Search Documents

By Linlin Tong, Xiangling Song, Guobao Chen, Zhenan Jin, Hongying Yang

Biooxidation of a high arsenic-bearing refractory gold ore was investigated to determine the arsenic removal efficiency by the cultured bacteria and to examine the effect of biological pretreatment on subsequent gold cyanidation. The biooxidation pretreatment process utilizes the ability of adapted acidophilic bacteria to oxidize pyrite and arsenopyrite and release the encapsulated gold. The released gold can be efficiently extracted by the subsequent cyanidation process. The biooxidation experiments were conducted with cultured bacteria using various sizes of agitation tanks. Leaching results showed that over 96.26 % arsenic extraction could be obtained from this ore after 6 days of bioleaching with continuous stirred tank reactor (CSTR). Gold extraction during the cyanidation process was increased from 29.35% to 96.71% after biological pretreatment. The content of arsenic in the biooxidation residue was reduced to below 0.3%. The transformation process of As was considered as [AsS]2- ? As (?) ? As (?) during the biological pretreatment.

Jan 1, 2014

1.Assessment of methane content in coal. Given a naturally low methane content in 11 Coal Seam and the fact that the areas of the 11 Seam adjacent to the tunnelway were degassing for a very, very long time due to previous development and mining, it is conservatively estimated that the remaining in -situ methane is less than 0.5m3/tonne. 2. Continuous miner cutting rate based on the past practice. The best loading rate recorded at the past operations of Smoky River Coal was 45 seconds for a 8 tonnes shuttle car. Using these records, the maximum peak loading rate potential at the face is calculated at 0.178 tonnes per one second or 10.67 tonnes per one minute. 3. Methane release at the face. ?The actual face methane liberation, conservatively assumed at 40% of the total in situ content: 0.20 m3/tonne ?The peak cutting rate: 0.178 t/sec ?The maximum (peak) face methane release: 0.20*0.178 = 0.036 m3/sec

May 1, 2003

By J. Armitage, J. Erskine

Feed level and thickness measurements are essential in the optimization of an electric arc furnace. A precise measurement of the feed thickness and level gives operators the ability to increase the smelter efficiency and reduce the maintenance cost. Hatch has developed a radar system which is an affordable, low maintenance, and accurate level measurement system. The radar units can be installed across the furnace to measure the feed level and the feed thickness can be calculated with one slag level sounding. The present paper describes the development of radar systems as a process optimizing tool by furnace controls. The authors will discuss the challenges involved in installing eight radar units on the roof of a six-in-line electric furnace.

Jan 1, 2015

By L. M. Lowe, D. B. Chambers, D. G. Feasby

"The presence of the naturally occurring radioactive elements uranium and thorium in rare earth (RE) resources can present challenges in achieving regulatory and social acceptance. The discovery and awareness of radioactivity in mineral resources radioactivity typically generates strong public intuitive responses that may be project prohibitive; a significant proportion of such resources contain radioactivity.The objectives of this paper are to demystify the presence of uranium and thorium in RE resources and to demonstrate how a RE project can be safely developed, operated and closed from a radiological perspective. Radioactivity in RE resources is principally thorium-based. Thorium is interesting and challenging from a metallurgical perspective – one of those stubborn metals commonly assessed as refractory. Thorium is difficult to mobilise into solution and easily precipitates out. Thorium is a common element in the earth’s crust – about 10 ppm on average, and natural geophysical systems conclusively demonstrate its immobility. Specific mine tailings contain elevated levels of thorium, but the contained thorium is neither a significant ecological nor a personal hazard.Waste management for a hard rock rare earth project includes the management of mineral processtailings, waste rock, and metallurgical residue. Proven strategies are available for tailings and waste rockfor all climate conditions. The management of the metallurgical residues is potentially more challenging.Example robust strategies for addressing these challenges are presented.A potential way to reduce the radioactivity of rare earth metallurgical wastes is to selectively remove uranium and thorium. Uranium oxide is readily marketable, but its concentration as a byproduct typically triggers extensive regulatory processes. Thorium is presently not marketable, but may be so in the not-too-distant future with the development of thorium-based nuclear energy. The pro’s and con’s of uranium and thorium byproduct recovery are summarized."

