Search Documents

By D. M. Maijer, S. L. Cockcroft, S. Modak, A. B. Phillion

"A comparison between hydrogen-diffusion-based micro-porosity formation and growth behaviour of two important aluminium foundry alloys, B206 (Al-Cu) and A356 (Al-Si-Mg) is presented in this paper. Specifically, the predicted pore size and pore fraction distribution of these two alloys resulting from directional solidification and identical hydrogen concentration are investigated numerically based on a model proposed by Yao et al. (2011. Met. & Mat. Tran. A. 42A, 4137–4148). This model takes into consideration the initial hydrogen content in the melt, the cooling rate, the partitioning of hydrogen between the solid and liquid phases, and the evolution in solid fraction with temperature. Due to different alloy chemistries, the activity of hydrogen in B206 and A356 are quite different, as are the solidification range and the resulting solidification microstructure. Being a primary alloy, B206 has dendritic microstructure and solidifies over nearly 135°C (505–641°C), whereas A356 contains fifty percent eutectic microstructure, and solidifies over 80°C (533–613°C). This allows a very different behaviour of micropores i.e. the effective pore radius in B206 is quite a bit lower as compared to A356, as is the pore number density. The evolution of local hydrogen concentration in liquid metal is analysed and compared for both the alloys.INTRODUCTION Over the past decades, the demand for materials with enhanced strength-to-weight ratios has significantly increased in the aerospace and automobile industries in order to improved fuel efficiency. For many automotive components, particularly shape castings, the trend is towards replacing ferrous alloys with aluminium alloys. The increase in the use of Al is primarily due to its low density, about one-third that of steel, and its relatively good strength that allows for weight reduction without reducing performance. Presently, Al-Si based alloys (e.g. A356) are the most prevalent due to their good mechanical performance in strength-to-weight ratio and excellent castability (Atwood et.al., 2000). However, superior mechanical properties can be achieved using Al-Cu alloys. For example, the alloy B206 offers a higher strength while retaining excellent ductility (Poirier et.al., 1987)."

Jan 1, 2017

By B. C. Tripathy, S. K. Padhy, R. K. Paramguru, Pinak Patnaik

"Cobalt is regarded as technology enabling metal among the less abundant metals found in the earth crust. Electrodeposition of the metal from aqueous sulphate solutions is the preferred technology for its commercial production. Certain additives are added in the electrolytic bath during electrodeposition for the production of uniform, smooth and bright deposits of cobalt metal with higher current efficiencies and lower energy consumptions. A detailed investigation has been carried out to determine the effect of additive Sodium octyl sulphate (SOS) on the electrodeposition of cobalt. The results indicated that the additive apart from increasing the current efficiency enhanced the quality of cobalt electrodeposits. A maximum current efficiency of 98.4% was achieved at 10 mg/L SOS. The presence of SOS in the electrolytic bath did not result in any noticeable change in the crystal orientation of the cobalt electrodeposits except at higher concentrations (50 g/L) of the additive. Scanning electron micrographs indicate that smooth, compact and uniform deposits of cobalt were obtained at 10 mg/L of the additive beyond which there is detoriation in the quality of deposits. Polarisation of the cathode was seen in the presence of SOS. The effect of SOS on the electro kinetic parameters: Tafel slope (b), transfer coefficient (a) and exchange current density (I0) has also been investigated.INTRODUCTIONCobalt is recognised to be a strategic metal among the various base metals, owing to its numerous applications in various industries. Cobalt as a metal finds its use in the preparation of rechargeable batteries, as an alloying component in the manufacture of space craft and jet engines, as a drying agent for paint varnishes, ground coats for porcelain enamels and in the manufacture of the catalysts for the petroleum and chemical industries (Davis, 2000). Although there is a huge demand of the metal the supply of the metal is limited due to its scarcity in the earth crust. The metal comprises of only 0.02% of the earth’s crust for which the metal is recovered from various ores of nickel and copper as a byproduct (Hawkins, 1998). The present day techniques for cobalt production includes mostly hydrometallurgical methods which are preferred over the earlier used pryometallurgcial methods carried out for the metal production. Almost 70% of the world’s cobalt produced currently is from hydrometallurgical techniques in which electrodeposition of the metal from aqueous solutions is the final step for metal production (Verney, 1988). The most preferred route for electrodeposition of cobalt metal involves a sulphate medium (Das and Subbaiah, 1984; Lenthall and Bryson, 1997; Sharma et al., 2005)."

