Search Documents

By J. Contreras

In the period 2003-2004, the situation of the copper concentrate market was unfavourable for smelters and refineries, with low TC/RC values and euro-dollar parity affecting European companies negatively. Within this scenario, Atlantic Copper decided to develop a plan to increase its competitiveness and to improve its results in these market circumstances. The plan affected all departments in the Company and was based mainly on cost reduction in energy and manpower. A general analysis of the Complex's overall efficiency was carried out and, based on this analysis, two major Projects emerged, "Primavera" and "KF". Each Project consisted of smaller sub-projects which aimed at improving the areas which could perform better according to our general analysis. The paper describes how this entire project developed and the final results obtained by the Company.

Jan 1, 2007

By S. Mohammadnejad, M. Olizadeh, B. Mehrabi

A new method using a combination of comprehensive mineralogical and analytical approach which includes optical and electrical microscopy and several analytical techniques with diagnostic leaching has been used to characterize the associations and distribution of gold in a variety of minerals from the Zarshuran refractory gold ore, NW Iran. Zarshuran ore with an average of 7.9 g/t Au-grade and about 8% arsenic with gold recovery less than 20% in direct cyanidation is considered as high arsenic, high au-grade refractory gold ore. In most of the refractory ores, gold is associated with arsenopyrite and co-para genetic ore minerals, while in Zarshuran ore; gold is associated with orpiment, realgar and arsenian-pyrite. Considering its mineralogy and As content, it can be considered as the most difficult refractory ore for characterization and processing. Results from the mineralogical examination and diagnostic leaches indicate that there is only a small amount of free gold (17-19%) that is present in cyanide-soluble sulfo-arsenides compounds, predominantly orpiment and realgar. Diagnostic leaches also indicate that little gold is occluded within the silicate structure (14%). Overall, the gold is mostly included in sulfides, arsenic sulfides and sulfo-arsenides (50%). The results also have shown how the technique can be used to gain a good initial understanding of potential metallurgical problems for a refractory gold ore.

Jan 1, 2005

By J. L. Miller, R. W. Burns

This paper sets out the various phases of bringing a merchant bar mill into operation from feasibility consideration through financing, design and scheduling to completion.

Jan 1, 1967

By James D. Bittner

Separation Technologies, LLC (ST) has developed a processing system based on triboelectric charging and electrostatic separation that provides the mineral processing industry a means to beneficiate fine materials with an entirely dry technology. The environmentally friendly process can eliminate wet processing and required drying of the final material. The process requires little if any pre-treatment of the material other than grinding and operates at high capacity ? up to 40 tonnes per hour by a compact machine. Energy consumption is low, approximately 1 kWh/tonne of material processed. Since the only potential emission of the process is dust, permitting is typically relatively easy. In contrast to the other available electrostatic separation processes that are typically limited to particles greater than 75 µm in size, the ST belt separator is ideally suited for separation of very fine (<1 µm) to moderately coarse (300 µm) materials with very high throughputs. The triboelectric particle charging is effective for a wide range of materials and only requires particle ? particle contact. The small gap, high electric field, counter current flow, vigorous particle-particle agitation and self-cleaning action of the belt on the electrodes are the critical features of the ST separator. The high efficiency multi-stage separation through charging / recharging and internal recycle results in far superior separations and is effective on fine materials that cannot be separated at all by the conventional electrostatic techniques. Since 1995, this triboelectric process has been extensively used for the beneficiation of coal fly ash with eighteen separators in place and over 130 machine-years of operation at locations in North America and Europe. ST has also installed separators for the beneficiation of industrial minerals in North America and Europe. The technology has been successfully applied to the beneficiation of a variety of minerals including calcium carbonates, talc, barite, and potash.

Aug 1, 2013

By Brian W. Mackenkzie, Jozef Lajzerowicz

This paper is intended to familiarize planners in the noncommunist world with the district planning approach used in eastern Europe for mining development. It deals generally with the basic nature of the district planning problem, the planning process for mining development and the state organization for the planning of mining districts. A number of applications of district planning techniques to both established and new eastern European mining districts are described.

