Search Documents

The cost benefits of controlling dilution of extracted ore have been very well understood by miners and mining professionals for many years. However, as we strive towards more mechanization, the dilution factor has been compromised in order to fit ?equipment? that is better suited to provide improved safety and productivity. Alternately, the drilling and ground support is accomplished by handheld drilling. In 2007, a short study, commissioned by CAMIRO (Canadian Mining Industry Research Organization) on the safety of hand held drilling vs. mechanized drilling, concluded that the risk of injury with handheld drills was seven times greater than with mechanized drills. Armed with this data, MEDATech Engineering proposed to the CAMIRO group to fund development of a ?MICRO Bolter?.

May 1, 2009

By Ross G. Bertinshaw

"The Line Creek Mine of Crows Nest Resources started mining coal in the fall of 1981. There are seven mineable seams with thicknesses ranging from 1.5 to 13 metres and with dips varying from 0 degrees to 60 degrees. This, together with internal partings and the very friable nature of the coal, creates a number of mining problems.The coal is divided into zones depending on the dip of the seam. Each zone requires a different mining technique to ensure optimum recovery and low dilution while still keeping fines to a minimum.Line Creek employs a combination of hydraulic front shovels and backhoes to mine its coal without blasting or use of dozers. This has been very successful in reducing the proportion of fine coal hauled to the plant, thus improving quality control and reducing costs in coal processing.There have been a number of other benefits from the use of excavators instead of more conventional methods. These include better selectivity, good cleanup, reduction in traffic at the face and lower cost.IntroductionThe Line Creek Mine is situated approximately 25 km north of Sparwood in southeastern British Columbia (Fig. I). Preproduction stripping began in J98J with the first coal shipments made in 1982. In 1983 the mine produced 2.1 million tonnes of raw coal.Similar to other East Kootenay coals, the seams at Line Creek are characterized by their friability, producing a large proportion of fine coal during mining. In an attempt to reduce these fines Crows Nest Resources has instituted the use of hydraulic excavators to mine and load the coal.Hydraulic excavators offer other substantial advantages over front-end loaders and dozers, which has been the conventional system in other mines in the area."

Jan 1, 1985

By Raymond D. Potts

"Minntac is a taconite mining, concentrating and pelletizing operation located near the town of Mountain Iron, Minnesota, U.S.A. It is totally owned and operated by USX Corporation and represents its largest source of domestic iron units. Minntac began producing fluxed pellets in 1988 and has produced both acid and fluxed pellets since then. This paper compares the acid and fluxed pellets produced at Minntac. It reviews modifications that have been made to the plant flowsheet and discusses areas recognized for improvement since the beginning of fluxed pellet production. It also comments briefly on the performance of Minntac fluxed pellets in USX blast furnaces and the future of fluxed pellets at Minntac.IntroductionMinntac was built in three steps with each step designed to produce 6 million long tons of acid pellets per year. The actual production has varied though. Figure I shows the production by year at Mirmtac. Step I began production in 1967, Step 2 in 1972 and Step 3 in 1978. Mirmtac produced 16.5 million tons in 1979 but only 3.5 million tons in 1982 when the facility was shut down for six months because of the lack of demand for pellets. Since the initial start up, Mirmtac has produced over 200 million long tons of pellets. Until 1987, all the pellets produced were ""acid"" pellets. In 1987, equipment to produce ""fluxed"" pellets was installed and tested. In 1988, full scale production of fluxed pellets began."

