Search Documents

By R-H Yoon

Increasing the upper particle size limit of flotation would allow operators to increase mill throughput, save operating costs, simplify flow sheets, and increase rate of return. However, coarse particle flotation is difficult for various reasons, of which bubble-particle detachment has been identified as the major limiting factor. In the present work, the process of bubble-particle detachment has been studied by directly measuring the forces required to detach air bubbles from hydrophobic solids. The measurements were conducted using a hanging balance apparatus. The measured forces were converted to detachment energies that can be compared with the work of adhesion, which in turn is a function of hydrophobicity, surface tension and contact area. The results were converted to detachment energies using the Young-Laplace equation for capillarity. In the present work, the solid surfaces were hydrophobised by coating them with octadecyltrichlorosilane and cetyltrimethylammonium bromide. The results show that bubble-particle detachment occurs in two steps. In the first step, air bubbles are deformed, while the three-phase contact (TPC) line is pinned, until contact angle reaches advancing angle. In the second step, the TPC line moves along the surface until solid/air interface is replaced by solid-liquid interface. In general, the energies of detachment measured in the second step are in good agreement with calculated work of adhesion. Thus, the energy required during the first step effectively represents an energy barrier for bubble-particle detachment. It has been found that the energy barrier varies with surface roughness and surface tension. The results of the present investigation suggest, therefore, that coarse particle flotation can be improved by control of particle hydrophobicity, surface roughness, and surface tension.

Jan 1, 2005

Longwall mining has historically been considered an application for only deep reserves. This has changed in the recent past as longwall has become competitive with surface mining. Many resources marked for stripping now he in the domain of longwall. Today, the best longwall mines compete with strip mines operating in even the lowest stripping ratios. Longwall mining has become more widely applicable than it ever has been in the past and it is now generally considered the method of choice in situations where high levels of coal production are required. But the best way to use longwall mining has become less certain with the opportunities that highwall access provides. Wall-to-wall mining is the use of retreating longwall developed from and retreating toward a highwall. As a surface mine reaches its ultimate highwall, the opportunity for longwall punch mining or wall-to-wall mining is obvious. There are several clear operating advantages to operating a longwall in this way and where highwalls are available, the best economic decision will generally favor planning a direct approach. Yet wall-to-wall is not applicable in every situation even when highwalls are available. Moreover, the advantages of wall-to-wall mining do not always justify the cost of trenching or box cuts to access coal . However, many tactical advantages of operating from the highwall can be realized with the use of specially equipped blind drilled or raised bored shafts. This paper discusses novel techniques for a shaft assisted mining system which permits the addition of conveyor structure and mine systems from the surface to the face for advance and retreat mining with longwall, shortwall or room and pillar panels.

Jan 1, 1998

By H Rouhullahi, E B. Veshki an, R Kottnauer

The Galandrud coalfield is located approximately 20 km south from the coast of the Caspian Sea, Ruyan town, on the north slopes of the Alborz mountain range, in the elevation between 500 m (the Galand River valley) and 1350 m. For the time being, 32 coal seams (generally of small thickness û 0.8 m on average) have been recognised within the. On the other hand 72 coal banks of balanced properties have been included in reserve calculation, which means that some of the seams consist of several banks. The general dip of strata belonging to the south limb is about 30¦ to the South (with drags close to the south overthrust, where the dip reaches 85¦), while the dip of beds at the north limb is rather steep and usually between 45 to 75¦ to the North. The coal quality is in a rank of high volatile bituminous coal. The steep dip, unstable lithological development, complicated tectonics and comparatively lower coal seam thickness are the characteristic features of the Galandrud deposit. Environmental protection of this area makes exploration and exploitation more complicated. During mine exploration several adits were driven at three levels with 50 m vertical distances. About 4000 m of gates and crosscuts were up to now driven. During mining test the down-cut mining method (with one cut), the strike cut mining method and the down-cut mining method with two cuts were tested. The paper describes outlines for the selection of mining methods on the base of classification of the effective hangingwalls and footwalls, hazards of mining operations, and possibilities of the mechanised mining.

