Search Documents

By I. E. Puddington, F. W. Meadus

The beneficiation of barite in mill tailings using an agglomeration technique has been demonstrated. Barite was selectively absorbed from a conditioned aqueous slurry into a collector oil by mechanically mixing slurry and oil. The resulting oil-bonded barite-containing agglomerate was washed, to remove gangue material, and further mechanically contacted with dilute H2SO4 This treatment resulted in the transfer of barite into the aqueous phase. Grades as high as '97% BaSO4, with recoveries of 80%, have been obtained using this technique.

Jan 1, 1973

By H. J. McQueen

Aluminum was hot worked at 400 - 500°C and strain rates (e ) of 0.004 -0.1s-1, under reversing strains (c) of 0.5 to 0.2 or 0.5 to 0 and also advancing from 0.5 to 1 or 0.5 to 5. Under similar test conditions for different parts of the strain paths, the average measured flow stresses are found to agree with each other. In the forward and backward strain path tests, the almost identical steady state plateaus affirm the occurrence of dynamic recovery (DRV). On reversal of strain direction at constant e , there was generally negligible Bauschinger effect. In specimens annealed at 400°C, static recrystallisation (SRX) was followed microstructurally. mainly by disappearance of elongated grains with serrated boundaries because the new grains were only little a finer than the old due to low strain energy. The only influence of reversing strain path observed was the effect of change of grain boundary area as grains elongated or returned towards equiaxed. In optical microscopy, elongated grains with serrations and deformation bands confirmed DRV in forward path specimens. In reverse path specimens, equiaxed grains were gradually restored with retention of serrations and bands. In low magnification polarized optical microscopy, grain alignment increased with strain for forward path specimens; whereas it decreased in reverse path ones, supporting DRV. Orientation imaging microscopy (OIM/SEM) revealed that elongated grains are broken up as deformation bands rotate during the forward path and that grains return to equiaxed appearance on backward straining. Comparative studies using optical microscopy in polarized light (POM), OIM/SEM and transmission electron microscopy (TEM) revealed that while subgrains remain equiaxed and constant in size and character during the forward and backward paths, the fraction of low angle facets decreased while that of high angle grain facets increased with increasing strain; these are coupled with a fairly low fraction of medium angle boundaries. The results contribute to the understanding that dynamic recovery in aluminum maintains sub-boundaries with low misorientation but as grains elongate and more subgrain become adjacent to grain boundaries the fraction of high angle boundaries rises (with backward straining it was vice versa).

Jan 1, 2007

By L. K. Daneshmend

Key issues in managing information systems in the minerals industry will likely continue to be those relating to the integration and interoperability of disparate systems. This paper argues that, in order to harness the promised benefits of information technologies, the mining industry should adopt a set of open systems standards to define data formats and protocols for seamless data exchange. This is in direct contrast to the present situation where mining equipment, software and instrument suppliers rigidly adhere to proprietary standards for fear of losing competitive advantage. Benefits to the mining sector resulting from the adoption of such standards would be: the provision of near-time data for executive decision support, and the freedom to choose best technologies. The principal benefits to the leading mining software suppliers will be increased market share as a result of “captive sites” converting to open systems standards. Examples are given of open systems standards developed for related industries such as the Petroleum Open Systems Corporation (POSC) and the Machinery Information Management Open Systems Alliance (MIMOSA).

Jan 1, 2000

By Hajime Miki, Gde Pandhe Wisnu Suyantara, Tsuyoshi Hirajima, A. M. Elmahdy, Keiko Sasaki

