Search Documents

By G C. Lukey, J S. J van Deventer

The disposal and subsequent encapsulation of mine tailings in a cost-effective and environmentally secure and responsible manner is one of the principal issues facing any modern mining project. A careful assessment of all options available for the capping and subsequent remediation of tailings is important because it can result in large capital, operating and closure cost-savings. For these reasons, the technology of geopolymerisation is receiving increasing attention for the stabilisation and solidification of waste materials produced from mining operations. The first part of the current study investigates the application of geopolymer technology to the capping of hypersaline mine tailings. It has been found that suitable geopolymeric materials which have satisfactory compressive strength, durability as well as low permeability, can be formed using between 60 - 75 per cent of mine tailings as the main ingredient. It has been established that geopolymeric materials have the ability to suppress dust generation and prevent salt precipitation on the surface of the mine tailings. The slurry-like consistency of geopolymers would promote efficient application procedures through established tailings disposal techniques. This is a possible close-out technique for hypersaline tailings storage facilities such as those commonly found in Western Australia, which meets both regulatory requirements and community expectations. The immobilisation of contaminant metals within geopolymers has been investigated in the second part of the present study. In particular, the leaching characteristics of Cu and Pb from geopolymeric matrices derived from different fly ash sources have been examined. Potential breakdown of each geopolymer containing metal contaminants due to the leaching of Si and Al from the geopolymeric matrix has also been investigated.

Jan 1, 2000

Prospecting in arid terrain can produce substantial environmental impacts, comparable to or greater in magnitude than the impacts associated with actual mining or petroleum production. Impacts are likely to be particularly severe where prospecting involves intensive geophysical exploration, especially in areas which have escaped degradation by other land uses such as pastoralism. With appropriate environmental planning and management, however, the environmental impacts of prospecting in arid terrain can be greatly reduced and mitigated, at low cost. In many countries, prospecting licences, exploration leases and associated tenements now carry a range of conditions relating to environmental protection. The assessment, avoidance and mitigation of environmental impacts is therefore an important component of and-zone exploration. My aim here is to give an overview of some of the main aspects of an environmental planning and management (EPM) programme for prospecting in arid terrain (PAT). Detailed operational prescriptions for environmental protection procedures are necessarily specific to particular areas and types of prospecting: see. e.g., Buckley (1982a, 1984, 1985a, 1986a), Klepacki et al. (1985) and Stone (1986). The intention here is to provide a checklist rather than a recipe book: as an aid in incorporating environmental aspects into the overall planning and management of an exploration programme, and in liaison with company environmental staff, consultants and regulatory bodies. I also hope to show that whilst some of the techniques used in particular environmental disciplines certainly require specialist expertise, the overall design of an EPM programme is not in the least esoteric, but simply an exercise in straightforward common sense. Perhaps this paper could be subtitled: "Demystifying environmental Planning".

Jan 1, 1988

Today, more and more tunnel ventilation systems are based on NO2 (or NO) and visibility measurements. Due to the significant decrease of CO emissions in countries with EU emission standards, which were adopted by Australia in 2004, CO is no longer a key factor for tunnel air quality monitoring and is often only measured for plausibility reasons (eg according to the German guideline RABT2006). Nitrogen dioxide, which is a good indicator for the overall air pollution along roads, is now taking over the leading role not only for ventilation control but also for air quality monitoring and in future probably for checking the function of air filtration plants in tunnels. Due to the lack of equipment for reliable and long-term NO2 measurements in road tunnels in the past, there are only very few standards giving limit values for NO2 in road tunnels. Furthermore there are not many records of NO2 readings over longer periods in different types of tunnels. SICK MAIHAK, a major supplier of measurement devices for controlling tunnel ventilation, has introduced the first monitor in 2006, specifically designed for measuring NO2, NO and visibility simultaneously in road tunnels. There are now experiences and results from the first tunnels equipped with this kind of system. This paper will present and discuss the results and experiences from these tunnels and explain the different levels of NO2 in different tunnel types. Furthermore, the status of air quality standards for road tunnels regarding NO2 limit values and the current status of discussion in various countries about NO2 limits will be presented.

Jan 1, 2008

If an orebody has been drilled to achieve some level of regulatory compliance, then a number of associated geological databases will exist, representing 10 000 to 100 000 m plus of core intervals. The databases usually contain data about assays, lithology, mineralisation and geophysical attributes. They will also include location information such as collar positions and downhole surveys. Obviously this data is collected by geologists for, predominantly, geologists and mining engineers. However, from a process design viewpoint process engineers usually ignore the geology where possible and rely on a small number of metallurgical test samples. Typically these test samples are sourced from convenient and available cores or from a small number of specially drilled metallurgical holes. One of the worst instances known to the author was the design of a SAG mill using only two SAG specific test results (one for each of the major ore types) while, geologically, the orebody was defined by more than 30 000 m of drilling. This paper sets out a philosophy to maximise the use of the geological data, both for process design and in preparation for the commissioning phase of projects. Geological data is used in the identification of preferred locations for metallurgical test samples, for checking the metallurgical validity of the geological ore-type definitions, where necessary developing new ore-type definitions (geometallurgical domains) and developing mathematical relationships for the estimation of important metallurgical factors across the geological database. If the estimation of factors (for example ore competence) is considered reliable enough then there is also the possibility of feeding calculated data back into the block modelling process to allow the generation of metallurgically relevant outputs in the mine plans.