Jan 1, 2003

Parallel lenticular orebodies occurring at the C.S.A. mine of Cobar Mines Pty. Ltd. are mined by mechanized cut and fill stoping over the full strike length. Access is provided for each stope lift from an inclined drive adjacent to the orebody. Mobile drill jumbos mounting hydraulically-operated booms are used for drilling upholes which are subsequently charged with ANFO explosive.Close control of drilling has been found essential for good back conditions and to ensure optimum fragmentation.Broken ore is transported from the face to the main ore pass by rubber-tyred, diesel-powered, load-haul-dump units. Initially, the units trammed ore to the main pass via the incline drive. As the stopes advanced and the lead distances increased, stope passes were developed in the wall rock and raised concurrently with each stoping lift. The passes terminate in drawpoints and production loaders are used to transport ore from the drawpoints to the main ore pass system.Two parallel ore pass systems have been developed to cater for both copper and copper-zinc ores. These systems terminate above a 48 in. by 60 in. jaw crusher. The crushed ore is conveyed to a traversing rock box and thence to one of two crushed ore bins adjacent to the main hoisting shaft. A loading station conveyor is interlocked with the winder to provide automatic ore hoisting.All phases of ore handling have been mechanized as completely as possible. Results to date indicate this policy has been vindicated but highlight the need for tight operating control and close liaison between operating and maintenance personnel.

Jan 1, 1969

By L E. Setiawan

The mining and milling groups at Batu Hijau are tasked with increasing SAG mill throughput by approximately ten per cent. Avenues used for this process are blasting and crushing optimisation, ore blending and predicting SAG mill throughput in relation to the geological model. This is in line with traditional æMine to MillÆ studies. At Batu Hijau, mill and mine sequencing cannot readily be configured to perform the surveys traditionally required by a æMine to MillÆ study while meeting the daily production target of 140 000 tonnes per day and processing from varying ore types in one pit. A program called BOCCOST (blasting optimisation crushing conveying optimising SAG throughput) has been implemented to capture approximately 200 variables from blasting, mining and milling operations and assign them to a common point in space in the geological model in real time. Interpretive analysis of data from BOCCOST is used to model relationships between the 200 variables to determine which and how these factors affect SAG throughput. Once these relationships are determined, the blasting, ore blending and crushing process can be optimised to generate a product that maximises mill throughput. The relationships modelled from BOCCOST are also used to generate a SAG mill throughput estimator, which can be coded into the production block model. The block model can be reconciled with the geological block model for correlation by geological domain. Once this relationship is established, SAG mill throughput domains can then be established for predicting SAG mill throughput. This SAG mill throughput estimator is then used in conjunction with revenue calculations to determine an ore cut-off, which combines these two elements to maximise metal production.

Jan 1, 2002

To the south and west of Broken Hill lies the Thackaringa silver-lead district, about 25 miles, and is the locality really of the first silver find in the country long before Broken Hill, the geological fomations of which it much resembles. The Iocks and their structure are identical, except that in this area they are  more irregularly foliated and apparently much more faulted and expose in places quick successions of complete anticlines and synclines, even in a single lease. Saddles of ore respectively are found coinciding with the flexures of the rock but many minor veins otherwise and branches exist and make connections which render the whole a mining problem. It follows then that the surface.of the ground after some denudation in dotted with croppings of all the series, and in such a confusing way that the actual strike of a vein may be even confounded with the dip and readily mistaken for it at a few places. The main character of the outcrops are those usual in the district consisting almost wholly of argentiferous and silicious ironstone, sometimes gossan, which at a depth in a few feet changes to a gangue of very silicious carbonate of iron (crystallised), which occurrence is uniform through this district.The exploration of the lodes has not been extensive as it has not been well understood. Shallow shafts and drives have comprised nearly all the mining at present, which is evident on first sight by the numerous shafts and small excavations dotted 'about, as in an alluvial field. The depth of exploration underground in one place had gone several hundreds of feet, never more than 150 feet vertical from the surface in depth and irregular. The undulations of the most continuous work in this direction is such that it presents at different places successively either a tunnel, shaft, underlay winze, level, or Tise, and is on ore all the time, and where the rocks are faulted (which occurs as much as 30 feet and more) these changes are very abrupt, but for working on are suitably connected by the management.

