Search Documents

By L. Don Leet

Abstract Earthborne vibrations from blasting and other sources, including rock bursts, can now be recorded effectively. The nature and magnitude of vibrations from various sources have been investigated and certain applications of the knowledge thus gained have been made. Vibrations from blasting have been measured on special equipment over a range from an electric blasting cap at a few feet, through the largest quarry shot in history to date ( 1,-362,985 lb.), to the first atomic bomb, in uew Mexico on July 16th, 1945. Laws relating amount of explosive to amount of vibration at different distances have been developed and tested. Special studies have been made of the effects of vibrations on buildings, particularly from the standpoint of possible structural damage. Recorded vibrations are used to study the effects of modern short-period delay shooting. It ?has been found that short-period delay firing is extremely effective in reducing vibrations under the right conditions, but with certain limitations. In quarry shooting, there appears to be a minimum number of holes below which vibrations are not appreciably reduced by short-period delay firing. In several instances this minimum has been near 7. Vibrations in the ground from rock bursts and the effects of mining in stresesd ground have been studied both underground and on the surface in a search for a rock burst warning system. Introduction Earthborne vibrations from blasting and other sources, including rock bursts, can now be recorded effectively. Analyses of blasting records have been yielding increasing funds of information of practical as well as theoretical interest. The nature and magnitude of the vibrations have been investigated with special reference to their effects on structures.

Jan 1, 1951

By Rodolfo Zanella

Au/TiO2 catalysts prepared by deposition-precipitation with NaOH (DPN) (~3 wt%) and urea (DPU) (~8 wt%) were tested in crotonaldehyde hydrogenation at atmospheric pressure. There is no differences in activity (mole.gAu -1 s-1) and selectivity between both DPU and DPN samples for a given activation treatment. This is due to the fact that DPU and DPN samples exhibit similar gold particle size distribution, although the gold loading in DPU is much higher that in DPN. The DPU samples were reduced under H2 at different temperatures (120-500 °C) or under air at 300 °C with various flow rates, to vary the average particle size within a large range, 1.7 to 8.7 nm. The selectivity to crotyl alcohol (selective hydrogenation of the carbonyl bond) is high, 60-70 %, and almost constant as a function of the particle size. The selectivity to crotyl alcohol is also constant for conversions between 10 and 50%. These results suggest that the adsorption mode of crotonaldehyde is of ?3 or ?4-type. In contrast, the TOF depends on the gold particle size, it drastically increases when the gold particle size is ~2 nm. Our results are in agreement with former studies that suggest that the gold atoms involved in the hydrogenation process are those of low coordination.

Oct 1, 2003

By John A. Hudson, Xia-Ting Feng, Joseph S. Y. Wang

Evolution over decades and progress over last five years have been made in many topics of interests to rock mechanics, geosciences, physics, and multi-disciplinary interactions in underground research laboratories and development facilities, as well as in underground energy recoveries and environmental assessments. Rock mechanics and geotechnical engineering advances are associated with quantifications of disturbed/damaged zones and rock alternation and bursting processes and creation of underground spaces and accesses associated with deepening of shafts and lengthening of tunnels. Geophysics and earth sciences advances are associated with continuing collections of seismic, electromagnetic, and gravitational data and conducting various thermal, hydrological, mechanical, chemical, and biological investigations, both separately, simultaneously, and in different coupled ways. Astroparticle and underground physics advances are associated with many long term experiments to detect rare events and needs for increasing larger and deeper halls to accommodate next generation detectors, shielings, and isolations. There are also increasing interesting in underground settings to explore multidisciplinary and inter-disciplinary sciences and technologies. Energy and environmental sciences and assessments have evolved from traditional oil and gas focuses to recent activities associated with green resources and alternative recovery/disposal strategies. The evolution and progress of these interdependent and related fields are discussed in this quadrennial Congress.