Jan 1, 1991

By M. Saghaeian, R. Hejazi, Sheikhzadeh. V., A. Abazarpoor

"The morphology of iron ore concentrate particles is known to influence several properties of iron ore pellets, including drop number, compression strength, and reduction properties. This study aimed to determine why grinding methods and particle morphology influence green pellet properties. Particle morphology can be directly related to the grinding method: ball mill (BM) or high pressure grinding roll (HPGR). In this research, two iron ore concentrates, namely Gol-e-gohar and Ardakan, were ground by a BM and HPGR to produce a suitable Blaine value for pelletizing (nearly 1,900 cm2/g). Morphological features of particles were subsequently investigated by sieving and cyclone sizing for particle size distribution, the Brunauer-Emmett-Teller (BET) and Blaine methods for specific surface area (SSA) and scanning electron microscopy (SEM) for the evaluation of shape descriptors. It was concluded that HPGR resulted in generating a greater proportion of fine particles compared to ball milling. The BET results showed that the SSA of HPGR pellet feed was higher than that from the BM due to a greater proportion of cracks, indents and bulges and the creation of new fracture surfaces. SEM images processed by ImageJ software indicated that particles ground by the BM tended to be more rounded and less elongated than HPGR particles because of the breakage model of each method. To show the effect of morphology on the green pellet quality, green pelletizing was performed in a pilot pelletizing disc. The HPGR pellet feed had a higher drop number in comparison to the BM pellet feed, due to the angular and rough shape of the particles.INTRODUCTIONThe demand for fine or ultra-fine particles as feed material for ceramics, composite materials, and mineral processing is on the rise (Kotake, Kuboki, Kiya, & Kanda, 2011). The final concentrate of iron ore processing plants (filter cake) has a size range roughly between 0 and 300 µm, depending on the liberation of Fe containing particles (Meyer, 1980). In general, to produce a suitable pellet feed of appropriate quality, Blaine numbers of 1800–2000 cm2/g should be achieved (Van der meer, 2015)."

Jan 1, 2016

By E. Faria

"The Santa Rita mine is located in north eastern part of Bahia in Brazil and is owned and operated by Mirabela Mineração do Brasil Ltda. Typical SABC circuit was designed as the preferred option for the 4.0 mtpa (500tph) to produce a P80 of 125um for flotation. Although the SAG was originally designed to operate with conventional radial pulp lifters, later it was fitted with Outotec’s Turbo Pulp Lifters – TPL (Latchireddi, 2005). The milling circuit commenced commissioning on the 24th of October 2009 and the milling circuit achieved the nameplate capacity within days. with small and relatively simple measures to rectify. Since commissioning, the SAG mill has been working in fully autogenous grinding (FAG) mode with no balls (in contrast to the estimated 10% ball charge) and has been consistently treated up to 650tph.This paper examines the comminution design process, the operating philosophies, start-up experiences, post commissioning optimization and future development works. An evaluation of mill performance relative to the design criteria for the project life to date is also included."

Jan 1, 2012

By Garston Blackwell

Abstract - During geostatistical estimation of block grades, the kriging process produces a measure of error, the kriging variance or the kriging standard deviation. Estimation of the block error depends on the semi-variogram model for a deposit, which reflects fundamental characteristics of a deposit such as (1) nugget effect, (2) range of influence of grades, (3) different local spreads of data as a function of average grade (proportional effect), (4) nested structures, and (5) underlying anisotropies in the data; this model may be affected by sampling or assaying limitations, however. Because the kriging error incorporates so many features of both the deposit and data to be used for estimation, it may offer a substantial improvement on block classification over traditional procedures such as data density. Practice indicates that the relative kriging standard deviation (RKSD) is particularly useful for block classification in measured, indicated and inferred categories. Plots of RKSD in plan and section also can be used to demonstrate where extra drilling and sampling would be most advantageous for upgrading the class of some blocks. Moreover, the use of grade and RKSD filters can show where material near cut-off grade is poorly defined, indicating sampling target areas to improve block classification in the vicinity of the ore-waste boundary.

Jan 1, 1998

By C. H. Bertoni

"The Superior Province of the Canadian Shield is the largest gold producing area within Archean greenstone rocks in the world, with total production of over 140 million ounces of gold. One hundred and fifty-five mines have individually produced more than 8,000 ounces, although only a relatively limited number of deposits (33) produced more than one million ounces of gold. The output from these 33 deposits accounts, however, for 85% of total gold production. The majority of grades (68%) ranges between 0.10 and 0.30 ounce per ton, and there is no linear relationship between grade and tonnage.Development of new gold mines reflects the history of gold prices. However, the response to the latest increase in gold prices was not as marked. It is concluded that gold deposits are becoming increasingly more difficult to find and new exploration techniques are urgently required.IntroductionWith most of its production coming out of the Superior Province, the Canadian Shield is the largest producer of gold from Archean greenstone rock s in the world. In total gold production, the Superior Province is surpassed only by the paleo-placers of Witwatersrand and the placers of the USSR (Anhaeusser, 1976). There has been no attempt so far to compile the historical production of the Province as a whole in a single document. The aim of this work is to fill this gap, not only for the convenience of having a complete list of gold producers, but, more importantly, as a basis on which to study the tonnage and grade characteristics of these deposits."