By A M. Robertson, R Lefebvre

Air movement and associated oxygen transport through waste rock dumps has the potential to significantly enhance the rate of oxidation of pyrite-bearing material. While this is a desired outcome for most heap leach operations, airflow in waste rock storage facilities can result in significant increases in generation and acceleration of acid rock drainage. Hence, a good understanding of internal airflow through waste rock dumps is required to control ARD and minimise any associated liability. The principal mechanisms contributing to airflow and oxygen transport in a waste rock pile include: diffusion; advection due to a thermal gradient (chimney effect) and/or wind pressure gradients; and advection due to barometric pumping. While diffusion is typically limited to a near-surface zone of a few meters depth, advection and barometric pumping have the potential to move air (and oxygen) to much greater depths into the pile. In general, the more permeable the waste rock material, and the greater the height-to-width ratio of the waste rock pile, the greater is the potential for advective air movement. The reactivity of the waste rock material as well as the coarseness (hence air permeability), and the spatial variability of these properties within a pile, have a strong influence on the magnitude of thermally induced advection. In contrast, air movement due to barometric pumping is controlled by the waste rock porosity, changes in ambient air pressure and the heterogeneity of air permeability of the waste rock dump. Results of field monitoring and numerical modelling using TOUGH AMD are presented to illustrate the concepts on air movement in waste rock piles discussed in this paper. During the design and construction phase, airflow can be controlled by judicious placement of reactive waste rock and use of selective placement techniques to control the internal structure of the waste rock facility (eg introduction of horizontal layering, prevention of inclined, high-permeability, channels (æchimneysÆ)). Several closure measures are available to minimise airflow including: placement of a low-permeability cover to reduce air entry; and placement of a non-reactive cover material to isolate reactive material from the zone of active airflow and/or regrading of the waste rock pile to obtain a geometry and internal structure less susceptible to advective airflow.

Jan 1, 2003

In Australia a social impact assessment (SIA) is generally required prior to the approval of a mineral resource extraction or processing projects as a part of the Environmental Impact Assessment (EIA) process. In recent years there has been increased attention on the adequacy of the SIA process applied in major project assessment. Most applications have focused on the impact identification process with little attempt given to the community negotiating power over how impacts will be addressed. The impact assessment tends to occur at a single point in time, with no subsequent re-evaluation or ongoing social impact management and monitoring process. The assessments rarely specify how responsibilities for impacts on communities may be apportioned between project proponents and government, and have been inadequate in dealing with cumulative project impacts. In Queensland, concern about these shortfalls have led to the release of the Sustainable Resource Communities Policy 2008 and requirements for social impact management plans (SIMP) to be developed for each resource development in the State. In this paper a 'pressure-state-response' approach to impact assessment is used to develop an 'impact-response-monitoring-evaluation' (IRME) framework that can be applied to ongoing evaluation and monitoring of social impacts. The framework is applied to coal resource developments in the northern Bowen Basin in Queensland to identify core requirements in a SIMP. The IRME framework is flexible enough to be implemented at various spatial and time scales, for the wellbeing of the local and regional mining and non-mining communities in Australia. The framework can be further examined in other mine developments and could be integrated with the existing mining or environmental protection acts.

Jun 1, 2010

By Moyes A. J

The Intec Copper Process uses a strong chloride electrolyte at atmospheric pressure and 80 - 85¦C to produce high purity, 99.99 per cent copper granules and elemental sulphur. A recent, exhaustive study by an independent, major Australian corporation has shown the capital cost of an Inter plant to be approximately half that of a copper smelter at the 200 000 tpa capacity level and approximately half the operating and capital cost at the 50 000 tpa level. The Inter process costs were also shown to be greatly superior to the best available leach/SX/electrowin technology. The process utilises a multi-stage counter current leach at 80 - 85¦C with the addition of air at atmospheric pressure to precipitate iron as a goethite type compound, followed by a two-stage purification process separating impurities in metallic- and other forms. Purified cuprous chloride/sodium chloride solution is fed to an electrolytic diaphragm cell where high purity copper granules are produced at current densities of 1000 - 1500 A/m2 withoutthe need for conventional electrode stripping. Power consumption is approximately half that of the cupric route. The product is suitable for the direct powder metallurgical conversion of the granules to products such as wire or strip. All the steps in the 'furnace free' conversion of copper mineral to product have been demonstrated The process can treat low grade and contaminated concentrates without penalty, thereby offering greater returns to the miner. Lead, zinc and silver may be recovered as metals, with the high oxidation potential of the electrolyte allowing extraction of gold at high efficiency. The gold is selectively precipitated on activated carbon with negligible copper and silver contamination.

