Search Documents

Gravity concentration of tin at Renison Limited uses tables and spirals to treat the various coarser fractions produced from sulphide flotation tailing. An acceptable final tailing cannot be made from one pass over the tables and spirals and therefore the tailing from these separators is reground and combined with the sulphide flotation tailing as the feed to the classification section. The gravity section became increasingly overloaded in the years preceding 1976 due to efforts to maximize tin recovery to the gravity concentrate. In April, 1976, two 2DSV Reichert cone concentrators in series were installed to treat the table and spiral tail- ing stream, prior to regrind, to scavenge a small tonnage of hard, coarse low tin grade material for rejection to final tailing. Gravity section loadings were decreased markedly, allowing operator attention to be directed more to table performance than to spillage collection. An increase in mill throughput of approximately 15% was possible following the commissioning of the Reichert cones. The cones are currently operated to make the minimum tonnage of tailing consistent with reasonable- gravity section loadings.

Jan 1, 1978

Key blocks occur on the surface of excavations and on the walls of the ornamental stones and limestone quarries due to the formation of joint planes, fissures, microfaults and quarrying operations. Movements of these key blocks have produced numerous important failures and are responsible for routine overbreak and rock falls accounting for great costs. The thrust of this work is to demonstrate how to delimit zones of poten- tial key blocks (danger zones) in the wall of Bani-Khalid quarry of lime- stone by using the block theory technique (stereographic projection). The final result of this study indicated that, there are three potential key blocks, the most critical one has been determined. To treat the problem, we sug- gest either to provide timely support to prevent the movement of this block, or to analyze it further in hopes that available friction on the faces will hold it safely in place.

Jan 1, 1989

By G Cormack

By designing comminution circuits for mineral liberation rather than the final recovery process and by using high mass pull gravity recovery, the concept of underground processing has become a reality. Gekko has found that many ores respond favourably to fine crushing with either high pressure grinding rolls or vertical shaft impactors which when combined with the InLine Pressure Jig gravity separator and coarse flotation results in a narrow, low-head, compact processing plant that can be sensibly fitted in existing underground openings. The focus on fine crushing reduces the power requirements of the plant to approximately 5 kWh/t for a capacity of up to 20 t/h run of mine ore feed. The use of water recycle systems places no extra load on the mineÆs normal water handling system. GekkoÆs underground processing plant, the æPythonÆ, has been designed to be towed down the decline or lowered down a shaft and is capable of being installed in sloping, non-linear drives for placement close to the working face. The overall benefit to mining companies of this concept has been estimated to be a significant operating cost-saving, lower cut-off grade and a significantly smaller environmental footprint.

Jan 1, 2008

The accuracy of an ore reserve is only as good as the geologist's understanding of the deposit. The methods that are applied to resource and reserve estimation reflect that understanding. At the Olympic Dam copper-uranium-gold deposit in South Australia, evolution in the understanding of the controls on mineralisation coupled with the changing demands of the project have led to changes in the approach to reserve estimation. The project has moved into a phase where detailed stope mining reserves are now required as distinct from global ore reserves. The complex nature of the mineralisation and the large amount of data demand that all available information be readily accessible in a flexible format. To enable the selective manipulation of geological and assay information and its characterisation, a relational database has been developed. For reserve calculations themselves, initial computations were based on a system derived from that used for the Kambalda nickel orebodies. The Olympic Dam system differed mainly in the use of statistical analyses in the estimation of grade instead of the previous polygonal area of influence weighting method, Three dimensional weighting techniques are now being used for local reserve estimates. Flexible facilities for raw data handling combined with grade estimation techniques which are commensurate with the mine geologist's understanding, produce detailed gridded and contoured ore zone models suitable for reserve calculations and stope designs.

Jan 1, 1987

By A Richmond

"In some lode-style gold deposits the geological (lithological) uncertainty may have similar economic significance as the grade uncertainty. In the absence of precise knowledge of the deposit geology, geological models of these types of deposits that are used to constrain spatially the estimated (or simulated) grade values may influence significantly the contained metal. Methods for assessing geological uncertainty quantitatively are rarely considered due to their perceived inability to consider exhaustive geological interpretations, and resulting models that often appear geologically unrealistic. Furthermore, should the lodes have been subjected to folding, or where the mineralisation continuity does not follow a planar orientation along strike or down dip, standard methods of variography and interpolation using linear vectors in space often do not provide a good representation of continuity. An alternative approach is to relate spatial samples from adjacent drill holes using an unfolding plane.The paper demonstrates conditional simulation of the geometry and gold grades of a folded lode-style deposit where:simulation of lode geometry considers explicitly the geologistÆs interpretation, andsimulation of gold grade values that consider explicitly the folded nature of the lodes.The results are contrasted to the traditional approach of linear vectors in real space for a single lode interpretation.CITATION:Richmond, A, 2012. Conditional simulation of a folded lode-style gold deposit, in Proceedings Narrow Vein Mining 2012 , pp 149-154 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 26, 2012