Jan 1, 1983

By W. D. Freeborn

Slim-hole drilling and completion techniques were first used in the Cynthia area of the Pembina field, Alberta, by the Texaco Exploration Company in the summer of 1957. Prior to that time, eighty-eight wells had been drilled and completed in this area in a conventional manner. Subsequent to the initial four-well evaluation programme, twenty-one additional wells have been drilled using slim-hole techniques. No difficulty was encountered in the drilling and completion of slim-hole wells, or in obtaining production from them. A comparison of drilling and completion economics and practices has been made for slim-hole and conventionally completed wells. Penetration rates for both bit sizes (614 in. and 9 in.) were relatively equal. The shorter life of the smaller bits required the use of 15 per cent more bits per well, but the total trip time to change bits was similar for both hole sizes because of the higher hoisting speeds possible with the lighter drilling strings used in the slim holes and better hole conditions. Completion costs of the slim holes were reduced by 37 per cent as compared to the costs of conventional-type completions. This was made possible through the use of smaller well equipment, the elimination of tubing, and a reduction in rig time for completion operations.

Jan 1, 1958

ABSTRACT The inevitable uncertainty in modelling spatial variables decreases as more data become available. This reduction depends on the properties of the variable being modelled. Spatially continuous variables show less uncertainty for a given spacing than erratic variables. A geostatistical simulation based approach is developed to quantify the relationship between uncertainty and data spacing. Reference realizations are sampled to condition additional realizations and quantify uncertainty. The procedure is automated, making it straightforward to consider sensitivity and different geological domains. A case study of the relationship between uncertainty and data spacing for net oil sands thickness data from northern Alberta is presented. _ KEYWORDS Simulation, Sampling,

Jan 1, 2013

By A. K. Debnath

The water resource is key to survival of the mankind and this resource is now becoming critical in many parts of globe including India. As per an assessment of Central Ground Water Board (CGWB) of India, a huge shortfall of about 58 billion m3 of water is anticipated by the year 2050. In order to counter this shortfall, there is thrust from Government of India to adopt water conservation measures. National Environment Policy, 2006 of Government of India also stresses upon the need to take up water conservation measures for water security of the country. The coal mines in India provide an excellent opportunity to take up water conservations measures therein. The mine water is not acidic unlike western countries and it conforms to the prescribed regulatory standards. This nature?s gift is utilized in Coal India Limited by allowing mine voids to get filled with mine water. The net recharge potential of the opencast mining area is found to be about 5% in comparison to 2% in non-mining area offering good prospects for ground water recharge. The seasonal rainwater is also diverted into mine voids left at the end of mining operations which act as huge reservoirs/ pit lakes for storage of the water. They also serve as surface water bodies for recharging of water table in the surrounding areas. The area and space left from where coal has been extracted completely in underground mines and will not be entered by any man or machinery after the extraction, called goaf, are also potential source of water conservation. These additional water resources created are being utilized for meeting the industrial, domestic, irrigation and other requirements of the projects and local communities eliminating the need to tap other fresh water resources including ground water. Presently, 75% of the water demand of the coal mining project is being met from the water stored in the mine pits. In future, CIL is likely to create about 3.3 billion m3 of water resource, on an average, in its opencast mines alone. In the mine closure plan of opencast mines, the last cut is proposed to be developed into water body for recharge of ground water and creating additional water resources. A clean potential source of potable water is thus developed after mine closure. This will ensure water security of the country.

Aug 1, 2013

By E. G. Leonardon

The question of geophysical prospecting is one that is beginning to occupy a pre-eminent place in the minds of those actively concerned in the discovery and exploitation of ore deposits. This is in marked contrast to the reception accorded such ideas when the Junior author, six and a half years ago, began introducing electrical prospectii1g to the mining fraternity on this continent. Happily, the mention of geophysics no longer evokes the sceptical and pitying smiles that it did in those days. A little reflection will show that modern geophysical methods are merely a logical development from pre-existing technique. In the study of geological problems, is it not logical to use all possible physical properties of matter? The study of crystal form and cleavage, the examination of thin sections of minerals by means of polarized light or ordinary light, in fact, utilize physical properties of minerals for the benefit of the geologist. These are, of course, laboratory methods, and the extension of the study of similar properties into field work was inevitable. This began with the magnetometric surveys, used as early as 1760 in New Jersey to locate iron ores. Eighty-four years later, John Locke's work in the United States resulted in pointing out relationships between the terrestrial magnetic field and main tectonic features of the earth's crust.