Jan 1, 1971

By D. R. BUDINSKI

Clinton Creek Mine in west-central Yukon produced 0.94 million tonnes of fibre from 15 million tonnes of asbestos ore between 1968 and 1978. The mine closed in 1978. The deposit lies along the margin of a medium sized ultramafic pluton that intrudes schistose and gneissic rocks of the Yukon Metamorphic Complex. Country rocks are metamorphic equivalents of a mixed sedimentary and volcanic assemblage deposited during Precambrian or early Paleozaic time. Movement along the north west-trending Tintina Fault System probably caused the fairly high meromorphic grade that altered the original rocks to schists and gneisses. The ultramafic pluton hosting Clinton Creek Mine is one of several bodies that were emplaced along a deep seated imbricate fault system parallel to the Tintina Trench. Most of rhe intrusions were hydrothermally altered to serpentinite, bur apparently only the one at Clinton Creek contains commercial quantities of asbestos. The Clinton Creek pluton was probably injecred slowly at relatively low temperatures into the crustal rocks as a "mush" that cooled gradually, allowing sufficient time for serpentinization and chrysotile fibre crystallizarion.

Jan 1, 1984

By D. Bai, F. Hamad, S. Abraham

For the integrity of welded structures such as pipelines, the toughness of the heat-affected zones (HAZ) is an important property. This property is often specified in terms of Charpy V-notch (CVN) impact toughness and determined by the standard test method. An experimental study has been conducted in an industrial laboratory to measure the impact toughness of the coarse grain heat-affected zones (CGHAZ) of an X80 line pipe material. The field girth welding conditions in terms of heat input were simulated, together with special edge preparation to improve the targeted testing of the CGHAZ. The effect of toughness of the neighboring regions, in particular the weld metal, on measured impact toughness of the CGHAZ was investigated. The fracture paths of the CVN tested samples were examined by both optical and scanning electron microscopy. The deviation of segments of the fracture path into the weld metal was found to have a significant effect on the measured impact toughness of the CGHAZ.

Jan 1, 2005

By W. M. Tupper

Municipal governments recognize the importance of aggregates in the local economy and the need to manage this resource in the interest of the public good. They have encountered problems with regulating the industry and the dichotomy between the urban need and the rural source. They have suffered from a lack of financial benefit, an adequate aggregate inventory, provincial strategy, economic information and public understanding. A provincial strategy for ensuring the availability of aggregate supplies to developing areas of the Province is essential. The Province should also be responsible for licensing, research, technical expertise on rehabilitation, public education and financial assistance. Upper-tier municipalities (regions or counties) should assume responsibility for resource management, including resource availability, demand characteristics, truck routing, phasing of resource development and sequential land-use planning. Area municipalities (towns and townships) can best determine the social and environmental impact of a specific aggregate development proposal and should therefore have the primary responsibility for the location of new pits and quarries. They should also have the authority to supplement provincial regulations concerning operating standards and the phasing and standards of site rehabilitation.

Jan 1, 1978

By M. Harrison, C. H. Stockwell

"Metals vah1ed at more than $200,000,000 have been obtained, mainly since 1930, from the mines of northern Manitoba. The greater part of this production has been copper, zinc, and gold from the Flin Flon, Sherritt Gordon, and Mandy mines. The chief mines from which gold alone has been produced are God's Lake, Laguna, and Gurney. At present (May 1947) Flin Flon and Sherritt Gordon are the only producing mines, but the Nor-Acme property is being developed for large-scale production of gold. Large deposits of nickel and copper are being diamond drilled at Lynn Lake, and the Thompson, Ferro, and other properties are being developed. The mineral deposits lie within irregular or elongated areas of Precambrian sedimentary and volcanic rocks, surrounded by granite ( Fig. 1).The common rock types include basic and acidic flows, agglomerate, ruff, greywacke, arkose, argilli te, conglomerate, and their gneissoid and schistose derivatives. They are invaded by sills, dykes, and irregular bodies of gabbro and diorite, and all are cut by granite. Some of the sediments are interstratified with volcanics, and others are deposited unconformably on them.STRUCTURAL GEOLOGYLittle is known of the structures of the rocks in the area as a whole, because by far the greater part is unexplored or has been covered only by reconnaissance surveys. Available information indicates a general east structural trend in the southeast part, whereas in the west part the folding is mote complex with no definite overall trend. However, in a few small areas in the western part where detailed work has been done, as around the Flin Flon, Sherritt-Gordon, Nor-Acme, and other properties, the structure is fairly well known. The following descriptions apply chiefly to these areas ."