"Seawater has been reported to depress molybdenite in a copper-molybdenum (Cu-Mo) flotation process at high pH due to the precipitation of Mg(OH)2. Meanwhile, to improve mineral recoveries, collectors are usually added into the flotation cells, thus adding the complexity to the mechanism of bubble-particle interactions involved in Cu-Mo flotation. Therefore, understanding the interaction mechanism in seawater flotation and in the presence of collectors is important to explain the minerals depression. The present work investigated the effect of kerosene on the bubble collision and attachment to pure chalcopyrite and molybdenite surfaces in MgCl2 solution as one of the seawater major components at pH 6 and 11. Mineral surfaces were characterized using atomic force microscopy (AFM). In addition, minerals floatability in the same system were tested in a column flotation. The study of bubble-particle interactions shows that following several collisions, bubble could displace the intervening liquid layer on the mineral surfaces, forming a three-phase contact (TPC). A TPC formed more rapidly in the presence of emulsified kerosene in a 0.01 M MgCl2 solution at pH 6 for both minerals. The reason is kerosene increased the surfaces hydrophobicity and destabilized the intervening liquid layer on the surfaces. Moreover, the average time required to form a TPC was shorter on molybdenite surface. This can be attributed to the effect of adsorbed kerosene on molybdenite surface and molybdenite surface roughness.INTRODUCTIONIn froth flotation, bubbles are used to separate hydrophobic mineral particles from hydrophilic particles. In this process, bubble-particle interactions (i.e., collisions, attachment, and detachment) are crucial with regard to mineral recoveries. The effectiveness of froth flotation depends on the formation of stable aggregates between the hydrophobic particles and the bubbles, allowing the bubble to carry the particles to the froth layer. To form such aggregates, the bubbles and particles must collide, and the intervening liquid layer must be drained below the liquid layer critical thickness, forming a stable threephase contact (TPC) (Ralston & Dukhin, 1999). Particles detachment may take place if the particles still have sufficient kinetic energy and the TPC is not formed. Previous studies of bubble-particle interaction in electrolyte solutions have been conducted using atomic force microscopy (AFM) (Assemi, Nguyen, & Miller, 2008), and by approaching the bubble using mica plate (Pushkarova & Horn, 2008), however, these studies did not focus on the bubble-particle collisions. Bubble collisions and attachment to hydrophobic (Teflon) and hydrophilic (glass) surfaces in a a-terpineol solution have been investigated by Krasowka et al. (2003)."

Jan 1, 2016

By Grant J. Goddard

"The Iron Ore Company of Canada (IOC) has been in operation for over 30 years. Today, and in the future, technology and its application will play an ever more critical role in the company’s business success.The Carol Mining and Concentrating (CMC) division of IOC is energetically applying technology today to enhance performance and results, and is aggressively exploring opportunities to apply technology to support improved business results in the future.A critical area of focus is the application of technology to maintenance management performance. CMC has taken a “back to basics” approach to the fundamentals of maintenance management in 1995 and 1996. In parallel, the mine is aggressively implementing its Vision 2000 maintenance integration plan. This plan is targeted at levering the energies applied to sound maintenance management fundamentals as the company moves to a fully condition based maintenance approach.This paper discusses some of the strategies, key technologies and objectives of theVision 2000 maintenance integration plan at the mining operations of IOC."

Jan 1, 1996

By K. Forsberg, A. Rasmuson, R. Rodriguez Varela, J. Martinez De La Cruz

"This study analyzes the separation of rare earth elements by means of a supported liquid membrane (SLM) with the final objective of recovering REE from an apatite concentrate (Alemrajabi, Forsberg, & Rasmuson, 2015; Mohammadi, Forsberg, Martinez de la Cruz, & Rasmuson, 2015). In this study, the feed phase consists of an aqueous phase containing REE, the membrane phase contains the organic solvent and carrier (D2EHPA and EHEHPA), and the stripping phase is a hydrochloric acid solution. An evaluation of mass fluxes, separation efficiency, and membrane performance is conducted. In order to analyze the suitability of liquid membranes in the extraction of REE, a deeper insight into the mechanisms causing instability is needed. In this study, surface tension is considered as the key factor of Marangoni instabilities and spontaneous emulsification.INTRODUCTIONThe demand of REE and their compounds has increased considerably due to their special physicochemical features that make them crucial elements for numerous high-tech applications, including wind turbines, hybrid cars, mobile phones, and defense technologies. They are also extensively utilized in traditional industries such as nuclear energy, petroleum, metallurgy, agriculture, and textiles (Xie, Zhang, Dreisinger, & Dyole, 2014; Zhang, Wu, Bian, & Zeng, 2014).Solvent extraction is widely used for the separation of REE (Xie et al., 2014; Zhao, Huo, Pan, Li, & Liu, 2014). Di-(2-ethylhexyl)-phosphoric acid (D2EHPA) and 2-ethylhexylphosphonic acid mono-2-ethylhexyl ester (EHEHPA) are two of the most effective extractants for the separation of rare earth elements among organophosphorus extractants (Gupta & Krishnamurthy, 2005). However, the difficulty in stripping loaded D2EHPA extractant, especially for heavy REE, has limited its utilization. Yttrium can be stripped at lower acidities in EHEHPA systems compared to D2EHPA systems (Gupta et al., 2005), but the extraction efficiency is lower. Conventional solvent extraction by mixer-settlers is restricted by its large solvent inventory and loading limits, and suffers from phase disengagement, emulsification, loss of solvent, and flooding problems (Swain, Jeong, Lee, & Lee, 2007). In this context, supported liquid membranes (SLMs) present a potential alternative due to their advantages, being low solvent inventory, process simplicity, low energy and operational costs, great enrichment ratio, and combination of extraction and stripping into one single step. A SLM is a system in which two aqueous phases are separated by an organic liquid membrane suspended in the pores of a porous support by capillary forces. One of the aqueous phases is the feed solution with the solute and the other is the stripping or receiving solution. The solute diffuses through the liquid membrane and then is extracted into the stripping solution (Kislik, 2010)."

