Search Documents

By S. Bastola, Y. P. Chugh

"This research determines shear strength and stiffness properties of bedding planes and joints in the roof strata rocks within 7.5 to 9 m (25-30 ft.) overlying the Illinois #6 coal seam (within the pressure arch zone). A shear test loading device was designed into a 1.334 kN (150 t) Forney Compression Loading Machine to perform direct shear tests in accordance with ASTM D5607-08 “Standard Test Method for Performing Laboratory Direct Shear Strength Tests of Rock Specimens under Constant Normal Force”. The data were used to determine peak and residual friction angles and the dilation angle. A total of 49 bedding plane samples were tested, out of which 46 (36 intact and 10 relatively weak and loose) samples passed QA/QC procedures in accordance to ASTM D5607. Samples from eight (8) different bedding planes- shale/limestone (SL), shale/sandstone (SSs), shale/bone (SB), laminated sandstone (LS), shale/shale (SS), bone/bone (BB), bone/limestone (BL), and limestone/limestone (LL) were tested. The number of samples tested for each bedding plane were: SL- 11, SSs- 8, SB- 5, BB- 4, LS- 6, SS- 9, BL- 1, and LL- 2. Peak and residual shear strength values at 2.75 MPa normal stress range 1.06 – 6.26 MPa and 0.82 MPa to 0.82 – 4.14 MPa, respectively. The average normal and shear stiffness values are about 11.98 GPa/m and 3.11 GPa/m. Dilation angles are low (<10?) and negative in some cases. Angle of sliding friction values range from 9? to 42?. Joint Roughness Coefficient (JRC) values were less than 10.INTRODUCTIONRock mass may be defined as the total in situ rock medium containing bedding planes, faults, joints, folds and other structural features. Therefore, it is discontinuous and may have heterogeneous and anisotropic engineering properties. Upon creation of an excavation in a rock mass, bedding planes and joints are the most likely points of failure initiation. The failure typically occurs either in tensile or shear mode. Upon failure initiation stresses are transferred to the neighboring rock mass and the failure progresses until stability is achieved through equilibrium of stresses and strength. An example of this mechanism is development of the pressure arch. This study determined the shear strength and stiffness properties in shear and compression of bedding planes and joints in the immediate roof strata rocks within 7.5-9 m ( 25-30 ft.) overlying the Illinois No. 6 coal seam (within the pressure arch zone). Since such data are currently not available for Illinois Coal Basin mines, researchers and engineers have been using estimated values for design purposes. The immediate roof lithology in the proposed mining area consists of shale 0.62 m; Bone 0.09 m (0.3 ft.); Limestone, 0.10 m (0.33 ft.); Shale 2.37 m (7.9 ft.); and sandstone 0.55 m (1.83 ft.). The bedding plane samples were provided by a mine in south-eastern Illinois operating at a depth of about 180 m (600 ft.)."

Jan 1, 2015

By E. Howard Lambert

"Operating costs of mining plants are increasing due to the increased cost of labour, materials and fuels. Labour and materials costs are factors not readily controlled. However, the use of energy from fuels may be controlled by plant operations. This paper describes the fossil fuels, their expected rate of depletion and their costs. The paper considers methods which may be used to provide an efficient use of energy from fuels. It includes an outline of obtaining energy, as heat, from mine milling operations (air compression) and obtaining the maximum use of energy from fuels used to generate electricity."

Jan 1, 1973

By A. Torkian

Process water from production of concentrates in Meydook copper sulfide mine is transferred to the 8.3 million m3 tailings dam and a water retention pond after initial thickening. Elevated concentrations of heavy metals, sulfate, and TDS and decrease in pH as well as seepage into the aquifers have been the concern of the regulatory agencies since the start of activities. In this paper the results of a 6-month monitoring program from 4 wells are presented. The wells were located approximately 1.5 km from downstream of tailing dam (0.4 km from water retention pond) as well as upstream background well (2.28 km from water retention pond and 1.27 km from tailings dam). The objective was to study possible effect of accumulated tailings on the groundwater resources. Water levels in sampled wells were on average between 20 and 40 m. Results showed high levels of lead (5 ppb), copper (0.17-0.46 ppm) and selenium (73.1- 29.1 ppb). High levels of selenium and lead were partly due to natural geological settings of the area with high levels present in unaffected soils in the vicinity including water wells of villages upstream of mining operations. High copper levels were attributed to both mining operations as well as deposition from particulate air deposition onto the soil and transport to ground water by rain.