Jan 1, 2016

By D. R. Lentz, J. A. Walker

"Abstract -The Flat Landing Brook Zn-Pb-Ag deposit of the Bathurst Mining Camp occurs within a narrow thrust-bound nappe containing felsic volcanic and volcaniclastic rocks of the Tetagouche Group. Within the host nappe, the Tetagouche Group is represented by the Nepisiguit Falls Formation and the overlying Flat Landing Brook Formation. The Nepisiguit Falls Formation is divided into two members: quartz- and quartz-feldspar-phyric volcaniclastic rocks ± minor lavas (Grand Falls member), and aphyric, fine-grained volcaniclastic rocks (Little Falls member). The Flat Landing Brook Formation consists of aphyric rhyolite flows and interbedded pyroclastic rocks. Several gabbroic intrusions occur in both the footwall and hanging-wall sequences. These gabbros locally cut out the mineralized horizon at shallow levels, and are considered to be feeders to tholeiitic basaltic flows (Forty Mile Brook member) of the Flat Landing Brook Formation. The Flat Landing Brook deposit has many of the characteristics typical of volcanogenic massive sulfide deposits occurring within the highly productive Nepisiguit Falls Formation in the eastern part of the Bathurst Mining Camp. Mineralization occurs within or at the top of the Grand Falls member and comprises four or more massive to semi-massive sulfide lenses that vary in thickness between 3 and 5 m. Massive lenses are laterally gradational to, or underlain by, zones of disseminated sulfides up to 38 m thick. The deposit contains an estimated resource of 1.7 Mt grading 4.9% Zn, 0.94% Pb, and 19.54 g/t Ag to a depth of approximately 150 m. From 150 to 300 m below surface, mineralization is low grade and mostly disseminated. However, below 300 m, ore-grade (>10% Pb+Zn) massive sulfide lenses have been intersected over mineable widths. Oxide facies iron formation overlies and (or) grades laterally into the sulfide lenses. The oxide facies has strong positive Eu anomalies and gently sloping rare earth element (REE) profiles suggesting that it was formed from relatively hot acidic fluids that had interacted with felsic volcanic rocks in the footwall. In contrast, the silicate facies iron formation that is more distal to sulfide accumulations has very weak positive Eu anomalies and gently sloping REE profiles, suggesting either cooler hydrothermal fluids or dilution of the hydrothermal component by detrital material. Hydrothermal alteration has affected most footwall rocks. Most notably, albite-destructive alteration has resulted in Na2O depletion, whereas mass addition of K2O is manifested in the formation of sericite (white mica). In more intensely altered quartz- and feldspar-phyric volcaniclastic rocks of the Grand Falls member, feldspar destruction is accompanied by chlorite alteration, producing quartz-phyric rocks similar to those in the footwall of many Bathurst Camp deposits."

Jan 1, 2006

By F. Grant

"General *The mining experiences of the coal mining industry in Western Canada have been extremely varied, with the mining companies having to adjust their operations or fail due to the harsh economy of the country in the first part of the century. The bituminous or mountain mines had the railways as main consumers with, at times, optimism that potential steel producers would require metallurgical coal. The prairie and foothills mines mainly provided household fuels, with the fine coal sold to local thermal power plants at discounted prices. In practically all cases fuel competition was very keen, and the less successful mines ceased operations in short-time spans. Knowledge of the parameters that governed the success or failures of the past coal operations should be of value to the present and future mining companies. The initial coal mines were small and were started to supply local demand. These mines had little in the way of capital machinery, engineering, or transportation equipment; therefore the mining methods and mine plans were very simple. The first industrial-sized mines imported most of their management and mining methods from other mining areas, mainly Great Britain. It took time to change the bias of management and mining methods to the requirements of strata characteristics, with rapid closure to those mines that were slow to adapt working methods. The main markets for coal were for household fuel, thermal power plants and railways, with very few other industrial markets developed. The economy of the period was harsh and cyclic and the coal mines were affected more than most industries by these boom and bust periods. It led to the survival of the fittest or the most efficient. Due to the economy, mechanization was introduced to the mines very slowly, with the inability to sell coal fines at a profit being another reason for the delay. Manual labour with hand tools was the main means of production. The work was heavy and arduous, and the pay was based on contract coal tonnage; therefore both men and management paid close attention to details so that nonessential work could be eliminated. Mine openings were dimensioned so that coal could be loaded easily by hand and support requirements were kept to the minimum. Transporting and handling the timber supports required heavy labour; thus the most efficient dimensions were chosen to suit the strata. On the other hand, during the main production seasons the mines tried to make the strata stress work for them so that the pressure was kept on the coal face to keep the coal loose while the strata, a short distance back, was induced to cave to minimize the abutment stresses. This caused mining to be an art, using skills developed by experience with the strata. This led to the development of efficient mine layouts with the openings dimensioned to the strength of the strata and the type of support available. The lack of capital and mechanization, and the manual labour, induced the mines to correlate their service and haulage systems with their mining methods. This caused many innovations that proved very practical."