Jan 1, 1928

By Andrew Bamber

A fast and objective spreadsheet-based model for the financial evaluation of innovative mining and processing strategies such as pre-concentration vs. a conventional base case is presented. The size and grade of the deposit must be chosen, from which a mining rate is selected. Expected operational data for the deposit as well as any mill testwork and results from the pre-concentration testwork are entered as input variables on the sheet, and cost and revenue impacts are calculated in the ?Output? sheet. A capital sum and operating costs for the initial mine and mill development as well as the pre-concentration facility are calculated. The net changes in capital and operating costs are calculated, and impacts on revenue through changes in metal recovery are also calculated. These outputs are used to calculate the overall impact on the cutoff grade and thus the size of the mineral reserve using a generic grade-tonnage model. The NPV and NPV profile of the two scenarios is calculated, with variations in basic parameters such as operating cost, capital requirements, metal price or grade as well as discount rate. Cost and revenue impacts are evaluated and compared to the baseline to establish a positive or negative impact overall. Different scenarios of grade, tonnage, mining rate, process performance, capital and operating cost structure can be explored using the model. Outcomes projected by the model for case studies conducted thus far have been calibrated against internal estimates by the sponsoring organizations and found to be accurate to within 30%, confirming the utility of the model in practice.

Oct 1, 2009

By Jose R. Hernandez-Aguilar

"This paper revisits data from previous studies (Hernandez-Aguilar, 2010, 2011) to better understand the link between metallurgical performance and bubble size (Db) in the collection (pulp) zone of full-scale flotation systems. To obtain conclusive evidence exclusively related to the collection zone, the experiments were designed in those studies to control both the bubble generation method and the influence of the froth zone on the overall metallurgical performance in industrial and pilot-scale flotation columns. The results showed that generating small (1 mm) bubbles had a significantly higher beneficial effect on the recovery of coarse (> 75 µm) particles compared to the effect on fine (< 16 µm) particles. It was observed that, under certain practical conditions, the recovery of liberated coarse particles was close to zero, but could be recovered almost completely by reducing bubble size. The evidence revealed an apparent inconsistency of the so-called “k–PSb” model: at constant froth recovery, increasing Sb did not always result in higher recovery, as the model predicts. Overall, the evidence showed that it was not the Sb but the bubble size that proved to be a more reliable link to metallurgical performance. Only under highly suboptimal bubble size conditions (Db = 3 mm) did the froth zone seem to play a role, possibly reflecting an effect of pulp-zone bubble size on froth stability. However, for the most part, both the bubble generation method and the froth zone played inconsequential roles. An empirical model that better describes the kinetics of particle collection is proposed.INTRODUCTIONStudies showing the link between metallurgical performance and the interactions of bubbles and particles in the collection (pulp) zone of industrial flotation systems are scarce. A common belief among a number of mineral processing practitioners considers that “small” bubbles are favourable to recover “small” particles and that, conversely, “larger” bubbles are more efficient at floating “coarse” particles. However, perceptions like this are often substantiated by anecdotal evidence rather than by rigorous data analysis. What is the optimum bubble size for a particular case, how operating conditions can be adjusted to control a target bubble size, and whether the bubble size needs to be changed in the first place to optimize the operation of a flotation plant are questions that usually remain without solid answers.The studies reported by Hernandez-Aguilar (2010, 2011) were, in part, performed to test the effect of bubble size on flotation response and, thus, help address some of the above questions. The focus of the studies was to optimize the metallurgical grade-recovery performance of the Cu-Mo separation plant at Teck’s Highland Valley Copper mine (HVC). The outcome was compelling and significantly valuable: consolidated production data showed that in 2008 – the year when the recommendations from the studies started to be implemented – the Mo plant recovery was 89%, and gradually increased to 92% and 94% in 2009 and 2010, respectively, along with an increase in Mo concentrate grade. (Note: these production figures were not included in the publications quoted above; however, they were shown during an oral presentation at the 43rd Annual Meeting of the Canadian Mineral Processors in 2011.)"