Jan 1, 2015

By K. Sun

The exothermic behavior of the intermetallic reactions inside an Al-Mn metallic powder compact and its assimilation fundamentals in molten aluminum were examined. In this study cylindrical compacts were manufactured and tested. The experimental work involved simultaneous temperature measurements of three thermocouples as well as detection of the apparent weight of the cylindrical specimen during its assimilation in liquid aluminum. The details of the intermetallic reactions prior to the compact complete disintegration were investigated by microscopically studying the morphology and local composition in a partially reacted compact. The variation of manganese concentration in the melt was determined by chemically analyzing the samples taken from the molten aluminum at specific time intervals. The exothermic reaction increases the compact's temperature above that of the liquid aluminum. In tandem with this exothermic reaction, the compact is suffering a swelling action. This swelling action disintegrates the cylindrical specimen, which is assimilated into the liquid aluminum. The intermetallic reactions proceed in a stepwise manner. Both the bath temperature and the compact composition impact on the exothermicity of the intermetallic reactions. However, when the amount of Mn in the compact is greater than 75-wt%, the maximum centerline temperature rise is slightly reduced as Mn amount increases.

Jan 1, 2004

By D. Farrish, W. A. Grell

"IntroductionMost base metal mines sell their concentrate to a custom smelter. The two parties concerned therefore draw up a contract which would detail the conditions under which concentrate sales will take place. The contract will identify treatment and marketing charges (including escalations), deductions for metal losses in the smelter, pricing formula, timing of payments, penalties for deleterious elements, etc.An understanding of the smelter contract is important to the mineral processor, for it will determine how he operates the plant to maximize economic return.Description of Contract ClausesUsing copper concentrate as an example, the smelter contract generally contains the following three basic charges:I. Metal Deductions- as the smelting process does not recover all the metal contained;2. A Smelting Charge- expressed per ton of material to cover costs on the bulk material such as receiving, unloading, thawing in winter, sampling, roasting to drive off sulphur, smelting through the matte and blister stages to recover mostof the copper and precious metals;3. A Refining Charge- expressed per pound of copper.The following is a review in some detail of a number of clauses which could be considered typical of a treatment and marketing type of copper concentrate sales contract. Most normal considerations in an agreement could be covered by the following types of clauses.Terminology- covers definitions, units of measurement to be used (e.g. short tons, troy ounces, etc.), currency (Canadian dollars). The term ""unit"" may be defined - l OJo of a ton of concentrate, e.g. one unit of copper means 20 pounds of copper per short ton of concentrate."

Jan 1, 1989

By L. K. Smith, C. R. May, K. R. Schrag, H. Buchwald

"New contracts for 65 million long tons of coking coal valued at over $900 million, over the next 15 years, herald the rebirth of Alberta's coal industry. The industry is optimistic that export orders may reach 20 million tons per annum by the mid-1970's. Coal will be extracted from underground and surface mines and it is expected that the total labour force will double from the present 1,200 men within the next two years. Ali the health hazards associated with coal mining are likely to be encountered and it will be incombent on the Provincial Department of Health to specify the standards which relate to health and environment where no such standards have previously existed. This paper examines some of the problems which are being encountered in setting up an environmental health program and reviews the practicability of environmental monitoring methods, with special reference to respirable dust."

Jan 1, 1969

"The Cordillera contains numerous porphyry deposits and prospects, many containing economic quantities of copper, molybdenum, gold and tungsten. Over the lost twenty years, different phases of exploration have been driven by individual commodity prices and new discoveries. Exploration methods have remained largely unchanged since the 1960s and 1970s with the range of techniques chosen for each situation depending on the stage of the program, the type of porphyry target and the local environment. Improvements or changes to techniques have resulted from awareness of specific features in new deposits or regional problems. During the last ten years much of the emphasis has been on the re-evaluation of known porphyry deposits with more exploration in areas previously recognized as prospective. Re-evaluation of known deposits has resulted in increased reserves, often with improved gold grade, and the discovery of new zones. Several new deposits have been discovered including gold-only deposits of probable porphyry affinity.Research related to porphyry deposits has followed trends in exploration and has been directed toward the type of deposits that have been of current interest. In addition to research on specific deposits and areas, general research related to porphyry deposits has addressed three broad themes. The first theme involves the role of tectonic processes and the nature of source regions. Although different in detail, recent tectonic models suggest that a tectonic change or hiatus may be important for the generation of metal-rich magmas from various source regions and subsequent fractionation that permits volatile saturation. The second theme is based on magmatic processes, particularly the generation of a volatile phase enriched in metals. This research supports the general orthomagmatic model for porphyry deposits and has helped to define the influence of specific variables in the generation of different types of porphyry deposits. Finally, research on alteration and mineralization has provided evidence for different types of fluids and fluid processes involved in the formation of porphyry deposits. These data also support the orthomagmatic model but indicate additional complexity in magmatic-hydrothermal systems including the role of external fluids. Although important advances have been made, research has had a limited impact on exploration.Exploration and research on deposits that occur in the peripheral and upper parts of porphyry systems have been important over the last ten years. Although considerable advances have been made, the relationship of different styles of peripheral mineralization to magmatic processes in the core of the system remains ambiguous. An improved understanding of the processes that generate zoning, peripheral mineralization, and the surrounding alteration envelopes would be beneficial to exploration."