Jan 1, 1992

By P K. M Mazzoni, D Frantois-Bong

This paper aims to show alternatives to the estimation methods used for finding the parameters in GyÆs well known model for sampling variance in the case of particulate materials. Many experiments designed for gathering data on the sampling variance for specific mineral deposits allow the experimenter to use approximations in the calculation of the parameters of the mathematical model involved, which sometimes can be very useful. However, there are some instances where approximations lead to biased estimates of the parameters, and consequently, lead to errors in the establishment of the sampling protocol and treatment of quality control data. In the present work, an alternative is presented for computing the parameter values based in any experimental set up, without the need for any simplification. The method was derived using the method of least squares and evaluations are made using the usual tools in this kind of methodology: residual analysis and evaluation of the fit by means of a plot of calculated versus experimental variances. With the aid of these tools, one can better evaluate the structure of the experimental errors in such applications, and the adherence to the proposed model. In addition, it is possible to perform hypothesis testing for the equality of different sampling procedures in terms of sampling variance. The full mathematical details are given, together with an algorithm for applying the method, which can be implemented easily using any computer language. An illustration of the method is shown, considering the international work done in ISO/TC 102. This example is a determination of the minimum sample mass to be collected in iron ore shipments, in order to achieve a specified sampling precision.

Jan 1, 2005

By Kennedy JT

This is a question that will be asked many times and by many individuals during the various evaluation stages of any new project. However, the question itself will often have different connotations to the different groups invariably involved in such an exercise. As examples, consider just three of the several different groups involved in the development of a new mining project - Financiers, Consulting Engineers and the Sponsors of the project (potential borrowers). To the Financiers, a 'bankable project' will be one against which they will be prepared to lend funds (but not necessarily all of the funds requested by the Sponsors). This usually means that in the first instance the technical information presented to the bank has satisfactorily covered all of the requisite areas to the levels of accuracy required. More importantly, the financial evaluation of the projected economic performance of the mine, as a whole, is considered sound and a set of arrangements under which the bank is prepared to advance loan funds have been structured which fully satisfy the bank's credit criteria. To Consulting Engineers preparing a feasibility study (or a part thereof), on behalf of the project Sponsors, the term 'bankable' invariably only refers to the technical completeness and the level of detail contained in the report which they are preparing. Their scope of work will not necessarily have been broad enough to fully satisfy a bank's requirements. It is unusual to see any specific references to overall project viability or profitability in Consulting Engineers' feasibility reports, other than those which are automatically associated with the use of the term 'ore'.

Jan 1, 1990

A process was developed based on the thermal hydrolysis and precipitation of iron from solutions resulting from the leaching of zinc plant residue. A study was made of the hydrolysis of iron, at temperatures in the range 140-220°C, in both pure solutions of ferrie sulphate and in leach solutions derived from plant spent electrolyte.At 200°C hydrolysis of pure ferric sulphate solutions results in the precipitation of ferric oxide, Fe2O3, at low acid. concentrations, and a basic salt, Fe2O3.2S03.H20, at hIgher acid concentrations. At 180°C ferric oxide is precipitated at low acid concentrations, but at higher acidities. carphosiderite, 3Fe203.4SO.3.9H20, is the stable phase. Frequently a mIxture of ferric oxide and carphosldente IS produced at 180°C, the ratio of phases being dependent on the non-equilibrium experimental conditions.With solutions derived from plant spent electrolyte hydrolysIS at elevated temperatures results in the precipitation of jarosite compounds of the type NaFe3(S04)2(OH)6 The precipitation of natrojarosite jarosite, and ammonio-jarosite was studied in detail. Temperature, free acidity, and the concentration of sodium potassium, and ammonium ions are critical factors which affect the extent of precipitation.A process based on ammonio-jarosite precipitation was tested in a pilot plant.An alternative method of iron removal based on the addition of zinc oxide calcine, to neutralize excess acidity, and the precipitation of ferric oxide was also tested in the pilot plant. Both processes appear economically favourable...

