Search Documents

By Penrose E. K

With the exception of occasional periods, when up to 80% of oxidized ore was treated, the G.M.K. plant treated all sulphide ore until October, 1939. The treatment was, briefly, as follows:The ore was ground to approximately 17% plus 200 mesh Tyler and agitated in cyanide solution, after straking. After agitation, the pulp passed through two stages of counter-current decantation washing in Dorr thickeners and was filtered once, to complete the precyanidation stage.The precyanide filter cake was repulped with flotation circuit solution and floated in a Denver Sub A flotation machine, consisting of twelve cells. The concentrates were roasted, cyanided and filtered four times before disposal to the' dam. The flotation tailings were thickened to conserve water and pumped away to a separate dam.The average results of flotation operations for the six months before October, 1939, are shown in Table 1.

Jan 1, 1942

The commonly used Stopes-Heerlen coal petrographic classification and nomenclature has over the years been subject to variable interpretations. This paper discusses the problem with specific reference to the inertinite maceral group. The effect of various interpretations of the Stopes-Heerlen system on maceral analysis is discussed and illustrated by means of comparative analyses conducted by a number of laboratories in Australia.An attempt is made to define the reflectance thresholds used by the authors to subdivide the inertinite group; the genetic and technological significance of these thresholds are compared.The difficulties of distinguishing structured and nonstructured macerals of the inertinite group are discussed in terms of possible improvements to the present StopesHeerlen system by extending the classification to include transitional maceral types.

Jan 1, 1970

The El Pe±on gold-silver deposit comprises four epithermal, low-sulfidation veins, which contain 2.9 million oz Au and 48 million oz Ag. Provisional data on alteration mineralogy, fluid inclusions, and vein textures constrain the chemistry and hydrology of the hydrothermal system responsible for ore mineralisation at El Pe±on. Alteration minerals include quartz, adularia, albite, illite, smectite, calcite, chlorite, and pyrite. Alteration minerals suggest the existence of near neutral pH, low salinity hydrothermal fluids, which circulated over an area greater than 18 km2. Complex mineral zonation patterns result from variations in host rock permeability and composition, overprinting alteration possibly produced by thermal waters from surficial and peripheral parts of the hydrothermal system, and supergene weathering in the hyperarid environment. Upflow zones were focused along N-S and NE trending structures, producing crustiform quartz-adularia+carbonate veins. Fluid inclusion data indicate vein deposition from low salinity (

Jan 1, 2002

The history of the industry which recovers rutile and zircon from the heavy mineral beach sand deposits of Eastern Australia began with the initial discovery of zircon in 1895. Whereas a large number of small companies operated during the rutile boom of 1955-57, the industry is now controlled by a few large groups.Mining is mainly by suction dredging. Metallurgical practice is a two-stage process in which a bulk concentrate of heavy minerals, recovered by gravity methods, is separated into its constituent minerals by processes based mainly on surface, electrical, and magnetic properties.Various separating devices using these principles have been developed in the industry and combined in various ways in the operating plants.There is scope for future metallurgical developments.INTRODUCTIONThe existence of deposits of heavy minerals ("black sands") on the northern coast of New South Wales has been known for at least 90 years. The earliest metallurgical operations aimed at the recovery of gold, platinum, tin and monazite. Mainly because of the low grade of these deposits with respect to these minerals, but also due to metallurgical difficulties, such operations were abandoned by about 1895 (Whitworth, 1959). The presence of zircon was recorded quite early (Carne, 1895) but Raggatt (1925) appears to have been the first to report the presence of rutile.The economic exploitation of the deposits was initiated in 1928 when D. H. Newland, State Geologist of New York, made an examination on behalf of The Titanium Alloy Manufacturing Company of America. Developments were then delayed by the world-wide depression, and the first commercial separation of the heavy minerals was made at Byron Bay in 1934 by Zircon Rutile Ltd. using a froth...