Aug 1, 2013

By C. O. Swanson

"OUR INTEREST in estimates of world reserves of lead and zinc is focussed mainly on the information they give about the sufficiency of metal supplies for the future. However, we soon realize that the estimates can be interpreted in several different ways. Accordingly, it is necessary to have some under-standing of the elements represented by a compilation of world re-serves, and we will start by examining the accuracy of the estimates and what they attempt to measure.Variations in Estimates of the ReservesIf we study the estimates of world reserves that have been published in recent years, we note immenediately that they vary over a considerable range. For example, an article by Shea in 1947 gave world reserves as about 36 million tons of lead and 60 million tons of zinc. Shea did not in elude the United States but I have added to his totals the estimates made by the Bureau of Mines for that country in arriving at the foregoing figures. For approximately the same date, the American Zinc Institute and the Lead Industries Association reported world reserves as about 50 million tons of lead and 77 million tons of zinc. A comparison of the two sets of figures shows a mean variation of 30 per cent. For individual countries the difference between estimates can be even larger. A few years ago the estimate of Canada's reserves made by the United States Bureau of Mines was 7.4 million tons of lead and 14.0 million tons of zinc, while the Gordon Commission reported 1 O. 7 million tons of lead and 26.0 mil-lion tons of zinc. In this case the mean variation was 55 per cent."

Jan 1, 1960

By Robert B. Parsons

"For the fourth time in five years, residents of northern Canada have seen a change in the tax treatment of housing and travel costs. The latest changes announced in December 1990 by the Minister of Finance are to become effective in 1991. When will the tinkering stop?IntroductionFor man y years prior to 1987, certain travel and housing allowances received by employees in remote areas were generally considered by Revenue Canada to be tax-free, even though some observers suspected that such generous treatment was contrary to the provisions of the tax legislation. In the mid-eighties, Revenue Canada decided to reconsider the tax treatment of the mining industry&apos;s long standing practice of providing housing and travel assistance to these employees. The tax- free treatment was continued by virtue of annual remission orders, but only pending the enactment of legislation which would tackle the issue head-on and layout the rules in black and white to be seen by all. The sequence of events since then may be chronicled as follows:February 26, 1986-Finance Minister Wilson&apos;s budget present s the framework for the future tax treatment of travel and housing benefits provided to residents in remote regions of Canada.December 22, 1986-The Minister of Finance announces detailed rules to fill in the earlier announced framework.January 1, 1987-The new tax rules come into effect.April 29, 1988-The Minister of Finance announces the establishment of a Task Force to examine the existing criteria for determining the eligibility of residents of northern and isolated areas for tax benefits.October 27, 1989-The Task Force presents its report.December 7, 1990-Finance Minister Wilson announces a new system of tax benefits for residents of Canada&apos;s northern and isolatedregions.January 1, 1991-The new rules become effective."

Jan 1, 1991

By J. D. T. Steyl

Anglo American Corporation and the University of British Columbia have developed a medium-temperature oxygen pressure leaching process for the extraction of copper from chalcopyrite concentrates in an acid-sulphate system (AAC/UBC process). Leaching is performed at 150°C and surfactants are added to disperse molten elemental sulphur from the unreacted sulphide surface to prevent liquid sulphur occlusion. Copper extractions of over 95% and elemental sulphur yields of around 60% were observed over a 2-hour average residence time in a continuous pilot autoclave. Sporadic blockages occurring under continuous conditions were found to be caused by the accumulation of molten elemental sulphur mixed with unreacted sulphide mineral. A batch programme of experimentation was undertaken to establish the reason for this phenomenon. Batch experiments were conducted at low pulp densities on concentrate samples with narrow size distributions and at similar solution compositions to those experienced in the pilot autoclave. The overall rate of chalcopyrite oxidation was shown, under approximately constant solution composition, to be a strong function of the total available mineral surface area. Initial copper extraction rates followed the shrinking particle kinetic model under intrinsic surface control. Deviation from shrinking particle kinetics was however observed after a certain oxidation time. Secondary electron images identified small (typically less than 20 µm) sulphur conglomerates at the point of deviation, which &apos;collected&apos; unreacted chalcopyrite mineral particles and lowered the total mineral surface area available for oxidation. These sulphur clusters are thought to be the precursor for blockages experienced in the continuous pilot autoclave. These results emphasised the importance of fine grinding (P80 5-20 µm) and suggest that shorter residence times may minimise the formation of sulphur conglomerates in a continuous autoclave operating at medium temperature.