Jan 1, 1967

An Investigation on the Effect of Chrysotile Particle Shape and Anisotropic Properites on the Rheology of Chrysotile Suspensions Chrysotile, a polymorph of serpentine, is a phyllosilicate mineral that occurs as a major gangue mineral in many ores (eg Mt Keith nickel sulfide ore, Western Australia). The rheological behaviour of chrysotile stems from two main factors: its distinctive morphology and its electrical surface charge. It is believed that these factors are central to the problematic rheological behaviour and low solids throughput typically experienced in the processing of such ores. In this work, a study of the effects of chrysotile surface charge properties and particle shape on the rheology of chrysotile suspensions was conducted. It was found that the rheology of suspensions of pure chrysotile is characterised by extremely high yield stress values over a broad pH range (pH 4 to 11).The disparity in the point of zero charge and range of maximum yield stress for chrysotile is consistent with the anisotropic nature of chrysotile particles. A comparison of the rheological behaviour of quartz suspensions (non-fibrous) to that of chrysotile suspensions (fibrous) provides a practical indication of the effects of the fibrous nature of chrysotile relative to non-fibrous minerals. The long, thin fibres are easily entangled to form suspensions with much higher plastic viscosities and Bingham yield stresses than non-fibrous particles. Chrysotile particle shape and surface charge are central to the rheology of chrysotile suspensions, although shape appears to play a more significant role in this regard. This fundamental study would be beneficial to the ongoing research for improved recovery in the Mt Keith nickel sulfide ore as well as other chrysotile bearing ores.

Sep 13, 2010

THERE is available a considerable amount of literature concerning the practice, and, to a smaller extent, the theory of ventilation as it applies to coal mines. Publications considering the subject of ventilation of metal mines from a practical viewpoint are much less numerous, whilst the treatment of the theoretical aspect of the question (except in so far as is common to coal mining) appears to have been almost neglected. This may be due to one of two causes (a) That in many metal mines (especially those which have not attained a great depth), on account of the greater number of connections with the surface, as compared with coal mines, natural ventilation has sufficed.(b) That in metal mines where the foregoing is not the case the solution of the ventilation problem from theoretical considerations has been regarded as involving so many complications that any attempt at the determination of a set of concrete ventilation figures applying to and throughout the mine would be futile. Whilst it is freely admitted that the difficulties inherent in the application of theory to the ventilation of metal mines are numerous, it must also be admitted that few attempts have been made to overcome them. The ultimate aim, of course, would be the collection of sufficient data to enable the probable behaviour of the air-currents throughout the whole of the workings of any mine to be accurately predicted under any particular set of circumstances. Failing the attainment of this goal of perfection, it would at least appear that much valuable information might be obtained. In ventilation, as in...

Jan 1, 1921

By Iley J. D

The production of zinc from low grade concentrates, particularly those high in iron, has a poor economic return due to a combination of higher concentrate transport costs, increased processing costs and an increased cost for disposal of iron residues. The production of iron-bearing residues from the electrolytic zinc process is also seen as undesirable for both cost and environmental reasons. This paper details the pilot plant testwork conducted at the Pasminco Research Centre in conjunction with Minproc for the production of zinc oxide fume from a high-iron zinc sulphide concentrate from Colquiri in Bolivia. The concentrate is derived from a tailings retreatment operation and has a high iron content (40 - 45 per cent Zn, 14 - 17 per cent Fe) due to the presence of marmatite. Pilot plant trials were conducted using the slag bath reactor at Pasminco Research Centre at rates up to 500 kg/h of pelletised zinc concentrate, using a natural gas/oxygen-enriched air lance. The fume produced averaged 76 per cent Zn at recoveries up to 96 per cent and was recovered in a baghouse after gas cooling. The iron was oxidised into a fayalitic slag that passed the TCLP test (toxicity characteristic leaching procedure) and the sulphur was oxidised to produce a high SO2 gas which would be suitable for sulphuric acid production. The process produces a zinc oxide fume that can replace calcine as a feed for electrolytic zinc plants. The iron reports to a stable slag for disposal, thus eliminating the need for its disposal as jarosite from the leach plant. Only a simple leaching operation on the fume is required as there is no zinc ferrite present.