Jan 1, 1995

By Jessica E. Heuchan

An industry survey has been conducted by the Queen's University Mining Engineering Department of 30 Canadian mining organizations to determine how effectively newly graduated mining engineers meet the needs of the industry. The principal objectives of the survey were to evaluate, and thus provide focus on change for, curricula being taught at Canadian mining engineering schools in service of the industry's needs; to provide feedback on current industry expectations; and to reinforce contacts with the industry as a means of providing future collaboration. A strong focus of the survey was placed upon industry's perception of the special attributes of engineering hires and applicability of student academic training to meet their industrial requirements. In providing this detailed summary of corporate responses, a clearer understanding of the mining industry's expectations of engineering training at Canadian colleges and universities has been gained.

May 1, 2003

By H. Tan

The effect of carbonaceous matter on gold extraction was investigated in cyanide systems with pure gold as well as pre-robbing sulfide gold ores. Auger studies demonstrated that the carbonaceous matter preferentially smeared on iron sulfide rather than aluminosilicate surfaces during wet or dry grinding. During mechanically mixed leaching, coating of sulfides and silicates and stripping of carbonaceous matter occurred simultaneously. TEM and XPS studies indicated preferential coating in the form of elemental (graphitic) carbon at the edges and the defect sites of particles. Interestingly, carbonaceous matter extracted from the gold ore was predominantly graphite and not preg-robbing in a solution with a high KCN concentration. However, the carbonaceous coating had a significantly detrimental effect on gold dissolution when gold was pre-ground with the gold ore. Artificial coating on gold surfaces with the natural carbonaceous matter from the ore was also found to substantially retard gold dissolution. With the addition of the natural carbonaceous matter from the gold ore, gold extraction from two non preg-robbing sulfide gold ores was inhibited owing to carbonaceous coating. The presence of carbonaceous matter significantly reduced the current density for gold oxidation and increased the current density for pyrite oxidation. This could explain the fact that carbonaceous coating hindered gold dissolution while enhanced sulfide preg-robbing.

Jan 1, 2005

By D. W. Tully

Sedimentary and volcanic rocks of the Timiskaming series trend west-ward across the property of the Upper Canada mine, forming part of the north limb of a regional syncline which is truncated on the south by the Larder Lake fault zone. A wide zone of schistosity strikes east-west through the sediments and volcanics. The central portion of this zone is occupied by a system of narrow gouge-filled fractures in highly altered rocks, mainly tuff, trachyte, trachyte porphyry and syenite porphyry. The alteration zones have developed through repeated stages of deformation and accompanying metamorphism. The initial stages were marked by carbonatization and sericitization, followed by silicification and the introduction of minor amounts of sulphide minerals. Gold was finally de-posited in relatively late fractures within silicified zones and pyrite. Repeated movements along the Up-per Canada break have offset post-ore dykes of minette and diabase, and have resulted in minor displacements within the orebodies.

Jan 1, 1963

Between 1993 and 2003, a series of AG and SAG mill pilot plant trials were conducted using Hardinge Ical pilot plant scale SAG mills on numerous ore samples and ranging across a wide variety of operating conditions. The data from these tests were used to evaluate the design of SAG and AG mill circuits for over a dozen projects, of which about half were eventually constructed and commissioned. The data were also used in the development of SAG mill modelling, scale-up and simulation procedures by several consultants who had access to part of the data set. Recently, we have had the opportunity to bring this data together and further analyse the consolidated dataset. This paper reports on the outcomes of this analysis that has identified the impacts of different AG/SAG circuit flowsheets and operating conditions on energy efficiency and operating cost.

