Search Documents

By H. H. Bleakney

The merit of reduction-in-area as a criterion of quality in metals is shown to lie in its influence on breaking stress, but the virtue of elongation is not easy to find. In order to assess the value of elongation, either as a measure of quality or as a guide to design, it will be necessary to separate the overall de-formation occurring in tension tests from the localized deformation associated with localized reduction in area. The obstacles to a successful solution of this problem have been shown to be more formidable than is generally appreciated, and a new solution to the problem has been suggested. This solution involves a de-vice by which an electric circuit is broken when the particular value of strain is reached that is to be taken as the point of separation between general and localized deformation. The report presents results from a number of tests on both low-carbon and alloy steels. These results indicate that the selected criterion of separation is accurately identified by the proposed method; that it

Jan 1, 1962

By K. Jomoto, H. Majima

"Experimental work has been attempted to find a useful criterion of comminution which can be determined simply in a laboratory. The suitability of the ratio of the square of tensile strength to Young's modulus, St2/E, previously derived from the theory of elasticity as a criterion of comminution, was examined measuring tensile strength, Young's modulus and critical height for drop-weight impact of five different rocks. However, satisfactory correlation between St2 /E and critical height has not been obtained, suggesting the necessity of further experimental verification of the representative value of Young's modulus of rocks. The plot of St2 vs. critical height, however, shows one-to-one correspondence, and this finding suggests that St• may be a useful criterion of impact crushing. Also, a close relationship was observed between st• and the energy index for tumbling mill grinding of •the sample rocks. It is confirmed from these findings that the quantity St• is a useful criterion of comminution of rocks, not only for impact crushing but also for tumbling mill grinding. As shown in the experimental part of this paper, the determination ol St with irregularly shaped specimens is simple."

Jan 1, 1972

By V. A. Preto

The Rexspar uranium deposit is located approximately 5 kilometres south of Birch Island, B.C. Three separate zones of commercial-grade uranium mineralization mineable by open pit have been outlined. Uranium and fluorite-celestite mineralization occur in a trachytic member of alkali-feldspar porphyry, lithic tuff, tuff breccias and pyritic schist conformably interlayered with a succession of strongly deformed greenschists and fragmental rocks that are, in large part at least, of volcanic origin. The age of these strata is not precisely known, but they are considered as part of the possibly Mississippian Eagle Bay Formation. Commercial-grade uranium mineralization is always associated with fluorphlogopite-pyrite replacement of the trachytic unit and is contiguous to, but separate from , a zone of ore-grade fluorite mineralization. In all zones, ore occurs in lenses of variable thickness and lateral extent, which lie parallel to the schistosity of the trachytic rocks and surrounding greenschists. The principal radioactive minerals at Rexspar have been identified by other workers as uraninite, uranothorite, bastnaesite, torbernite and metatorbernite. Considerable amounts of thorium oxide and widespread rare earths have been reported from all three radioactive zones. The geology of the deposit suggests that the trachytic rocks represent a highly differentiated intrusive-extrusive system in which fluorphlogopite, pyrite, fluorite and uranium-bearing minerals were deposited late in the evolution of the system by deuteric, volatile-rich fluids. The considerable amounts of thorium and widespread rare earths associated with the uranium tend to support the thesis that this element is of primary origin rather than secondary.

Jan 1, 1978

By R. A. McGuire

THE recorded production of the Sheep Creek camp from 1900, when the Yellowstone Mining Company first put its mill into operation, to the present day is in excess of $17,500,000. Of this total, $2,500,000 can be attributed to the early period from 1900 to 1916, at which time increased costs of labour and material due to the Great War forced abandonment of any operations on a large scale for a number of years. Since the camp was revived in 1929, at which time the Reno mine started large-scale operations, and the early 'thirties', when the increased price of gold induced the commencement of operations on other properties in the district, total gross production has been in excess of $15,000,000. In addition to the above totals, intermittent shipments were made by lessees and small operators, principally during the period of inactivity from 1916 to 1929, but no records of this production are available. The Sheep Creek camp would rank fifth in the Province-behind Rossland, Portland Canal, Bridge River, and Hedley-in gross gold production, but, because of relatively inexpensive mining and milling costs, would occupy a more prominent position in regard to total dividends paid. Operating mines at the present time include Reno Gold Mines, Gold Belt Mining Company, Kootenay Belle Gold Mines, and Sheep Creek Gold Mines. Each one of these companies, with the exception of Kootenay Belle, represents a consolidation of several smaller properties, all of which were in existence for a number of years prior to 1929. These four companies, at the present time, own, or hold options on, practically all the important claims in the district with the exception of a very few claims and fractions still held by private owners.