Jan 1, 1963

The mining industry in Australia frequently uses the services of specialist engineering and managing contractors and consultants for a majority of the work required for project development, from feasibility studies to project commissioning. The project owner's prime objectives are to achieve predictability and competitive advantage for their project. As the majority of this work will be carried out by contractors, the effective evaluation, selection and management of these contractors in the most appropriate forms of contracts is an essential ingredient to project success. The first stage to project development should be for the owner to examine its own resources to establish the role that it will fill and thereby identify the role and scope of contractors' involvement. Once the owner has developed this work plan, the selection of contractors and consultants should be structured to ensure that the owner acquires the appropriate expertise and experience to achieve its project objectives. The sequence of selection procedures is: 1. Pre-qualification of prospective contractors according to the owner's adopted criteria, through the use of a pre-qualification questionnaire. 2. Evaluation by the owner tender board according to predetermined mandatory criteria. 3. Preparation of tender documents for submission to qualified contractors. 4. Evaluation of tender submissions by the owner tender board using a pre-determined, weighted matrix of technical and commercial criteria. 5. Final selection and contract negotiation.

Jan 1, 1990

Particles of a complex nickel sulphide concentrate (containing pyrite, pyrrhotite, pentIandite, and violarite as the major mineralogical constituents) were entrained in a stream of hot gas the temperature of which was varied from 500 to -1000°C. Chemical analysis of the particulates collected from the furnace was used to detect the rapid change in sulphur content which accompanied the ignition temperature jump. X-ray diffraction analysis was used to characterize the oxidized material.These techniques showed that ignition was dependent on the mineralogical composition and occurred over the temperature range 500-900°C. Pyrite ignited first in the range 500-600°C; pyrrhotite was the least reactivemineral and required temperatures in excess of 800°C for ignition. The nickel minerals <pentIandite and violarite decomposed before ignition and ignited at temperatures intermediate to those required for the pyrite and pyrrhotite. The ignition temperature for the pyrite was found to be independent of particle size and concentration of oxygen in the atmosphere.Ignition temperatures determined by the simulated flash smelting method were compared with the results of differential thermal analysis (DTA) measurements performed on the same concentrate. Temperaturesdetermined in the DTA test as corresponding to the start of exothermic activity were shown to be at least 100°C below those determined by the simulation test.

Jan 1, 1978

The richer, shallower sapphire deposits of the New England region of New South Wales which have been traditionally mined by the small miner are almost worked out. Larger mining and exploration companies are replacing the small miner and exploring for the primary source of sapphire or lower grade alluvial deposits.   Although in recent years considerable exploration effort has been directed at locating the primary source, commercial exploitation of sapphire is still restricted to the working of alluvial deposits.   If the Australian industry is to compete against Asian and African producers it must use cost effective exploration, mining) processing and marketing methods.

Jan 1, 1990

By Tripathy A. K, Satapathy B. K, Nayak B, Mohanty J. N, Dey D. N

The paper deals with the metallographic tudy of heat treated chromite and chromite-coke composite briquettes. The briquettes, prepared from chromite concentrate of Orissa Mines using molasses-lime, dextrinelime and tamarind seed as binders, were subjected to different temperatures and examined metallographically. The change of phase with temperature was analysed by X-ray diffraction.

Jan 1, 1987

ignitions caused by cutting tools have occurred at a rate of some 14 per year in UK coal mines since 1965, mostly on the coalface. The rate has held steady despite reducing output and number of collieries. Investigations were carried out over this period into factors affecting both the concentration of firedamp in the cutting zone and the igniting source. A study into detecting and suppressing ignitions on shearers has been undertaken and it is feasible to prevent certain ignitions from spreading outside the cutting zone. Practical measures have been adopted by British Coal to identify frictional ignition sites and to lay down working procedures to minimise risk.

