Search Documents

By Lawson F

Arsenic-containing waste was dissolved into molten slags and the leaching behaviour of the quenched arsenic-doped slags (containing up to 2.3 wt per cent arsenic) was ascertained to evaluate the potential of this method as a means for arsenic disposal. The leaching behaviour was evaluated using acetic and sulphuric/nitric acid based solutions.From short-term (18 hour) leach tests, the amounts of arsenic in the leach solutions were found generally to decrease with an increase in the Fe(III)/Fe(total) ratio of the slag or an increase in pH of the leach solution. The amount of arsenic in solution increased with an increase in the slag basicity, the slag arsenic concentration or the surface area of the slag exposed to the leach solution. From longer term leach tests (up to 40 weeks) in the pH range 5 to 8, the arsenic remaining in the leach solution was believed to be controlled by sorption processes. The sorbent was an iron oxide-rich material which had the capacity to lower the arsenic concentration in the leach bottles to well below 1 ppm in some cases. At a leach solution pH over 9, the arsenic concentration in the solution increased with time, although the rate of solubilisation was much slower due to the high pH.Slags have the potential to stabilise arsenic and prevent it entering the environment provided attention is paid to the slag chemical composition and oxygen potential.

Jan 1, 1996

By Sinha DK

Coal Mining in India had been confined in the past primarily to two or three coalfields. Unscientific mining has led to huge degradation of land including massive subsidence of strata and disturbances of water tables to a wide extent. This has caused problems not only in flooding of mines from surface water but also in further planning of the surface drainage for current mining activities. Now, therefore, surface hydrology and land-use potentialities of the area have been endangered inflicting severe damage to the overall environment and ecology of the area. The paper Discusses certain investigative aspects of the problems highlighted as above in one of the coalfields, and encompasses mainly the following areas : 1) Quantitative estimation of the damage already done to the natural surface drainage system. For this purpose damage to topography and drainage for the last fifty years have been made out through the aerial photographs and topographic map sheets 2) Analysis and comparison of different states of such photographs are carried through to indicate the extent of damage to the hydrological conditions inducing undesirable changes in its land-use pattern. Based on the analysis, concrete suggestions are made to restore the water drainage system which will be most suitable for future mining in the area containing high grade coal. The design and planning of the drainage system is based on the total system approach including the cost benefit analysis as well as hydrological considerations.

Jan 1, 1988

By Perring CS, Barnes SJ

The nickel exploration boom of the late-1960s and early-1970s led to the discovery of numerous komatiite-hosted nickel sulphide deposits, associated with variably serpentinised bodies of olivine-rich cumulates. Subsequent research has shown the importance of volcanological processes to understanding the genesis of these deposits. Crucial developments have come through consideration of the fluid dynamics of magmas and magma-crystal mixtures, through observation of the dynamics and geometry of modern day basaltic lava flows, through application of theory and experimentation on the kinetics of crystal growth from magmas, and most importantly from extensive detailed field mapping of komatiitic sequences in the Yilgarn Block and elsewhere. From these studies has emerged a new integrated view of the volcanological setting of komatiite-hosted deposits, and a recognition that a complete continuum of deposit types exists. Nevertheless, komatiite associated magmatic nickel deposits generally fall into two overall types based on the nature of the sulphide ore. In the first type the bulk of the ore is either massive Fe-Ni-Cu sulphide or a variable mixture of massive sulphide and an ore characterised by olivine crystals in a continuous matrix of sulphide occupying between 30 and 75 per cent by volume of the rock (called Matrix Ore). Nickel grades of massive sulphide ore range from 2 - 20 wt% and those of the matrix ore generally fall in the range 1 - 5 wt% (average 2.5 wt%) Ni/Cu ratios of the sulphide fraction are generally >10.