Jan 1, 2012

By G. E. Agar

"The distribution of gold in the grinding-classification circuit of an operating gold plant was determined by assaying the size fractions of samples from each of the streams. This analysis identified the streams with the maximum potential for gravity recovery of gold and revealed that there was up 110 seventy-five times as much gold in the primary cyclone underflow as in the concentrator feed.Laboratory jigging and tabling tests were done on samples from two of the streams to determine what the recovery might be with a gravity circuit and to show that a high grade concentrate could be produced. A numerical simulation procedure was used to calculate a material balance for a circuit that included gravity separation on the primary cyclone underflow. The numerical simulation optimistically indicated that as much as 84% of the gold might be recovered in a reasonable grade of concentrate even though the recovery in batch bench scale tests was only 14%.Incorporation of a gravity separation device would reduce the inventory of gold in the grinding-classification circuit.INTRODUCTIONMany gold concentrating plants include a gravity concentration operation while others do not and the reasons that some do and some do not is not clear. Some of the advantages and disadvantages of gravity circuits are discussed by Penman (Penman 1987) without clear cut resolution. Penman's comments elicited an interesting response from Lloyd (1989) who produced a simple way to determine if the addition of a gravity concentration circuit would enhance the recovery of gold. Lloyd's method does not consider the cost of running the circuit so it only partially answers the question. There are reports in the literature (Wells and Patel 1991, Matwijenko 1988) that as much as 60% of the entire production comes from a gravity circuit when it is used, and that the grade of the concentrate produced often exceeds 65% gold, an assay that far exceeds most Merrill-Crowe precipitates that are sent to refining. In at least one instance (Hood 1984) a range of recovery from 40-50% was indicated from laboratory test work and the plant subsequently realized recoveries in the range of 26-40%. Despite these favorable numbers other plants use gravity separation when as little as 20% of the gold is recovered in the gravity concentrate (Carter 1992)."

Jan 1, 1993

By Shengwu Song, Xuemin Feng

Jinping I hydropower station is located in Sichuan Province in Southwest China. It is built on the Yalong River as a controlling cascade hydropower station in the middle and lower reaches, with power generation as its major function. Jinping I arch dam concerns many engineering issues and has attracted worldwide attentions due to its huge scale and unique settings. It is one of the most challenging projects in China with its 305 meters high arch dam and complex geological conditions for construction, including large-scale tectonic faults, intensively unloaded rock masses and geological asymmetry in its foundation. At present, the concrete arch dam construction has been completed and preliminarily impounded, most of the foundation treatments have been implemented, and four of six generator units had been put into operation in July 2014. In this paper, the analytical methods, design concepts, treatment measures and technical features of strengthening the geological defects in the dam foundation will be presented. Upon geological investigation into the dam foundation, a few large-scale weak discontinuities are observed. The rock masses in the left dam foundation are intensively unloaded, approximately to the horizontal depth of 150–300 m. These serious geological defects lead to a geological asymmetry on the left and right banks, and thus some major difficulties of dam construction are encountered. The influences of geological defects on the dam construction and safety are analyzed comprehensively, followed by the concepts and methods of treatment design. Based on this, the treatment methods of the weak rock masses and discontinuities are carefully determined by numerical analysis and scheme optimization, including the concrete cushion, concrete replacement grids, drainage system, anti-seepage curtains and consolidation grouting, which work together to enhance the strength and integrity of the dam foundation. Evaluations and calibrations through geo-mechanical model tests in combination with field monitoring results in early impoundment period show that the arch dam and its foundation are generally stable and function normally, which suggests that the research methods and treatment design schemes are reasonable and effective. The proposed treatment methods and concepts in the context are helpful for similar complex rock projects.