Jan 1, 2016

By M. Jackson, R. McDonald, T. Osken, D. Robinson

"The addition of sulphidic materials in the leaching of nickel laterites has several potential benefits that include improvements in the rheological behaviour of the blends, reductions in the sulphuric acid and steam requirements, sweetening of the nickel grade of the combined feed material, and the option of using a range of sulphidic materials. The current study examines the oxidative processing of 30% w/w blends of nickel concentrate and nickel laterite ore at 250oC. In particular, the viability of using low oxygen overpressures was examined for significant amounts of nickel flotation concentrate, up to 12% w/w. Further to this the impact of process water quality, in particular the presence of chloride, upon the kinetics of extraction and the mineralogy of the residue were also investigated. This paper will present the results of preliminary work in this area.INTRODUCTIONThe use of sulphidic ore as a source of sulphuric acid during oxidative hydrometallurgical processing is not a novel idea and can be traced back over forty years (Seidel & Fitzhugh, 1968). A series of patents pertaining to application of this approach for laterite ores can be subsequently found (O’Neill, 1973; Opratko et al., 1974; Rodriguez, 2008a, 2008b; O’Callaghan, 2010; Liu et al., 2011) and a few of articles containing published data (Ferron & Fleming, 2004; Quinn et al., 2009). The use of pyrrhotite tailings as a source of sulphuric acid has also been employed for the leaching of converter slags (Perederiy et al., 2011).It is known that hydrometallurgical operations such as the HPAL plant at Murrin Murrin have added small amounts of sulphides as either transitional (mixed sulphide/oxide) ore or non-smeltable concentrate. This can improve the rheology (Rodriguez, 2009) and provide heat credits. However these plants are generally limited in their ability to add such materials due to their reducing nature and given under highly acidic conditions that the breakdown potential of the titanium used for the autoclave lining is significantly reduced. A suitable oxidant must therefore be present to ensure the potential remains sufficiently high."

Jan 1, 2012

By J. Jung, W. Keller, A. Zucht

"The agitator design for nickel high pressure acid leach autoclaves (HPAL) is critical with regard to the process result, i.e., the recovery rate. Further considerations during the design phase are the avoidance of acid hot spots which reduce the lifetime, due to corrosion of the wetted parts, including components manufactured from titanium. Besides the process knowledge to design HPAL autoclaves, tools such as, Computational Fluid Dynamics (CFD) supplemented by lab testing allow the design of optimized agitation systems. This paper describes the effect that different feed point locations have on instantaneous blending of the reactants. Furthermore, experiments and CFD show where abrasion issues might occur and how to obtain information about the static and dynamic forces acting on internals. We show how simulations can be validated by lab testing to ensure that the CFD models are applied in an appropriate way.INTRODUCTIONAgitated systems in hydrometallurgical processes have to comply with multiple process tasks and in many cases have to withstand extreme operation conditions such as pressure up to 50 bar, elevated temperatures of up to 250°C and exposure to very acidic or alkaline environments and abrasive ores. The process tasks range from instantaneous mixing of reactants, homogeneous suspensions of up to 65% wt. solids with coarse and heavy particles, enhancing the solid-liquid mass transfer for leaching, dispersing large volumes of reactants (gas-liquid, liquid-liquid mass transfer) and moreover to transport generated heat e.g., from exothermic reactions through the vessel walls or internal heat exchangers if required. For economies of scale, agitator systems have reached sizes of 5000 m³ for large open leach tanks with impeller diameters of approx. 6 m, while autoclaves nowadays have exceeded 5.5 meters in diameter with a power demand for a single compartment drive between 300 - 400 kW. In parallel all process industries require a more efficient use of resources, to generate less by-products and higher yields, while ore-bodies tend to be less qualitative and new process routes (e.g. direct leach) are developed. Besides all these facts the mixing solution must be robust and economic. In this paper we want to address our approach in the development and designing of HPAL agitation equipment."