Jan 1, 1996

By Caivin JS, Freeman CJ

The Fairbanks Mining District in central Alaska was discovered in 1902 and since then approximately 7.5 million troy oz of placer gold, 250,000 troy oz of lode gold, and several thousand short tons of antimony and tungsten hap been produced from an area of about 1000 km . Historic lode production was from high grade gold-quartz veins that averaged 1.3 OPT free milling gold. Five main types of mineral deposits' are recognized in the district. I. Conformable, stratabound volcanogenic zinc, antimony, lead, and copper sulfides in places containing gold, silver and tungsten in bimodal metavoleanics (Cleary Sequence). II. Complex precious metal-bearing lead sulfosalt-quartz veins in Cretaceous granitic intrusives. III. Tungsten skarns adjacent to granitic intrusives. IV. Gold-bearing polymetallic sulfide-quartz veins crosscutting metavolcanics and metasedimentary units of the Cleary Sequence. V. Antimony-bearing gash veins along axial plane shears in various lithologies of the Cleary Sequence. Type I and Type IV mineral occurrences are currently being evaluated as low. grade bulk tonnage (target model 16-20 'million tons of 0.05 to 0.15 OPT)'and high grade moderate tonnage (target model 0.5 to 2.5 million tons of 0.5 OPT) gold deposits. The host rocks for Type I mineralization occur over a 30 km strike length and are at least 300 meters thick. Stratigraphic, structural, fluid inclusion, and isotopic data suggest that the Type IV mineralization is related to remobilization of Type I

Jan 1, 1987

By G Power

The successful implementation of sublevel caving (SLC) at Ridgeway Gold Mine (Ridgeway) requires the technical aspects of caving and flow behaviour to be understood. Cave propagation must be controlled and continuous to allow safe extraction of ore below. The understanding and use of processes to manage granular flow behaviour are also required to ensure economic metal resource recovery. Caving and flow technologies are thus critical to the economic viability of the application of the SLC mining technique to Ridgeway Gold Mine. At the time the Ridgeway SLC design was approved there were significant technical uncertainties associated with cave mining methods, including the SLC mining method in competent rock masses. This was in spite of the fact that caving is a relatively low cost mining method. Unique features generating technical risks at Ridgeway include: the fact that the orebody is blind (550 m below surface); highly competent cap rock (RMR >50); and high aspect ratio (height to width ratio of 3:1). Due to the presence of these unique features Ridgeway is considered to be beyond the current state-of-the-art in SLC mining technologies. The success of the technique at Ridgeway to date has indicated that blind SLC mines in strong rock mass can be operated safely and productively, if the technical risks are understood and properly managed. The risk management process was defined by the use of a formalise process to identify and assess the risks to the mine. The major mining related risks were formalised into Major Hazard Management Plans (MHMP) which contained a description of the risk, early triggers indicating the creation of a hazard and a series of agreed responses to be automatically initiated in the event of each trigger occurring. This paper outlines the following with respect to the critical technology areas of caving and flow: international industry, state-of-the-art technology; gaps in the application of this technology; the application of risk management, new processes developed at Ridgeway to bridge these gaps, including issues encountered; and trials and experimentation conducted to develop the new processes.

Jan 1, 2003

By Y Potvin

Risk assessment in the mining industry is currently a topic of great interest with risk methodologies being increasingly applied beyond the traditional areas of finance and feasibility to analyses of risks due to various physical hazards including chemical, electrical, mechanical and geotechnical sources. The application of risk analysis and evaluation techniques to the management of personnel safety is being promoted by both industry and regulators but, particularly for geotechnical hazards, often there are inadequate databases for a meaningful quantitative calculation of risk. In Western Australia over the decade 1987 - 1997, the annual fatality rate for underground mining has averaged at approximately 1.3 in 1000 employees with rockfalls/rockbursts accounting for over half of these deaths (Prevention of Mining Fatalities Taskforce, 1997). Recent improvements have been made since this time, perhaps halving the annual fatality rate, mainly due to industry improving ground control measures and implementing various recommendations from the Prevention of Mining Fatalities Taskforce (1997). However there still remain a large number of unknowns when trying to address the complex area of geotechnical risk in mining. Risk calculations require information about the source of the hazard, the people or assets exposed to the hazard (the æelements at riskÆ) and the effects on these vulnerable elements if the hazard actually occurs (the potential consequences). To date, little information has been available on the exposure of mining personnel and equipment to underground hazards other than occupational safety studies on chemicals, heat, dust, etc. This paper concentrates on underground geotechnical risks and presents a data collection and rating system for the exposure of both the underground workforce and equipment to rockfalls and rockbursts. The methodology considers exposure times, personnel protection levels and hazard proximities to give exposure ratings for the major underground mining activities and hence rate different locations within a mine. This exposure methodology is then applied to the workforce and production/ development cycles in an actual WA underground mine, creating a snapshot map of differing levels of personnel exposure across the mine.