Jan 1, 2015

By R. Heikkilä

The utilization of Building Information Modeling (BIM) and model based 3-D control of work machines have increased a lot in new road construction in Finland as well as in other Nordic Countries. Up today, much less attention has been paid into the development of maintenance and rehabilitation processes. As a part of a large research and development program RYM PRE Infra FIN BIM in Finland, a focused research project of the BIM with experiments in total five (5) pilot projects has been performed. A main idea of the new BIM based process has been to utilize mobile laser scanning method for initial data acquirement, the use of novel 3-D analyze and modelling methods for point cloud processing, the use of new type optimization method for the planning of geometric and structural improvements needed for the existing uneven road surfaces, and further, through the creation of 3-D machine control models apply the newest 3- D machine control systems for continuous 3-D control of practical construction work using milling machine and asphalt paver. Finally, an evaluation is made between the new process model and the traditional way of working.

Aug 1, 2013

By David S. Wong

With air emission limits for total particulates continually tightening, management of `potroom dust' or airborne particulates from aluminium smelting potrooms is of increasing importance. To better understand how settled and airborne particulates are generated within a potroom, methodologies have been developed to sample and analyse the compositional signature of dust, in relation to its sources. During a smelter case study, these methods allowed tracking of mineralogical phases in dust across a range of potroom locations, showing that the mechanisms of dust generation do vary spatially and vertically in a potroom. Such methodologies may also be applicable to other metallurgical industries.

Jan 1, 2011

By G. Bourque

One of the design criteria for the Mount Wright facilities was to incorporate the latest proven automation techniques and devices for the new crushing, grinding and concentrating plant. The heart of the centralized control system is a Fox 1 process computer, located in the central control room in the administration building. The entire operation, i.e. crushing, conveying, storing, grinding and concentrating, is monitored and controlled, through the process computer , by one operator via a CRT console. In case of computer failure, the control is automatically, and without process interruption, transferred to manual back-up panels. One of the newest management tools, the process computer is programmed to collect and automatically print out shift. daily and monthly reports on tonnage, metallurgy and equipment operating time, for better planning of operations and preventative maintenance.

Jan 1, 1977

By F. Dubuc

"The Adams Mine of Jones & Laughlin Steel Corporation is situated on the Boston Township iron range near Kirkland Lake, Ontario. Eight different orebodies have been outlined, with a total open-pit crude tonnage of. about 100,000,000 tons or the equivalent of 30,000,000 tons of concentrate. The ore consists of fine-grained, well-bedded Early Precambrian iron-formation composed essentially of alternating layers of chert and magnetite. Grade averages about 22 per cent magnetic Fe.The iron range varies in width from 3,000 to 4,000 feet and is made up of several horizons of iron-formation, cherty ""quartzite"" and volcanic rocks. The latter consist mostly of basic lava flows and minor amounts of tuff. Dips are rarely Jess than 50 degrees, and the range is believed to represent an overturned limb of a major synclinal structure. Dykes of syenite and lam prophyre, along with local younger diabase, intrude the rocks of the iron range."

