than four million ounces of gold over the past two decades. Gold-copper-bismuth mineralisation at Tennant Creek occurs in lenticular, ellipsoidal or pipe-like bodies of magnetite-hematite ironstones which are hosted in turbiditic sedimentary rocks of Proterozoic age (Large, 1975; Wedekind, Large and Williams, 1989; Le Messurier, Williams and Blake, 1990; Morrison, Donnellan and Hussey, 1992).

Jan 1, 1994

By Ooms M, Scott OJ

This paper is concerned with the design and operation of storage and discharge facilit- ies for bulk solids handling. It presents an overview of the basic design philisophy emphas- ising the influence of bulk solid flow propert- ies and bin geometry on the flow patterns developed and how these, in turn, affect the reclaim efficiency and the bin structural in- tegrity and wear characteristics of both bins and chutes. The salient aspects of feeder design and operation will be discussed and the need to consider feeders as integral parts of the bin discharge system will be stressed.

Jan 1, 1978

By Sennitt C. M, Hartley J. S

The Twin Hills Gold Deposit is an example of a preserved, high level, epithermal system, with mineralisation introduced contemporaneous with deposition. The deposit is hosted within sediments of the Late Devonian to Early Carboniferous Saint Anns Formation, of Cycle 1 Drummond Basin stratigraphy, situated in central Queensland. Prior to epithermal activity in the Twin Hills region, a lacustrine fan delta depositional environment existed, together with minor tuffaceous activity. An and palaeo climate, with occasional periods of torrential rainfall, together with a basin with faulted margins, allowed alluvial fan prograda- tion. Cyclical repetitions of the fan indicate repeated faulting and seismic activity took place during deposition. Significant gold mineralisation was first intersected at Twin Hills by Metana Minerals NL in 1988, after drill testing a "blind" target outlined by geological mapping and bedrock geochemistry.

Jan 1, 1991

By J Ranford, A Harris, K Laughton

The Angas Zinc Mine (Angas) is a poly-metallic, underground mine in the Adelaide Hills that has been developed through arguably one of the most volatile financial time periods in living memory. From boom times during the commencement of the project, the global financial crisis (GFC) through the stabilisation of the operating period and then a subdued capital market for the period where mine life extension was targeted, the financial environment has always presented a different set of challenges. Indeed even the Underground Operators’ Conferences that have been held across the span of the project allude to these changes: ‘Boom and Beyond’, Launceston (2008); ‘Safe, Innovative and Sustainable’, Canberra (2011) and ‘Managing the Margin’ in Adelaide (2014).Angas gives a rare opportunity to see the entire life-of-mine of a project and its economic performance within a relatively short time frame. Angas, owned and operated by Terramin Australia Ltd (Terramin), will have undergone resource estimation drill out, feasibility study, permitting, commissioning, operating and completion and rehabilitation all within a period of approximately ten years. A number of sensitivities of the project were tested, particularly in the bankable feasibility study (BFS) stage and the aim of this paper is to identify the factors that impacted the operations profitability the most, whether they were identified preproduction or not. The key sensitivities assessed in the BFS were typical of similar studies, including operating costs, metal recoveries, capital costs, zinc prices, lead prices and exchange rates. The manner in which these sensitivities presented themselves in real life were not as anticipated and modelled in the feasibility study and were also heavily impacted by technical challenges.CITATION:Harris, A, Laughton, K and Ranford, J, 2014. Feasibility to mine completion – the real impacts on project economics, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 99–110 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By Williams P, Hender A

The 1980s witnessed a major revolution in the application of airborne geophysics to mineral exploration. The now commonplace term `high resolution aeromagnetics' (HRA) evolved from advances in survey specifications, instrumentation, data processing and imaging techniques which greatly improved the quality and geological information content of the final maps. Although initially HRA was successfully applied in `hard rock' basement terrains, eg the Archaean Yilgarn Craton of Western Australia, the technique along with the radiometric and electromagnetic techniques is now gaining wide acceptance in all geological terrains including inaccessible sedimentary rock dominated mountain belts such as New Guinea for mineral and petroleum exploration. It is also being used in more and more diverse roles away from exploration, such as environmental monitoring. The main reason for this acceptance is of course the very cost-effective surface and sub-surface mapping capabilities of the various airborne techniques. Although the three main techniques (magnetic, radiometric and electromagnetic) have been in use for some time, they are continuously being improved. Recent developments include: ò better navigational positioning using real-time GPS systems (Geographic Positioning Systems) such as Picodas Navigation Systen (PNAV); ò the use of magnetic gradiometer systems; ò improved sensitivity and sampling rate of magnetometers; ò increased use of ultra detailed low level (