Jan 1, 2016

By Robert B. Parsons

"Effective January 1, 1990, mines in British Columbia are subject to a new provincial mining tax statute, the Mineral Tax Act. Under this Act, mines are subject to a two-tier tax system, with a minimum tax payable on ""net current proceeds"" and a higher tax paid on net income. For many mines, the present value of tax paid under the new rules should be comparable to the amount paid under the old rules. Earlier cash payments could pose difficulties, particularly for smaller mines, but existing producing mines could benefit in the short-term.IntroductionEffective January 1, 1990, British Columbia has replaced the provincial mining tax regime under the Mineral Resources Tax Act with a new system under the Mineral Tax Act. The new rules borrow some ideas from other provinces (New Brunswick&apos;s two-tier concept, and Saskatchewan&apos;s indexed costs) with a view to levying a tax that is fairer to both the producer and the province."

Jan 1, 1990

By Daniel Hodouin, Bruno Girard, Claude Bazin

"Mineral processing and smelting operations have the reputation of being complex processes. Process operators of these unit operations have acquired from experience and basic training a superficial understanding of the relationships between process output and manipulated variables. This understanding, which is a very valuable know-how for process control and optimization as well as for operator training, is however difficult to extract. This paper describes a time series based approach that can be used to extract this know-how, which can subsequently be used for operator training. The method is illustrated with an example taken from a smelting process.IntroductionThe emergence of Total Quality Management and Statistical Process Control philosophies in the North American industry (Brown, 1991 ), as well as the increasing popularity of the IS0- 900x standard accreditation, provide a strong incentive to review the training procedures for plant operators. The importance of employees training is acknowledged in two of the 14 points of Deming's road to quality (Deming, 1982) as well as by control engineering consultants (Hendricks et al., 1994). However guidelines for the operation of industrial processes are often transferred from an operator to another one with allowance for flexible interpretation of many operating rules. Such transfer is typical of complex industrial processes to which particulate processes of ore dressing and extractive metallurgy belong.Capturing the knowledge of experienced operators is often a difficult task. Cognition engineers are able to extract this knowledge and transfer it into rules that ultimately are implemented into expert systems. Cognition engineers are however not always available and plant supervisors may prefer to keep training as an internal liability. Another difficulty through interviewing of the process operator is its lack of willingness to transfer what he has learned by hard working to other people, whose ultimate goals are to develop computerized applications that may replace him in a near future, or reduce its importance in the production line.This paper shows that time series can be advantageously used to capture the average process understanding of plant operators and to help reviewing training procedures. The method s illustrated with data collected during normal operation of electric arc furnaces and it is shown how the approach has led to a fruitful discussion between process engineers and operators that ultimately provided savings of more that $200,000 per year per furnace. There are 9 furnaces in the studied foundry. Such savings are not the results of application of advanced control strategies nor of ""miracle press button software», but of an improve awareness by engineers and operators of the importance of properly defining the operating procedures to control a process."

Jan 1, 1996

By J. Ramirez-Castro, J. A. Finch

"Galena is the finest component of the product of a closed-circuit grind treating a lead-zinc ore, largely due to preferential recycling of this high-density mineral by the cyclone. For example, at the Pine Point Mines concentrator, for ~ 55% -200 mesh over-all, the galena will be close to 95% -200 mesh. This sliming of the lead can limit recovery, selectivity and dewatering. A proposed circuit modification to reduce the sliming is to incorporate a unit cell. A simulator was constructed to study the No. 3 grinding circuit at Pine Point modified by a unit cell on ball mill discharge (BMD).The simulator used a cumulative size basis rate-of-breakage with plug flow ball mill model, the parameters being obtained by laboratory grinding tests. Flotation and the cyclone models used a cumulative recovery/size matrix. The behaviour of each mineral, galena, sphalerite, pyrite and calcite/dolomite, was simulated. Simulation was adapted to a programmable calculator. A close fit to the existing circuit performance at two tonnages and mineral mixes was established.The simulator showed that the modified circuit could significantly coarsen the Pb grind, from 95% to —50% -200 mesh, depending on recovery, without substantially altering the size of the other minerals. The other principal findings were: compared to laboratory flotation tests on existing circuit BMD, the unit cell concentrate (CONC) will be coarser and markedly lower in grade; relatively low unit cell stage recoveries are desirable, because the cyclone scavenges the tail to give a circuit recovery which is higher than the unit cell stage recovery; unit cell stage recovery should not exceed the cyclone stage recovery, as the latter is the maximum circuit recovery; low unit cell stage recovery helps offset the disadvantage of the high flow at BMD; other high-density minerals will also be scavenged into the CONC, as illustrated by pyrite, making CONC quality difficult to maintain; density control of BMD flotation does not greatly alter feed density to the cyclone or ball mill.Possible plant metallurgy is forecast for a CONC diverted to final lead concentrate."