Jan 1, 2012

By C. A. Y. Shephard, H. L. Brusset

Pressure maintenance by water flooding in the Pembina Field made consideration of wet crude dehydration and disposal of the produced water mandatory. Crude dehydration, the treatment and disposal of produced water, as well as the sale of gas and crude oil were expected to be handled more efficiently at one central point than at several conventional batteries. This plan was effected by routing the produced fluids to the central station by way of several well testing batteries referred to as satellites. To realize the full efficiency inherent in such consolidation the entire system was made self-regulating. Programming ensures the testing and proper routing of all products to their destination. Forty producing wells have been self-operated during the winter 1959 -1960 with gratifying results.

Jan 1, 1960

By V. Aitken

Line-of-sight radio control has received widespread acceptance for use in many mining methods because today’s technology offers improved economics and personnel safety. Significant advances in higher autonomy for mining machines are not currently seeing widespread use even though they offer great future potential. With autonomous capabilities being a longer-term goal, a logical sequence of advances based on TeleRemote control is proposed. Under Tele - Remote control, the operator is in direct control of the machine at all times. Three levels of Tele - Remote control systems are presented including line-of-sight, extended line-of-sight, and full load-haul-dump applications. Distributed control and sensing subsystems arranged in a vehicle control area network support incremental system expansion through the three levels of TeleRemote control and prepare the machine for integration of higher levels of automation as mature technology becomes available. This approach allows full exploitation of today’s mining automation technology with a flexible future growth path.

Jan 1, 1998

By W. J. Weymark

"The Gregg River project is located 40 kilometres southwest of Hinton, Alberta, adjacent to and east of Jasper National Park. This metallurgical coal mine has been developed as a joint venture between Gregg River Coal Ltd. (a subsidiary company of Mana/ta Coal Ltd.) and seven Japanese companies. This 200-million dollar project consists of a conventional truckshovel open-pit operation and a coal preparation plant rated at 2.14 million tonnes of clean coal per year. Mining operations started in October 1982 with plant start-up following in April 1983. Introduction This paper is an overview and update of the Gregg River project, a metallurgical coal mine being developed as a joint venture between Gregg River Coal Ltd. (a subsidiary of Manalta Coal Ltd.) and seven Japanese companies. The Gregg River Coal leases cover 3440 hectares and are located 40 kilometres south of Hinton, Alberta, adjacent to and north of Cardinal River Coal Mine (Fig. 1). This 200-million dollar project consists of a conventional truck-shovel operation and a coal preparation plant rated at 2.14 million tonnes of clean coal per year. A total of 31.5 million tonnes of clean metallurgical coal will be sold to the Japanese over a fifteen-year term. At present, mining operations are ahead of schedule and the plant started up on schedule in April 1983. Access and Climate An all-weather road, Highway 40, connects the minesite with Hinton (the nearest commercial centre) and a Canadian National Railway (C.N.R.) spur line connects the minesite with the C.N.R. main line in Edson. Hinton is accessible by road chartered airline and rail. ' ~h~ rug~ed and varied topography in the area creates large vanations m temperature and precipitation over short distances. The region is characterized by precipitation throughout the year long cold winters and short cool summers. The mean temperatur~ of the area range from a low of -14°C in January, the coldest month, to a high of 12°C in July, the warmest month. Long-term precipitation data indicates a mean yearly precipitation of 870 mm of which 620Jo occurs during the summer months."