Jan 1, 1942

By H. G. Stephenson, C. W. Gregory

"This article describes the methods used for pillar extraction in the Wilson Seam at Canmore Mines, Alberta. The Wilson Seam is extremely gassy and varies in thickness between 7 and 30 ft, with an average of 12 ft. The gradient varies from 5 to 30 degrees, with an average of 15 degrees. The seam was developed using Lee Norse miners to form pillars which the company intended to extract using the same machines. Before pillar extraction commenced, an abandoned and inaccessible mine 160 ft above the Wilson had to be drained of 360 million gallons of water. When this was done pillar extraction commenced. Conditions in the mine slowly deteriorated and after 6 months the decision to withdraw the continuous miners was taken. Slusher hoists were installed to replace the continuous miners, with the result that roof conditions and safety steadily improved."

Jan 1, 1972

By A. W. Davis

Sapping and mining have constituted an important part of siege operations ever since powder came into general use in Europe. Before this period, famine was the main weapon in the hands of the besiegers, and the history of the middle ages is replete with accounts of sieges lasting two and three years. With the advent of explosives, a position impregnable to assault might be readily won by mining under, and blowing up, its defences. The natural offensive against this method of attack is to countermine and stop the attackers underground before their objective is reached. Thus developed the art of military mining. The French and British, in the Peninsular war, were adepts at this method of warfare, and the explosion of a mine and the formation of a breach were the usual preludes to the general assault of a position. In the Crimea, at Sebastopol, the British and Russians did a lot of underground fighting, as the old maps of their galleries, now in the museum at Chatham, will testify. In the siege of Port Arthur, in still later times, the Japanese and Russians were hard at it as well.

Jan 1, 1926

By Ken J. Brouwer

Stillwater Mining Company commenced construction and development of the East Boulder underground mine in 1998. This new PGM mine is situated adjacent to the East Boulder River approximately 35 miles south of Big Timber, Montana. Project planning and development incorporated detailed collaboration between the regulatory agencies, concerned citizens and mine personnel. A unique ?good neighbour agreement? was established with a local environmental group who have become actively involved in the review of ongoing site development and the implementation of environmental and compliance monitoring. Environmental management systems allow for integrated management of tailings, waste rock and water in order to minimize surface disturbances and to prevent adverse impacts to the East Boulder River. Long-term site development plans contemplate implementation of comingled waste rock and paste tailings. Water management capabilities allow biological treatment of all excess mine water in order to reduce nitrogen loadings prior to land application disposal by means of spray evaporation, snow making and land application. The comprehensive waste and water management plans have also been integrated with staged mine development and interim reclamation requirements.

May 1, 2002

By D. G. Sinclair

In any discussion on the subject of mine-safety, it is well to honestly face the fact at the outset that mining is a hazardous occupation and that certain inherent dangers attach to the work, which, in spite of the greatest vigilance on the part of everyone concerned, will from time to time exact their toll of in jury or death from the underground worker. Great progress has been made of late years in narrowing down the range of these necessary risks, and, illustrative of what can be done along these lines by concerted effort, it is pleasing to read from time to time of large operating mines running for weeks, months, a year or more, without a single lost-time accident. To achieve any results in the work of accident prevention it is necessary, first, to have a definite goal, such as a no-accident period, be it a week, a month, or a year, to aim at; and, second, to set up definite standards to work by. The legal code of regulations should form the basis of all standards of work at every mine and should, for this reason, cover as far as possible all conceivable phases of operation. This represents the ideal, but in practice it is unattainable, largely because of the many variables that must be considered, due to the divergence in the scale of operations and to differing geological conditions at the different mines. Hence it becomes necessary for the operator who wishes to attain the maximum in the establishment of high standards of safe operation to so amplify the code as to meet the peculiar requirements of his operation.

Jan 1, 1930

By G. Stenning

The paper outlines the need for high-volume ventilation in a uranium mining operation based on the design to meet environmental requirements for dust, radiation and diesel equipment. Mining methods in a highly mechanized operation, a key factor in design, are discussed. The construction and installation of major intake and exhaust fans are described briefly, together with the development of the mine airways and distribution system. Controls in the form of doors and bulkheads are important considerations in planning. Finally, the need to lower ventilation requirements in response to increasing power costs will result in future improvements.