By Richardson G. W, Yap L. C

Friction rock stabilisers (FRS) are the most common steel-based ground reinforcement used in underground mines in Western Australia. As with any other steel-based product used in underground mines they are susceptible to corrosion, particularly under aggressive minewater and mineral conditions. Because of their thin-wall tubular construction and large surface area, the potential damage resulting from corrosion is considered to be more severe for this type of reinforcement than for other forms of reinforcement made of solid steel bars. Because of the obvious safety problems which may result from corrosion, both mine operators and regulators have raised concerns regarding the long-term effectiveness of FRS installed in underground mines in Western Australia. Although corrosion has been recognised as an important safety issue, the controls of corrosion in varied underground mining environments has not been well understood. To improve the understanding of the corrosion behaviour of FRS, the Department of Minerals and Energy has initiated a research project focused on the mechanisms and extent of corrosion attacks, and their influence on the effectiveness of the reinforcement. This paper describes the research project and presents the interim results achieved To-date.

Jan 1, 1995

By C Li

Removal of gangue minerals from ilmenite concentrates can beaccomplished by relatively low temperature roasting in controlled gasatmospheres to selectively enhance the magnetic separationcharacteristics of the ilmenite. At roasting temperatures below 800¦C the magnetising reactions are often not consistent with phase equilibria considerations. Metastable phases can nucleate and control the roasting products. In weathered ilmenites the phase assemblages and microstructures in the altered ilmenite grains can influence the roasting reactions. In this paper we give an overview of the phase chemistry of chemically weathered ilmenites and of metastable phases formed by low temperature roasting. We also report the results of roast experiments conducted in a neutral gas atmosphere. Major increases in magnetic properties after short roasting times at low temperatures were obtained for a range of ilmenite concentrates. For example heating a secondary ilmenite concentrate from Western Australia for 15 minutes in nitrogen at 600¦C gave an increase in the three kilogauss magnetic fraction from three to 92 wt per cent. The solid state phase changes accompanying the inert atmosphereroasts were characterised by combining elemental analyses withquantitative phase analyses of the ilmenite concentrates and their roast products. It was found that the phase reaction that is principally responsible for the increase in the magnetic properties of weathered ilmenites involves a transformation of disordered ferrous-containing pseudorutile to an ordered ilmenite-hematite solid solution containing typically ten to 35 mole per cent of the hematite component. Examples are given of the application of the inert atmosphere roast to effect separations of ilmenite from gangue minerals.

Jan 1, 2001

This paper describes the application of the Total Productive Management (TPM) technique as a performance improvement initiative for a coal mining operation. It discusses the objectives of TPM, with the driver for improved production performance being the Overall Equipment Effectiveness (OEE) of the equipment or process, and with the development of "ownership" as the behavioral approach to equipment management and continuous improvement through cross-functional and area-based teams. It illustrates the concept of equipment management as defects management.The scope for application of TPM to the coal mining industry is immense. The harshness of the operating environment can be a major generator of equipment defects, and a current paradigm in the industry accepts these defects as an unavoidable outcome defining maintenance costs in this environment. However recent benchmarking studies have highlighted that maintenance costs per operating hour in some mining operations are more than double the vendor's estimate of "best practice". The paper refers to these studies which also compare maintenance costs of fixed and mobile plant and equipment to "best practice" outcomes in comparable process industries.

Jan 1, 1998

By Cornwell P. J

The Pajingo ore bodies consist mainly of auriferous quartz veins hosted by a suite of hydrothermally altered andesitic pyroclastics, volcanics and epiclastic sediments. Scott lode, the main economic deposit in the area, lies in a zone of major structural disruption and contortion. High grade gold and silver mineralisation is selectively mined by open pit methods. Standard grade control techniques and extraction methods were adapted to minimise mining dilution and to maximise metal recovery. Basic blending of grade ranges at the crusher has produced an average 10 gram/tonne gold head grade. The estimation of ore reserves calculated by both standard polygonal and geostatistical methods proved acceptable. Mineable reserves when compared to in pit reserves defined by blast hole drilling, indicate a decrease in tonnes and an increase in the grade resulting in an acceptable comparison of the total ounces of contained gold. The ore reconciliation of mined against milled ounces indicates that both ore reserve and grade control models underestimate the metal content in the orebody. Sampling techniques are being examined in an attempt to reduce this discrepancy.