Jan 1, 1954

By Claude K. Howse

The area covered by the present paper consists of about fifty square miles in the immediate vicinity of the settlement of St. Lawrence, which is on the Southern extremity of the Burin peninsula on the south coast of Newfoundland. Physiography Physiographically, the area is part of the Atlantic upland, equivalent to the New England province of the United States. Evidences of two erosion surfaces are to be seen truncating the intrusives and the folded volcanics and sedimentary rocks. The older erosion surface is represented by small monadnocks from 650 to 750 feet in height with the younger surface covering most of the area and characterized by rounded subdued topography with maximum relief of two to three hundred feet and numerous ponds and bogs. These surfaces have been correlated with the High Valley and the Lawrence peneplains of Newfoundland. On the Avalon peninsula, these peneplains have elevations of, respectively, from 1,300 to 1,700 feet and from 500 to 1,000 feet. Glaciation The entire peninsula has been glaciated, with lee-and-stoss slopes showing on the highest hills in the immediate vicinity, many of which have striae and erratics on their summits. The lee-and-stoss slopes, the glacial striae, and the distribution of certain rocks found in the drift and whose source outcrops are known, indicate a southward direction of ice movement.

Jan 1, 1951

By Kristine Haug

Although most in situ operations in Alberta do not encounter significant problems during resource extraction, there have been a few documented occurrences of oil or steam releases as a result of compromised caprock seals. The objective of the Oil Sands Caprock Integrity Project (OSCRIP) is to characterize the units above and below bitumen zones to determine which geological factors affect the quality of the caprock seal. In addition, geomechanical properties and stress measurements of the bitumen reservoir and overlying units will be examined to provide a better picture of the containment conditions in which in situ operations occur. The information from this study will aid regulatory staff and industry in determining the zone-specific geological and geomechanical factors that could affect the design, operation, and feasibility of in situ recovery projects. The OSCRIP study area (Townships 87 to 99 and Ranges 1 to 13, West 4th Meridian) encompasses the surface mineable area, the northeast extent of the Wabiskaw-McMurray bitumen deposit and the Clearwater Formation, as well as a wide band of the Devonian salt-dissolution zone. Regional geological mapping of the Cretaceous strata focuses on the spatial extent and thickness of the caprock seal. Mapping of the underlying Devonian strata is targeted at better understanding the potential effects of salt dissolution and collapse of overlying strata on the integrity of the caprock seal. Examination of LiDAR (Light Detection And Ranging) bare earth DEM in the study area has revealed localized depressions that may represent sinkholes rooted in subsurface collapse features in Devonian carbonate and evaporite strata. Mapping the location and understanding the timing of salt dissolution-related features and deformation in the Devonian strata will help address questions about the possible effect that geological structures, such as sinkholes, have on the integrity of the caprock, as well as the potential for localized variations in the stress regime of the bitumen zone and overlying units. The stress regime in units above 350 m is such that any induced fractures are believed to be horizontal, and therefore, there would appear to be no mechanisms that would allow these fractures to reach the surface. However, recent incidents have shown that vertical pathways can occur, linking the subsurface to the surface. The final phase of the project will evaluate the changes that may occur in the stress regime under thermal operating conditions in the study area.

Jun 1, 2012

By J. H. Walsh

IN THE DEVELOPMENT of procedures for the separation of minerals, the choice of reagents for flotation is frequently determined by the extent to which a given mineral is wettable by water. Measurements of the contact angle of an air bubble on wet mineral surfaces are often used in the laboratory to estimate the wettability of the surface. For the results of these measurements to be reproducible, the surface of the mineral must be polished to a mirror-like smoothness and must be free from oily contamination. Elaborate procedures for preparing mineral surfaces have been developed by Wark ( 1) and Taggart (2), and these procedures have been generally accepted as adequate for their purpose. The polishing techniques, how-ever, have certain inherent disadvantages which make it impossible to assess the effects of polishing, entrained abrasive, and adsorbed gases on the wettability of the mineral surface.

Jan 1, 1957

By Corinne Boone

CO2e.com, LLC - launched in November 2000 - aims to be ?the global hub for carbon commerce.? CO2e.com is a subsidiary of the Cantor Fitzgerald Group, one of the world?s leading brokerage firms Recent Investor in CO2e ? Mitsui & Co. Alliance with Cantor Fitzgerald Environmental Brokerage Services Group (CFEBS) Offices in London, Toronto, Tokyo, New York, San Francisco, Los Angeles, Connecticut, Houston Primary Goals/Benefits of ET § Goals of Emissions Trading: ? Permit Industrial Growth/Expansion ? Promote Economic Efficiency and Flexibility in Meeting Air Pollution Standards § Benefits of Emissions Trading: ? Enhance Air Quality w/o Economic Stagnation ? Encourage Development of New Technology ? Foster Most Efficient Use of a Limited Resource -- Clean Air § Contributes to Sustainable Development and objectives of UNFCCC, Kyoto Protocol?.