Jan 1, 1985

By Charles A. Taschereau

Burkina Faso ? Formerly known as Upper Volta; Country is landlocked and dry (Sahel sub-Sahara zone); ? Among poorest countries in the World, according to the United Nations Human Development Index (in 2005, 178 out of 179 countries; in 2009 173 out of 179); ? Population 13,9 Millions; Life expectancy is 51.4 years; Fertility rate 6.47 children/woman; Average age is16 years; literacy rate 23.6% and GDP per capita $1,213; ? French is official language; Politically stable country; very low criminality rate; corruption level low. Multiparty elections since early 90s; Legal and political systembased on French civil law system; ? Country just opened a few years ago to International mining companies, with a new mining code and investment code; ? No experienced labour; ? All new codes and laws; no established practices; Very limited economic development, mining is already main product of exportation and the country will become with Essakane a mineral economy (over 50% of total exports from mineral sources);

May 1, 2010

By D. G. Almond

Nkomati Nickel Mine in South Africa processes one of the world?s hardest ores in a 375k TPM autogenous grinding circuit. The plant employs an unconventional processing circuit, comprising a primary autogenous mill (AG or FAG) and pebble crushing circuit followed by a secondary hybrid pebble/ball mill and classification cyclone cluster. Advanced Process Control (APC) or Expert Control is now generally accepted as an advantage in most modern high capacity concentrator grinding circuits. This paper reviews the installation of model predictive control at Nkomati and examines the results and benefits of installation in an autogenous mill during plant ramp-up. The paper also demonstrates how predefining process control objectives together with good plant and supplier cooperation can achieve a robust and reliable APC implementation on a very short site program. The results conclusively demonstrate operational and economic benefits during circuit operation with the advanced process control system ON. Production performance and circuit stability were significantly better than during manual control.

Jan 1, 2012

By Robert J. Mitchell

A general approach to mine backfill design, including laboratory testing procedures, is outlined in this paper. Relationships between certain design parameters are developed and the effect of other factors is discussed. It is concluded that the inclusion of backfill design calculations at an early stage of mine design can often produce over-all design economies. Not only are the data needed for backfill plant and tailings disposal area design, but also the pillar recovery method and over-all mine stability are dependent on the attainable fill properties.

Jan 1, 1979

By A. I. A. Salama

The CANMET Western Research Centre (CWRC) has developed a hydrocyclone model simulation of dewatering and fine particle separation circuits. The simulation is based on an existing empirical model. Utilizing a cyclone manufacturer’s published data, some modifications have been developed and integrated into the model. Feed stream characteristics, cyclone mechanical dimensions, and operating conditions are used in the CWRC modelling simulation. The computer results are presented in 3D graphs and corresponding 2D maps showing the cyclone mass recovery, percent solids by mass in underflow and overflow, and cut size as functions of the cyclone apex diameter and cyclone throughput (i.e., inlet pressure or pressure drop). Results of the computer simulation have been used in the economic feasibility and design of several dewatering circuits in oil sand plants.