Jan 1, 1996

It is difficult with inadvertent explosions to establish fundamental data, especially of original dust, of pressure, temperature etc. and of ventilation oscillations, as exposed personnel rarely survive. Retrospective data from explosions must be derived from damage, from fatalities, from ventilation analyses, from analyses of dusts and other indications of temp- erature and duration of temperature. The five disastrous explosions selected for analysis provide examples of what data can be established as to the cause and extent of explosions. Such information is required for legal etc., inquiries subsequent to explosions, but most importantly to give the best guidance for avoidance of possibility of further Disasters.

Jan 1, 1981

By K H. Esbensen

The Theory of Sampling (TOS) has contributed significantly to chemometrics by allowing data analysts to become more aware of total measurement uncertainty as total sampling error + total analytical error. This has allowed a new view on, for example, validation of multivariate data models and their performance. This keynote focuses mostly on the reverse perspective: how can chemometric multivariate data modelling be of help in an augmented sampling context? The basic principles of multivariate data analysis are presented and application examples are outlined from several areas in the geosciences to facilitate answers to the question posed, including a geochemical multivariate anomaly concept defined by a multivariate background model. Applications from geochemical prospecting, geochemical mapping, environmental chemistry and anthropogenic outlier recognition are outlined, as are the interdependent relationships between geostatistical modelling (variographics) of singular variables versus linear combinations of a multitude of variables, in chemometrics called scores. The potential synergy between chemometrics and TOS is far from exhausted at this time; much work remains.CITATION:Esbensen, K H, 2014. Theory of sampling in a multivariate perspective – what can chemometrics contribute?, in Proceedings Sampling 2014 , pp 7–10 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

By J Hudson

Autogenous (AG) and Semi Autogenous (SAG) grinding mills are the conventional selection for large-scale grinding circuits. It is accepted that these forms of comminution are not the most energy efficient available. This efficiency combined with escalating energy prices, steel prices and the requirement to process larger, lower grade deposits has necessitated that better comminution techniques are found to challenge the dominant position of AG/SAG mills in the grinding circuit. Recent advances in high pressure grinding rolls (HPGR), particularly in terms of roll surface protection have meant that, depending on the application, an economic alternative is available to the large diameter AG/SAG mills. Mining companies now recognise the potential benefits of HPGR and so they need proper assessment in the design of new or upgrade of existing grinding processes. Of course, the answer to the question AG/SAG or HPGR is not straightforward and the impact of the grinding process on the whole metallurgical process needs to be evaluated. Clearly this is a complex decision to make and requires substantial metallurgical knowledge, test work, and objective analysis. The perceived downstream processing benefits will differ between different plants depending on the ore type and processing conditions. The optimal design of the comminution circuit requires that a robust methodology is followed to objectively characterise the ore, size the equipment and determine the downstream processing benefits. The paper gives a brief comparison of the capital and operating costs for both grinding systems, and then outlines the appropriate test work that is required to make an informed decision.

Jan 1, 2006

By McClarnon D. J

This paper aims to provide the reader with an insight into the field of computer graphics and Virtual Reality (VR), and show how both have been applied to the general area of Free Steered Vehicle (FSV) operations underground. It first explains this developing computer technology and explains its advantages over existing CAD based solutions. This paper deals with the graphical applications and implications of building models within a computer's memory. It then continues to describe the problems with Free Steered Vehicle operations. The work already carried out in the field of VR is explained, and the production of a VR system addressing the problems with fitting cameras to aid the driver's field of view is detailed. Another possible use of VR is also explained - the concept of risk regions, demonstrating its uses in the examination of proposed operational methods. Examples of possible uses are given, and its potential advantages over existing methods discussed. A case study of a computer-generated video involved with the safety of operations of FSVs is also presented. This addresses the precautions that pedestrians should take to ensure safe working in areas where FSVs are operating. This paper then concludes with possible further applications for computer graphics and VR, and the on-going research into these two technologies.