Nov 1, 2002

By M. Aushouri, S. H. Mansouri, N. Aminizadeh

A thermo-chemical model of the Peirce-Smith copper converter in blowing the copper stage has been developed to predict the molten temperature. The key assumption of the model was that white metal and gas phases in the converter were in thermal and chemical equilibrium. In this model, the chemical reaction of white metal and oxygen was accomplished completely. So long as sulfur existed in the bath, the generation of Cu2O was frozen. The reaction rate was considered to be constant and controlled by the reacted sulfur. The converter temperature was calculated by heat balances over time. The model was validated by a detailed comparison with measured industrial data. A good agreement was obtained. The converter temperature depended on process parameters such as oxygen efficiency, molten emissivity and oxygen enrichment.

Jan 1, 2007

By H. Aminian

Gold powders have many important industrial applications. In this paper the available processes for the preparation of gold nano and micron sized powders are described. The attention has been given to hydrometallurgy route and the recent works and achievements in controlling the powder morphology are highlighted.

Jan 1, 2011

By Yusuke Yamamoto, Mineo Asano

"The present study investigated the texture transition during secondary recrystallization in the AA5182 sheet. During the initial stage of annealing, the texture showed a weak Cube orientation as the primary recrystallization texture. During the secondary recrystallization with abnormal grain growth, the area ratio of the {hkl} <011> orientations increased by consuming the other orientations. The texture transition was calculated by the 2-D Monte Carlo simulation with the misorientation dependency. When the higher grain boundary mobility was set in the specific range of the high angle misorientation, the orientation preferential growth of the RW {100} <011> orientation was reproduced. However, other {hkl} <110> orientations could not be well reproduced by the misorientation dependency.INTRODUCTION Crystal orientation and texture are important factors for aluminum sheet products from the standpoint of mechanical property, formability and isotropy. The recrystallization texture results from the orientation preferential growth from the rolling deformation microstructure and the texture (Alvi, Cheong, Suni, Weiland, & Rollett, 2008). Texture development has been a topic of intense research for decades with advances in analysis methods, e.g., orientation mapping (OIM) and computer simulations (Fjeldberg & Marthinsen, 2010; Ivasishin, Shevchenko, Vasiliev, & Semiatin, 2006). The grain boundary characteristic is considered to be a key for the orientation preferential growth. In the case of the recrystallization from the deformed microstructure, not only the grain boundary characteristic, but also the dislocation density and the subgrain size affect the nucleation and the grain growth (Engler, Löchte, & Hirsch, 2007). On the other hand, in the case of secondary recrystallization, the dislocation density and the subgrain size can be ignored and the effect of the grain boundary characteristic can play a significant role in the grain growth. There is intense research about the texture development during secondary recrystallization in aluminum alloys and it was reported that coarse {hkl} <011> grains were formed during the secondary recrystallization (Suk, Shin, & Huh, 2006; Rios, & Gottstein, 2001). However, the mechanism of forming the {hkl} <011> grains has not been fully clarified. In the present study, the effect of the grain boundary characteristic on the orientation preferential growth was investigated by EBSD analysis and Monte-Carlo (MC) simulation."

Jan 1, 2018

By A. R. Khodabandeh, T. Nematkhah

Correct selection of forging parameters is very important to produce sound superalloy parts. In this investigation nickel-iron base superalloy IN901 successfully forged and seal spacer, which is a part of airplane with about 11 kg weight has been produced. Forging has been performed on the basis of hot compression results, which show deformation above 1100°C associated with dynamic recrystallization (DRX) which can increase the workability of material. On the other hand annealing at 1100°C decreases the flow stress during hot compression, and then increases the material formability. Then billets annealed at 1100°C in electrical furnace for 24 hours and reheated again to 1100°C before forging. Initial square cross section billet with 128mm side and 202mm length forged immediately after reheating by 80MN mechanical press. Specimens forged in five steps: upsetting, three steps molding and finishing. Preformed and molded specimens reheated in electrical furnace before later step of forming. Finally specimens trimmed by 1 OMn mechanical press and hot set by hydraulic press and then cooled in air to room temperature. Results show that reheating temperatures has been selected correctly because there isn&apos;t any surface crack and die cavities filled completely by forging material. Material flow has been carried out properly and there isn&apos;t any defect in critical points especially in extradoses and intradoses. Microstructural examinations show that grain boundaries contain Ti-rich globular particles that formed during cooling.