Jan 1, 1979

By G. C. Mackenzie

At the last Annual Meeting of the Institute, Dr. C. V. Corless sketched the potential mineral wealth of Canada so clearly, graphically and with-all so entertainingly that one's imagination was fired with the promise held out to future generations for the tremendous expansion of the mining industry in the Dominion. Posterity will undoubtedly witness the fruit of much of the geographical search and survey that is now carried on by our government mining departments. Year after year the work advances, slowly but surely, new areas are . explored, older areas are surveyed in detail, the information being compiled in maps and reports of incalculable value to the prospector, the engineer and the general public. The immensity of the task of exploring, geologically, the outlying portions of the country, with the ultimate view of making valuable mineral discoveries, may be visualized from a study of Dr. Corless' paper and the subsequent discussion which took place and one becomes impressed with the fact that three-quarters or more of the problem can be included under the word "transportation". For instance Dr. Corless said, "The few geological explorers who have penetrated to these remoter regions . . . . . . have as a rule been compelled to stick closely to canoe routes,"; Dr. Goodwin remarked, "This barren Laurentian granite, which is put down on the maps as covering the greater part of this area, is the best guess the geologist could make from travelling along watercourses Within the next few years . . . . . . the Timiskaming and Northern Ontario railway will undoubtedly be extended to James Bay . . . . . . In order that we may be prepared for the probable influx of prospectors when transportation facilities to tidewater are provided, I think all available information on this district should be gathered together in handy form." All three-Corless, Goodwin and Cole-emphasize the well-known fact that explorers, geologists and prospectors working in new country must stick to the watercourses and that transportation by rail, road or water has always been the all-important deciding factor in facilitating the exploration and development of remote districts. Dr. Corless did, however, suggest other means of transportation in stating, "The aeroplane will be of assistance in future study of some parts of these remote areas."

Jan 1, 1924

By X. W. Yi, Z. J. Li, G. W. Ma

In this paper, the compressive strength and failure patterns of reinforced cemented paste backfill (CPB) were studied aiming to promote the stability of backfilled stopes. The concept of ductile backfill was proposed and a series of unconfined compression tests were carried out on both non-reinforced and reinforced cemented paste specimens. Portland cement (3% to 5% by weight of tailings) and five different types of ductile materials (0 to 0.5% by weight of solids) were employed in this experiment for the specimen preparation. The test results showed that inclusion of ductile materials enhanced the unconfined compressive strength (UCS), reduced the post peak stress loss and transformed the failure behaviour of specimens from classical brittleness to ductility. The strength of CPB reinforced with different proportions of polypropylene fibres was compared. The stress-strain curves illustrated that both cement and fibres contributed to the increase of UCS, but higher strain values at the peak stress were achieved by fibre reinforcement. CT sliced images acquired from X-ray computed tomography (CT-scan) demonstrated that the reinforced specimen developed irregular crevices at the edge of cross sections and gained the capacity of bearing large displacements owing to the mobilised tensile strength of fibres. It leads to the potential of avoiding unexpected falling blocks of CPB when adjacent mining occurs. This finding highlights a strategy to improve the self-supporting capacity of the fill mass with less cement usage and reduce the ore dilution rates when excavating to adjacent stopes.

Jan 1, 2015

By S. S. Sephton, Kirit C. Vyas, Melvin J. Greaves

Energy requirements for various pelletizing systems are considered from a fuel and power aspect, with the presentation of typical energy heat balance flow sheets. A partial calculation for the firing zone of a straight grate system is shown and a comparison of an actual measured and a theoretical-calculated heat balance for a grate-kiln is presented. The power used for each pelletizing system and future possible energy savings a1•e also reviewed.

Jan 1, 1976

By Jiuhua Xu, Shuiku Jia, Weiren Sun

"Abstract -The Jinqingding gold deposit, situated in the east Jiaodong Peninsula of Shandong province, is typical of the pyrite-quartz vein gold deposits in the Muping-Rushan gold belt of China . The gold deposit is controlled by a great NNE fracture zone and is composed of several lenticular orebodies within the fracture zone occurring in the Kunyushan granite massif. The Kunyushan granite massif was formed by the replacement of the Archean Jiaodong group.The main minerals associated with gold are pyrite, chalcopyrite, galena and sphalerite; the gangue minerals are dominated by quartz, sericite, microcline and calcite. The mineralizing event can be divided into four stages: (1) pyrite-quartz; (2) quartz-pyrite; (3) siderite-polymetallic sulfides; and (4) calcite-quartz. Gold occurs mainly as native gold and electrum in stage 1 and stage II. There are some evident differences between pyrite from major stages of gold mineralization and that from minor stages; these include differences in crystal forms, size and composition of fluid inclusions.Wallrock alterations consist of sericitization, silicification, pyritization and potash-feldspar alteration. Five alteration zones can be distinguished from unaltered granite (zone 0) to vein lodes (zone IV). Au and Ag increase rapidly from zone 0 to zone IV, Cu increases continuously, while Pb and Zn increase slowly. R-type geological factor analysis indicates that the Au, Ag, Cu, Pb and Zn bear a close relationship to wallrock alteration."