Jan 1, 1989

The lignite mines in the Latrobe Valley of Victoria/Australia have been using continuously operating mining systems for more than 50 years. The relatively small bucket chain dredgers of the early years have been progressively displaced by bucket wheel dredgers with increasing size, increasing capacity and increasing service weight. The large machines for the new open pit Loy Yang have a bucket wheel outreach of 46m, an effective capacity of 3350 bm' coal/h respective 2500 bm' overburden/h and a serv- ice weight of approx. 4500 t. The time between signing of con- tract and starting of operation for these machines is at least four years. The high service weight, the resulting high capital invest- ment and the long period for design, design review, manufac- turing, erection and commissioning of these machines directed the SECV to investigate a possible application of compact dredgers for the Latrobe Valley.

Jan 1, 1989

By Hinkley JT, Smitham JB, Nicol SK

Historical investigations of mineral flotation have highlighted the many factors which affect flotation. Some of these are related to the mineral, its degree of liberation (however defined), solution chemistry and flotation reagents. The complexity of the interactions between these factors often leads to uncertainty over whether the final grade/recovery results obtained in either laboratory or pilot scale tests are in fact the maximum recovery at a specific grade. The reason for this is that there has not previously been a general technique for establishing the floatability of an ore. This study describes the further development of the 'tree' flotation technique for minerals other than coal, and in particular its application to iron ores. Oxides have been chosen as a system of intermediate complexity between the simple coal system and sulphide minerals to illustrate the principles and develop the concepts. The 'tree' flotation procedure consists of the progressive flotation to completion of successive froth products, followed by reflotation to remove entrained material. It therefore represents an 'equilibrium' approach to floatability rather than a kinetic approach. By ordering the various products and tails in order of increasing grade, a cumulative curve of grade and recovery can be constructed against which an isolated batch or plant result on the same ore can be compared. In this investigation, a Jaspilitic iron ore was tested at various grind sizes to determine the 'best' flotation grade-recovery that could be obtained with a given set of reagent conditions. The separation characteristics of a process are best measured on a system which contains particles which behave as 'middlings' with respect to the process in question. For this reason a natural ore was chosen in preference to model systems in order to relate more readily to plant situations.

Jan 1, 1993

By S Grano, M Fordham, H Manouchehri, J Curral

This paper focuses on the impact of high pulp temperature on sphalerite flotation after the zinc regrind circuit in the Zinc Plant of Somincor, owned and operated by Lundin Mining Corporation. In the zinc circuit, the zinc rougher concentrate is reground with forged steel media before flotation with one stage of roughing and scavenging, and three stages of cleaning to obtain a zinc final concentrate (zinc grade >50 per cent). After regrinding, sphalerite flotation has been found to be seriously affected by high pulp temperature which may occur during the summer months. Mineral recoveries were found to be seriously reduced at pulp temperatures above 60¦C. At this high pulp temperature, neither elevated copper sulfate concentration nor a decreased pH alone appreciably increased Zn recovery. However, a combination of these two (eg a decrease in pH from 11.5 to 10.8, and an increase in copper sulfate dosage from 400 g/t to 800 g/t) was found to reduce Zn depression at high pulp temperature. At pulp temperatures below 45¦C, the negative influence of pulp temperature on mineral recoveries was minimal. A systematic series of flotation tests and solution/surface analyses were performed to reveal causes for poor sphalerite flotation at high pulp temperature after regrinding. The decrease in mineral recovery was shown to be associated with variations in the surface species on mineral particles in response to the increased pulp temperature. These variations in the surface species include collector desorption and superficial oxidation to form lead/zinc oxide/hydroxides on mineral particles. The influence of the type of regrinding media on sphalerite flotation at high pulp temperature was also addressed in this work.