Jan 1, 1980

By S. Luidold, A. Poscher, H. Antrekowitsch

"The rare earth elements (REE) are nowadays mainly used for permanent magnets, catalysts, hydrogen storage alloys in rechargeable batteries, for glasses, ceramics, and polishing agents. Other important areas of application are phosphors in different types of lamps (fluorescent tubes, energy-saving lamps, etc.). These lamps are often collected and treated at their end of life by disintegration and sorting. However, the obtained fine fractions comprise not only REE-containing phosphors but also small amounts of mercury and are therefore disposed till today in special landfills. Due to the enormous price increase of the rare earths during the last two years, a lot of activities started for extracting these elements from secondary resources such as for example phosphors. All recycling concepts for this task mainly work with hydrometallurgical methods. The large number of different compounds in phosphors with sometimes very different behaviors with respect to their solubility in aqueous phases forms a major challenge to achieve good yields as well as acceptable purities of the produced rare earth concentrates by a process with a reasonable number of operation steps. Therefore, this paper gives at first a brief overview about the compounds, used as phosphors and about existing concepts or investigations. It further describes our own process design and the results, obtained on laboratory scale. INTRODUCTIONThe rare earth elements (REE) have a central position in the industrialised world despite their marginal production volume in comparison to common metals such as aluminium, copper, zinc etc., because they are essential for many applications. They often cannot be substituted without a considerable loss on functionality and quality. This group of metals comprise the lanthanoids (f–block elements, lanthanum–lutetium) as well as scandium and yttrium.The estimated world mine production of REE amounted to 133,000 t rare earth oxide equivalent in 2010, whereat China accounted for 130,000 t or 98 % (Cordier, 2012). The European Union (EU-27) imported 23,013 t in 2008 to cover its demand. The figure 1 shows the fraction of the European member states in terms of the total imports of rare earth compounds from outside the EU-27 (Schüler, Buchert, Liu, Dittrich, & Merz, 2011)."

Jan 1, 2012

By Shahram Tafazoli

ABSTRACT: This article presents a novel technology for sensing the size of rocks after blasting in hard rock mines. Blast engineers require rock size statistics to carefully adjust the blasting parameters. The rock fragmentation requirements vary depending on the ore type and crusher specifications. The most popular statistical parameters in the industry are the so-called P numbers (e.g., P80 and P100). A machine vision based system is introduced here for automatic image collection and fragmentation analysis of the material right inside the bucket or dipper of mining shovels. A heavy-duty camera provides the required imaging data to an embedded computer mounted inside the cab. A custom machine vision software continuously analyzes the captured bucket images and stores the suitable ones in local storage which are then fed to a Desktop software for automatic fragmentation analysis. This technology has been developed by Motion Metrics International and is commercially available as FragMetrics?.

Oct 1, 2009

By Shahram Tafazoli

This article presents a novel technology for sensing the size of rocks after blasting in hard rock mines. Blast engineers require rock size statistics to carefully adjust the blasting parameters. The rock fragmentation requirements vary depending on the ore type and crusher specifications. The most popular statistical parameters in the industry are the so-called P numbers (e.g., P80 and P100). A machine vision based system is introduced here for automatic image collection and fragmentation analysis of the material right inside the bucket or dipper of mining shovels. A heavy-duty camera provides the required imaging data to an embedded computer mounted inside the cab. A custom machine vision software continuously analyzes the captured bucket images and stores the suitable ones in local storage which are then fed to a Desktop software for automatic fragmentation analysis. This technology has been developed by Motion Metrics International and is commercially available as FragMetrics?.

Oct 1, 2009

By Shahram Tafazoli

This article presents a novel technology for sensing the size of rocks after blasting in hard rock mines. Blast engineers require rock size statistics to carefully adjust the blasting parameters. The rock fragmentation requirements vary depending on the ore type and crusher specifications. The most popular statistical parameters in the industry are the so-called P numbers (e.g., P80 and P100). A machine vision based system is introduced here for automatic image collection and fragmentation analysis of the material right inside the bucket or dipper of mining shovels. A heavy-duty camera provides the required imaging data to an embedded computer mounted inside the cab. A custom machine vision software continuously analyzes the captured bucket images and stores the suitable ones in local storage which are then fed to a Desktop software for automatic fragmentation analysis. This technology has been developed by Motion Metrics International and is commercially available as FragMetrics?.

Oct 1, 2009