Jan 1, 1995

By Yanagase T, Nakamura T, Ueda Y

The possibility of removing the phos phorus and sulphur contained in steelmaking slag has been studied by observing directly through the microscope melts heated on Pt- filaments. After a CaO crystal was placed in the molten slag, distributions of P, S and other elements formed around the CaO crystal were determined with the aid of EPMA. The results indicated that a layer of 2CaO SiO2 is formed on solid CaO in CaO-Si02 melts. Then between CaO and the newly formed compound the molten slag tends to migrate through cracks. For higher Fe 2 03 contents, the layers of the compounds 2CaO.Si02 and 3CaO SiO2 formed around the CaO crystal are not continuous but look more like particles, which promotes the dissolution of CaO. Phosphorus in slag was found to be enriched in the 2CaOòSi02 layer. Phosphorus in the 2CaO SiO2 phase is not related to the primary slag composition, being about 5-7% P205.. Sulphur in slag,as well as the phos- phorus,was concentrated in the 2CaO.Si02 phase. Disintegration due to weathering observed for slags produced in these investigations appeared to be due principally to hydration of lime.

Jan 1, 1980

By R Pie, J Crusius, P Whittle, J J. McNee

The Main Zone and Waterline pit lakes at the Equity Silver Mine near Houston, BC (Canada) are the sites of an ongoing three-year government- and industry-funded research program. In order to assess the feasibility of various bio-remediation strategies, field-scale manipulations were conducted using enclosed mesocosms (limnocorrals). Two manipulation strategies were tested: addition of algal nutrients (phosphate and nitrate) to Main Zone Pit surface waters; and addition of algal nutrients (surface waters) and dissolved organic carbon (deep waters) to the Waterline Pit. Nutrient addition was conducted in order to stimulate algal production and enhance metal scavenging by biogenic particles, while dissolved organic carbon (ethanol) was added to increase oxygen demand and foster the development of sulfate reduction in pit bottom waters. Fertilisation resulted in rapid growth of natural phytoplankton populations in the surface waters of both pits. In the Main Zone Pit, the stimulation of algal growth resulted in the pronounced removal of both dissolved and total metals (Zn and Cu) from surface waters, with higher rates of metal removal being observed at higher nutrient additions. Metal removal could be attributed to the scavenging of dissolved metals by biogenic particles and subsequent particle settling. A similar pattern of removal from surface waters was observed in Waterline Pit (Zn and Cd). The addition of ethanol to deep waters in Waterline Pit was effective in promoting sulfate reduction in the lower layer. The development of reducing conditions resulted in near-quantitative removal of dissolved Zn and Cd, presumably as secondary metal sulfides. Iron, As and Ni profiles in Waterline Pit exhibited no evidence of removal from either surface waters or bottom waters. Collectively, the results demonstrate that the passive forms of bioremediation tested in these pit lakes may be effective for whole pit-lake remediation.