Jan 1, 1993

By Pollmans GJ, Hoberg H, Schneider FU

The Institute of Mineral Processing at Aachen University of Technology has been engaged in fine and ultrafine comminution for several years. Former investigations had been dealing with the mechanical activation with the aim of increasing the solubility of highly resistant oxides such as tantalite and niobite while research on the product of ultrafine powders is of major importance at the moment. Materials of that kind are of increasing interest in the production of extremely resistant ceramics, in the development of new raw materials, in powder metallurgy and in the production of fillers (extender pigments) and pigments. The creation of ultrafine powders is difficult and very expensive. They can be produced by means of condensation or dispersion methods. One important method of dispersion is mechanical comminution. Due to long and intensive research and development all over the world important advances have been achieved but still a great number of questions and problems occur especially in producing materials of submicron and nanometer grain sizes which could be answered or solved only insufficiently up to now. These mentioned difficulties refer especially to: ò the required energy input into the feed material, ò the forming of strong agglomerates and wall stickings, ò the required product qualities, and ò the entire and reliable characterisation of the products. Basic investigation aim to clarify the micro and macro processes of ultrafine grinding and work towards solutions to the difficulties mentioned above. The aim of the Institute's research is the development of a new grinding device for producing ultrafine powders. First results of a laboratory scale mill of that type will be presented in this paper.

Jan 1, 1993

Optimisation and sensitivity analysis of final pit limits is now an accepted procedure for open pit planning studies. Tools to assist the design engineer in an underground metalliferous mine to make optimal choices for the selection of major development, stope geometry and cut-off grade analysis have not been available. The engineer has had to rely on experience and a limited analysis of design alternatives. A new tool called the `floating stope' has been developed to define the optimal (boundary) limit for material that can be economically extracted by underground stoping methods. The method is analogous to the `floating cone' method of open pit optimisation. The geology and mineralisation are modelled as a regular or subcell block model. Included in the model are structural and geotechnical features, and any previously mined out areas. Inputs to the procedure include the minimum stope dimensions, cut-off grade, stope head grade, and the way in which dilution is to be calculated. The optimisation procedure can be directed to maximise ore tonnes, grade, contained metal or the economic (dollar) value of material mined. The procedure can be applied at each stage of mine evaluation and design to assist with preliminary resource appraisal, selection of stoping methods, and detailed mine design. As with open pit optimisation procedures, manual intervention by an experienced engineer is required to produce practical and detailed designs. This practical design should follow the optimised design as closely as possible. The paper outlines the algorithms used in the definition of the stope envelope, and describes the analysis and results of several case studies where the optimisation procedure has been applied.

Jan 1, 1995

By Yu AB, Azahari HL

Indonesia has the largest coal reserves in the south-east Asian region. According to estimates from the World Energy Confer- ence, it has reserves of 18 billion mt lignite, 4.4 billion mt sub-bituminous coal and 774 million mt bituminous coal (Wyllie,1988). In recent years, substitution of coal for oil in power plants has been the goal of the Indonesian government since proven deposits of coal are about five times as large as national hydrocarbon reserves and most of Indonesia's power stations are still oil fired. Recently a coal fired power plant has been built in Java Barat, which will have a full capacity of about 3000 MW. It is intended to supply coal for this power plant from Bukit Asam mining area (South Sumatra). Coals from Bukit Asam - which are of the lignite or brown coal type - usually contain considerable moisture . It should be noted that reference to moisture in coal pertains to the total moisture content. This is comprised of what is commonly termed as equilibrium moisture and surface moisture. Surface moisture typically affects combustion process as well as pulveriser performance since it possibly influences the relative ease with which coal may be ground. In practice, the surface moisture produces agglomeration of the fines in the pulverising zone and reduces pulveriser drying capacity because of the inability to remove the fines as quickly as they are produced. This agglomeration has also the same effect as coarse coal during the combustion process because the surface area available for the chemical reaction is reduced, hence the combustion efficiency is also reduced. The influence of the moisture of some coals on their grindability (Hardgrove Grindability Index) has been previously correlated by several authors; some of them will be mentioned later. Those correlations, however, could not be immediately applied to any coal since it is still believed that there are other factors which influence the grindability of the coal, such as type and rank of the coal. The relationship between coal moisture content and its grindability has been investigated by Ellmann and Belter (1955). It was found that, for North Dakota lignites, the grindability varied as the moisture content changed. In Britain, Fitton, Hughes and Hurley (1957) stated that, for Bilsthorpe coal, over a wide range of free moisture content (from air-dried to about 30 per cent moisture), the Hardgrove Grindability Index (HGI) remains virtually unchanged. In addition to that, it was suggested that it would be slightly advantageous to dry the coal below its air-dried moisture content (at temperature ¦ 100¦C) to increase the ease with which coal could be ground, especially for low-volatile coal and high-volatile non-caking coal. Furthermore, it was also concluded that a broad relationship appeared between coal rank and Grindability.