Jan 1, 2016

By C. E. White

History The Con-Rycon mine is situated in the Yellowknife mining district, North West Territories, 608 air miles north of Edmonton, Alberta. The earliest reported discovery of gold in the area was made in 1898 but no extensive exploration occurred until 1928. The birth of Yellowknife as a mining community took place in 1934 with the staking of the Rich group and subsequent shipping of 16 tons of high grade ore. The Giant group was also among the claims staked in 1934, and later staking showed a tendency to close the gap between these two properties. In the fall of 1935, the A.Y.E. claims, situated south of the Giant group, were staked to cover a discovery of the Geological Survey of Canada and, after general release of the Survey's information, the adjoining ground was staked. These claims included the Con, Negus, Meg, and Kam groups. In 1936 four lapsed claims were re-staked as the P and G group and later acquired by Rycon Mines, Limited, controlled by the Consolidated Mining and Smelting Company of Canada, Limited. The Con and various adjacent groups owned by Cominco are now operated with the Rycon under one management. Surface trenching on the Con property started in 1936 and, during the fall and winter of 1936-37, a 60- foot 5 ft. by 9 ft. inclined prospect shaft was sunk. The encouragement provided by the shaft and diamond drilling in 1937 led to the decision to establish a mining plant, and in August, 1938, the 100-ton cyanide mill produced its first brick- the first gold brick poured in the history of the North West Territories. In November, 1938, the mill was enlarged to a 175-ton capacity and operated at this rate until 1941, when refractory ore was encountered. This situation was met by the installation of flotation and roasting units and, at the same time, the milling capacity was increased to 300 tons daily. Labour shortages and Government restrictions forced a reduction of output and in 1943 milling was suspended while mine development continued on a reduced scale throughout the war years. The present full-scale of operations was resumed in 1946 and the total production to the end of 1948 amounted to 288,853 oz. gold and 72,347 oz. silver.

Jan 1, 1949

By F. Melo, M. Pawlik

Fine coal aggregation in concentrated coal-water suspensions was studied through steady-state rheological measurements. The wettability of coal particles was modified by dry oxidation of a bituminous coal. The degree of hydrophobicity was monitored using film flotation. The rheological measurements revealed that hydrophobic coal particles aggregate in aqueous suspensions, over a wide pH range, and produce slurries with high yield stresses. As the degree of coal oxidation increases, the coal particles become more hydrophilic and such suspensions exhibit lower yield stresses values. The yield stress values for suspensions prepared from oxidized/hydrophilic coal become a strong function of pH and correlate well with the surface charge as determined through electroacoustic measurements. These results indicate that the yield stress of aqueous suspensions of coal, and hence coal particles aggregation, is strongly affected by the wettability of coal particles.

Jan 1, 2004

By Marvin E. Lane

Viburnum, located in the foothills of the Ozarks in south-east Missouri, is the site of a modern lead mining and milling operation. Two mines are currently producing a total of 5,000 tons per day and a third mine is in the final development stage, with full production scheduled for late this year (1964). These mines will supply the tonnage required to keep the Viburnum mill operating at a full capacity of 7,000 tons per day for many years. The efficient underground mining operation is completely trackless. Drill jumbos are used to break the ore in a room and pillar method of mining. Transloaders, or St. Joe shovels, and trucks do the loading and hauling. The Viburnum mill has a world-wide reputation as a most efficient operation. This is due to the extensive use of automatic process controls, and labour saving materials handling facilities. Introduction THE St. Joseph Lead Co., has operated lead mines in southeast Missouri for 100 years. These operations have been confined largely to the area called the

Jan 1, 1964

By Roger J. Higgins

Papua New Guinea is a country on the cusp of development, struggling to find a balance between the demands of national and regional growth, landowner expectations and the maintenance of cultural identity. Ok Tedi Mining Limited is the single largest contributor to PNG?s economy, representing about 10 percent of the country?s GDP. OTML is demonstrating that business and country risk can be managed through effective, respectful partnerships with local communities. OTML?s relationships with the communities of PNG?s Western Province are multifaceted. Communities have borne the brunt of the mine?s environmental impact, yet have benefited enormously from the development that the mine has brought. Importantly, the PNG economy is now the ultimate beneficiary of more than four-fifths of the dividends from the mine, the majority of which are held in trust for long-term sustainable development projects. The paper describes how OTML works with the Western Province communities to create a secure operating environment that recognizes the people?s aspirations for development and self-determination.