Jan 1, 2003

By C Reed

Titaniferous magnetite deposits are a significant source of vanadium for use in high strength steel alloying and other chemical applications. The mineralogy of the deposits varies markedly and the ore characteristics strongly influence the process route selected and the metallurgical outcomes. Characterisation of the ores reveals the presence of magnetite, ilmenite and other minerals such as spinel hematite and goethite with variable degrees of weathering along with weathered products of host rock. The standard processing route is to crush, grind and magnetically recover a concentrate for salt roasting to produce a soluble vanadate. Ore beneficiation is practised to generate an iron based mineral concentrate containing much of the vanadium with low silica levels of two per cent. Typical processing problems encountered are fine liberation size, over grinding of the magnetite and variable response to magnetic separation resulting from the weathering profile. Beneficiation options are restricted, and generally focused on producing a combined iron and titanium rich concentrate containing vanadium due to the fact that ilmenite and magnetite and their products of weathering are magnetic and have similar specific gravities making their separation difficult. The ilmenite usually contains low levels of vanadium making its separation highly desirable from the iron mineralisation containing higher levels of vanadium. Salt roasting of vanadium ores followed by water leaching has been the standard processing route for many years. The cost of suitable sodium salts, availability of capital and increasing energy costs and energy availability are critical factors in determining the viability of aspiring vanadium producers. To date, only Windimurra has acquired full capital funding, secured energy and sodium salt supplies at suitable cost that enable the construction of the project. Low overall recoveries of vanadium to concentrate roasting at up to 1200¦C are critical cost issues. In this paper, factors influencing the recovery of vanadium are reviewed and emerging processing trends explored. The important features of the processing of titaniferous magnetites have been condensed from the literature, published works, company websites, our own work and personal communication.

Jan 1, 2008

By Olofsson O, Durance M-V, Villeneuve J

Modelling of the Sala Agitated Mill (SAM) using a simplified solution to the population balance approach has been carried out. The rate of breakage is modified by the mill power, providing predictions of the resulting product size distribution for different grinding conditions and mill sizes. The power of the mill is estimated by a physically derived function, using an assumption that the mill power consumption mainly arises from the ball to ball friction within the mill. The grinding efficiency, depending on the media ball size and pulp density is approximated in the model. Experimental work on grinding a complex sulphide ore using a pilot scale SAM 7.5 has been carried out. Good agreement has been found between the data from the test campaign and the simulated values. The model has also been validated with experimental data from a pilot grinding of calcium carbonate and from an industrial mill. The model is included in the USIM PAC simulation software.

Jan 1, 1995

By M Scoble, W S. Dunbar

This paper reviews methods for grade estimation in short-term mine planning for block caving. Two particular tools are used: Ordinary Kriging and Simple Kriging with moving averages. It is also considered the influence of draw characteristics on the grade estimation process. Reference is made to mine case study data and analysis. These demonstrate that operational grade estimation is not a trivial process. It must take into consideration: the grade variability (in terms of ore and dilution), sampling interval, geological and geotechnical characteristics, geometrical layout and draw characteristics. Significant improvements appear possible in short-term planning if variogram analysis, as well as kriging methodologies, are introduced into the operational grade estimation process.

Jan 1, 2000

Minerals similar to the indicator minerals used in kimberlite exploration are widespread in the Cainozoic alkali basalts of north Queensland. Magnesian ilmenite, pyrope garnet, chrome diopside, chrome spinel, phlogopite and zircon were recovered from most of the localities examined. The occurrence of these minerals creates significant problems when indicator minerals are used for diamond exploration. Basaltic ilmenite is visually similar to kimberlitic ilmenite. Untransported grains are rounded and have pitted surfaces. Basaltic ilmenite grains often have exsolution lamellae and reaction rims of titanomagnetite. Although kimberlitic and basaltic ilmenite are chemically similar, basaltic ilmenite grains are usually less magnesian than their kimberlitic counterparts. Basaltic ilmenite contains very little Cr203. Pyrope garnet occurs as megacrysts and in a variety of xenolith lithologies in north Queensland basalts. Most basaltic garnet is Cr-poor and comparable with kimberlitic garnet from Groups 3 and 5 of Dawson and Stephens (1975). Wine-purple, chrome-bearing garnet is common in kimberlite but rare in basalt.