Jan 1, 2004

By W. van der Merwe

ABSTRACT With the gold industry processing more complex ores, the online measurement and control of cyanide addition to the gold leaching circuit has become more critical. This paper compares the two commonly employed ‘free’ cyanide online analysis methods (amperometric and potentiometric endpoint silver nitrate titration) with the rhodanine endpoint silver nitrate titration and ion selective electrode methods common at site laboratories. Measurement differences between these methods are presented and discussed for cyanide solutions containing copper and zinc with varying cyanide to metal ion ratios. The resulting cyanide available to leach gold is also compared using these measurement techniques.

Jan 1, 2013

By Maureen Jensen

For mining companies looking to establish a strong North American presence, raise their profile or finance and position themselves for future growth, there is no other destination in the world that can offer a mining company the same opportunities as Canada whether you are an established blue chip or promising junior. Despite historically poor world commodity markets and shaky investor sentiment towards junior explorers caused in part by fallout from the high profile Bre-X fraud, Canada continues to shine as the undisputed mining finance capital of the world. Our natural riches and mining history go a long way to explain Canada's international prominence in mining finance. Canada has actively created and maintained one of the most integrated national frameworks to support mining ventures of all kinds. Our diverse industry, from one-person grass-roots explorers to mining industry giants, is one of our main strengths whether your company is Canada-focused or internationally active. The mining industry continues to be a vital contributor to the Canadian economy, contributing $26.2 billion in 1997 or 3.8% of national GDP, and is the second largest earner of foreign exchange. Industrial mineral companies are a very important part of this strength. These companies require a continuing access to capital to ensure that they can continue to compete and the globalisation of the Canadian mining industry has affected this industry just as much as it has affected every other industry in Canada.

Jan 1, 2001

By J. H. Morrish

"The delivered price of any mineral is the determining factor in converting untapped resources into economic resources. Transporting the minerals from the mine to the market plays a significant part in the total package. The expansion of the Western minerals industry in the last ten years has been paralleled by improved transportation systems to reduce cost, increase accessibility of resources and get the minerals to market in the shortest time possible. A review is made of developments, such as unit trains, complex multi-modal systems and containerized transport, over the last ten years, with specific movement outlined. The total transportation package of land transport, port and terminal facilities, and water transport, where needed, is stressed. As the volume of minerals movement expands, increasingly sophisticated and integrated transportation systems will have to be utilized. The development of solids pipelines and other possibilities is outlined."

Jan 1, 1973

By H. R. Banks

"AbstractThe rod mill introduced into the Sullivan Concentrator flow in September, 1948, replaced two sets of 74 in. by 20 in. rolls and their accompanying screens. In addition to the work formerly done by the rolls, the rod mill is producing a finer product and one which provides more suitable feed for the primary ball mills. The object of the finer discharge from the •primary mills is to make possible a feed directly from the mills to a series of flotation machines where a large portion of the galena can be withdrawn from the circuit while the galena is still coarsely granular. The interposing of classifiers between grinding and flotation means the selective grinding of the galena.The author summarizes the work of •the rod mill through the first 5,000,000 tons and shows that the wear of lifters, liners, and rods is definitely below normal for the type and size of rock being handled. The rod mill, driven through a fluid coupling, has been subject to a range of speeds from 13.5 to 19. A pinion in the speed reducer was changed to allow the extending of the normal speed range of the fluid drive of approximately 4 r.p.m.Since the critical speed inside the liners •is 23.4, the range •in per cent of criticial is 57.7 to 81.2 per cent.The capacity of the mill increases with increasing speed but the character of the product remains approximately the same except when the feed rate is too high.Consumption of steel, power, and other operating data are presented.The author introduces certain fundamental observations on the principles involved •in comminution in order to support the special design and operation of the rod mill."

