Search Documents

By W. T. Martson

ABSTRACT Sooner or later, every producing mine faces the question of fill. This paper invites consideration of mill tailings as an economical, efficient, and quantitatively adequate source of such fill. Some of the advantages, disadvantages, methods of utilization, and methods of treating mill tailings for sand recovery are covered. ADVANTAGES AND DISADVANTAGES OF SAND FILL DISREGARDING economic com-promise, that material which supports the greatest applied load with the least compression is the best choice for fill. Table I, reproduced from U. S. Bureau of Mines Bulletin 60, is offered as evidence of the adequacy of hydraulically placed sand. Table II gives the results of tests made in an effort to determine the reason for the difference between load hearing qualities of dry-placed and hydraulically-placed sand. From these, it would appear that hydraulic placing gives a denser initial packing, with corresponding higher, and faster development of, load bearing qualities. Assuming this to be true, then if sand from mill tailings can be placed underground economically, it is the superior fill material. Table III summarizes cost data available. The most cursory glance through the available references (2, 5, 6, 7, 8, 9) will show .that the major benefit from the adoption of sand fill is a decrease in the non-productive fill ?cycle of a working place. This, it is estimated, increases the output of an individual stope by from 25 to 50 per cent. The advantage of reducing the number of required working places for a constant daily production is obvious.

Jan 1, 1951

By David G. Meadows

During the last decade Antofagasta Minerals? Los Pelambres Mine has dramatically increased its ore throughput following the fast initial phase ramp up through a series of planned incremental expansions. The original 85,000 mtpd, two SAG line plant was commissioned in 1999 and rapidly exceeded nameplate tonnage in only a few months. Following this, the inclusion of a pebble crushing circuit resulted in throughputs in excess of 114,000 mtpd and a recent, final third line SAG and ball mill addition have taken the plant to over 175,000 mtpd even with increasing ore hardness and changing ore feed characteristics. The progressive changes are described in this paper together with how the technical challenges have been met.

Jan 1, 2012

By Paul W. Billwiller

Introduction In 1937, the Britannia Mining and Smelting Company, Limited, was carrying on an extensive exploratory diamond-drilling programme. Most of this drilling was done on the 4100 level, the lowest working level in the mine. One of the exploratory diamond-drill holes, at approximately 12,500 feet from the portal of the tunnel, encountered heavily mineralized stringers of chalcopyrite and sphalerite in silicified grey schist. The mineralization was encountered just to the hanging-wall of the green mottled schist at a point 350 feet south of the 4100 tunnel. To delimit this new orebody, drifts and cross-cuts were driven on 3500, 3800, and 4100 levels to the hanging-wall in the area of the projected mineralization. On the 3500 level, the top of the mineralized zone was encountered. The zone was thoroughly explored by drifting and diamond drilling. The mineralization, however, was not sufficiently concentrated to be of commercial grade. On the 3800 level, the zone was found to consist of disconnected stringers of chalcopyrite and pyrite. Drifting was continued to the west and a long lens-shaped area of grey schist containing fairly heavy stringers of chalcopyrite was delimited. This lens later proved to be very close to the top of the commercial mineralization of the No. 8 orebody. On the 4100 level, a diagonal cross-cut was driven to the footwall of the downward projection of the mineralized zone. Diamond-drill holes from this cross-cut indicated a zone of heavy mineralization. A drift was driven off the cross-cut parallel to the zone and some distance to the footwall of it. Further diamond drilling disclosed a mineralized zone approximately 300 feet long and 35 feet wide containing sphalerite, chalcopyrite, and pyrite. The foregoing development work indicated a fairly large lens of mineralization of sufficient concentration to be classed as ore between the 4100 and 3800 levels. To explore this mineralization at depth, long diamond drill holes, dipping at minus 57° and minus 80°, were planned from some point to the hanging-wall of the orebody. The 4100 level was not suitable for small development headings, due to wider gauge track and larger cars than on the levels above. Therefore, a raise was driven from the diagonal cross-cut on the 4100 level to a point some 70 feet above and just inside the footwall of the orebody. From the top of the raise, drifts were expanded east and west to delimit the ore zone. In addition, a long cross-cut was driven 350 feet to the hanging-wall, and drifts were opened east and west from the end of the cross-cut to provide diamond-drill stations for the exploration of the orebody at depth.