Jan 1, 2003

Kumba Iron OreÆs Sishen Mine is one of the worldÆs largest iron ore mining operations situated in the Northern Cape, South Africa. It produces 29 million tonnes of iron ore products per annum using a dense medium separation (DMS) beneficiation process. Kumba is currently commissioning the Sishen Expansion Project (SEP) which will produce a further 13 Mtpa product through a jigging beneficiation process. The products from the Sishen Mine are highly sought after and consumed by domestic and various European and Asian customers. During beneficiation iron ore slimes are generated and discarded as waste material to the slimes dams. A study was initiated in 2005 to investigate processes to beneficiate these slimes to saleable products û prompted by the current high demand for iron ore products and the high grade in the Sishen slimes thickener underflow of approximately 54 per cent Fe. Initial laboratory scale test work indicated that a 66.5 per cent Fe iron ore concentrate could be produced from the Sishen slimes thickener underflow through a process of classification, two stage wet high intensity magnetic separation (WHIMS) and five stage flotation. This process, however, did not produce the desired results during pilot plant testing and numerous alternative process routes were investigated. The process that did achieve the desired product grade of 66.5 per cent Fe at economically feasible product yields consisted of two stage WHIMS using SLON magnetic separators. Results achieved indicate that the thickener underflow slimes can be upgraded from 54 per cent Fe to 66.5 per cent Fe at a product yield of ca. 40 per cent. Product yield could be increased through the further beneficiation of the SLON tails. The Sishen slimes thickener underflow production rate is ca. 3 Mtpa û resulting in a potential concentrate production of ca. 1.2 Mtpa. The slimes concentrate will be fed to a pelletising plant that will produce 66 per cent Fe pellets destined for domestic and or export markets.

Jan 1, 2008

By D Burgess

Since the days of mandatory high cost pilot plant testing in 6 ft + 2 ft SAG mills autogenous griding/semi-autogenous grinding (AG/SAG), mill specific energy is now calculated by various empirical formulae and pilot testing carried out in small laboratory mills. Barratt (1989) described a method using Bond Indices than adding a single factor of 1.25 to arrive at the AG/SAG specific energy. In 1991 the Canadians developed the SAGPower Index (SPI), test using 2 kg of material in a 300 mm diameter mill. This test has been further developed by Starkey, Hindstrom and Orser (2006). This test now includes a Bond Ball mill work index test.The Macpherson test is still being offered by some testing facilities. This dry test requires at least 180 kg of material.Morrell (2004) formulated an AG/SAG specific energy generator based on a drop weight index Value (DWi). This DWi value is related to the Ab parameter and the material specific gravity. Morrell reconfigured the BondÆs Third Theory formula to cause extra power requirements to be inputed. This technique incorporates the material specific gravity (SG). The AG/SAG specific energy values produced using this method are susceptible to higher values of crushing and rod mill work indices.This paper offered describes a more simple method to generate AG/SAG specific energies. This programme incorporates Bond work indices, the JKMRC parameter Ab measuring impact breakage and the parameter ta measuring the abrasion rate, then employs a series of efficiency values nominated for each transition size (AG/SAG T80). These efficiency values have been compiled over the years from actual operating plants and documented reports.CITATION:Burgess, D, 2012. A method of calculating autogenous/semi-autogenous grinding mill specific energies using a combination of bond work indices and Julius Kruttschnitt parameters, then applying efficiency factors, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 37-44 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By L M. van Niekerk