Jan 1, 2007

By M Titley, M NoppT

A study on the feasibility of mining the recently discovered Wallaby gold deposit is due for completion by mid-2000. Open pit mining is the favoured method. Determination of the impact of mining bench height on the recovery of ore, including the estimation of dilution and ore loss, is critical to the economics of the operation. Conditional simulation was used to derive a number of gold estimation scenarios within a typical volume of the deposit. These scenarios were interrogated for a selection of mining bench heights and ore block dimensions. The results were reported as a range of grade tonnage relationships and compared to the kriged resource model. This allowed the resource model to be calibrated to a specific mining bench height and ore block size. Once calibrated, more realistic dilution and ore loss values for a number of mining bench heights were calculated from the resource model. These values were then used to determine the economic sensitivity of particular mining methods. The spread of results from the simulations also provided an indication of the confidence in the kriged grade estimates for the different zones of mineralisation within the deposit and highlighted areas of any significant uncertainty.

Jan 1, 2000

By O Aydan, K Sugiura, A Sakamoto

It is well known that some sinkholes or subsidence take place from time to time in the areas where abandoned room and pillar type mines exist. The authors have been involved with the stability of abandoned mines beneath urbanized residential areas in Tokai region and there is a great concern about the stability of these abandoned mines during large earthquakes as well as in long term. The 2003 Miyagi Hokubu and 2011 Great East Japan earthquakes caused great damage to abandoned mines and resulted in many collapses. Particularly the effect of the quality of backfilling of abandoned mine below the urbanized areas is very important under static and dynamic conditions. The authors present the effect of the quality of backfilling on the ground subsidence associated with abandoned lignite mines under static and dynamic conditions and discuss its implications on the urbanized areas above abandoned lignite mines in this study. CITATION:Aydan, O, Sugiura, K and Sakamoto, A, 2018. The quality of backfilling of abandoned lignite mines on ground settlement under static and dynamic conditions, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 134–141 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By P A. Grossman, J H. Rubinstein, M Brazil, D Whittle

Many ore reserves are harvested by a combination of open pit and underground mining methods. In these cases, there is often material that could be mined by either method, and a choice has to be made. The area containing this material is referred to as the transition zone. Deciding where to finish the open pit and start the underground mine is referred to as the transition problem and it has received some attention in the literature since the 1980s.In this paper, we provide a review of existing approaches to the transition problem encompassing: graph theory-based optimisation employing an opportunity cost approach, heuristics and integer programming. We also present a novel opportunity cost approach, that takes into account a crown pillar, and show how the new approach can be best applied through the unconventional application of an existing mine optimisation tool.CITATION:Whittle, D, Brazil, M, Grossman, P A, Rubinstein, J H and Thomas, D A, 2016. Determining the open pit to underground transition – a new method, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 731–742 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

One of primary causes of poor blast performance is the improper relief of explosive energy. Under or over-confined blasts modify the explosiveÆs path of least resistance, which changes where and when the explosive energy is applied resulting in less than optimum blast performance. During the research for this paper the overbreak characteristics of five full-scale blasts were quantified using high speed cinematography and borehole cameras. The effectiveness of various overbreak control methods was also evaluated to guide design refinement. The results of this research along with general recommendations for reducing excessive damage are included with this paper.

Jan 1, 1999

By N LaBranche

The resurgence of Silicosis and Coal Worker’s Pneumoconiosis (CWP) in coalmines has placed the spotlight back on the management of worker exposure to particulate matter across all mining sectors (Coal Workers Pneumoconiosis Select Committee, 2017). There already exists a substantial body of knowledge on particulate matter and its impacts upon human health (National Academies of Sciences, Engineering and Medicine, 2018). The contribution of silica to respiratory disease is well known. However, it is also clear that there are major gaps in our understanding. In part, those gaps relate to the contribution to adverse health effects of mineralogical constituents in the dust (LaBranche et al, 2021a). It is also becoming evident that the size and shape of the particulate matter can affect its potential impact on human health. The University of Queensland has developed a methodology for characterising respirable and inhalable dust samples using scanning electron microscopy. Multiple samples from numerous mining operations have already been analysed using the UQ methodology. The process has been successful in showing the variety of mineralogical components and particle size distributions present in various areas of the mines.

May 5, 2022

By C Fearon

This paper discusses the implementation of an underground rail haulage system during a major expansion of the Olympic Dam mine in 1998. The factors affecting the selection of rail haulage are discussed and details are provided on the rail system, which is designed to transport more than 10.5 million tonnes per annum (Mtpa). The reliability of the system during commissioning is discussed, including the decision to manufacture a ædummyÆ locomotive in order to keep the system operational. Finally, reliability improvements made both during and after commissioning are discussed with comments provided on the effectiveness of the system as it operates today.