Jan 1, 1985

By Xiaoqiong Wang, Daobing Wang, Fanbao Meng, Jianbo Wang, Hongkui Ge

"Shale gas has become an important unconventional oil and gas resources. Its effective development relies on comprehensive and accurate understanding of shale gas reservoirs. Rock mechanical properties is one of the important components of reservoir evaluation. Two adjacent black shale samples, which are cored from the depth of 1145 meters in Chongqing, southwest China, are subjected to acoustic emission(AE) test under uniaxial stress and compared with coarse grained granite. The results of synchronous AE, stress-strain and ultrasonic velocity experiments show that shale has weak anisotropy. Compared with granite sample, two shale samples are similar, but their strength, velocity and brittleness are quite different, indicating that shale has strong microscopic heterogeneity. TOC, XRD, SEM microstructure analysis show that total organic content, mineral composition and natural fractures are the main impacting factors for mechanical heterogeneity. INTRODUCTIONShale gas is a typical low-grade marginal resource, which is characterized by ultra-low matrix permeability and small single well control volume. In order to enable commerical development, complex hydraulic-fracture networks must be created in the shale to allow gas to escape from the micro/nano-pores and natural fractures where it is trapped in the rock (C. Clark et al.,2013; Ge et al., 2013). The development of shale gas requires accurate evaluation methodologies to evaluate shale reservoir properties and predict production. (Jarvie et al., 2007). Rock mechanical properties are an important part of the reservoir evaluation. It is significant for efficient drilling, completion and hydraulic fracturing to understand mechanical behavior of shale gas play (John, 2011; Wei, 2013).Rock mechanical properties mainly include heterogeneity, anisotropy, brittleness and acoustic emission activity (Lockner et al., 1992; Jerome et al., 2009; He et al., 2010; Liang et al., 2012). Shale mechanical properties are evaluated from laboratory tests following a complex workflow that covers tasks from sampling to testing (Md. Aminul Islam et al., 2013). It is common to include various experimental methods such as stress-strain curves, ultrasonic velocity and acoustic emission when evaluating the mechanical properties (Rao et al., 2006). Because of the presence of organic-rich matter, mineral composition orientation and natural fractures, shale tends to have strong anisotropy and heterogeneity (Deng et al., 2004; Wang et al., 2013; Hathon et al., 2013)."

Jan 1, 2015

By Bennett McLaughlin

AGNICO-EAGLE started sinking the Penna Shaft in 1995 with a hoisting plant capable of hoisting 1,800 tonnes per day from a 2,240 metre deep shaft. Exploration success lead to the installation of a hoisting plant capable of extracting 4,500 tonnes of ore and 1,800 tonnes of waste per day from a depth of 2,210 metres. The introduction of a new rope selection factor, permitting a safety factor of 4.0, represented the breakthrough required for a cost-effective project. This paper describes the process taken to introduce the new rope selection factor and its impact on the original plant.

May 1, 2001

By M. J. Bunyard, I. Mullany

"The pressures on mine operators are varied and constantly increasing, declining ore grades, more remote locations and increasing environmental concerns. The challenge facing the mining industry is to find new ways to process ores which are more efficient and less costly and to control them better. This requires a fundamental rethink in the way in which projects are developed, it is no longer good enough to just copy what has been done before. The process starts with the surfacing of the primary underlying constraints for the project and the establishment of new design principles to address these. The generation of new design criteria and processing options follows the well-established path of brainstorm, focus, brainstorm, refocus and economic evaluation. The aim is process intensification, doing more with less, as early as possible and better use of plant data. The methodology requires a complete geometallurgical understanding of the orebody to facilitate the evaluation of viable processing options. Examples of early stage processing considered are blast optimization and ore sorting to reject waste and reduce processing costs. Mine to mill integration, which starts with the optimization of blasting for separation, offers another way to significantly reduce operating costs and increase efficiencies.VALUE MODEL The mining industry has, over the past decade, experienced an unprecedented cycle of increased commodity prices and investments in new mining and processing capacity followed by a market collapse and fall in prices and confidence. Whilst there are now some signs of a return to investment in new capacity, the metals and mining industry is still wrestling with eroding margins and investor demand that companies achieve the full value of their assets. Metals and mining companies must work on all available levers to deflate their costs back to more manageable levels and capture the full value for their products. Levers include optimizing external spending, re-thinking make vs buy trade-offs, debottlenecking, improving availability and operating time of key equipment, more accurate and agile planning processes, value-in-use optimization, and tighter performance management. Figure 1 is a diagrammatic representation of a company’s value model. The three goals of a successful mining enterprise are social acceptance, environmental acceptance and sound financial returns to shareholders. Some of the KPI’s used to measure the success or not of achieving these goals are shown in the translation layer."