May 1, 2002

By Charles Camsell

Few persons ever stop to consider how vital an influence minerals, and especially metals, have had upon human history, how they have affected the every-day life of the individual or how at different periods they have altered the course of nations and determined their progress. Students and writers of history have dealt very fully with political history and have given us a great deal of detail about the careers and policies of kings, parliaments and nations, but frequently have not touched the economic causes that have been the real forces influencing the development and carrying out of these policies. So far as minerals are concerned there is no single work from which one can get a concise and consecutive account of the growth in the use of minerals, nor of the diverse ways in which the. geographical distribution, the .search for, the development and the use of mineral resources have affected human progress from the beginning of man's history. The reason for this is quite plain, and when one takes a little time to think of it he begins to appreciate the magnitude of the job and he will realize that the story of minerals and mineral resources touches a tremendous range of human activity, not only of mining .and metallurgy, but the whole field of agricultural and industrial growth, of exploration and colonization, transportation and commerce, monetary system, commercial policy, in short, almost every phase of economic life.

Jan 1, 1926

By J. Jung, W. Keller, N. Rohn

In hydrometallurgical minerals processing slurries are often processed at very small grind sizes and high solids concentrations. This normally results in flow anomalies of such slurries. Due to flow limits or yield stress the slurry tends to stagnate close to the vessel bottom, the walls and at any internals. The main mixing task therefore generally is not suspending of the solids but the homogeneous blending of the entire vessel volume. If not considered during the agitator design only a fraction of the vessel contents will be mixed. Therefore the knowledge of the slurry rheology as well as the variations in process parameters is vital to design e.g. storage or surge tanks. The integral mixing solution considers the motor power, the choice of the impeller type and number, the impeller diameter as well as the design of the baffles and feed and discharge positions.

Jan 1, 2014

By C. A. Hardie, G. F. Leichtle, J. A. Finch, J. A. Watson

"The recycling of wastepaper has become an important and common process worldwide. Techniques similar to those used in the mineral processing industry are used to produce high quality recycled fibres for use in newsprint. The mineral processing group at McGill University, in conjunction with the Pulp and Paper industry (Mechanical and Chemi-mechanical Wood Pulp Network), has adapted one of these techniques, column flotation, for the purpose of deinking wastepaper. This article describes the typical process of recycling wastepaper from a mineral processing point of view. It also presents results from McGill University’s flotation column test work at a Québec wastepaper recycling facility. IntroductionThe recycling of wastepaper has become an important and common process worldwide, including Canada which is now the world’s largest importer of wastepaper (CPPA, 1996). Much of the current drive to increase the utilization rate of recovered paper is a reaction to the solid-waste disposal problem that faces many Canadian and United States municipalities. The real problem in the disposal of solid waste is not the absolute amount of garbage that must be disposed of each year, but this amount in relation to available disposal capacity.Environmental restrictions on the creation of new landfill sites and incinerators (the two main options for disposal of municipal solid waste) have tightened the demand/supply balance in the solid waste disposal market. This shrinking availability of waste disposal sites in the face of increasing population with greater disposal requirements defines the Developed World’s solid waste crisis. Not only are there fewer disposal sites available, but the costs of using them is skyrocketing. These factors have increased government regulations mandating recycled paper content in newsprint. Conservation and environmental issues make the current drive for wastepaper recycling a real issue and business opportunity."

Jan 1, 1999

By H. P. Dibbs

An account is given of the application of neutron activation analysis to the rapid, non-destructive determination of copper in minerals, using a 14-MeV neutron source. Elements that interfere in the determination of copper by this method are given, together with the errors in the estimation of copper that result from the presence of varying amounts of these elements. The possible use of a compact "sealed-tube" 14-MeV neutron generator for the field assay of copper in minerals is discussed.