Jan 1, 2005

Rock bolting has become the most important method of ground support at Mount Isa. Various types of rock bolts are used to suit the different applications and requirements. To apply rock bolting techniques satisfactorily, it is necessary to have some knowledge of the nature of the rock, the type of rock failure, any stress redistribution which may occur during the intended life of the rock bolt and the time for which ground support is required. At Mount Isa there are a number of dif- ferent applications of rock bolts for ground support, and some trends in rock bolting techniques.

Jan 1, 1971

By Hohnen CA, Limerick JM, Hall DRT

An uniquely-designed flash furnace for smelting of nickel concentrate and for the recovering of metal values from the slag generated has been in successful use for nearly six years. Within the last eighteen months the ability of the furnace to treat slag arising from converting operations without significant reduction in capacity has also been successfully demonstrated. Previously, converter slag had been treated separately in an electric furnace. The salient features of smelter developments are outlined and slag chemistry is discussed. The low cost method for the introduction of coal to partially replace light fuel oil is reviewed and total energy requirements evaluated.

Jan 1, 1984

This paper carries on from an earlier paper 'Cemented fill practice and research at Mount Isa' and reports further on the laboratory programme at Mount Isa to develop a cheap cem- ented fill using Company waste products. The practical economic significance of availability of cheap cementing agents is re- viewed, with the various alternative approaches available The basic approach adopted within this paper is that use of reactive pozzolans such as ground slags to replace a proportion of the Portland cement in the fill can make mining methods employing cemented fill more economic- ally competitive with other mining methods.

Jan 1, 1973

The port of Townsville is situated on the main north/south rail system of the Queens- land Government Railways and is the eastern terminus of the east/west rail link from Towns- ville to Mount Isa. With a stable beef and wool producing area along the east/west rail route, the expanding mineral industry development at its western end and the continuing growth of the Townsville region the administrators of the port are continually'keeping abreast and ahead of port development to ensure an effective and economic growth of port facilities to meet the needs of the area served by Townsville.

Jan 1, 1974

By McPherson M. J

An experimental investigation was carried out to determine the various gas flow characteristics of bituminous coal samples. Adsorption and desorption tests were first conducted to estimate the quantity of methane that is retained by coal, and the rate at which it is released. Experiments were then carried out to study the variation in coal permeability with changes in applied stress and gas pressure - factors that change continuously with time. To further understand the phenomena involved in retention, release, and flow of gas, electron microscopy was used to study the microstructure of coal and how it affects these characteristics of coal.

Jan 1, 1988

By R Terracciano, J Schneider

Willemite (Zn2SiO4) is one of the main zinc carriers in several Neoproterozoic carbonate-hosted non-sulfide deposits ofNamibia and Zambia. Willemite commonly replaces sphalerite, but it may also replace the carbonate host rocks. Fluid inclusions, cathodoluminescence petrography and trace element geochemistry are crucial to distinguish between hypogene, high temperature and low temperature (possibly) supergene willemites. A global period of willemite mineralisation, extending from Cambrian to Lower Ordovician has been proposed for the southern hemisphere. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

The resources industry is unique in that the finite nature of resource deposits requires a participant to be constantly locating and developing new ones to replace those that are depleted. An effective growth strategy that enables new project developments to be brought on line in time and within budget is therefore of fundamental importance to any mineral resources company. This paper seeks to identify the role of the development project in the company's overall growth strategy and the key performance criteria that a development project must achieve in order to allow a company to meet its growth objectives.

Jan 1, 1997

The physical phenomena which influence gas flow in the bosh and hearth of a blast furnace are discussed including the hold-up of slag as a mechanism which can result in a flooding condition. An equation is defined which describes the limitation to wind volume arising from the flooding condition. Implications of the various factors influencing bosh and hearth gas flow on furnace operation are discussed. Coke quality is shown to be the most important factor in the aerodynamics of these zones and coke requirements are defined for the Port Kembla No. 5 BF which has an inner volume of 2670 m3.

Jan 1, 1975

By K H. Esbensen

During the next five years Denmark will implement a significant reduction in the national CO2 emissions to fulfil the Kyoto Protocol. The energy sector is central for achieving this goal and extensive use of renewable energy is the most important single factor contributing to reduce emissions of greenhouse gases. DenmarkÆs renewable energy sources comprise wind energy and biomass. Wood chips and straw are the dominant type of biomass in Denmark. More than 500 000 tons of wood chips are used annually, currently with rapidly growth prospects. This contribution focuses on sampling of wood chips.

Jan 1, 2005

By Parkes DB

The excavation of sandstone of generally medium strength for the Liverpool Link Line by Dosco Mark 2A Roadheaders has demonstrated the versatility and good performance of road- headers in suitable rock formations. A description is given of the strata traversed by the tunnels together with descriptions of equipment and crews, excavation sequences, operating difficulties and the results achiev- ed. In addition tunnel construction is des- cribed for a difficult section where there was only O.Sm clearance between invert and a four lane vehicular tunnel below, and O.5m clearance between tunnel crown and a century old sewer above.

Jan 1, 1976