Jan 1, 1988

Studies of the Main Seam in the Rapahoe Sector of Greymouth Coalfield have shown that the proportions of palynomorphs and palynomorph groups vary vertically within the seam, but remain laterally consistent. Subsequent examinations of other seams in the Rapahoe Sector have demonstrated that the changes in palynomorph proportions observed in the Main Seam are specific to that seam, effectively providing a seam 'fingerprint'. Such a characteristic signature may be used to identify the Main Seam where faulting or seam splitting confuses seam correlation between drillhole intersections. Palynomorph assemblages are derived from the original plants which formed the peat mire, and yield information on mire conditions such as climate, mineral matter input and chemistry. These depositional factors influence coal properties such as mineral content, volatile matter yields and coal breakability. Palynological data can therefore assist in development of depositional lTIodels for prediction of coal quality variations. Several other, thiner seams in the Rapahoe Sector have been demonstrated to also contain recognisable palynomorph assemblages, suggesting that other seams may also possess distinct palynomorph abundance profiles.

Jan 1, 1996

By P. S. B. STEWART

As part of a continuing study of mechanisms of breakage, the grinding at Nairne Pyrites Pty. Ltd. was traced by the addition of barytes and the results compared with parallel small scale laboratory tests. It was confirmed that the same basic mathematical functions described the behaviour of the full scale ball mill as those established in the small scale mill. However, an additional classification function was required to define the behaviour for the rod mill and was evaluated as a function of size from the experimental data. The classification and grinding of the pyrites ore was assessed from steady state size distributions around the circuit.

Jan 1, 1971

Experimental results are presented for the anode overvoltage as a function of current density for different alumina concentrations in an alumina reduction cell. Voltage changes due to the electrolyte resistance and also the decomposition voltage, have been evaluated as a function of alumina concentration and anode current density. From these values of voltage, changes in the total cell voltage have been derived for changes in alumina concentration for different anode current densities. The results show that for each operating current density there exists a discrete alumina concentration that defines a minimum reduction cell voltage. Discussion is made about potential savings in power consumption when the alumina concentration is controlled.INTRODUCTIONThe standard procedure in the aluminium industry when analysing the cell-voltage required for the Hall-Heroult process for reduction of alumina, is to subdivide the total voltage into the following components (e.g. Pearson, 1955; Maritell, 1960).1. ohmic drop through busbars and joints2. ohmic drop through cathode lining3. ohmic drop through anode4. ohmic drop through electrolyte5. overvoltage at anode6. electrolytic decomposition voltage.(Overvoltages ,at the cathode are of negligible magnitude at all practical current densities.)It is understandable that the voltages assigned for each factor invariably differ for different workers...

Jan 1, 1965

In most mines using presplitting the final excavated wall shows a zone of damage just below the crest and well defined presplit half barrels. The crest damage (surface dilation) zone varies and is added to by subsequent adjacent perimeter blasting operations. Keeping the preconditioning to a minimum is possible using the methods described in this paper, developed on several diverse and geographically distant mining operations to control crest dilation and preconditioning by presplitting in advance - not just laterally but vertically in advance. The first documented case (Delbridge, Marton and McSweeney, 2004) in the development of the concept was undertaken at AngloGold Australia Pty Ltd's Sunrise Dam Gold Mine (SDGM), located beside Lake Carey, some 730 km northeast of Perth, Western Australia. The mine had been developed in a series of cutbacks to a depth of over 300 m and began underground mining during the latter stages of open cut operations. This mine is fairly unique in that it utilised a single pass vertical presplit which initially extended over three bench heights and after the failure mechanisms were understood, over four benches. The presplit drilling for the three stacked benches started on the floor of the second bench so that any dilation was confined to the surface one bench above the crest and modified perimeter blasting was then developed to curtail damage from blasting adjacent to the new crest. The second case is based on a South African coal mine in the Witbank Coal Measures, 140 km northeast of Johannesburg, Republic of South Africa (RSA). It was important that blasting for optimal wall stability and minimal scaling was developed in advance. A dragline is scheduled to excavate the #2 seam midburden which is the lowest of the economically viable coal seams in the five seam Witbank Coal Measures. Mining of the overburden, coal and partings above the dragline midburden pass are by excavator and truck and each mining layer is individually blasted. The results of presplitting the midburden through the overlying coal seams and partings have provided a presplit with no surface dilation of the midburden crest and ensures any subsequent crest loss is solely due to blasting adjacent to the vertical presplit. Typical of all coal mines in South Africa only vertical presplits are used. Wall control is most commonly delivered by presplit blasting and one common sight after the dust clears is a ridge of broken blocks along the presplit row, usually with a main crack running between the presplit blastholes and often parallel cracks either side of the perimeter line. The surface rock strata or block structures have been dilated by the venting gases and shock waves. Decoupled, fully coupled, single or double deck charges are used depending on a variety of factors, anecdotal practices and perceived benefits. Preconditioning of the crest rock by blasting from above may not be visible to the naked eye (or non-existent in overburden in strip coal mines) but the high speed venting of explosives gases (and often the water in the presplits) preferentially follow existing cracks and structures because there is no developed presplit crack near the surface. This nearly always lifts, shifts and separates the surface structures and geological layers. Stopping the dilation by 'sacrificial' or 'in advance' presplitting has been shown to reduce the crest loss at both metal and coal mines. Drilling and presplit blasting through an upper level of bench or layer provides a degree of restraint to the target layer where the crest must be maintained and any damage caused by the venting gases will not cause concern as it is removed as planned, leaving a stable crest.