Jan 1, 1946

By E. E. Cudby

"FOLLOWING the Leduc discovery •by Imperial Oil in 1947, The California Standard Company began to acquire land in the area immediately west of Edmonton and in line with the Leduc reef trend (Figure 1).The California Standard Winter-burn Province No. 1 in Lsd. 10, Section 4, Township 53, Range 25, West 4th, which was spudded, on the basis of a seismic anomaly, in December, 1949, failed to find reef. This well was located on the eastern .edge of a large land block which California Standard and Imperial Oil had pooled as a joint venture, with California Standard a:s the operator (Figure 2).The culmination •of an extensive exploration and land aquisition programme was the drilling of the California Standard-Acheson Province No. 1 well .in Lsd. 13, Section 2, Township 53, Range 26, West 4th. On August 24th, 1950, a drill stem test was run in the D-3 zone which had been encountered at 4,969 feet, and a flow rate of 702 barrels per day •of 36° gravity oil was obtained. Just previously, Imperial Oil had completed a similar programme in the Stony Plain Reserve with the swabbing-in of Imperial Stony Plain No. 1. These two discoveries set off a drilling programme to determine the extent and value of the oil accumulation.Subsequent drilling of wells some successful .and others not by several other companies as well as California Standard bias, .to date, still left much to be determined as to the approximate delineation of the productive limits of the Ache-son-Stony Plain area. However, to August 31st, 1951, there were twenty-one D-3 producers north of the reserve and three in the Stony Plain Reserve."

Jan 1, 1952

By Maureen McGuiness

"The pastefill circuit at the Bell Allard Mine in Matagami, Quebec started up in August 1999. The surface pastefill plant produces a cemented paste which is sent underground by gravity through a vertical pipeline in the mine ventilation shaft. Difficulties with paste flow during the start-up highlighted the importance of understanding paste rheology and the effect of operating procedures on line wear. By June 2000, the original circuit had been modified to include a paste pump to transport the paste to the shaft.The steps taken during the paste plant commissioning are discussed. The final flow sheet is presented, focussing on the use of instrumentation to ensure full column flow and proper distribution underground. Resistance modelling and accelerated curing of samples are examined as possible ways of predicting paste resistance to ensure compliance with the mine’s paste specifications.INTRODUCTIONCommissioning a new plant can be difficult and time consuming. The start-up of Noranda’s Bell Allard paste backfill plant was no exception. Since the first day it went into operation, the paste circuit could not meet the tonnage and paste quality requirements of the mine because the paste would not flow by gravity into the vertical pipeline in the mine’s ventilation shaft.Diagnosis of the pastefill problems proved difficult. It was only when the rheology of the Bell Allard paste was understood that the flow problems were solved. To ensure that the paste placed in the stopes meets mine requirements, two methods of paste resistance prediction are being developed."

Jan 1, 2002

By F. C. Lendrum

Introduction The property of Normetal Mining Corporation is in Desmeloizes township, Quebec, twelve miles north of Dupuy on the main line of the Canadian National railway from Quebec city co Cochrane, Ontario. The ore bodies occur within a band of highly sheared and sericitized agglomerate which strikes N.60°W. and clips 82° north. Along a zone 1,000 feet or more in length and of variable width, the agglomerate has been replaced by copper, zinc, and iron sulphides, with copper usually predominant on the hanging-wall side and pyrite replaced in part by sphalerite on the footwall. A northsouth diabase dyke cuts through the ore zone near its east end. The Normetal mill produces a copper concentrate and a zinc concentrate which are shipped, respectively, to Noranda, Que., and Newcastle, Penn., U.S.A., for further treatment. The present paper deals with the milling of ore from what is known as No. 3 orebody. This is a lenticular body of high-zinc ore lying co the east of the diabase dyke, along the line of strike of the main ore zone, which extends westward from the dyke. On its northern side, No. 3 orebody is in contact along most of its length with a narrow band of copper ore which is highly oxidized.