Jan 1, 1994

By Fred C. Bond

A study of the settling and thickening of finely divided pulps was undertaken with the object of obtaining certain fundamental relationships, with resulting improvements in the design and operation of mechanical equipment. The subject has been treated in two parts: testing and batch thickening, and continuous thickening, including calculations of capacity and dimensions. Part 1. ? Testing and Batch Thickening The usual method of making thickening tests is to agitate the pulp with a plunger in a graduated glass cylinder and let it settle, while recording the time rate of settling. The settling rates corresponding to different pulp dilutions are found, the ultimate dilution obtained is measured, and the necessary thickener area in square feet per ton of dry solids per 24 hours is calculated, for each pulp dilution. The largest area found is used in selecting the proper thickener size.

Jan 1, 1946

By F. Pinto, C. A. Prato, R. J. Rocca, P. F. J. Huerta Soaje

"The seismic hazard for civil engineering structures is generally defined in terms of deterministic or probabilistic acceleration response spectra at an equivalent rock outcropping. The design of tunnels, however, requires the definition of demands in terms of accelerations at ground surface (near the portals) and in terms of both accelerations and velocities at different depths within the alignment. The design near the portals is controlled by inertial effects and is often times impacted by the possibility of slope instability and rockfall, whereas the design at deep sections is controlled by kinematic effects. These effects are accounted for in practice by introducing deformation patterns in the structure that are related to an assumed wavefield, often times ignoring the effect of the structural stiffness in the response. This paper presents a study regarding the definition of seismic demands for different sections of 14-km long tunnel in the Andes (Argentina-Chile), with a maximum overburden of 1750 m in a seismically active region. The tunnel will pass through volcanic massifs mainly composed by andesites and rhyolites.The study includes the definition of spectrum-compatible seismograms, deconvolution, and definition of accelerations and peak particle velocities for different overburden conditions. A kinematic interaction study for a 500-m tall ventilation chimney shaft is also described, where a simple formulation for the interaction analysis is considered in order to more accurately evaluate shear and bending demands. INTRODUCTIONThe seismic design of linear underground structures, such as shafts and tunnels, generally considers the inertial forces near the shallow sectors (e.g., portals) and the kinematically imposed deformations for the deep sections (e.g., Hashash et al. 2001). The inertial forces are often times evaluated on the basis of design spectra recommended by seismic hazard studies. The kinematic demands for the deeper sections, however, needs to be defined in terms of additional information which is not always indicated by the seismic hazard studies, e.g.; peak particle velocities and accelerations, and their variation with depth. These parameters can be determined by means of a site response analysis, whereby outcrop motions can be deconvoluted in order to evaluate motions inside the ground mass (e.g., Schnabel et al., 1972). Hashash et al. (2001) defines factors that may be used in order to account for attenuation of motions inside the ground mass. However, these factors are provided for depths up to 30 m only, whereas depths of tunnels structures can range up to thousands of meters."

Jan 1, 2015

By F. Ajersch, M. Rigaud, M. Jallouli

"Le gonflement des boulettes d'hématite à été étudié à l'aide d'une méthode de mesure standard ISO ainsi qu'à l'aide d 'une méthode de mesure dilatométrique.La première méthode a servi à l'étude des boulettes haute silice (5% SiO2) dont l'indice de basicité (IB = CaO + MgO -i- SiO2 + Al2O3) a été ajustée soit à l'aide d'une addition de dolomie, soit à l'aide d'une addition de pierre à chaux, soit à l'aide d'une addition de ces deux composes. L'indice de basicité variait de 0.05 à 0.12. Les résultats de gonfle ment obtenus à 1000?C dans une atmosphère de 40 CO - 60 N2 ont permis de montrer qu’indépendamment de l'indice de basicité c'est la dolomie qui contribue le plus à diminuer le gonflement par rapport à la pierre à chaux. L'utilisation de l'indice de basicité comme critère de sélection des boulettes est discutée.La méthode dilatométrique a servi à l'étude du gonfle ment de deux types de boulettes préparées à partir de deux concentrés de fer et dont la teneur en silice a été fixée à 2.5% et 0 5%. Ces deux types de boulettes ont reçues les mêmes additions de liant en quantité et en nature. La détermination en continue du gonflement, à 950?C dans 40 CO - 60 N2, a permis d'une part de mieux cerner le niveau de réduction auquel correspond le maximum de gonflement et d'autre part de montrer que l’allure des courbes de gonflement est étroitement liée à la nature du liant. Une augmentation de la teneur en silice des concentres contribue à diminuer le gonflement des boulettes.Des essais de réduction de gonflement non isothermes ont été réalisés à des montées de température à 10 et 20?C/min. Les résultats indiquent que le gonflement déterminé dans les conditions non iso thermes est inferieur à celui obtenu lors des essais isothermes. On discute alors de la validité des essais standards de gonflement qui sont utilisés pour prédire le comportement des boulettes lors de leur réduction dans un haut fourneau."