Jan 1, 1952

By Euler De Souza, J. Daniel Stinnette, Julian Varaschin

"This paper outlines some of the factors that affect the airflow required for the ventilation of modern diesel-powered equipment and of electric equipment and examines how they can be applied in determining reasonable ventilation rates for Tier IV compliant diesel equipment and for electric equipment operating in mining environments. Airflow calculations for modern diesel-powered equipment and for electric equipment are more complex and must be based on a combination of factors that are unique to each mine. Methodologies for ventilation rate determinations for each case are proposed in this paper.INTRODUCTIONTraditionally, airflow requirements for production and support equipment operating in underground mines have been determined by multiplying the vehicle power by a ventilation rate that was either mandated by regulations or determined empirically from known quantities. However, in light of the drastic reductions to diesel equipment emissions mandated by the US EPA Tier IV and EURO Stage 4 regulations, there is still a great deal of uncertainty in the underground mining industry among those responsible for the ventilation of planned new mines or the expansion of current mines. The question remains, what ventilation rates should the ventilation system designer apply for modern diesel equipment?Also, given the ongoing development of grid/battery-electric equipment and active construction of fully electric mines, it has become critical to determine adequate airflow rates per brake kilowatt of electric engine power. One of the most important criteria for determining ventilation rates for electric equipment is the amount of heat they generate, as this is the most significant emission produced by electric equipment (which do not produce exhaust gases or particulates). Therefore, ventilation rates required to dissipate heat from electric equipment must be suitably determined for all electric vehicle fleets operating in underground mines."

Jan 1, 2019

By A. Ignatieff

"Demonstrations of Automatic Coal Burning EquipmentAT THE 1951 and 1952 Annual Coal Research Conferences sponsored by the Dominion Coal Board and attended by delegates from the Dominion and Provincial governments as well as industry, the importance ,of encouraging the co-operative interest of Canadian coal and equipment industries in •promoting the use of equipment types best suited to burn given Canadian coals was emphasized. It. was suggested that this idea •be enlarged upon at forthcoming C.I.M. meetings that would be .attended largely by coal mining engineers.With this in view, a Domestic Heating Forum (1) was featured in the Coal Division programme at the 1951 Annual Western Meeting of the Institute in Calgary, and a much more ambitious programme, highlighted by live demonstrations, was •staged at the combined Annual Western Meeting and Fourth Meeting of District 4 held in Winnipeg in October 1952.With the excellent co-operation of a number of equipment manufacturers and coal companies, and with facilities kindly provided •by the University •of Manitoba authorities, burning demonstrations were• arranged in the Agricultural Engineering Building, on October l 7th. These demonstrations were a fitting sequel to the Coal Division sessions held in the Royal Alexandra Hotel on October 16th, at which the combustion of coal was specially featured in a series of papers by prominent Canadian and United States specialists.The primary purpose of the demonstrations was to •show that all coal, regardless •of rank, can be satisfactorily used provided that proper application is made with equipment suited to its purpose."

Jan 1, 1953

By Karl J. C. Harries

"6.1. INTRODUCTIONThis chapter comments on some of the more common types of agreements related to property examination and acquisition, other than the farm-in/joint venture agreement or common undertaking, which is dealt with in the next two chapters. Many of the comments made in Part IV of Chapter 4 apply equally to any such agreement. In addition, many of the comments in Chapter 8 and the examples in Volume II are most certainly relevant to many other types of agreement.6.2. RIGHTS OF FIRST REFUSAL1A right of first refusal is a right that obligates an owner to offer his property, or an interest therein, to the holder of the first right if the owner intends to sell or otherwise dispose of it. It may be triggered either by the owner wishing to offer his property for sale or by receipt of a bona fide offer to purchase his interest from an “outside” third party. The mechanics and procedures to implement a first right should be set out clearly in the agreement, and their basics are the same, whether the first right is a stand-alone document or is part of an acquisition agreement.2Rights of first refusal are common in agreements to permit some control over the disposition of an interest and there they can be a valuable provision. However, some explorationists feel that they are also a good stand-alone agreement to have while a property is being evaluated to decide whether or not it is worth optioning. The reasoning is that such an arrangement will tie up the property to allow a quick look and, if the property looks interesting, the balance of the term of the first right will give an ample exclusive period of time to negotiate with the owner and settle an acquisition agreement. In addition, the explorationist is protected by the first right if the owner decides to negotiate a deal with another party."