Jan 1, 2003

By CIM Environmental, Social Responsibility Society

Within the mining industry, the pathway from exploration, to planning, construction, operation and closure has become more complex over the last few decades. The current financial, environmental and social influences present the mining industry with unprecedented challenges and opportunities. In addition, international environmental and social reporting standards and codes are becoming increasingly robust. The reporting requirements provide an added impetus for issuers to effectively manage environmental and social impacts and risks. Reporting requirements also provide the opportunity to be transparent. The intended audience for these Environmental, Social and Governance (ESG) Guidelines for Mineral Resource and Mineral Reserve Estimation includes practitioners, industry participants at all levels of skill and experience, corporate management and board members, government agencies, academic institutions and interested parties. For practitioners, this document provides underlying key principles of environmental, social and governance practices. The ESG Guidelines provide guidance for those using environmental, social, governmental and governance information when preparing and implementing mineral exploration programs and contributing to the preparation of mineral resource and mineral reserve estimates for mineral properties that are either at the study stage (i.e., scoping / preliminary economic assessment, pre-feasibility, or feasibility studies) or in operation. The guidelines can also be used to help mineral resource and mining companies apply good practice to manage their environmental and social risks and opportunities. Companies can identify and retain appropriate professionals to prepare environmental and social materials to support company studies. The guidelines are also a resource for companies developing effective environmental and social management strategies at any project stage. This document is not intended to be prescriptive and is not intended to provide exhaustive guidance on what to consider in terms of environmental, social, legal and governmental modifying factors in the preparation of MRMR estimates. Rather, it is intended as general guidance to assist companies and practitioners in considering and applying these modifying factors for MRMR estimates. This document is also not intended to guide environmental and social impact assessment (ESIA); however, the measures needed to manage impacts help inform the constraints and costs for defining mineral resources and mineral reserves and inform the costs and schedules of mineral project studies. All documentation of MRMR estimates made by an issuer and intended to be, or reasonably likely to be, made available to the public in a jurisdiction of Canada must comply with the requirements of National Instrument 43-101 Standards of Disclosure for Mineral Projects (NI 43-101), as amended from time to time (Canadian Securities Administrators, 2016a and 2016b). Disclosure is not addressed in these ESG Guidelines. Determination of what to include in disclosures is defined in the applicable Securities’ legal frameworks. Appendix A presents a summary table showing the linkage of the principles and topics in these ESG Guidelines to the potential effects on project costs, schedules, government permits and approvals, social licence to operate and financing.

Sep 8, 2023

By Christoph Mueller

Broad band mine communication today is characterized mainly by individual solutions, which have in common their long development phases and their high cost for development, operation and service. The use of Ethernet and TCP/IP on the other side provides an uniquely price efficient combination of high bandwidth open networking, universal use and accessibility of cheap development tools, especially because it forms the technical infrastructure for the worldwide Internet. TCP/IP and Ethernet assures reliable networking however it is not able to guarantee the latency timing of forwarding network information. Therefor, the network design requires strict load limitation and application level traffic control especially if moving equipment has to be manually remotely controlled via the network. To optimize the use of bandwidth on mining networks using load limited, ?bandwidth wasting? local Ethernet segments, long distance broadband traffic should be carried out using more efficient, deterministic communication backbones providing a guaranteed quality of service for each of the physically separated networks. Open networking and broadband systems however may lead to the anticipation that any demands on bulk data or multimedia traffic can be fulfilled in the future. This definitely will not be the case as the bandwidth demands of applications will be growing as least as fast as the bandwidth provided by communication systems. Looking on those problems from an overall system integration perspective, machines and equipment in the future have to be equipped with intelligent computing devices capable of an intelligent local data preprocessing. Such ?Embedded Machine Information Servers? running commercial computing power in the future will be the intelligent bridge between open networking and a secured, high safety local automation system. These ?Embedded Machine Information Servers? then also can make advantage of intelligent video and audio data preprocessing to store and transmit multimedia information ?on demand? or when the application requires it. Summarizing the potential for the future Ethernet based networking together with powerful communication backbones and intelligent local data preprocessing on the machines in the future will lead the way to integrative, reliable and cost efficient mine automation solutions.