May 1, 2010

Neutralization with lime is a simple, cheap, and effective means of treating acid raffinates from uranium processing to' raise the pH, reduce the concentrations of dissolved salts (including heavy metal impurities), and remove amine by adsorption. Two-stage neutralization, using limestone in the first stage at approximately pH 4 and lime in the second, lIlay be advantageous.Lime neutralization of mffinates in the pH range 7 to 8· 5 generally reduced the radium ·concentration to 10 to 200 pCi 1-1, but ·there was considerable scatter in the experimental data. The radium concentration was further reduced to less than 3 pCi 1-1 by co-precipitation of barium (radium) sulphate with 10 mg Ba (as barium chloride) per litre of raffinate. Adsorption of radium on barytes was -also effective in reducing the radium concentration in neutralized raffinate to less than 3 pCi 1-1.The radium concentration of pit water was readily reduced to less than 3 pCi 1-1 when pit water containing 0·01 M sulphate as ammonium, calcium, or sodium sulphate was treated with 20 mg Ba per litre of pit water.Adsorption on barytes was also effective in removing radium from pit water containing 0·03 M sulphate.

Jan 1, 1975

By Bohrn W, Milionis K, Tessmer G, Reidetschlager J

The share of electric arc furnace based steel production is increasing - New technologies for the production of virgin raw materials for EAF production are under development and on the market - VAI has a strong position in the field of scrap substitution technologies with their COREX«-, COREX«-DR and FINMET«-technology. In late-1998 the steel plant SALDANHA was started up successfully. This integrated compact mill is using the COREX«-technology as hot metal and a combined DR-plant as DRI production unit. Also in 1999 the BHB FINMET« plant Port Headland went on Stream.

Jan 1, 1999

Despite the recovery of approximately six million ounces of alluvial gold from the West Coast of the South Island, New Zealand during the last 140 years, a great deal of this having been obtained via sluice boxes and riffle tables, there has been little advance in riffle table technology during this period. In this paper contemporary riffle table design and current operational practices are examined. Studies of gold loss to undersize tailings are described. In addition recommendations derived from recent research carried out in North America are contrasted with gold saving strategies adopted by West Coast miners.

Jan 1, 1992

By Sheng-Hui X

This paper introduces a new coal-based rotary kiln process of DRI production - the CRIMM process, which is developed by Changsha Research Institute of Mining and Metallurgy in the past years. Its main features are the use of composite pellets (in rotary kiln). The process consists of preparation of pellets from iron concentrate and coating of coal on their surfaces. The new process is able to overcome a series of defects of the conventional coal-based rotary kiln processes. A continuous test was conducted using an experiment rotary kiln (-0.6;, x 3 m). TFe of the magnetic iron concentrate used in the test is 67.25 per cent. TFe of the product DRI is 88.54 per cent, MFe is 84.11 per cent, S and P are less than 0.02 per cent. The metallisation ratio of pellet is 95 per cent. The pellet power ratio is less than 0.3 per cent. The utilisation coefficient of rotary kiln is 1.3 t/m'-d. The overall recovery of iron concentrates is 99.7 per cent. Two small industrial plants using the CRIMM process are being set up in China. Their coal consumption can be decreased to 520 kg standard coal per ton DRI respectively.