Jan 1, 1948

By J. G. A. Stevenson

"IntroductionDURING the past quarter of a century diamond drilling, in all its phases, has increased in Canada to a very impressive total of more than 10,000,000 feet annually. Since the art of diamond drilling became recognized, some seventy-five years ago, there has been considerable improvement in both equipment and technique. The steam-powered drill rig and the hand-set diamond bit are things of the past.The purpose of this paper is to review some drilling trends •and practices over the past few years. In the preparation of the paper, the author wishes to acknowledge kind assistance of Mr. J. D. Cumming, Dr. C. H. Hitchcock, Mr. Robert H. Quintal, and many others, including staff members of the Longyear organization.Figures provided by the Dominion Bureau of Statistics for the year 1954 show that Canadian production of metallic and non-metallic minerals and structural materials had a value of $1,454.2 million, excluding radioactive products for which figures are not available. Approximately 61 per cent of this valuation comprised production of nickel, copper, gold, coal, asbestos, zinc, lead, and iron. It is certain that diamond drilling played a major role in the discovery and development of the orebodies from which these minerals were obtained.After the surface examination of an ore deposit, diamond drilling will automatically follow, in order to determine structure, grade, and tonnage.Footage drilled by mining companies and contractors on mineral exploration and blast-hole work since 1945, as reported by the Do-minion Bureau of Statistics, is shown in Figure 1."

Jan 1, 1955

By Hang Zhao, Xinping Li, Pingan Wu, Yi Luo

"The deep-buried rock surrounding the Jinping II Hydro-power Station was taken as the engineering background. Using model specimens of classified rock materials to simulate fractured rock mass under high in-situ stress conditions, the test about acoustic propagation law on single fracture model of specimen under different pressures and different angles were carried out. The variation of p-wave velocity in fractured rock mass and axial stress-strain relationship in the whole test procedure was also studied. Based on damage mechanics principle and the acoustic wave propagation in cracked rock mass, comparative study on damage constitutive relation of fractured rock mass under high in-situ stress in consideration of equivalent strain and equivalent energy was performed. As the results showed, with the change of axial stress level under constant confining pressure, the change in wave velocity can be divided into three stages: slow increase (small variation in amplitude), rapid reduce (large variation in amplitude ) and accelerate reduction. When the confining pressure is constant, the maximum p-wave velocity and the peak strength of specimens increases with the decrease of the crack angle.When the crack angle is constant, the maximum p-wave velocity and the peak strength of specimens increases with the increase of confining pressure.It is identified that the theoretical calculation results of constitutive relation about elasto-plastic damage model containing variable wave velocity in the fractured rock mass is consistent with the model test results.Therefore,the constitutive relation can provide reasonable suggestions for engineering practice. INTRODUCTIONThere are a lot of joints and fractures in surrounding rock mass of deep-lying in the Jinping-II hydropower station, which has a great influence on the physical and mechanical properties of rocks and effects the acoustic wave propagation and attenuation law in rock. Many previous research and project examples has proved that sound propagation parameters are closely related to crack and stress condition. Thus, it has certain theoretical significance and practical application value to carry out researches on sound propagation characteristics and establish damage constitutive model of fractured rock mass which is related to sound propagation parameters."