The mining of iron ore is a high volume low margin business because the value of this commodity is significantly lower than that of base metals. The main metallurgical challenges in most of the iron ore projects proposed for treatment nowadays have been in finding the optimum flowsheet for the treatment of magnetite ores, mixed magnetite-hematite ores and even ores that have banded ironstone formations (BIF). The associated plant designs incorporate very high capacity milling systems to grind the ore down prior to magnetic separation and in being highly capital intensive requires substantial investment in mega processing plants with associated infrastructure to mill down the run-of-mine ore to the desired treatment size for upgrading.To minimise the cost of infrastructure, better beneficiation techniques and technologies are being sought to assist in reducing upfront ROM feed to allow for reduction in overall treatment plant footprint necessary in extracting the desired downstream product. This paper discusses such beneficiation techniques and advancement in technologies for the upgrading of coarse and fine iron ore utilising dense media separation (DMS), jigging, wet magnetic separation, dry magnetic separation, flotation and x-ray processing.Another group of iron ore projects involve the mining of hematite ore below the water table. Often the mined ore is wet and sticky. This combination requires high capacity processing of feed material utilising large scrubbers or attritioning units to effectively remove the slimes component present in the feedstock. The fines removed, usually below 1 mm, are then discarded in large tailings storage facilities. Approaches to recovering the saleable material contained within these fines will also be investigated in this paper. This not only implies possible reduction in slimes discard footprint, but also holds potential benefit in augmenting overall yield and recovery of hematite product.CITATION:van Niekerk, L M, 2013. Fine and coarse iron ore beneficiation - An evaluation into global technologies and techniques, in Proceedings MetPlant 2013 , pp 584-598 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

On Wednesday 11th November, 1970, a series of violent explosions occur-- red within No.1 Basic Oxygen Steelmak- ing (B.O.S.) furnace at the Whyalla Works of the Broken Hill Proprietary Co. Ltd., (B.H.P.) when the furnace was moved immediately prior to tapping. Water from a burnt out flux chute had flooded the bath while the furnace was tilted slightly towards the tapping side waiting to tap. Although no one was injured, dam- age in excess of $54 000 was caused to the hood and superstructure. The water hydrated the burnt dolomite refractory lining some of which sub- sequently collapsed exposing bare fur- nace shell over part of the cone.

Jan 1, 1975

By J Aitchison, G Clarke

A reappraisal of the stratigraphy, new regional kinematic analysis and thermobarometric data allow a new interpretation of the metamorphic zoning and tectonic structure of the Upper Eocene high-pressure metamorphic core complex of northernNew Caledonia allow a three steps evolution to be proposed: 1. subduction and understacking of previously thinned continental crust elements; 2. subduction blocking due to the crustal thickening; and 3. crustal thinning and extensional detachment during the diapir-like uplift and unroofing of the eclogitic core. Steps 2 and 3 may be partly contemporaneous. Such a model accounts for the thermobarometric and radiochronologic data, and also for the weakness of substratum deformation during the emplacement of the ophiolitic nappe

Jan 1, 1995

By Waddell S

A new procedure has been developed for the direct determination of metals loaded on activated carbon. It involves preparation of a suspension of the powdered carbon in water, followed by direct sampling of the suspension with a micropipette,and analyses by atomic absorption spectroscopy using carbon rod atomization. Advantages of the method include the simplicity of sample preparation and the ability to provide a complete metal analysis in 1 - 2 hours. This enables carbon-in-pulp operators to respond quickly to changes in plant efficiency arising from carbon fouling. The successful application of the method has been demonstrated for gold, copper, nickel and iron. Other elements to be surveyed include calcium, magnesium and silicon.

Jan 1, 1984

Exposure to respirable contaminants in mine atmospheres has long posed a serious hazard to miners. The control of these hazards, some of which can have sudden and catastrophic effects and some others, slow and long enduring consequences, has been a major concern for labor, management and government alike. This concern has manifested itself in four primary mechanisms of control -- (1) regulatory control through minimum standard setting by the passage of mine health and safety laws, (2) engineering control through design and operation of mines according to the best recommended practices, (3) medical control through periodic physical examinations, wearing personal protection devices, etc., and (4) legal and social control through workmen's compensation laws for occupation related health rleterinratinn_

Jan 1, 1988

Recent data contributions to New Zealand Mesozoic terrane geology confirm the consensus interpretation that New Zealand grew by the progressive addition of material by plutonic and accretionary processes along the Gondwana margin. The data also (1) emphasise the discontinuous but inter-related nature of these processes of continental growth, (2) better establish a direct Gondwana correlation of the Western Province and probable Gondwana provenance of at least some of the Eastern Province, (3) suggest specific times and places when passive or strike-slip rather than subduction regimes are recorded along the south Gondwana margin, and (4) potentially lead to interpretations emphasising parautochthonous rather than far- travelled relationships between many New Zealand terranes.