Jan 1, 2003

By B. Arlyuk

The complex system has been developed for long-term assessment of world prices and sale volume of primary aluminium when using the analytical model of the market and market supply forecasts as well as economy development in the Western countries characterized by the industrial production indices as correct data of Western World aluminium consumption are absent, The important part of this system is the model developed for forecasting the degree of capacities utilization of smelters and refineries depending on the price level, The model contains a statistic part corresponding to the capacities distribution by the production cost, and a dynamic part determining the deviation from the static depending on the price variation dynamics, The developed complex system has been identified by the actual data of the world prices of smelter grade alumina and primary aluminium, conservation and reactivation of refineries and smelters in the Western countries within the period from 1992 to 2003. The system was used for primary aluminium and alumina price forecasts till 2020.

Jan 1, 2004

By C. H. B. Leitch, T. N. MacAuley, R. L. Linnen, A. E. Williams-Jones

"The Trout Lake stockwork molybdenum deposit is temporally and spatially related to the emplacement of a late Cretaceous granodiorite-tonalite stock in southeastern British Columbia and contains an estimated 49 million tonnes grading O.I9% MoS2- No metal zonation patterns are apparent, with the exception of peripheral tungsten skarn, and exploration was guided largely by geological interpretation. It is typical of the granodiorite, or fluorine-poor type of molybdenum deposit. Molybdenite is contained within a quartz-feldspar vein stockwork and coeval dissemination in igneous (and less commonly metasedimentary) hosts. In general, molybdenite is strongly associated with alkali feldspars, but in detail it is intimately associated with incipient muscovite replacement of albite and K-feldspar; veins that lack feldspars are also typically barren of molybdenite. These textures suggest that fe/dspathic alteration (and precipitation in veins) was an important precursor to mineralization, and the occurrence of similar textures elsewhere (e.g. Henderson) suggest that early feldspathic alteration is important to the genesis of molybdenum deposits in general. Molybdenite deposition at Trout Lake was preceded by contact metamorphism, skarn and potassic alteration, and was overprinted by muscovite-ankerite (phyllic) alteration. Only moderate temperature changes are recorded by the metamorphic and alteration mineral assemblages (350°C to 450°C}; however, with time, fluids became increasingly more acidic and enriched in C02- In light of the intimate molybdenitemuscovite intergrowths, the decrease of pH probably exerted a major control on mineralization.IntroductionGranite-hosted molybdenum deposits can be classified in terms of the composition of the related intrusion, e.g., the granodiorite and granite types of Mutschler et a!. (1981), or the calc-alkaline, alkali-calcic, and alkalic types of Westra and Keith (1981). They have also been classified on the basis of their fluorine contents (Theodore and Menzie, 1984) with the fluorine-rich and -poor varieties roughly corresponding to granite- and granodiorite-type deposits, respectively. For economic reasons, most exploration and research has concentrated on the high-grade/large tonnage granite-type of deposit, exemplified by Climax. F1uorine-poor, granodiorite-type deposits are, however, the most common type in Canada and have been mined in the past (e.g., Endako). In this paper, the authors summarize the research that has been carried out on the fluorinepoor Trout Lake deposit (Boyle and Leitch, 1983; Linnen, 1985; Linnen and Williams-Jones, 1987; 1990) and use what has been learned to develop guidelines for the future exploration of fluorinepoor, granodiorite-type molybdenum deposits."