May 1, 2002

By Marcel Vallee, D. C. Gagnon, C. CARBONNEAU, P. ST-JULIEN

The Magdalen Islands archipelago, a cluster of fifteen islands, is located near the centre of the Gulf of St. Lawrence on the thickest portion of the Carboniferous Fundy Basin of the Maritime Pro vinces. The bedrock of the Magdalen Platform includes a thick succession of evaporites of Visean Age, occurring as a series of thickenings, ridges, domes and diapirs reaching a probable vertical thickness of close to 6000 m. The emplacement of 1hese salt structures by flowage has much dislurbed 1he SlrOligraphic sequence of the rocks of the Windsor Group, particularly 1he Havre-aux-Maisons Formation. Subsequent tectonic movemenl has broken the overlying Cap-auxMeules Forma1ion info an assemblage of panels and blocks now slightly tilted. Following detailed gravimetric surveys and more than 30,000 m of diamond drilling, SOQUEM has discovered, at various dep1hs, seven salt domes on four of 1he main islands of the archipelago. These evaporite bodies generally are localized near the cemre of complex anticlinal struclUres where diapiric movements and faulting have disturbed the original stratigraphic succession. At Rocher du Dauphin near Grosse 1/e, in 1he northern part of the archipelago, Seleine a SOQUEM subsidiary is developing a mining complex with an annual capaci1y of 1,250,000 1onnes of deicing salt for 1he Canadian and Eas1ern United Swtes marke1s. The stan of operations is scheduled for April 1982.

Jan 1, 1984

By J. E. Gill

"The name 'Canadian Shield' is used for a vast area; largely in northeastern; Canada; underlain by Precambrian rocks. The part in Canada has an area; of about 1; 790; 000 square miles. Extensions in Greenland; Labrador; Newfoundland; and the United States bring the total area to around 2; 800; 000; square miles. The boundaries of the Canadian part are shown in Fig. 1.; At its margins; the Precambrian rocks can be seen at many places to; extend beneath a cover of flat-lying Palxozoic or later sediments. Information; from borings in the Plains and natural exposures in mountain-built belts; show that similar rocks form a large part of the continental platform. The; Shield; therefore; is a large exposure of what may be regarded as the foundation; of the continent."

Jan 1, 1954

By C. M. Diaz, P. J. Mackey

Since its inception, in 1987, the Copper-Cobre series of conferences has established itself as the prime world forum for discussing advances in copper process metallurgy, in particular copper sulfide smelting, copper recovery by leaching and electrowinning and copper electrorefining. All copper producing countries have actively participated in the pyrometallurgy symposia held in the framework of these conferences. In 1999 and 2003, the close to 100 pyrometallurgy papers that were presented had to be accommodated in two volumes. In the present paper, the authors firstly provide a brief historical sketch of the Copper-Cobre conferences and then focus on providing a retrospective look at the dramatic changes that have taken place in copper smelting in the last few decades, primarily as discussed in the Copper-Cobre and precursor conferences pyrometallurgy proceedings. Topics include: the development of autogenous, increasingly more intensive, environmentally sound and energy efficient smelting processes; significant improvements in Peirce-Smith converting practice and at the same time the commercialization of alternative continuous converting routes; the consequent expansion and modernization of smelters; the increasing compliance with strict government environmental regulations in most copper producing regions of the world; the realignment of the copper smelting industry throughout the world; and trends in copper smelting R&D. A look at the future closes these reflections on the contribution of the Copper-Cobre conferences to the advancement of copper smelting technology.

Jan 1, 2007

By T S. Cochrane

This paper is based on observations made during a recent visit by the writer to three of the dust research laboratories .in West Germany, each .of which is mainly concerned with studymg the composition and character of the respirable dust produced in mines or at industrial sites. The three institutes are discussed as regards their orgamzat10n and duties, their methods of dust sampling and analysis, and recent trends in research and development. An extensive bibliography completes the paper. Introduction A RECENT trip to Europe to attend international conferences m Austria and m Belgium gave the writer the opportunity to visit a number of research laboratories and mines in Western Europe. The visits to the dust research laboratories in West Germany are the basis of this report. In Germany, cooperative associations formed prior to and since the turn of the 20th Century to promote the safety and welfare of their workers have recognized the effects of airborne dust on the general health of the labour force.