Jan 1, 2015

By G. Graves, J. A. Walker

"Abstract - The Mount Fronsac North volcanogenic massive sulfide deposit is the most recently discovered massive sulfide body in the Bathurst Mining Camp. The deposit occurs within a sequence of intercalated fine-grained felsic tuff and sedimentary rocks (Little Falls member), at the top of the Nepisiguit Falls Formation. Aphyric to sparsely feldspar-phyric rhyolite and related volcanic rocks of the Flat Landing Brook Formation overlie the host sequence. The massive and semimassive parts of the deposit have a north-south strike length of 525 m and a dip of ~45°E; the deposit is continuous downdip for 600 m, and thickness varies from 2 to 20 m. The deposit contains an estimated geologic resource of 14 Mt of low-grade, semimassive (>60%) to locally massive sulfides, and includes a high-grade zone of 1.26 Mt grading 7.65% Zn, 2.18% Pb, 0.14% Cu, 40.3 g/t Ag, and 0.40 g/t Au. The semimassive to massive sulfide intersections occur in an envelope of quartz-sericite±chlorite schist, which is interpreted to be intensely deformed felsic tuff. This sequence has a maximum thickness of 140 m and contains significant (up to 50%) fine- to coarse-grained disseminated pyrite. The pyritic envelope has a strike length of 900 m and extends over 1000 m downdip. Massive sulfides are found throughout this alteration envelope, but more commonly occur at or near the upper contact. The significance of the discovery of this deposit is that it represents a near surface discovery of a large tonnage sulfide body in a mature mining camp, one in which the possibility of discovery of a new shallow deposit had been all but discounted. This opens the possibility for future discoveries in this part of the Bathurst Mining Camp. Sommaire - Le gîte de sulfures massifs volcanogènes du Mont Fronsac Nord est la découverte de sulfures massifs la plus récente dans le Camp Minier de Bathurst. Le gisement est situé dans une séquence de tufs felsiques à grains fins interlités de roches sédimentaires (membre de Little Falls, au sommet de la Formation de Nepisiguit Falls. La partie massive et la semimassive s’étendent du nord au sud sur 525 m et ont un pendage de ~45°E; le gisement est continu sur 600 m en angle de chute et son épaisseur varie de 2 à 20 m. Le gisement contient une ressource géologique évaluée à 14 Mt de sulfures semimassifs (>60%) localement massifs à basse teneur, incluant une zone à haute teneur de 1.26 Mt titrant 7.65% Zn, 2.18% Pb, 0.14% Cu, 40.3 g/t Ag, et 0.40 g/t Au. Les intersections de sulfures semimassifs à massifs se situent dans une enveloppe de schiste à quartz-sericite ± chlorite interprétée comme un tuf felsique intensément déformé. Cette séquence contient une quantité importante (jusqu’à 50%) de pyrite disséminée dont le grain varie de fin à grossier et son épaisseur maximale est de 140 m. L’enveloppe pyriteuse s’étend latéralement sur 900 m et a été tracée jusqu’à 1000 m en angle de chute. Des sulfures massifs sont trouvés partout à l’intérieur de cette enveloppe d’altération, mais ils sont plus fréquents près du contact supérieur. L’importance de cette découverte tient à ce qu’elle est un exemple d’un gisement à fort tonnage nouvellement découvert à une faible profondeur dans un camp minier mature, i.e., un camp ou l’on ne croyait plus qu’il était possible de trouver un gisement près de la surface. Ceci ouvre la porte à la possibilité d’autres découvertes dans cette partie du Camp Minier de Bathurst."

Jan 1, 2006

By John C. Taylor

A resource document, prepared for the Royal Commission on the Health and Safety of Workers in Mines, which outlines aspects of occupational health and safety in the Canadian metallurgical industry has been expanded to provide examples of some practical solutions. General process descriptions are provided in conjunction with some of the major potential hazards associated with each step. Emissions to the working environment, particularly around converters, are discussed. Newer metallurgical processes, the role of automation and other advances in the metallurgical industry are described with respect to their impact on the work place. The role of staff and unit employees in providing safe working conditions in the complex metallurgical plant of today is outlined and the need for close cooperation within the human sector emphasized. The technology is available and is being applied to integrate the complex process requirements with realistic regulations to control emissions and provide a safe, healthy environment in metallurgical plants.

Jan 1, 1978

By S. Amira

The corrosion behavior of high pressure die-cast and thixocast AXJ530 magnesium alloys has been investigated in 0.05M NaC1 solution at pH 6.0 using potentiodynamic polarization tests, electrochemical noise (EN) technique, electro-chemical impedance spectroscopy (EIS) and scanning reference electrode technique (SRET). The behavior of die-cast and thixocast specimens were compared using each of these techniques and the results discussed. Further tests have been carried out with die-cast AZ91D alloy to better compare and interpret the results. Experiments indicate that the thixocast specimens of AXJ530 alloy have a better corrosion resistance than those of die cast alloy in neutral solution.

