Search Documents

By P. Groleau, O. Tavchandjian, D. Marcotte

In open pit mining, each small mining unit (SMU) is selected for mill processing based on an estimate of its true grade. The estimation is usually done using analyses of cuttings from blast holes within that SMU. One common estimator used for selection is the arithmetic average of within-SMU samples. This estimator is conditionally biased. The effect of a conditional bias is to overestimate the profit really recovered from the deposit. For this reason, a conditionally unbiased estimator is preferable. Increasing the number of samples generally improves the accuracy of the estimation (and diminishes the conditional bias, if present, of most estimators). However, there exists a practical limit where an additional sample does not improve the estimation sufficiently to cover the expense of making the analysis. This limit is specific to each deposit and depends on geostatistical parameters, economic factors, and mining parameters. This study examines how the number of samples affects the recovered reserves and the resulting profit. Also, the effects on optimal profit of varying the different factors are examined. Globally, the number of samples required increases with the selectivity of the operation. For a given ore deposit, the greater the number of SMUs selected for processing, the fewer samples are required and vice-versa.

Jan 1, 1998

By D. Sancho, M. Weber

"At the start of a new shaft project, a specific number of ground investigations are performed. However, it is not uncommon that the ground conditions during shaft sinking may differ from the designed ones. Therefore, it is extremely important to use tools which minimize discrepancies and to include a monitoring system in the shaft design to collect sufficient data. The paper presents an overview of existing monitoring techniques and discusses future works required to improve, not only the construction during shaft sinking, but also the lining design methodology. INTRODUCTION In most cases, the investigations performed at the start of a new shaft are based on the analysis of rock and soil probes obtained from boreholes. In practice, such analysis performed on a single core often leads to different results when conducted by various experts. The discrepancy in core analysis influences further rock mass assessment and design assumptions. It is not uncommon that the ground conditions during shaft sinking may differ from the designed ones, which affects the estimated stress and strain state of the shaft lining. Therefore, it is extremely important to use tools which minimize such discrepancy and to include into the shaft design a monitoring system to collect sufficient data, which enables control of important phenomena, not only during shaft sinking but also during the life of the shaft. Furthermore, the information collected during shaft sinking, while it is important for proper shaft lining design and updates to the shaft lining due to the local mining and geological conditions, it is also important after shaft sinking. In the whole shaft lifetime, it is not uncommon that the shaft lining is damaged and the liner needs to be renewed (Figure 1) due to various reasons. For this purpose, detailed information collected during construction can be extremely important."

Jan 1, 2019

By O. Benavente, M. C. Hernández

Selenium is obtained mainly from copper anode slimes, which is a by-product of the copper electrorefining process. Selenium is present in copper anode slimes as silver and copper selenides. Traditionally, selenium has been obtained by pyrometallurgical processes; however, hydrometallurgy has now been incorporated either full or partial to the conventional process. Some hydrometallurgical processes are been developed and used at laboratory level an industrial scale. This document describes theoretical background and results of characterization and dissolution of selenium from a decopperized anode slimes in an alkaline oxidizing system. The results have indicated that the oxidizing leaching process reaches a practically complete dissolution of selenium (up to 90 %); the undissolved portion is due to the generation of a AgCl around the particle surfaces that delays the progression of the reaction. The results indicated that 90% of selenium extraction can be obtained by dissolution under moderate conditions of pH, temperature and reagent concentration in oxidizing medium. INTRODUCTION Selenium is distributed in the earth's crust in most rocks and soils. Selenium is essential, as it has wide range of applications in the medical and food industries as well as, used in semiconductor, sensors and photochemical devices. Selenium is rarely found in the native state, 90% of selenium is obtained from copper anode slimes, which is a byproduct of the copper electrorefining process (Lu, Chang, Yang, & Xie, 2015; Xiao et al., 2017; Yang et al., 2018). In anode slimes, selenium is present as an intermetallic compound, as Ag-Cu selenides. Currently, selenium is recovered from the anode slimes via hydrometallurgical and pyrometallurgical processes (Lu et al., 2015). The traditional pyrometallurgical method recovers selenium effectively, but faces difficulty as a result of increased energy costs and strict environmental regulations associated with the process (Li, Yang, Jin, Chen, & Tong, 2017). Therefore, hydrometallurgical processes are proposed in oxidizing medium such as nitric acid, alkaline leaching with sodium nitrate, wet chlorination and pressure leaching, amongst others (Hait, Jana, & Sanyal, 2012; Kim & Wang, 2010; Xiao et al., 2017; Yang et al., 2018).