Jan 1, 2008

By G Steward

Gravity Leaching of high-grade gravity gold concentrates, such as Knelson Concentrates, with the ACACIA Reactor represents a new generation of concentrate treatment methods. The ACACIA Reactor is a complete packaged plant for the maximising of gold recoveries from gravity gold concentrates. This paper will introduce the process technology and provide process results from the Porgera ACACIA Reactor installation. The advantages of the ACACIA Reactor are many, and justification for installation has been varied. The typical advantages of the process include: increased recovery of gold from the Knelson Concentrate; no return of high-grade table tails, often grading several thousand g/t, into the mill circuit; reduction in tails grades of slow leaching gold; reduction in the requirement for operating staff by the removal of the manual tabling process and replacing with a fully automated treatment system; improved security by removing the tabling step where operating staff come into direct contact with visible gold; improved health and safety, by the removal of the treatment steps for the table concentrate, which often include operators handling corrosive chemicals and the production of sulphur and arsenic compound fumes; and improved metallurgical accounting, by allowing daily head grade calculations. The ACACIA Reactor was developed by Anglogold for Union ReefÆs Gold Plant and has been in production for over two years, and has proven to be a low cost, high recovery, mechanically reliable method for the processing of gold concentrates. Such has been the success of the plant, there are now four full installations of the processing plant, including Anglogold Union ReefÆs, Anglogold Sunrise Dam, PACMIN Carosue Dam and Porgera Joint Venture.

Jan 1, 2002

The fragmentation of whole rock by blasting has an influence on the subsequent loading, hauling and crushing operations. However, no method of calculating the frag- mentation has yet been developed. This paper gives a method of calculating the fragmen- tation for the simplest form of blasting, i.e. cratering. Cratering consists of the detonation of a spherical charge of explosive in a blasthole breaking to one free surface. This paper gives a method of calculating the extent of the system of radial cracks generated by the explosive in the rock. This system of radial cracks is then used to calculate the fragment size distribution curve from blasting. The calculated curves are shown to be in good agreement with experiment.

Jan 1, 1977

The first geological maps of parts of Australia were produced in the 1830s and 1840s, many being for purely practical purposes, such as indicating the occurrence of coal, iron and other essential materials. Mineral location maps were also first made about the same time.More systematic geological mapping commenced in the 1850s when large parts of New South Wales and Victoria were studied in government-sponsored surveys by geologists such as Samuel Stutchbury, Alfred Selwyn and Reverend William B. Clarke. Their work coincided with the opening up of most of the major goldfields of eastern Australia, which led to the establishment of Departments of Mines in the separate Colonies (later States within the Commonwealth of Australia).A few companies employed consultant geologists at this time, and the mapping by Frederick Odernheimer is particularly notable. Geological study of Australian ore-deposits and mineralisedareas was influenced by the continental European geological ideas of men such as Odernheimer as well as by those from England. Both geological and mineral maps were a feature of Colonialdisplays presented at major international exhibitions during the second half of the nineteenth century. The maps accompanied rock and mineral collections which showed the known and potential mineral wealth of the Colonies. Such displays raised interest in the potential for development amongst government officials, entrepreneurs and investors in Australia and abroad.By the 1880s most of the Colonies had produced basic geological maps, and several maps of the whole continent had been published. Although systematic mapping of the continent become a reality only in the 1950s, the nineteenth century geological and mineral mapping formed the basis for the development of the major coal, artesian water, and metalliferous mining regions of Australia.

Jan 1, 1990

By J Webb

Anoxic limestone drains (ALDs) have been widely used in the passive treatment of acid mine drainage (AMD), but their effectiveness has often been less than anticipated. Iron hydroxide often precipitates around limestone particles and inhibits neutralisation. To determine the conditions under which iron hydroxide precipitates, a small-scale laboratory ALD system was built to enable a detailed examination of the chemistry of iron within the drain. For one experiment, a mixture of limestone and quartz was introduced to the drain to assist in the determination of the key mechanism governing iron precipitation. Synthetic anaerobic acid mine drainage containing Fe2+ (~130 ppm), SO4 2- and H+ was pumped at a rate of 30 mL/min up a 90 cm tall, 15 cm diameter vertical column filled with limestone gravel of 98 per cent purity. Three sampling ports were fitted at equal intervals along the column; water was periodically extracted for analysis at the sampling ports over an 11-hour period. Experiments were run at influent pH levels of 2 and 4. Results show that acid neutralisation to pH greater than 6 occurred at the inflow end of the drain. The greatest amount of iron precipitation (19.5 per cent) also occurred in this area. The lack of iron precipitation on the quartz surfaces in the quartz/limestone mixture indicates that neutralisation is the key mechanism for the precipitation of iron hydroxide on limestone particles. A pe-pH stability diagram derived for the laboratory ALD system indicates that ALDs will not be effective for AMD with pH 2. Influent waters with pH 2 require a pe of -2 (Eh: -118.4 mV) to avoid Fe precipitation upon neutralisation. Influent waters of pH 4 require a pe between -2 and -4.