Jan 1, 2006

By V. G. c Papangelakis, M. Huang

A conductivity cell, developed previously, was employed in an effort to investigate the inter-relation between electrical conductivity and acidity of sulphuric acid - metal sulphate solutions at high temperatures. The measured solutions include the H2SO4-H2O, MgSO4-H2O, H2SO4-MgSO4-H2O, H2SO4-MgSO4-Al2(SO4)3-H2O solutions. All solutions reported in this paper were measured from 15 to 250 °C at equilibrium vapour pressure. The maximum measured concentrations of H2SO4, MgSO4 and Al2(SO4)3 were 0.45 m, 0.30 m and 0.10 m, respectively. It was found that, from 15 to 250°C, there is a linear relationship between H2SO4 concentration and electrical conductivities for acid concentration up to 0.45 m. At 250 °C and constant H2SO4 concentration, the solution conductivity drops with the increase of MgSO4 concentration. Lt is suggested that this drop is caused by a decrease in the concentration of H. Finally, an empirical model was developed based on the available measurements. This model has been tested against real laterite leach solutions where sulphuric acid and metal sulphates are dominant electrolytes. The average difference between the estimate acid concentration from this model and the one from titration was less than 5%.

Jan 1, 2004

By S. G. Enns, E. W. Yarrow

"Situated about 200 km southeast of Juneau, Alaska, within the lower Stikine River region of northwestern British Columbia, the Galore Creek porphyry Cu-Au deposits are hosted by Upper Triassic to Lower Jurassic alkaline volcanic rocks and comagmatic syenite intrusions. Early and late breccias are also locally important host rocks for mineralization. Of the twelve identified Cu-Au deposits, the most important are the Central zone, Southwest zone and the Junction deposits with a combined resource of 284 million tonnes at 0.67 % Cu.The composition of the intrusive rocks is predominantly silica-undersaturated, alkaline, and metaluminous. Four intrusive suites are identified from field, petrographic and petrochemical data. Variation within suites or lineages can be explained by alkali feldspar fractionation. An oscillation between porphyritic and equigranular intrusions is suggested by the sequence of different intrusive lineages. The youngest intrusive phase is silica-saturated.A complex succession of intrusive and hydrothermal events is demonstrated at Galore Creek, with the most intense alteration and mineralization developing early in its history. In the Central zone, early Ca-K-silicate alteration, dominated by garnet, biotite, Kfeldspar, and anhydrite grades outward into K-silicate alteration. Both are locally overprinted by retrograde sericite± anhydrite± carbonate (SAC) alteration. The most intense Ca-K-si/icate alteration, a magmatic-hydrothermal breccia, and an early syenite intrusion are all coincident with copper mineralization in the core region of the Central zone. However, higher grade mineralization in the zone, exceeding 1 % Cu with more than 0.5 g/ t Au, is typically associated with intense biotite-rich, K-silicate alteration primarily hosted by altered volcanic rocks. The highest gold grades, commonly exceeding 1 g/t, are associated with bornite-rich mineralization situated in the northern and southern parts of the Central zone.Mineralization in the Southwest zone occurs as disseminated chalcopyrite within a late, diatreme breccia and adjacent K-feldspar porphyry. In the other satellite deposits, disseminated chalcopyrite and bornite occur in volcanic rocks with alteration that is similar to the Central zone."

Jan 1, 1995

By John Galbraith, Dwayne D. Tannant, Chris C. Langille

"Development of underground openings in a deep mining environment requires a support system that is able to absorb energy as a result of dynamic loading due to rockbursting and blasting and static loading due to convergence as the development face advances. The support system must be resistant to corrosion and be effective over the life of the excavation, upward of ten years, yet simple and cost effective to install. Over the past two years, research has been conducted at INCO’s Creighton Mine to try and identify a one-pass grouted support system that will meet these needs.The main problem faced, with simply using grouted rebar at depth, is the effect of tunnel convergence on the stiff grouted bolts. Typically, if fully grouted, stiff rebar are installed to the face of an advancing development heading, the amount of convergence that occurs can result in failure of the bolts at the face plates used to attach the mine screen to the back. An initial support is required to enable crews to continue the bolting cycle in the immediate term, yet allow for this convergence over the longer term as the drift advances. The ideal support system will allow both to occur, giving effective immediate support while providing long-term effectiveness in allowing convergence to occur while maintaining the capacity of the bolt.This paper will investigate the expected convergence in deep development headings at +2200 m (+7200 ft) through the use of direct measurements using both flex rod extensometers grouted into the back of a development heading and five-point tape extensometer stations. Measured results will be compared with simple2-D numerical analysis to evaluate the anticipated convergence expected to be absorbed by the bolting system. The required convergence will then be compared with load deformation response of several support configurations."

Jan 1, 1996