Jan 1, 1984

By P S. R Reddy, V N. Misra

The iron ore deposits in India are rich in iron content but usually contains high alumina and silica. The current industrial practice results three products namely lump, fines and slimes. The lump and fines with or without beneficiation are directly fed to the blast furnace and sintering plant respectively while the super fines or slimes are presently discarded as tailings. Around eight million tonnes of iron ore slimes estimated as being 15 - 20 per cent by weight of run of mine ore containing ~48 - 62 per cent Fe, is discarded every year causing huge loss to the Indian iron ore industry. In addition, these slimes stored in massive tailing ponds pose enormous environmental and ecological problems. Extensive investigations have been carried out on three iron ore slimes generated at Barsua, Bolani and Meghahatuburu iron ore mines of India. The studies include physical, chemical, mineralogical characterisation and beneficiation studies adopting conventional hydroclyclone and wet high intensity magnetic separator. The characterisation studies have indicated that most of the gangue minerals are accumulated in finer fractions. The studies on hydrocyclone and magnetic separation had indicated that an iron concentrate of 61 - 65 per cent Fe could be obtained by recovering 59 - 78 per cent of the iron values present in the slimes. Depending on the nature of the slimes the alumina and silica levels have been brought down to 2.5 and 1.0 per cent respectively. The effects of different operating and design variables along with detailed characterisation studies have been highlighted.

Jan 1, 2002

By M, C A. RosiFre, R C. Figueiredo e Silva

Jaspilites and underlying basalt contacts of the Archaean volcano- sedimentary Grpo Parß Group, Carajßs, host giant iron mineralisation in the ~100-km long, E-W trending Carajßs fold. Preliminary, unpublished geochronological data point to a Palaeoproterozoic mineralisation event. Geochemically, jaspilites are typical volcanogenic banded iron formations. Basalts exhibit evidence of spilitic seawater interaction. Iron-associated hydrothermal alteration of mafic rocks was induced by fluid infiltration in amygdales, with development of chlorite- and hematite-dominated zones. In the case of jaspilites, iron mineralisation encompasses: partial replacement of jaspilitic microcrystalline hematite by blasts of martitic magnetite; jasper recrystallisation, producing fine-grained, hematite-free granoblastic quartz; martite recrystallisation, forming lobate¦subhedral hematite; pervasive porosity development by quartz-chert leaching; incipient cavity filling by microlamellar hematite; and advanced filling by coarser, euhedral and comb-textured, tabular- shaped hematite.Peak hydrothermal ore textures indicate typical epithermal-crust conditions, supported by preliminary fluid-inclusion calculations at 160 - 200¦C. Such temperatures and extreme fluid-to-rock ratios during alteration must have exceeded the ambient metamorphic conditions, with the infiltrating fluid relatively hot and capable of leaching SiO2. Therefore, mineralisation developed over exhumed, Archaean, brittly deformed rocks, with mineral associations representative of very low- to low-grade metamorphism. Considering that chlorite (¦talc) abounds in mafic rocks; hydrothermal albite is developed; dolomite fills veins and vugs; the typical rare-earth-element (REE) pattern of jaspilites is significantly modified in higher-grade hard hematite ores (higher LREE); pyrite, copper sulfide minerals and rare gold occur in association with carbonate-quartz-rich alteration zones, it is suggested that an alkaline, H2O-Fe-CO2 mineralising fluid dominated, also containing species like S¦Cu¦Au. Peak-mineralising conditions are likely to have resulted from a single, evolving fluid, via incipient- through advanced-stage alteration phases. The porous, high-grade soft hematite-type ore (SH), rich in microlamellar and anhedral hematite, must have derived from interaction with this relatively hot SiO2-leaching fluid, whereas the high-grade massive hard hematite-type ore (MH) developed due to closer fluid-rock temperature equilibrium conditions, attained by mineral reactions, with relative increase in the Fe/Σcations ratios allowing the precipitation of subhedral-tabular hematite that partially cements the soft-hematite ore. SH and MH hematite ore types must thus reflect intermediate and high fluid:rock ratios, respectively. Since the N5 deposit is to date understood to contain the largest amount of the MH ore, its units are interpreted as the loci of the highest fluid:rock ratios in the district. Preliminary mineralogical information regarding the S11 deposit of the Serra Sul (south range) implies higher-temperature conditions. The near-equant grain size and the granoblastic intergrain relationship, coupled with the presence of riebeckite, augitic pyroxene and garnet, suggest hornfels textures. The data collected, though still relatively sparse, permit the speculation that the immense driving force for the Carajßs world-class iron deposits was a relatively shallow, igneous-related hydrothermal system. If such a model is correct, then the Carajßs Palaeoproterozoic iron deposits could represent an end-member of the iron oxide-copper-gold hydrothermal system in the province.

Jan 1, 2005