Jan 1, 2003

Detailed cash flow forecasts have always been almost essential as a basis for judging the viability of proposed new mining projects. In recent years attempts have been made explicitly to take account, in such forecasts, of the uncertainties surrounding the assumptions upon which they are based. With the risk analysis approach, Monte Carlo simulation of the cash flows indicates in probability terms the combined effect of these uncertain basic assumptions. While the use of risk analysis has been widely discussed, few specific applications to real projects have been reported. The application of such an analysis in the feasibility study of the large new Deelkraal gold mine presently being established on the Far West Witwatersrand gold fields by the Gold Fields Group in South Africa is described in the paper. The paper also indicates how one of the major sources of uncertainty, namely the gold content of the ore, can be`quantified in objective probability terms. This feature distinguishes the application fran other published accounts in which only subjective probability assessments have been utilised.

Jan 1, 1977

By Larkings RH

The high gas emissions associated with the depth of mining and very high coal extraction at some Australian Collieries have provided a need to investigate the influence of geological and mining conditions on levels of gassiness. The introduction of longwall extraction in particular is associated with complex strata control problems and quick changes in gassiness. To this stage of Australian coal mining, no standard method has been developed to predict the different levels of gassiness associated with the various geological and mining conditions; and the relationship between coal output and total methane make has not been established. For local conditions, with a large number of coal seams lying in close proximity to the working seam, the significant contribution of gas emissions from adjacent strata was expected, especially as strata relaxation occurred during longwall mining. This depends mainly on geological conditions, strata control and coal production. For the deepest of the B.H.P. Collieries in the Newcastle region, the relationship between coal output and total methane make has been investigated by systematic gas balance measurement during longwall extraction. The computer method of iteration was used to approximate the mathematical equation from the initial graphs of coal production versus quantity of methane in the ventilation system for various strata conditions. The angle of caving was established for local geological and mining conditions, for planning and design of the positions of cross measure boreholes.

Jan 1, 1986

The Beaconsfield Gold Mine within the township of Beaconsfield in northern Tasmania has been established in recent years to exploit a known resource in the Tasmania Reef which was mined to a depth of 450 m below surface between 1877 and 1914 yielding 850 000 ounces of gold. Activity at Beaconsfield over the past 30 years has involved drilling to assess the resource and rehabilitation of the top 100 m of the Hart Shaft that had collapsed since the original closure. More recently the mine has been dewatered to the 375 m Level and work is well advanced establishing infrastructure aimed at recommencing production during 1998 - 99. This paper reviews geotechnical studies undertaken to-date and provides a brief overview of some practical methods of analysing ground conditions. It pursues simple observation and analysis as a tool for assessing mine design and ground support options without recourse to extensive monitoring and measurement and avoids the use of elaborate models before the basics are understood.

Jan 1, 1997

By R M. Tosdal

The Manantial Espejo district (Argentina) hosts a low-sulfidation epithermal Ag (-Au) deposit with a proven and probable reserve of 38 Moz Ag and 0.55 Moz Au. The district lies along the southern rim of the Deseado Massif in the Middle to Late Jurassic Chon Aike Province, a large bimodal igneous province dominated by silicic volcanic rocks that were formed during the initial extension leading to the opening of the South Atlantic Ocean. The district stratigraphy consists of 162 to 161 Ma old rhyodacitic to rhyolitic volcaniclastic rocks of the Chon Aike and La Matilde Formations, followed by 160 to 157 Ma old andesites and dacites of the informally called intermediate formation. The main stage of normal faulting post-dates the volcanic activity and coincides with the formation of the precious metal veins that were dated by 40Ar/39Ar on hydrothermal adularia with ages between 152.8 ¦ 0.8 Ma and 156.6 ¦ 0.8 Ma. Economically important hydrothermal veins show characteristic features of a low-sulfidation epithermal deposit with crustiform and colloform banding, bladed calcite replaced by quartz and abundant adularia. In the Maria Vein, the major orebody of the district, six hydrothermal stages are identified, but only stages one and four contributed metal. Lead isotope ratios in hydrothermal sulfides show a close relationship to ratios in feldspars from the district Chon Aike Formation, suggesting a common source for the Pb and possibly the precious metals in both the magmatic and hydrothermal products, or that the Pb in the hydrothermal veins was derived from the volcanic rocks. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008