Jan 1, 1966

By John Shirokoff, Ladan Khaksar

"Cyclic polarization technique and also potentiodynamic measurements were applied to study corrosion behavior of 13% chromium steels in chloride containing environment. Potentiodynamic measurements were performed at 25 and 75 °C with 0, 10 and 20 g/l NaCl in 0.01 M hydrochloric acid solution. At the same time, the significant pitting parameters such as corrosion potential (Ecorr), pitting potential (Epit), protection potential (Epro) and passive current (Ipass) of cyclic polarization curves with various NaCl concentration were analyzed and compared to describe the corrosion behavior of 13% chromium stainless steel. Surface measurement techniques such as SEM and EDS were used for morphology and analysis of corrosion products. The results showed that both temperature and Cl- concentration had significant effects on corrosion behavior of 13% chromium stainless steel in acidic solution.INTRODUCTION Of all the corrosion resistant alloys (CRA) used in oil and gas developments, martensitic stainless steels (MSS) are some of the most common ones these days. These steels not only have the advantages of normal steels: high strength, cost-effective, easy to manufacture, available in a wide variety of product forms, but they also have good CO2 corrosion resistance at higher temperatures as a result of their 11% minimum chromium content. One of the most common types of MSS used in the oil and gas industry is 13% chromium steel. NACE and API standards both reference several different varieties of 13% chromium steels for use in oil and gas projects(“Corrosion Resistant High Cr Steel for Oil and Gas Wells,” 2013). All types of 13% chromium steels have about 12 to 14% chromium and other minor alloying additions, and can be placed into two general groups: conventional and modified. Conventional 13% Cr steels (13Cr) are those most common in oil and gas, some of which are CA6NM (UNS J91150), AISI 410(UNS S41000), and AISI 420 (UNS S42000). These alloys have excellent corrosion resistance when compared to carbon steels up to about 300°F (150°C) and are used for a variety of wellhead, tubular, and downhole components however they have very limited resistance to cracking in H2S (Vallourec Group, 2015). Modified 13% Cr (M13Cr) steels came from the need for increased corrosion resistance at higher temperatures, increased H2S cracking resistance, and increased yield strength above 85 ksi (586 Mpa) primarily for tubular goods and other downhole equipment. These features were developed by taking a conventional 13Cr steel and adding nickel (Ni), molybdenum (Mo), copper (Cu), and other alloying elements. M13Cr provides better corrosion resistance than 13Cr up to about 350°F (177°C), yield strengths up to 110 ksi (758 Mpa), and also improved H2S cracking resistance(“Corrosion Resistant High Cr Steel for Oil and Gas Wells,” 2013)."

Jan 1, 2017

By H. F. Naldrett

"AbstractAt the end of May, 1950, Imperial Oil, Limited, had completed a total of 192 D-3 wells in the Leduc-Woodbend field, 62 of which lost circulation in the D-3 zone for periods ranging from two hours to fifty days. The majority of the remaining wells •lost some mud without actual loss of returns. In addition, independent operators completed 69 D-3 wells, of which 9 lost circulation. Included among the latter is the now well known Atlantic No. 3 well, which blew wild out of control for seven months. The well was finally brought under control through two directionally drilled wells, but not before the derrick fell and the well caught fire. Practically all known filler materials have been used in attempt3 to prevent or regain loss of circulation, but none has been successful, except in minor cases. Ordinary sawdust has come to be the most commonly used filler material and is added to the mud before the D-3 zone is contacted. In cases of serious loss of circulation, the on1y successful method of getting returns has been the use of a series of small cement plugs.IntroductionThe Leduc field is twenty miles southwest of Edmonton, Alberta. Geologically, it is on the east limb of the Alberta syncline, in the homoclinal belt. The main productive zones are in the Upper Devonian formation and are known locally as the D-2 zone and D-3 zone, respectively (see Figure 1).The D-3 zone is a dolomitized reef with fair average porosity and permeability, and shows considerable evidence of vertical fracturing. Porosity is mainly due to moderately uniform development of vugs which are interconnected by small crevices. However, the formation is known to be, locally, extremely vuggy and in places cavernous. These latter conditions create very serious drilling problems due to the hazard of loss of circulation, particularly in the gas cap, which has a maximum thickness of 200 feet. The D-3 zone is contacted at an average depth of 5,300 feet."

Jan 1, 1950

By Minerals Refining Company, Gerald Luttrell, Biao Li, Robert Bratton, Roe-Hoan Yoon, Stan Suboleski, Nikhil Gupta

Flotation is regarded as the best available method of upgrading coal and mineral fines in the mining industry. However, its efficiency deteriorates rapidly with decreasing particle size. Furthermore, ultrafine concentrates are difficult to be dewatered economically. Due to these technological problems, some operators are forced to discard at least part of the ultrafine materials to tailings (or refuse) ponds, causing significant losses of valuable resources and creating environmental concerns. To address these technological issues, a new separation process named hydrophobic-hydrophilic separation has been developed on the basis of the recent advances in the science of hydrophobic interactions. The results obtained to date show that the process can recover and dewater ultrafine particles simultaneously with high separation efficiencies. Following a series of extensive laboratory tests, the process has been scaled up to proof-of-concept and pilot-scale continuous tests. The results obtained with desliming cyclone overflows, screenbowl effluents, and by-zero coal flotation feeds can be cleaned to less than 4% ash and moisture with over 97% organic matter (or coal) recoveries. The results obtained with mineral fines also showed encouraging results.

Jan 1, 2016