Jan 1, 2017

"Yara Siilinjärvi in Finland is the Western Europe's only apatite mine. Annually it produces one million tons of apatite concentrate, which creates 10 million tons of tailings. At the beginning of 2017, Yara replaced their conventional TSF with a new tailings treatment plant, which increased the solids content of the slurry from 45–48% to 66–68%, making it possible to deposit as a paste. This extended the life-span of the current TSF from 2020 to 2035. This paper presents the storyline of the Yara paste plant project. The project began with laboratory testing and then progressed to pilot-scale thickening and beaching trials. After successful pilot trials, the final process design was implemented. Process automation played a key role in the project. An advanced control system is needed to maintain process stability and the desired operation point in various operational circumstances. Since commissioning the paste plant has been running consistently with an underflow solids content of 66-68%, with average beach slope angles of 3.5 degrees in the tailings disposal area. Robust thickener operation also leads to the trouble-free high-density pumping and high availability of the plan. During first year of operation the plant’s availability has been very good, over 97%, and currently, the plant is operated remotely from the main concentrator plant.INTRODUCTION The Yara Siilinjärvi Plant is owned by Yara International, a Norwegian fertiliser company. Yara Siilinjärvi is Western Europe's only apatite mine, and it primarily produces apatite concentrate for its Siilinjärvi phosphoric acid plant. A portion of the concentrate is also dried and shipped to other Yara fertiliser plants. The site annually produces one million tons of apatite concentrate, which creates approximately 10 million tons of tailings. Extending the lifespan of the 1150-hectare tailings storage facility has been studied in Siilinjärvi for a long time. The aim has been to use the same tailings area footprint, without any new land purchases or major dam increases. An important part of the process has been to study the possibilities for using new technologies, especially thickened tailings technology (Ruhanen, 2014)."

Jan 1, 2019

By D. F. Zhang, X. Q. Jiang, N. Tahreen, D. L. Chen, F. S. Pan, D. Y. Li

Alloying with rare-earth elements has been proven to be an important tool for magnesium to achieve superior properties via texture randomization. The role of yttrium in texture weakening and the link between texture and formability are fairly well known. Since annealing is a vital part of metal processing which could significantly contribute to ductility, it is important to ascertain the impact of annealing in terms of texture change. Also, an understanding about texture development during pre- and post-deformation annealing is essential to improve the industrial deformation processing as texture is closely related to formability. While there is independent information in the literature regarding the effect of rare-earth addition and heat treatment on the texture formation, no systematic studies have been reported on the collective impact of yttrium addition, annealing and deformation on texture evolution. The present study was, therefore, aimed to identify the inter-relationship among texture evolution, yttrium content, heat treatment and deformation behavior in an extruded Mg-Zn-Mn-Y alloy. Annealing at 450°C for 1 hour and uniaxial compression tests at a certain amount of deformation were performed. The deformed and annealed samples were then subjected to annealing and compression test, respectively, followed by texture measurements. It was observed that yttrium addition effectively weakened the crystallographic texture in all conditions, which was evident from the changes in the microstructures and textures.

Jan 1, 2015

By John J. Laffin

"IN THE BOOK that has been rated the best seller of all time, it is predicted that man will earn his livelihood by the sweat of his brow. Apparently man has accepted the statement as a challenge and has been attempting to refute it ever since, as he continues to transfer the workload to his inanimate servants - the many types of machines and other labour-saving devices that are available to assist or perform for him in the normal tasks of the day. The history of the evolution of the use of energy takes us back to primitive man, who existed in a very low energy environment, the only energy available being his own muscle power. Although man took a great leap forward when he discovered fire, which was used for lighting, heating and cooking, he still depended upon his own muscles for power. Early man's greatest achievement was probably the invention of the wheel, which permitted him to utilize the muscle power of animals. While still in a very primitive state when viewed from the perspective of the twentieth century, man, with fire and the wheel, had achieved a standard of life far exceeding that of his predecessors. Looking beyond the very basic elements of human energy, fire and the muscle power of animals, we find the next additions of energy coming from man's mastery of other elements of nature. The Phoenicians utilized the power of the wind and the Romans adapted the energy of falling water to the water wheel."