Jan 1, 1970

By M. J. Davie, D. S. Ross

"The successful design of a new mine water pumping system is in part dependent upon the accuracy with which the operating conditions can be forecast. This paper outlines the data which should be obtained on water quantity and quality. Methods of modifying the quality are also discussed. Some pumping systems for disposal of sludge are described, citing operating examples. The various types of mine dewatering pumps are described in terms of design characteristics as they affect operating efficiency and installation and maintenance costs. Piping system parameters are outlined. Finally, a hypothetical case study of pumping from a depth of 3,000 ft is assessed, with particular reference to capital costs.IntroductionMany mine operators would agree that the pumping system usually receives a low engineering priority during the design stage, and as a consequence causes some of the most frustrating problems during production. For a ""dry"" mine (up to 200 gpm), design of the pumping system may indeed be simple, but outside of the potash industry such mines are not common. For ""wet"" mines, the pumping system is important because it significantly affects the initial capital and on-going energy costs of the mine and, in the area of sludge disposal, the working conditions and production costs. Indeed, a failure in the pumping system usually has serious, and sometimes disastrous, consequences.The intent of this paper is to outline the factors which should be considered in the design of a pumping system and to describe the types of pumps used in mine dewatering and relate them to practical operating systems."

Jan 1, 1980

By D. C. R. Espinosa, P. Aliprandini, J. A. S. Tenório, M. M. Jiménez Correa

"Nickel and cobalt are the main value metals in nickel laterite ore. Cyanex 272 is an extractant used to separate nickel from cobalt present in leach solutions. Previous studies demonstrated the extraction of cobalt, magnesium and manganese at pH 5 using Cyanex 272 as extractant, while nickel remained in aqueous solution. However, it is difficult to separate cobalt from a solution containing magnesium and manganese. One possibility to change the metals’ behavior during the solvent extraction process is to change the mixture of extractants used. In order to study the solvent extraction of cobalt from a solution containing manganese, magnesium and nickel, a mixture of two extractants was investigated. Cyanex 272 (CY) and Versatic 10 (VC) were selected as extractants in the organic phase. The extractant concentrations used were: 20% CY; 15% CY, 5% VC; 10% CY, 10% VC; 5% CY, 15% VC; and 20% VC. In all cases, kerosene was used as a diluent, at 80 vol%. The synthetic leach solution used in this study was prepared according to the composition of a typical nickel laterite leach solution. The pH value of the solution used was 5, and the aqueous/organic ratio used in solvent extraction testwork was 1/1. The study has shown that the composition of the organic extractant mixture did not increase cobalt separation.INTRODUCTION Sulfide and laterite deposits are the main sources of nickel. However, production from nickel sulfide ores has been decreasing over the years, relatively speaking, increasing the focus on the exploitation of laterite nickel ores (McDonald & Whittington, 2008). Laterite ore deposits are found in tropical and subtropical regions. A characteristic of laterite ores is the presence of a complex and heterogeneous mixture of metals (Crundwell, Moats, Ramachandran, Robinson, & Davenport, 2011; Georgiou & Papangelakis, 1998; Gupta, 2003; Kesler & Simon, 2015; Moskalyk & Alfantazi, 2002; Oliveira, 1990). Nickel concentrations in laterite ores are typically 1–2% (Dalvi, Bacon, & Osborne, 2004)."

Jan 1, 2017

By Mengmeng Gai

This paper introduces a model-based automatic object recognition and registration framework to assist heavy equipment operators in rapidly perceiving 3D working environment at dynamic construction sites. A video camera and a laser scanner were utilized in this study to rapidly recognize and register dynamic target objects in a 3D space by dynamically separating target object?s point cloud data from a background scene for a quick computing process. A smart scan data updating method has been developed which only updates the dynamic target object?s point cloud data while keeping the previously scanned static work environments. Extracted target areas containing 3D point clouds were orthographically projected into a series of 2D planes with a rotation center located in the target?s vertical-middle line. Prepared 2D templates were compared to these 2D planes by extracting SURF features. Point cloud bundles of the target were recognized, and followed by the prepared CAD model?s registration to the templates. The field experimental results show that the proposed rapid workspace modeling method can significantly improve heavy construction equipment operations and automated equipment control by rapidly modeling dynamic target objects in a 3D view.