Jan 1, 2019

By Yongjie Bu, Wei Sun, Zhiyong Gao, Yuehua Hu, Hongbiao Tao, Runqing Liu, Central South University

"The flotation behavior of O-isopropyl-N-ethyl thionocarbamate (IPETC) and pH for chalcopyrite and galena was studied through pure mineral test, adsorption quantity determination, solution chemistry calculation and Materials Studio simulation. The results show that the recovery differential value of chalcopyrite and galena is about 20% when pH of the pulp 9.5 and IPETC is 7×10-4 mol/L, the flotability differences of the two minerals is significant. There is competitive adsorption between OH? and IPETC on mineral surfaces, it lead to galena flotability is lower than chalcopyrite flotability. IPETC can remove the hydration layer on mineral surface and adsorb on active sites for collector adsorption, minerals have a better hydrophobicity.INTRODUCTIONCopper and lead are two of the most widely used metals in industrial and living, their applications include building construction, various metal alloys, heat and electricity, machine manufacturing (Zhang et al., 2014). Chalcopyrite and galena are the major source of copper and lead, normally they associated with each other. With the growing use of these resources, high grade and dissemination large particle sizes minerals are less and less, the use of low grade and complex dissemination minerals have to be paid more attention (Chen, Ye, & Li, 2010; Liu, Sun, Hu, & Wang, 2009). As the special properties and complex composition of copper-lead sulfide ore, flotation separation of chalcopyrite from galena effective is a research emphasis and difficulty point in mineral processing (Bruckard, Sparrow, & Woodcock, 2011).In the separation process of chalcopyrite and galena, it is rather important to choose effective collector (Huang, Wang, & Liu, 2014). Enlarging and using the two mineral flotability will be a good basis and start in flotation (Reyes-Bozo et al., 2014). Qin et al. (2013) made a great deal of research on flotation separation of copper/lead concentrate, collector O-isopropyl-N-ethyl thionocarbamate (IPETC), butyl xanthate (BX) and ammonium dibutyl dithiophosphate (ADTP) were investigated, BX and ADTP floated both chalcopyrite and galena well, specific adsorption appeared in the surface of mineral, the problem was the collectors were not selective enough, however IPETC showed better selective."

Jan 1, 2016

By P. C. Benedict

Introduction and Summary The Northern Empire mine is a mile east of Beardmore, and 100 miles northeast of Port Arthur, district of Thunder Bay, Ontario. Production started in March, 1934, and terminated in September, 1941. During this period, the mill treated 425,866 tons of ore, from which 153,103 ounces of gold were recovered. The lowest level from which ore was mined was the 1900, but considerable drifting was performed on the 2075 level and 800 feet on the 2415, the deepest level. The following description of the geology of the mine is recorded by the senior author but is based on the observations and complementary mapping of both authors. The vein strikes about N.72°E. and has an average dip of 80°S. (Figure 1). In stoped sections, the quartz averaged about two feet wide. On the 1725 level it was drifted on continuously for more than 7,000 feet, but in the mine as a whole practically no commercial ore was found beyond points 1,400 feet west and 1,800 feet east of the shaft. Conspicuous wall-rock alteration extended throughout this section but not much beyond its limits. There was some splitting of the vein and widening of the alteration halo on the lower levels. The average general colour of the quartz changes with depth. It may be generalized, from top to bottom, as light grey to dark grey to brownish. The brownish quartz first appeared near the bottom of the ore.

Jan 1, 1947

This paper details a brief history of the Australian gold industry from the 1980s gold boom to the present day, highlighting an industry characterised by innovation in plant design and junior companies prepared to "have a go", in contrast to the conservatism of many larger mining companies. Design flexibility, the innovation of new processes, the preparedness to exchange "process know how" and technology singularly differentiated the gold industry from other sectors during the 1980s to the present. The introduction of two stage crushing, semi autogenous (SAG) milling, and pebble crushing, mill innovations, carbon in pulp (CIP) and carbon in leach (CIL) and the North Kalgoorlie screen etc were all exciting changes in the industry.

Jan 1, 2011

By H. Henao, F. Canales

The present work evaluated the use of copper ore flotation tails as flux in the process of smelting copper concentrates. For this purpose, experimental and simulated liquidus lines were obtained at different ratios of tail/flux. Experimental variables included temperature, partial pressure of oxygen and sulfur dioxide and the conditions of tridymite or spinel saturation. The results indicate the feasibility of replacing the flux by increasing the temperature of the smelting process by 20°C. Results of simulation using FactSage and HSC confirm that the required increase in temperature can be achieved by increasing the flow of concentrate, enrichment of oxygen or increasing the matte grade. INTRODUCTION In the pyro-metallurgical process of copper production, the smelting stage produces two liquid phases, a sulphide phase rich in copper and another composed mainly of oxides called slag. The slag phase is the product of oxidation of the iron contained in the flotation concentrate. The smelting process which is carried out at temperatures of 1250°C, require the addition of silica as a flux and the injection of air enriched in oxygen (Schlesinger 2011). Currently, one of the most important aspects of the mining industry is the minimization of costs, the optimization of the use of available resources and the reduction of environmental impact. Under this context, the use of flotation tails from as a flux in the copper smelting process has the potential of reduced production costs and generate an environmental benefit by reduce the disposal amount of this waste material Regarding the use of copper tails as flux in the copper smelting process, a thermodynamic simulation study using the FactSage software had been reported in the literature (Parra et al., 2011). The results indicated an increase of 35°C in the temperature the liquidus for the equilibrium matte/spinel and a subsequent requirement of energy in the process of approximately 350 [MJ/ton slag]. Given that the calculated viscosity remains in the same order of magnitude, the melting temperature is a more relevant parameter for the evaluation of the use of tailings as flux.