Jan 1, 2006

By Raymond S. Suglo

Increasing depths of mining coupled with the mechanization of most underground mining operations have led to growing complexities in the mine environments with the production of large amounts of gaseous and particulate contaminants. Over 100,000 lives have been lost due methane gas and dust explosions in coal mine workings in both the US and Canada since 1900 when the methane concentrations exceeded stipulated levels in some workings. There is therefore the need to constantly assess and evaluate the performance of the existing mine ventilation systems to maintain safe and acceptable mine environmental conditions in workings to meet the requirements of federal, state or provincial laws. This paper uses the results of continuous monitoring of methane concentrations conducted in selected development headings in coal mines in North America to assess the effectiveness of existing auxiliary ventilation systems in the control of methane gas concentrations in the headings. The results show that the average quantities of fresh air required to dilute, disperse and remove methane concentrations within set levels of one minute varied from 5.43 m3/s in Heading #11 (Condition 2) to 27.97 m3/s in Heading #10 (Condition 1) and this represented about 12 to 26% of the quantities required to dilute methane concentrations to safe levels within one minute under Condition 1 and 32 to 139% under Condition 2. The average dilution times in the headings studied were less than 8 minutes. The forcing efficiencies of the auxiliary systems in the headings studied ranged from poor to excellent implying that the auxiliary ventilation systems were capable of controlling the methane concentrations below statutory levels but may not be able to cope with large and unusual methane concentrations in the headings. This study is important to prevent methane gas and coal dust explosions in coal mines and thus avoid any loss of lives and property.

May 1, 2001

By W. J. Tough

THIS paper offers examples of some of the typical calculations which occur in the ventilation of metal mines. The fi.rst section of the paper discusses the problems associated with natural-draft pressure; the second section presents the more common of the calculations concerned with the operation of mine fans; the third section illustrates the integration of the individual problems covered by the preceding sections into the larger problem of determining the operating characteristics of a fan for a particular mine duty. There is a very definite limit to the extent to which pure arithmetic can be successfully applied to the solution of min<; ventilation problems. As mines advance from the exploration, development, and initial production stage to the rime when underground workings become exceedingly complex, there is a considerable increase in the relative importance o theory and judgment in the solution of ventilation problems. These calculations illustrate the application of mathematics to ventilation, but they also in-elude examples of instances where arithmetic cannot be conveniently applied, and important estimates, based on judgment compounded of experience and a knowledge of the theoretical consideration involved, must be made. The inclusion of such estimates is intended as a guide and a warning to the reader; a guide in assisting him to recognize and estimate his own incalculables; and a warning that the solutions must not be blindly applied to his apparently similar problems. These sample calculations are intended to assist the reader in applying the theory contained in the standard texts on metal-mine ventilation. They have been selected from the ventilation experience of a British Columbia mine.

Jan 1, 1942

By C. Rodgers, E. (Ted) Warren

"LocationThe Key Lake operation of Cameco Corporation is located at latitude 57°N in northern Saskatchewan, within the southem boundary of the Athabasca formation. The nearest city is LaRonge, located 240 km to the south. Access to the mine is by all-weather road and by private airstrip.Description of OperationThe mill was designed to produce twelve million pounds of uranium oxide (U3O8) a year from a feed grade of 2.4% U3O8. Current production is fourteen million pounds from 2.0% feed.Following grinding, the uranium is leached using sulphuric acid and oxygen in autoclaves. An eight thickener counter current decantation (CCD) circuit is used to separate the uranium-bearing solution from the solid waste residue. The uranium in solution is further purified in a solvent extraction circuit. The purified uranium is then precipitated using ammonia, calcined at 840°C, and packaged in drums for shipping to refineries. There is a crystallization circuit to recover excess ammonium sulphate produced in the process, and a waste treatment circuit.HistoryUranerz Exploration and Mining discovered the Gaertner and Deilmann orebodies in 1975 and 1976, respectively. Between 1975 and 1977, Uranerz conducted laboratory studies and delineated a process for the Key Lake ore known as the ""Bonn process."" In 1977, Sherritt Gordon Mines Ltd. was retained to conduct further studies in cooperation with U ranerz. The technical feasibility of the Bonn process was generally confirmed. Howeve1~ alternative processing methods also appeared feasible, and over the period 1978-1979, a detailed research and development program was conducted to finalize the processes to be used and to provide data for design of the plant."