Jan 1, 1983

By J. L. Jobe

In planning the operation of a new mine or new sections of an operating mine, due provision must be made for the ultimate recovery of as much of the seam as is consistent with safety and economic principles. Each mining district and, indeed, each seam, especially in mining under submarine conditions, has individual problems which render hard and fast rules under all conditions of mining impossible. However, certain basic principles can be applied to all seams under specific conditions. In all mines, the two basic methods of mining, 'longwall' and ?room-and-pillar? or their variations, can be adopted, but certain fundamental factors must be analyzed before either method is finally applied to the extraction of the seam. The factors which enter into the successful, safe, and economic extraction of all seams are, briefly stated, as follows: (1) Character and thickness of the seam. (2) Character of the floor and immediate roof of the seam. (3) Composition, strength, and thickness of the overlying beds to the surface. (4) The depth of cover to the surface or sea bottom. (5) Conditions under which the seam is mined (land or submarine area). (6) Pitch of the seam. (7) Economic value of the seam. (8) Mining laws.

Jan 1, 1947

By R. R. Rogers

Abstract The degree of cathodic protection of steel and the anode corrosion rate were determined when anodes and waters of different compositions were used at temperatures similar to those in domestic hot water tanks. Twenty different anode materials, sixteen of them magnesium-zinc-aluminium alloys, were immersed in six different synthetic waters resembling those to be found in various parts of Canada. The results showed that (1) both the degree of cathode protection and the average anode corrosion rate are affected materially by the composition of the anode material and of the water; (2) poor cathode protection is associated with low anode corrosion rate; (3) when the cathode is fully protected, the anode corrosion rate may be comparatively low or comparatively high, depending upon the composttion of the water; (4) an important relationship exists between the magnesium content of the preferred anode and the composition of the water; (5) the degree of protection is increased as the SO4 + Cl concentration of the water is increased and thus as its specific resistance is decreased. Introduction Fairly recently, the use of the active metal magnesium for the cathodic protection of less active metals has received a considerable amount of attention. This interest has been stimulated by the fact that the wartime demand for magnesium was greatly in excess of the present peacetime demand and there is a natural desire to continue operating the large magnesium plants which were built during the war. Information regarding the use of zinc and aluminium for this purpose also has been published. There is a great demand for domestic hot-water tanks which will resist corrosion satisfactorily. This problem is rather complex in view of the fact that the composition of the water used in such tanks varies greatly and depends upon the locality. The present investigation deals with the effect of water composition and anode composition on the cathodic protection of steel under conditions approaching those which exist in hot water tanks.

Jan 1, 1948

By T. Shellhammer, A. Park

Among all pure metals, copper has the second highest thermal and electrical conductivity, next to silver. These properties coupled with a reasonable cost, make copper ideal for use in metallurgical vessels as a conductor of electrical current, as well as a lining material and protector of refractories and steel superstructures. Treatments of copper to address it’s softness and low melting point, specifically hard surfacing and calorizing, will be discussed. This paper will cover the evolution of copper to its current form, offer comparisons to other materials, and theoretical and empirical evidence on its superior performance in metallurgical vessels such as blast furnaces, basic oxygen converters and electric arc furnaces. Some case studies will be provided and finally a brief summary.

Jan 1, 2015

By Joseph Sawicz

By now, the concept of remotely controlling heavy equipment in underground mines has become commonplace. Personnel safety is the biggest justifier for remote control, followed by an inherent cost saving (in certain cases) when wireless video is added to the mix. There are a handful of vendors targeting this need, and for years the mines have remained loyal to their brand. But as the number of remote-control related accidents and maintenance costs increase it forces our industry to take another look at this commonplace concept. And as the blinders are taken off, the mines are getting the revelation that not all remote control systems were created equally. This paper highlights the differences between various remote control systems, and then moves into an in-depth look at HARD-LINE?s package which drastically cuts maintenance costs, and also provides a solid investment toward full Tele-operation.

Apr 1, 2005