Aug 1, 2013

By Mohsen Mohammadi, Edward Cyr

"To date, several studies have been performed on the static mechanical properties of SLM-AlSi10Mg alloy. There have also been more recent studies on the relation between scan strategy, texture, and mechanical properties of SLM metals and composites. However, there is a huge knowledge gap in the available literature regarding texture and mechanical behavior of SLM-AlSi10Mg alloy under high strain rates. Therefore, in this study, dynamic mechanical behavior of AlSi10Mg_200C alloy manufactured by DMLS technique was investigated at high strain rates ranging from 900/s to 1700/s using Split Hopkinson Pressure Bar. Texture using X-ray diffraction technique of the initial samples were measured. The yield strength, peak flow stress, and ductility increased in all samples with increase of strain rate. TEM studies have also revealed evidence of continuous dynamic recrystallization in grains after 900/s–1700/s strain-rate tests. A Taylor polycrystal crystal plasticity constitutive model was then developed to capture and predict the texture evolution and mechanical response under dynamic loading, using plastic work as a critical parameter for the onset of recrystallization.INTRODUCTION Additive manufacturing (AM) powder techniques are among the fastest advancing breakthroughs in manufacturing in recent years, defined by a bottom-up layer by layer process of joining with energy input from lasers or electron beam (Herzog et al., 2016; Gibson et al., 2015). Among alloys fabricated by SLM, AlSi10Mg is of high interest to industry and academia due to its low density, high specific strength and excellent corrosion resistance, making this alloy a viable contender for aerospace, automotive, and marine applications. Circumstances such as car crash or bird aircraft strike hazards subject potential additively manufactured AlSi10Mg parts to impact loadings. This drives an interest in understanding and predicting dynamic behaviour of these alloys. AlSi10Mg is the AM counterpart of A360 die-cast aluminum, which possess hypoeutectic microstructure (Li et al., 2015). Up to the present time, many studies have presented the mechanical properties of SLM-AlSi10Mg alloy. The mechanical properties and microstructure of AlSi10Mg produced by selective laser melting (SLM) or DMLS techniques can be controlled using different parameters, such as feedstock powder (Asgari et al., 2017), and process parameters (Olakanmi et al., 2015). The microstructure and mechanical properties of AlSi10Mg can also be controlled using post heat treatment after SLM process Li et al., 2016). The mechanical properties of SLM-AlSi10Mg are sensitive to strain rate and can both change under quasi-static (Rosenthal et al., 2017) and high strain rates (Asgari et al., 2018). However, a significant knowledge gap in available literature regarding modeling these behaviours, and especially micromechanical modeling of dynamic behaviour."

Jan 1, 2018

By Francis Perron

The Directive 019 on mineral industry, which was officially adopted in 1989, is the main tool used by the Quebec Ministry of Environment for the environmental evaluation and control of mineral exploitation projects presented for approval. This document contain the environmental guidelines which must be met by all the mineral companies during and after exploitation. The Directive 019 also contain all the information required by the Quebec Ministry of Environment in order to fully analyse the environmental impacts caused by the mineral projects proposed to the Ministry for approval. The proposed modifications of the Directive 019 cover many new topics that were not addressed in prior editions, these include : water recirculation, groundwater protection, tailings management and post exploitation environmental controls.

Nov 1, 2002

By R. Drozd

"The Bui/moose Mine is in the northeast coal area of British Columbia, and less than $300 million was spent to bring this 2.3 million-tonnes-per-year metallurgical and thermal coal mine into production by November 1, 1983, one month ahead of schedule. The project is an unincorporated joint venture undertaking, with Teck-Bullmoose Coal Inc., a wholly-owned subsidiary of Teck Corporation, holding 51%, Lornex Mining Corporation holding 39%, and Nissho-lwai (Canada) Ltd. holding 10%. Bullmoose Operating Corporation will be the manager and operator of the project. This paper will broadly cover the history and exploration work on the property, the geology, open-pit mining plans and equipment, the preparation plant flowsheet from breaker station to clean coal silo, the 35 km highway truck haul, the railroad loadout system, manpower requirements, approvals and permits, and general financial arrangements. Introduction The Bullmoose Mine Project is located about 87 km by road south of Chetwynd, B.C. and consists of an open-pit coal mine, a plant facility in the Bullmoose Creek valley below the mine, and a separate rail loadout facility on the British Columbia Railway Branchline near the new town of Tumbler Ridge some 35 km by road to the east. The plant will be capable of producing a total of 2.3 million tonnes per year (mty) of washed metallurgical and thermal coal. Long-term metallurgical coal contracts for high-quality, medium-volatile, bituminous coal have been signed with nine Japanese buyers for 1.7 mty, and the balance of0.6 mty will be for thermal coal production. Plant construction began in the spring of 1982, and in May 1983, preproduction waste and overburden removal in the mine was started. The plant began tuning up in October and was fully operational by December 1983. Metallurgical coal began moving to the coast in unit trains during November, and first vessel loading at the Ridley Island port began in late December 1983."