Jan 1, 2000

By G. E. Norman, A. L. Mckague

"The new smelting process commenced operation in 1978. The pelletizing and sinter plants were replaced with slurry-fed roasters and the blast furnaces with electric furnaces. The existing converter aisle and matte handling facilities remained unchanged.Process DescriptionNickel-copper concentrate is partially roasted in two slurry-fed fluid bed roasters. After gas cleaning, the sulphur dioxide gas is transferred to the acid plant. The roaster product is conveyed to two electric furnaces for smelting to produce a waste slag and furnace matte. The slag goes to the disposal area and furnace matte containing the metal values is processed in the converters for further removal of iron and sulphur.The final matte containing about 75 per cent metal values is shipped to the refinery in Norway.The commercial smelter was designed for 2135 tonnes per day of concentrate, with an availability of 85% . Roasters and electric furnaces were sized at 117 per cent of design, or 1250 tonnes per day on each of two lines. Concentrate storage capacity in the plant is sufficient for two to three days&apos; plant operation.The new smelting process will be discussed under the following headings:Concentrate Slurry HandlingFeed PreparationRoaster OperationRoaster Gas CleaningCalcine TransferElectric Furnace Operation and Process Control Converting and Matte HandlingUnder these headings, process control , equipment changes, and plant performance after three years&apos; operation is reviewed. A brief discussion of accident prevention , and working environment is also included ."

Jan 1, 1984

By Gavin A. Hunt

In order for mines to operate profitably throughout their life it is important to monitor and maximise ore recovery. A common problem facing many mines is the underestimation of clay type and its distribution in ore at the mine face, blast hole or in the ore stockpile. Too much clay entering the heap leach ore stream for example causes a dramatic reduction in heap leach efficacy and or increased leaching times. The end result is poor leaching performance and much reduced metal production. Poor clay identification and quantification is attributable to many factors, including costly and slow off-site mineral analysis techniques, such as XRD, XRF and petrology, the visual and subjective limitations of the core logging geologist and a lack of suitable low cost, high throughput mineral logging instruments. To get round these problems a new, non-contact, imaging spectrometer - the SpecCam - was developed by Spectra-Map Ltd, to allow high throughput identification and quantification of minerals from mineable material. Its novel imaging design can collect millions of data points (pixels) per day; each pixel contains spectral information that allows a wide variety of mineral types, including the smectite and illite clays, and phyllosilicates such as talc and kaolin, to be identified. Because all the ore can be imaged a much more reliable mineral log can be made. Hence, mapping changes in mineral composition - related to variations in phenocrysts, macrocrysts, veining or wall rock - is possible. Examples of SpecCam data from Goldfields Cerro Corona Porphyry stockpile and from Rio Tinto?s Argyle Diamond mine illustrate the mineral identification and quantification capabilities of the SpecCam. More importantly, for the first time very accurate % abundances for the different minerals can be obtained using an image-based modal count technique. The modular design of the camera, plus its extremely flexible high speed filter, mean that the SpecCam can be easily installed on different equipment, each one suited to different ore recovery problems. For example the SpecCam can be used on an automated portable logging frame to measure drill core, RC chips, hand samples or powder, or alternatively installed on a Geotek multi-sensor core logger for high-throughput, automated logging of drill or blast hole core using co-registered multi-sensor data. An exciting recent development has been the installation of the SpecCam on CommoDas ore sorting equipment, used around the world for 24 hour mill-feed monitoring and automatic ore sorting. Real-time ore sorting decisions can be made as material is monitored on a conveyor belt running at 3m s-1, from which the ore can be automatically sorted into high-grade, low-grade or waste streams for example. The three installation options for the SpecCam mean that most mineral analysis and automated core logging or ore monitoring needs can be met at the mine. For the first time rapid and automatic mineral identification and accurate quantification can be made. All of which allow the mine geologist or metallurgist to make important decisions about maximising the metal recovery process.