Jan 1, 1993

By P Barrette

The manual gravimetric drying moisture determination methods currently employed by most mineral processing plants fail to provide timely and accurate information required for automatic control. The costs associated with transporting and handling concentrates represent a major portion of the overall treatment price. When considering the cash flow of a mining operation that is governed by both the smelter contract, with moisture penalties and the quantity and quality of the concentrates shipped, any tool that provides real-time feedback on the process is vital (Edwards, RP 1994). The introduction of an on-line moisture sensor would become a welcome addition to the process control field instrumentation package now applied. A novel on-line determination system for ore concentrate moisture content would replace the tedious manual procedure. Since the introduction of microelectronic-based control systems, operators have strived to reduce the treatment costs to the minimum. Therefore a representative and timely determination of on-line moisture content becomes vital for control set points and timely feedback. Reliable sensors have long been on the æwish listÆ of mineral processors since the problem has always been that you can only control what you can measure, (Konigsmann, 1990). Today, the task of moisture determination is still done by the classical technique of loss in weight utilising uncontrolled procedures. These same methods were introduced in the earliest base metal concentrators. Generally, it is acceptable to have ore concentrate moisture content vary within a range of seven to nine percent, but controlling the moisture content below eight percent is a difficult task with a manually controlled system. Many times, delays in manually achieving reliable feedback of the moisture content results in the moisture varying from five to twelve percent before corrective actions can be made. This paper first reviews the traditional and widely available methods for determining moisture content in granular materials by applying physical principals and properties to measure moisture content. All methods are in some form affected when employed on mineral ore concentrates. This paper introduces and describes a unique and promising novel on-line moisture sensor employed for mineral processing de-watering applications, which not only automates the tedious tasks but also results in reliable moisture feedback that can be used in the optimisation of the de-watering process equipment such as pressure or vacuum filters and fuel-fired driers. Finally, two measurement applications will be presented to indicate the usefulness and to summarise the measurement requirements for the proposed method of employing drag force and mechanical properties of the material itself to determine the moisture content. The commercial model of the equipment is described with the features and benefits to the users summarised.

Jan 1, 2003

As an Inspector of Mines in Queensland, my main responsibilities include the enforcement of the Mining Act 1968 - 1986, the Mines Regulation Act 1964 - 1983 and the Metalliferous Mining regulations 1985 to promote the safe and responsible exploitation of the States' mineral wealth. An important adjunct to this task is the offering of an advisory service to the mining industry. However, in the pursuit of my duties to this regard, I have sadly observed in some cases, numerous wrong doings and negative activities by miners which have led to their ultimate demise, not to mention that of others. Despite what I consider corrective advice, I have witnessed, again in some cases, disregard and blind pursuit for the wrong end. This then is a novel approach to get the message home in the form of a light hearted cartoon presentation relating the saga of an average Aussie battler entering the mining game unprepared, making the wrong decisions due to his own ignorance and the cleverness of others, leading finally to his and possibly others' downfall. It is not intended to insult any particular profession or group of individuals and only endeavours to impart to readers and listeners, the message of being prepared and alert when entering the gold mining industry. Even though the presentation focuses on the woes of a rookie alluvial gold miner, a similar analogy could be drawn with his hard rock counterpart since the basic issues that I have attempted to address are common. By no means is there a saga complete because there are many more traps a miner can inadvertently fall into and only time has prevented me from referencing them.

Jan 1, 1989