Jan 1, 1964

By B. Simonian

"The Mount Milligan mine, located in central British Columbia, began operation in September 2013 with a design nameplate capacity of 62,500 dry metric tonnes per day, using a conventional SABC grinding circuit followed by bulk sulphide flotation. Over the last few years, many changes have been implemented in order to debottleneck and optimize the comminution circuit to meet and exceed the nameplate design capacity as well as improve the metal recovery of the flotation circuit. This paper discusses changes, grouped into mechanical modifications, projects, and operational changes. The implementation of these changes as well as ongoing challenges and potential solutions will also be discussed.INTRODUCTION The Mount Milligan mine began production in the fall of 2013. It is a conventional truck-shovel open pit gold and copper mine and concentrator with a 62,500 tpd design capacity copper-gold flotation processing plant. The average head grades for the life of mine are 0.18% Cu and 0.39 g/t Au. At full capacity, the mine produces an average 400 dry tonnes per day of copper-gold concentrate containing approximately 21.5% Cu and 50-60 g/t Au. Current mine life is 21 years. This paper will discuss a selection of the operational, engineering, and administrative changes that have been made at the site since the publication of An Update on Reaching Nameplate Throughput and Continuous Improvement at Mount Milligan (Yue, 2017). PLANT FLOWSHEET CONFIGURATION Run-of-mine ore is crushed through a 60-110 gyratory crusher to a top size of seven inches. Up to 100% of the gyratory crusher product is diverted to the secondary crushing circuit by a moveable gate. The material diverted to the secondary crushing circuit is fed to a vibrating double-deck screen. The screen oversize is placed on a surge pile and reclaimed by four vibrating feeders to feed two 1250 kW standard head cone crushers in open circuit. The screen undersize is combined with the crusher discharge and returns to the conveyor feeding the coarse ore stockpile along with primary crusher product that by-passes the diverter gate."

Jan 1, 2019

By C. H. Hitchcock

History In approaching the subject of diamond-drilling practice, a brief history of the origin and development of the diamond drill may be of interest. The use of black diamonds for boring holes in rock was discovered in 1863 by Rudolph Leschot, a French engineer. In 1864, he employed a diamond bit to bore holes for blasting purposes in the construction of the Mont Cenis tunnel between France and Italy. The method was introduced and developed in the United States in the late sixties. The first deep hole was drilled for coal in 1870, near Pottsville, Penn., by M. C. Bullock. This hole was seven hundred and fifty feet deep. It can be inferred that the diamond drill was introduced into Canada in 1871, when a bore-hole, known as Harper's bore-hole, was drilled for coal at Springhill, Cumberland county, Nova Scotia; and at the old Silver Islet mine, near Port Arthur, the diamond drill was in use as early as 1872. Diamond Drills While M. C. Bullock was developing the diamond drill for exploratory work, the Sullivan Machine Company, of Claremont, N.H., was developing the diamond channelers and gadders for quarry work. These quarry machines were very successful until the high price of black diamonds became prohibitive. In 1878, Albert Ball, chief engineer of the Sullivan Machine Company, designed the Sullivan diamond drill so well known today. The first of these drills went to the Lake Superior iron ranges. After 1880, use of the diamond drill expanded rapidly and spread to all parts of the world where exploratory work was being done. In recent years, the type of diamond drill has not changed much, but better material is going into its construction. Steel castings have replaced cast-iron. Ball and roller bearings are now used instead of brasses and babbits. Gun lubrication has eliminated the oil-can. These improvements make a drill that can be operated for long periods without expense for repairs.

Jan 1, 1933

By Y. J. Yu, C. D. Zhang, Y. S. Zhao, W. G. Liang, Y. D. Geng, J. L. Bi

"In this study, the coefficient of thermal expansion (CTE) and thermal conductivity (TC) of shale in two perpendicular directions, vertical and parallel to the bedding of the rock, are firstly measured by experiment. The experimental results show that the CTE of the shale in the vertical direction is 1.69 times as much as that in the parallel direction, while the TC in the parallel direction is 1.83 times larger than that of the vertical direction. Based on the no initial strain assumptions, numerical simulations for the thermal cracking in shale are carried out with the obtained coefficients. Using finite element method and thermal-mechanical coupling theory, two fracture mechanical parameters, KI and J-integral of the shale are also analyzed for the shale thermal fracturing. The simulation results show that both KI and J-integral reach the maximum when the fracturing angle equals to 0° in the shale, namely parallel to the bedding direciton. It is also found that the two fracture parameters decrease with the fracturing angle increasing. Additionally, the thermal fracturing effect of the shale is evaluated under a given scenario. The study is significant for shale oil or gas recovery by in situ pyrolyzing method.INTRODUCTIONOil shale is regarded as a kind of unconventional resource that can contribute to production of shale oil and hydrocarbon gases (Rahm & Dianne, 2011). As is known that there is a large deposit of oil shale in China, and present technology for exploiting oil shale still concentrates on open-pit mining, obtaining shale oil by retorting shale on the ground (Li, Tang, Xue, Zheng, & Du, 2014; Qian, Yin, 2008). However, this technology has a bad effect on the environment and leads to severe resource waste for utilizing oil shale. Exploiting oil shale by in-situ method for ‘green mining’ is widely necessary in China (Kang, Wang, Cao, Liang, Chang, & Liu, 2013; Waters, Dean, Downie, Kerrihard, Austbo, & McPherson, 2009; Zoback, Kohli, Das, & McClure, 2012). One of effective method to exploit shale oil is heating oil shale in-situ underground. For instance, the in-situ conversion process (ICP technique) from Shell Company etc. used a direct heating method, and convectional heating oil shale underground by injecting superheated steam from Mining Technology Institute, Taiyuan University of Technology and constructing horizontal fracture in vertical wellbore from Chevron Company use indirect heating method (Chaudhary, Ehlig, & Wattenbarger, 2011; Hazra, Lee, Economides, & Moridis, 2013; Zhao et al., 2010). The convectional heating method contains complicated procedures with phase transition in double-media of fracture-matrix of oil shale subjected to multi-physical fields coupling including stress, fluid and temperature (Zhao et al., 2010). The characteristics of thermodynamics, solid mechanics and seepage of oil shale have been investigated separately (Hopkins, Rosen, & Hill,1998; Kang, Zhao, & Yang, 2008; Yang, Zhao, Kang, 2010; Zhao, Yang, Feng, Liang, & Kang, 2008; Zhao, Cao, Zhao, Lin, & Wang, 2008). However, it is quite difficult to solve constrained problem of each physical parameter in multi-physical fields coupling for oil shale pyrolysis."