Jan 1, 1995

By C. P. Moore, G. W. Taylor

Vertically dipping lenses of nickel-copper ore at Dumbarton Mines Limited are being mined by a modified blasthole stoping method. The principal access to the mine is provided by a 15-degree decline, which, in conjunction with the use of ramps and declines for secondary access, maximizes the accessibility and mobility of trackless mining equipment. Sublevels are driven in ore on 80-foot vertical intervals and subsequently the ore, ranging in thickness from 15 to 30 feet, is slashed to its limits by a procedure of face sampling and test holing. Two longhole drill jumbos are used to drill off 40-foot vertical slices above and below these levels. Following blasting, the ore falls by gravity to the 500-foot horizon, where it is removed from drawpoints by load-haul-dump units and transported by truck to the main orepass. The rock is crushed to minus 3-4 inches and conveyed to surface by a 30-inch-wide wire rope suspended conveyor. This is achieved in two flights, a lower one of 290 feet and a main flight of 2260 feet. All aspects of the mining operation are discussed in the paper, including ventilation, services and safety.

Jan 1, 1973

By M. A. F. Fedikow, D. A. Baldwin, C. Taylor

The Agassiz Metallotect and the Johnson Shear Zone represent two metallogenetic fea tures located within the northern and outhern belts, respectively. of the Aphebian-aged Lynn Lake greenstone belt in northern Manitoba . Numerous gold occu rrences are associated with these two regional features . The tratabound Agas iz Au-Ag deposit with 2.9 million tonnes of 5.2 g/tonne Au and 11.8 g/tonne Ag. occurs within the Agassiz Metallotect. The stratigraphic sequence characterizing the Agassiz Metallotect comprises interlayered ox ide. silicate and sulphide facies iron formations, biotite-rich and siliceous siltstones. and a high Mg- i-Cr basaltic rock that ha previou ly been identified as tholei itic picrite. These rocks can be traced in outcrop and by their INPUT and gradiometric signature for 65 km. The Johnson Shear Zone is an ill-defined 35 km long zone of strucwral disruption that crosscuts volcanic. sedimentary and intrusive rocks and contains numerous vein-type gold occurrences. Both of these metallotects are characterized by their low level of exploration activity and as a result offer excellent residual exploration potential. Rock, basal till and vegetation geochemical techniques applied in the vicinity of the Agassiz deposit indicate the presence of trace element dispersion halos associated with the mineralization. The halos define an exploration target larger than the mineralized zone. Gold occurrences within the two metallotects are described with emphasis on the Agassiz Au-Ag deposit . A wide range of gold occurrence-types is documented including syngencticstratabound , epigenetic-replacement and epigenetic-quartz vein .

Jan 1, 1986

By A. Allaire, J. Torrealba-Vargas, R. Welyhorsky

Early testwork was carried out to select the plant process design criteria and flowsheet selection. Additional testwork was carried out during the feasibility study to support the optimization of the plant design criteria. The test results showed that the recovery of gold was not very sensitive to grind size in the range of 75 to 105 microns. An additional result was that the presence of lead nitrate did not improve the kinetics of gold leaching. This conclusion was supported by the low content of sulphides in the ore. It was also found that the presence of lead nitrate increased copper dissolution, producing the potential for an increase of copper reporting to electrowinning, which is detrimental to the overall gold recovery process. The use of oxygen in leaching was investigated to increase leach kinetics. The results of leaching tests to compare using oxygen instead of air indicated that, due to the improved leach time, it was possible to reduce the number of leaching tanks from twenty four (24) to twenty (20).

Jan 1, 2011

By W. J. Pearson

"""POTASH"" is a term applied to the compounds of the element potassium (K) and when used in agriculture and industry is ex-pressed in terms of potassium oxide (K2O), regardless of the actual com-position of the compound. When a chemical analysis is made of a fertilizer, the amount of K is deter-mined and then calculated to the equivalent amount of K2O. However, the compound K2O does not exist in nature. Most of the world's potash supply is derived from mineral deposits similar to those in Saskatchewan and New Mexico. However, there is some production from concentrated surface brines such as occur in Searles Lake, California; Salduro Marsh, Utah; the Dead Sea; and from well brines in Micl1igan."

Jan 1, 1960

By A. D. Fisher

This paper describes the future position of metallurgical coal, particularly as applied to Canadian reserves. Quality coking coal is declining in availability, but preheating practices may alleviate this situation to some extent. Two new processes are discussed in the paper - formed coke and direct reduction - and their coal specifications are outlined.

Jan 1, 1972