Jan 1, 1995

The Koongarra uranium deposit was discovered in August 1970 by Noranda Australia Limited. Denison Mines Limited acquired the rights of ownership in October 1980 and has continued the 'struggle' to bring the proposed mine, containing approximately 13 300 tonnes of U308 of Indicated ore and having a value of $1 billion (1984 dollars), into operation. During the 14 years that have passed, the owners have found it necessary to deal with numerous Federal, State and Territory government departments, aboriginal representatives, handle thousands of communications, attend and convene countless meetings and spend millions of dollars. This paper addresses the history, the requirements, the problems and the costs to date for what - no return.

Jan 1, 1984

Following a period or small-scale activity a joint venture was formed between Ceramco Limited of New Zealand and Georgia Kaolin Company of USA. The initial concept was to process clays for the paper industry but it soon, became apparent that insufficient markets were attainable for the grades of china clay that could be produced for an economic unit. Ceramco Limited acquired the Georgia Kaolin interest in 1975 and proceeded to search for a market, of markets, that would: 1. utilise the unique properties of the product, and 2. enable a viable operation to be created. This paper describes the mineral deposits, the process, the properties of the product, and the marketing methods of New Zealand China Clays.

Jan 1, 1984

The low grade Mount Charlotte orebody was first mined with minimum capital expenditure by mechanised cut and fill stoping. The lower block was prepared simultaneously for open stoping by shaft sinking and installing another crusher and services. Similar development for the third block was discouraged by economic factors and reduced tonnage. Decline develop- ment required less capital and opened up ore reserves commensurate with advance, providing flexibility to stop operations without commit- ment: A 1 in 7 decline measuring 4.25m x 5.5m to accommodate standard Euclid 25 tonne dump trucks was developed south of the orebody. A fleet of four trucks average 12 loads each per shift over a haul distance of 700m.

Jan 1, 1973

By Georgi H, Farquhar J. W, Lorrigan A. N

The potential for major new lenses of Volcanic Hosted Massive Sulphide (VHMS) beneath the existing Rosebery Deposit is extremely high. Recent deep drill hole intersections of massive sulphides, including 22 in true thickness at 24 per cent Zn, may significantly extend the life of the Rosebery Mine. The Rosebery Ore Deposit is located within Australia's most prospective VHMS mining district, the Mount Read Volcanic (MRV) arc of western Tasmania (Figure 1). The MRVs are a 10 - 15 krn wide arcuate belt of lavas, related intrusives and volcaniclastics. Rosebery is a major Cambrian volcanic hosted Zn-Pb-Cu-Ag-Au rich deposit which has been over-printed by Devonian deformation and granitoid alteration resulting in local rcmobilisation of the ore. The Rosebery Mine Sequence is composed of an east dipping and east facing, predominately felsic sequence of rhyo-dacitic volcaniclastics, epiclastics, sediments and shale lenses more than 500 in thick. This sequence is bounded by two, low angle (35 - 40¦), east dipping thrust faults, the Rosebery Fault to the west and the Mount Black Fault to the cast. The Rosebery Mine lithologies are summarised in the following table: Hangingwall (HW) Polymictic, quartz, feldspar-phyric epiclastics. Black Slates Graphitic, pyritic mudstones. Host Rocks Turbiditic mudstones and sandstones. Footwall (FW) Feldspar-phyric, pumiceous, mass-flow breccias. Cambrian, quartz-feldspar, porphyritic sills intrude this sequence at all levels. Thin, Jurassic, dolerite dykes also occur throughout the mine. Widespread quartz, sericite and chlorite alteration occurs in the FW. This alteration is manifested as quartz-augen schists beneath the orebody. The Host Rocks are pervasively altered with silica, sericite, chlorite and pyrite. Intense carbonate alteration occurs within the orebody, whereas chlorite and pyrite alteration is commonly concentrated directly beneath it. Cambrian volcanogenic alteration is over-printed by three major Devonian, granite-derived, assemblages. These are massive to quartz veined tourmaline, pyrrhotite-pyrite and magnetite-chalcopyrite. Though the Devonian granite has not been intersected in deep drill holes or in mine workings, there is good evidence that it exists within a kilometre of the deposit. The Rosebery orebody is structurally complex when compared to many other VHMS deposits. Evidence for Cambrian growth faulting has been found at the North End of the mine (B lens) where displacement of ore lenses occurs without corresponding displacement of the overlying Black Slates. A well defined cleavage exists throughout the mine, dipping at 28 to 50¦E. East dipping shear zones are also obvious in all parts of the mine workings and reverse movement is evident on many of these.