Jan 1, 1985

By B. Surender Mohan

Mining lignite pollutes the environment and causes ecological damage if unattended. Being conscious of the importance of environmental resources for the well-being of the living system, the Neyveli Lignite Corporation (NLC) adopts the policy of environmental regeneration as the foundation on which productivity is built. NLC started investing on Eco Care and Environment Protection long ago and it continues. Early investment in environmental protection has resulted in steady growth of the Company along with a healthy environment. The future vision of NLC is to be in the vanguard among the contributors to the community, environment and the nation by developing and utilizing industrial and human resources to the optimum. Untiring efforts are being put in mines (NLC as a whole) to maintain and sustain the ecological balance arising due to continuous mining activity. NLC?s Environmental Management System is becoming a symbolic role model for many of the opencast mines in Southeast Asia. NLC has been bestowed with number of prestigious Environment and Sustainability awards in recognition of the mammoth contribution in maintaining a clean and green environment.

Aug 1, 2013

By Guy Archambault, Réal Daigneault

"Un trait marquant du cadre tectorwstratigraphique de la Sous-province de l'Abitibi est la présence de nombreux couloirs de déformation d’extension régionale et sub-concordants au grain stratigraphique. La présence de grandes masses granitoïdes qui perturbent l'allure du grain tectonique est typique de la partie nord de la Sous-province de l'Abitibi. Des rides E-W constituées de complexes plutoniques précoces forment des reliefs structuraux agissant comme des moles résistants qui interfèrent avec la déformation régionale.Deux types de couloirs de déformation sont distingués, les couloirs de bordure et les discontinuités structurales. Les couloirs de bordure représentent des auréoles de déformation élevée qui s’accompagnent généralement d’un métamorphisme au faciès amphibolite. lls suivent /'interface entre les roches granitoïdes et les assemblages supracrustaux. Ces couloirs sont de puissance kilométrique et sont confines, surtout au sein des roches vertes, a l’interface des complexes granitoïdes d’importance. La limite entre la Sous-province de l'Opatica et les roches supra crustales de l'Abitibi est caractérisée par un important couloir de bordure issu possiblement d'un chargement tectonique irrégulier et concentre lors du raccourcissement horizontal.Les discontinuités structurales sont des failles ductiles qui se propagent surtout en direction E-W mais avec des variantes de directions SE et NE. Les discontinuités E-W se caractérisent par la présence d'une linéation d'étirement à fort angle de chute. Les discontinuités SE sont caractérisées par des linéations d'étirement horizontales et directionnelles et les mouvements observes sont system attiquement dextres. Les discontinuités NE sont des failles à comportement beaucoup plus fragile et se distinguent par des composantes de mouvement senestre. Elles sont tar dives par rapport aux discontinuités E-W et SE et ne représentent pas la symétrique du système SE.La combinaison des systèmes E-W et SE décrit un motif anastomose a l' échelle régionale. Les failles ductiles se rejoignent defaçon asymptotique, isolant des blocs peu ou pas affectes par la déformation. L'anastomose est un phénomène qui se produit a toute échelle et est reliée principalement aux Mt érogénéités et aux anisotropies 1) des forces agissantes (champs de contraintes régionale et locale) et 2) de la réponse del' empilement supra crustal (compositions différentes, fabrique initiate, propriétés mécaniques variées, niveaux d'altération).Dans le but de respecter un raccourcissement horizontal N-S, différents modelés sont proposés; ils mettent en cause soit une transpression dextre, soit des failles inverses réactivées en failles décrochèrent dextres soit des failles de chevauchement redressées."

Jan 1, 1990