May 1, 2007

By J. A. Relf

The construction of refineries and gas conservation plants in the general Edmonton area in the early 1950's made available large quantities of by-product liquified petroleum gases (LPG). These gases, together with discovery of increasing reserves of natural gas in the Edmonton area, provided Canadian Chemical Company with two of the necessities for petrochemical production, namely, available and reasonably priced raw materials and fuel. This paper outlines the development of the $83 million Edmonton plant from its origin, together with a brief description of the processes and some of the interesting features involved. Several economic aspects of the petrochemical industry are high-lighted including its importance to the local community and the province. The paper reviews the relationship between the oil and gas industry and petrochemical manufacturing and indicates some of the factors that may affect the future growth of the petro-chemical industry in Wes tern Canada.

Jan 1, 1962

By Hamidreza Soltanzadeh

The injection of CO2 into a reservoir or aquifer can potentially result in deformation, induced fracturing and fault reactivation in the injection zone and/or the rocks that surround it. This paper reviews the data collection and geomechanical analyses performed to assess these potential hazards for the Heartland Area Redwater Project (HARP), in which CO2 sequestration is being considered in a carbonate (Leduc Formation) reef. A three-dimensional mechanical earth model (3D MEM) was developed using available geophysical log data from several wells. The geomechanical response to CO2 injection was studied using a finite element numerical model based on the 3D MEM and pore pressure distributions predicted using a reservoir simulator. The modeling results suggest that the potential for induced fracturing and fault reactivation is low and the maximum predicted ground surface heave is less than 2 cm. Sensitivity analyses conducted with a 2D geomechanical model that was extracted from the 3D model confirm that this conclusion holds true even when a reasonable measure of uncertainty in rock mechanical properties, ambient pore pressures and horizontal stress magnitudes is accounted for.

Jun 1, 2012

By B. Erdem, N. Çelebi

An important problem associated with tandem dragline systems is that of matching the productive capability of individual draglines in the combination. In this paper, a dependence mechanism among draglines in a tandem system is described, and possible consequential problems in a poorly-matched system are defined. The rate of linear advance and the cost of stripping are determined as two major indications for an efficient operation. The proposed decision criteria and the underlying mechanism to select a synchronous couple are introduced and used in simulating tandem dragline systems. The developed model is tested on a hypothetical strip mine where pullback stripping is applied with a tandem dragline system.

Jan 1, 1999

By Y. Huang

Corrosion of GaAs in aqueous electrolytes is a major limitation in implementing GaAs-based photoelectrochemical solar energy conversion systems, In this work, the corrosion behavior was investigated by electrochemical methods and surface analysis approaches, in both H2SO4 and NH3?H2O solutions, Open-circuit measurements showed that the cleaned GaAs surface was very sensitive to water/air, Impedance measurements for n-GaAs showed that an inductive loop only appeared at a high corrosion rate because a reaction intermediate is the oxidant for a further decomposition step in combination with chemical reaction with water, The results suggest that the same corrosion/decomposition mechanism occurred on n-GaAs in the two solutions, When the surface-hole concentration was low, the hole injection or generation process was the rate-determining step, At large reverse bias on n-GaAs, with high-hole concentration, the corrosion rate was limited by a Faradaic adsorption process, involving an adsorbed intermediate, The different surface compositions after corrosion in the two solutions can be explained by the dissolution of As(0), Further oxidation of As(0) to As(III) in NH3?H2O solution is still slow, as suggested from X-ray photoelectron spectroscopy (XPS) analysis,

Jan 1, 2005