Jan 1, 1972

By L. T. Pasiechnyk

After a brief review of the various hydrocarbon storage methods currently being utilized and statistics on underground hydrocarbon storage, this paper will briefly describe the technology involved in solution mining salt to create caverns of engineered shape and size and briefly discuss the economical and environmental advantages of hydrocarbon storage in solution-mined salt caverns. Other possible uses of salt caverns will be mentioned.

Jan 1, 1978

By G. D. Bateson

"The Low NOx/SOx (LNS) Burner is a technology which, in pilot-scale tests, significantly reduces acid rain-forming emissions from the burning of coal. The precursors of acid rain are nitrous oxides (NO) and sulphur dioxide (SO:;) . TransAlta is currently planning two demonstration projects.Esso Resources Canada and TransAlta are undertaking a project to demonstrate how coal can be burned cleanly for steam raising in heavy oil operations by using TransAlta's LNS Burner on a steam generator at Esso's Cold Lake Production Project. The $10.7 million project started up in mid-J990, with testing to be completed in mid-I99J. The province of Alberta and Western Economic Diversification Canada, along with other private industry, are contributing funding to the project.The other demonstration project that has been selected for funding under the United States Department of Energy's Innovative Clean Coal Technology Program is a retrofit of LNS Burners to a 33 MW cyclone unit at Southern Illinois Power Cooperative's Marion generating plant. The US$13.6 million project is scheduled for completion 18 months after final funding arrangements are made.TransAlta believes that these demonstrations will lead to the development of a commercial ""clean coal"" technology. Other demonstration projects being planned will further broaden the base of applications.IntroductionTransAlta has recognized an increasing concern worldwide for the environment, and in particular the acid rain problem. Increasing public concern and the need to meet either current or possibly more stringent emission regulations have prompted them to explore various emission reducing technologies - despite the low sulphur content of its coal.The flue gas desulphurization (FOD) and selective catalytic reduction (SCR) technology currently available to reduce sulphur and nitrous oxides from coal burning power plants is very costly. Having to incorporate FGD technology, or ""scrubbers"", greatly adds to the cost of producing power. Having to add such high costs to electric customers' bills is something TransAlta is striving to avoid.There are many research programs now underway which are evaluating ways to provide electricity from coal in a clean manner. TransAlta has been observing or participating in a variety of these programs. However, there is one new technology which the company has identified as having the potential to control acid rain causing emissions at a fraction of the cost of conventional systems. That technology is called Low NOx/SOx, Burner - or LNS Burner."

Jan 1, 1990

By H. E. Miard

"IntroductionIT HAS BEEN SAID, with good reason, that the future of the coal mining industry, in our mountainous regions at least, depends on ability to extend operations successfully to depths greater than those reached until now. However, at many points, Nature has given definite hints that trespassing there could be fraught with very un-pleasant possibilities, unless the intruder be governed by a series of rigidly observed principles. In the coal mines of British Columbia, so far, bumps have taken place only at the Coal Creek colliery, but there they gave ample evidence of the extent to which they can hamper underground operations. Some of these manifestations have also been experienced at the McGillivray Creek colliery, in Alberta, at Carbonado, in Washington, and at Sunnyside, in Utah.Cognate phenomena, known as 'air blasts', have been experienced also in some deep metalliferous mines in British Columbia. Such occurrences were responsible for three fatal accidents at the Le Roi and War Eagle mines, near Rossland, in 1916 and 1917.In more or less disturbed coal fields, another form of stress release, equally detrimental, has been still more generally experienced than have been the bumps. Coal outbursts have taken place at Morrissey and Coal Creek, in the Crow's Nest Pass district, and at Cassidy, South Wellington, and the Nanaimo Reserve colliery, on Vancouver island. Manifestations of this kind have been made the subject of intensive study in European countries where they occurred on a really impressive scale, which must not be construed as meaning that some of our own outbursts did not approach a comparable magnitude."

Jan 1, 1953