Jan 1, 1993

By W G. Rowley

The Fortescue Metals Group story began in 2003 with a vision to establish an infrastructure project that would connect the stranded iron ore deposits of the Pilbara region of Western Australia with the steel mills of Asia. Following exploration successes in the Chichester Ranges using their new exploration model, Fortescue established significant iron ore resources at Cloudbreak and Christmas Creek during 2004 and 2005. By May 2006 the definitive feasibility study for mine, rail and port was completed, many of the key government approvals had been obtained, product development and market acceptance were complete and 1.07 Bt of total proved plus probable iron ore reserves were defined to support a 20 year mine life from the Cloudbreak and Christmas Creek deposits. Project construction commenced in September 2006 following a successful $3.2 billion capital raising. By April 2008, the mine and processing plant at Cloudbreak were completed along with the Herb Elliott port facility at Port Hedland and 256 km of heavy haul railroad linking the mine with the port. Mining of overburden commenced at Cloudbreak in late 2007 and by 15 May 2008 the first shipment of iron ore had departed for China. In the first 12 months of operation total shipments amounted to 24.6 M wet metric tonnes with weighted mean composition of 58.9 per cent Fe (64.4 per cent Fe calcined), 4.3 per cent SiO2, 2.0 per cent Al2O3 and 0.047 per cent P. Exactly 3.5 years between the Cloudbreak discovery hole and commercial production. The project success depended on many technical breakthroughs including a new exploration model, application of the surface miner as the main mining production unit, design of a new marketable fines product called æRocket FinesÆ, a highly efficient ædesandÆ flow sheet for upgrading of 2.4 per cent alumina run-of-mine to 1.9 per cent alumina Rocket Fines, 40 t axle loads for the heavy haul railway and a high capacity-highly automated port facility.

Jan 1, 2009

By D A. Deglon

Solids suspension is important in the design and operation of mechanical flotation cells, and is a necessary precondition to particle collection. Most of the fundamental hydrodynamic research that incorporates some aspect of solids suspension was done by Arbiter, Harris, and co-workers, or Schubert and co-workers. However, a need for research into solids suspension in mechanical flotation cells exists, since very little has been done since the late 1980s; a time that also coincides with the advent of round mechanical flotation cells and the subsequent dramatic increases in maximum flotation cell sizes. In this work, concentration profiles and critical impeller speeds, Njs, were measured in a 0.124 m3, round cell fitted with a 0.150 m, Bateman impeller mechanism. Two solids size fractions (75 - 106 and 150 - 250 ¦m) were tested, in ungassed and gassed conditions (JG = 0, 1 cm/s) and at various impeller speeds (300 - 900 rpm). The effectiveness of solids suspension was quantified in three ways in terms of extent of off-bottom solids suspension, suspension height (extent of solids distribution), and variation within the solids distribution, which together present a complete quantitative picture of solids suspension and distribution within the cell. Consistent trends were found when these effectiveness criteria were considered against relative impeller speed, in terms of percentage of critical impeller speed, N/Njs. Off-bottom solids suspension is complete at or above 100 per cent of Njs, with significant sedimentation occurring as the impeller speed drops below 60 per cent of Njs. Suspension heights consistently reached a level equivalent to 90 per cent of the tank diameter at the critical impeller speed, and dropped off significantly as N/Njs dropped below 60 per cent. The variation in the solids concentrations within the sampled profiles showed consistent trends in two-phase but not under three-phase conditions. The paper concludes that the critical impeller speed, Njs, commonly used in the design and operation of standard stirred tanks, is a very useful solids suspension benchmark for describing all aspects of solids suspension in mechanical flotation cells and should be correlated to system conditions.

Jan 1, 2005