Jan 1, 2015

By R. V. Typliski, G. J. Labarre

"Hudson Bay Mining and Smelting Co., Limited, Flin Flon, Manitoba, Canada, has developed a metallurgical wastewater treatment system employing two-stage lime neutralization, sludge recirculation and conventional mechanical thickening.Laboratory investigations, initiated in 1970, led to the construction of a pilot-scale minewater treatment plant, at Schist Lake Mine, in early 1971. This plant, treating 600 cubic meters/day wastewater containing 30-60 mg/l zinc, demonstrated metal extraction efficiencies of 99% under normal operating conditions.On the basis of this pilot work, a second pilot-scale treatment system was established in 1975 at the Flin Flon metallurgical plant to treat zinc refinery process waste water. Through numerous improvements, including automatic control equipment, the system has evolved to a full-scale operation capable of treating 800 cubic meters/ day wastewater containing 4-11 gm/l zinc. Treated effluent contains 0.2-20 mgll zinc. Hydroxide sludge produced returns to the metallurgical process for recovery of metals while clarified effluent discharges to waste.With the system, Hudson Bay Mining has achieved its original goal: the reduction of environmental contamination, while realizing ii return from metal recovery."

Jan 1, 1980

By Fred G. Hewett

The Cassiar orebody is located in a sill-like serpentinite body intrusive into the Devonian-Mississippian sedimentary rocks of northern British Columbia. Subsequent intrusion of the Cassiar batholith formed the McDame synclinorium and produced chrysotile asbestos. Present information indicates an orebody of approximately 16,277,000 tons amenable to open-pit mining, but continued diamond drilling will be needed to accurately define total tonnage and grade. A program has been developed at the mine to provide the required information on a daily basis, and work is continuing on more effective dollar-value prediction methods.

Jan 1, 1978

By C. Vanvoren

"Since 1975, the Aluminium Pechiney Research Centre at Saint-Jean-de-Maurienne (LRF) has been concentrating its efforts on designing, testing and perfecting the Aluminium Pechiney point-fed prebaked reduction cell.In 1979, the AP18 cell (180 kA) was industrially launched with the construction and start-up of the F line in Saint-Jean. The following generation, the AP30 (300 kA), with prototypes started in 1981, was launched in 1986 on the Saint-Jean G line. Along with cell design, efficient process control systems were developed to pilot alumina feeding and bath composition. Together, these pots are currently producing 4.6 Mt of aluminum, i.e., 18% of the world’s overall yearly production.In 1989, the research centre faced a new challenge: to push the limits for the size of a reduction cell to further improve the profitability of Greenfield projects. This new generation development was also the opportunity for a significant redesign of the Aluminium Pechiney electrolysis information system.With a track record of ten years of semiindustrial operation with three prototypes, the AP50 technology is now ready for industrial implementation and enables a significant breakthrough to be made in terms of return on investment of a Greenfield smelter."

Jan 1, 2002