Jan 1, 1999

The district specially referred to in this paper comprises the very gently sloping country extending from the western shores of Port Phillip from the mouth of the Yarra to Footscray along the Bacchus Marsh railway to near that town thence in a southerly direction to the Little River, and along that river to the coast, 1 as may be seen on the accompanying map. Almost the whole of this area is covered by volcanic rocks, consisting of pumerous sheets of basalt, which have been poured out of various volcanic hills in the districts, such as Mts. Atkinson and Cotteril, near Melton; Mt. Maryand Bald Hill, 12 and 16 miles respectively N.W. of Werribee; and vents in different parts of the parishes of Tarneit, Mouyong, Mooradoranook, Pyweitjorrk, and Derrimut. These volcanoes were in an active state of eruption during a late period of the earth's historyprobably the late Pliocenll, or still younger Pleistocene.Occupying a narrow strip of country, for most of the distance along the coast from Williamstown to past the mouth of the Little River, there occur deposits of still younger age, belonging to the Recent period. These lie on the basalt, and extend for distances varying from a few chains to more than a mile back from the beach. They comprise superficial deposits of blown sand, and raised beaches, composed of marine sands...

Jan 1, 1902

By M I. Pownceby, N A. S Webster, R Pattel, N Ware

The decrease in quality of Australian iron ore, coupled with the demand for more efficient energy use, necessitates closer monitoring and optimisation of process conditions for iron ore sinter production. Sinter properties are correlated with the mineralogical content and traditionally, quality control has relied on methods such as Fe2+ determination, point counting via optical microscopy and automated electron beam techniques such as QEMSCAN; these can have a typical turnaround time of several days between sampling and reporting of results. As well, there is additional uncertainty around quantifying some of the complex mineralogical phases in sinter such as silico-ferrite of calcium and aluminium (SFCA) and SFCA-I, which are key phases influencing sinter quality. There is a clear need for the implementation of alternative analytical methodologies that offer a turnaround in hours or even minutes to provide information to accurately maintain production conditions.X-ray diffraction (XRD) is a technique widely used for the quantitative mineralogical phase analysis (QPA) of ores and processed materials in the iron ore industry. Partial least squares regression (PLSR) analysis methods have recently been suggested as an indicator of sinter Fe2+ content from powder XRD data without the need for rigorous and often time-consuming mineralogical analysis by the operator. In this study we provide results from the implementation of PLSR to predict the strength of iron ore sinter. Results are sourced from a well-constrained data set comprising strength properties (as quantified by a tumble index (TI)) from a series of compact laboratory test samples. Using this data set it was determined that PLSR has potential to be used as a method for calculation of sinter TI from powder XRD data and, therefore, process control.CITATION:Webster, N A S, Pownceby, M I, Ware, N and Pattel, R, 2017. Predicting iron ore sinter strength through X-ray diffraction analysis, in Proceedings Iron Ore 2017, pp 331–334 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

Open cut mining of the Black Rock chalcocite ore started in 1963. A ground movement monitoring programme was commencing in the early stages of mining when signs of instabilityof the western wall became apparent. Eventually 100.000 cu vd, of overburden Were removed beyond the rim of the western wall in an attempt to stabilize the slope. Subsequent decpenlug and mining till the final batter angle of 45 resulted in deterioration and mining was stopped 38 ft short in the ulltimte design deplh of 520 ft.Investigations showed that the geology of the western wall , was a major factor in the instability of this wall. A block jointed model was made 10 illustrate some of the pehomena observed. Quallatative agreement was found between the model deformation and the field measurements obtained.The results of the monitoring programme clearly show the value of this work In respect to the conlrol of the mining operatIon...

Jan 1, 1968