Jan 1, 2019

By K. Yamaguchi

To contribute highly efficient and environmentally conscious copper smelting process, several topics in chemistry of the continuous converting were discussed. Through the reviewing the authors' thermodynamic simulations, it is recognized that small amount and low copper content of the coexisting slag is preferable. Some discussions were added to the Takeda's diagram for Cu20-FeOx-CaO ferrite slag, and the activity curves of the constituents were derived. Thermodynamic calculations were carried out on the copper contents of the slag during the blister copper formation. The dissolution of copper in slag decrease somewhat with increasing temperature, but the effects of increasing S02 pressure and decreasing %S in copper are considerable to increase in copper content of the slag. The optimum oxygen enrichment in the supplied air, and regulation of the oxidation degree for the blister copper are important in practice. The gypsum phase separation in the calcium ferrite slag was also evaluated thermodynamically, and concluded that decreasing temperature, increasing CaO content or S02 pressure, and extensive oxidation of the blister copper tend to separate CaS04.

Jan 1, 2007

By K. Yamaguchi

To contribute highly efficient and environmentally conscious copper smelting process, several topics in chemistry of the continuous converting were discussed. Through the reviewing the authors' thermodynamic simulations, it is recognized that small amount and low copper content of the coexisting slag is preferable. Some discussions were added to the Takeda's diagram for Cu20-Fe0x-Ca0 ferrite slag, and the activity curves of the constituents were derived. Thermodynamic calculations were carried out on the copper contents of the slag during the blister copper formation. The dissolution of copper in slag decrease somewhat with increasing temperature, but the effects of increasing S02 pressure and decreasing %S in copper are considerable to increase in copper content of the slag. The optimum oxygen enrichment in the supplied air, and regulation of the oxidation degree for the blister copper are important in practice. The gypsum phase separation in the calcium ferrite slag was also evaluated thermodynamically, and concluded that decreasing temperature, increasing CaO content or S02 pressure, and extensive oxidation of the blister copper tend to separate CaS04. 0

Jan 1, 2007

By Francis Wm. Gray

The preparation of a paper read before this Society in 1927 on Undersea Mining led to representations to the Deputy Minister of Mines at Ottawa, Dr. Chas. Camsell, and to the Director of the Geological Survey and the Director of the Mines Branch, which resulted in the undertaking by these bodies of a geological, physical, and chemical survey of the Sydney coalfield, combined with revision of the geological maps, on all of which much progress has been made. Preliminary studies revealed the necessity for a new base-map on a scale that would permit the representation of the whole coalfield from cape Dauphin to Mira bay on one sheet, and in the making of this map the Geodetic and Topographical Surveys have collaborated, with the assistance of airplane surveys for filling-in of detail. The new map will show all the data accumulated by 50 years of active mining and will show also the extent of mine workings, with level-contours under the sea. Dr. W. A. Bell, of the Geological Survey, has, over a number of seasons, studied in the field the historical geology with the purpose of elucidating the sequence of earth movements that have determined the structure of the coalfields, especially those that have governed the course and extent of the complementary folds that traverse the Sydney coalfield. Dr. B. R. MacKay, of the Survey, and the officers of the Fuel Testing Laboratories at Ottawa have made exhaustive studies of the Phalen seam, chemical and microscopic, intended to elucidate the conditions under which this seam was deposited, and some very interesting conclusions have been reached.

Jan 1, 1934

The writer presents a concise summary of eleven recent discoveries made in the Maritime Appalachian area, with suggestions for fur the research. This information may prove helpful to geologists working in other fields and to students contemplating further avenues of research in mining geology and exploration. INTRODUCTION THIS paper is not intended as a research study on the subject, but i. merely a brief review of eleven discoveries that have been made in the Canadian Appalachian area. Furthermore, this is not a critical analysis of the merits of any one geophysical method, but it is an un-prejudiced observation of how these discoveries were actually made and what techniques were apparently most fruitful. Some generalizations are attempted whicl1 may suggest further avenues of research in the field of mining exploration. The writer wishes to thank his colleagues in the field for their comments, which he was able to in-corporate into this paper. In particular, he is grateful to Dr. Paul Bevan and

Jan 1, 1963

By Yan Yang

The Jinfeng gold mine is one of the three gold mines that Eldorado Gold has in China and it is the second largest gold mine in China. The mine is located in a relatively remote and mountainous area in the southwestern Guizhou province. The orebody is similar to the Carlin type deposit in Nevada. The mill throughput was designed to treat 3,600 tones per day. The ore comes from open pit mining and underground mining, and is fed to one-stage jaw crushing. The crushed ore is stockpiled, reclaimed and then fed to the SABC grinding circuit. After classification with hydrocylones, the ore is floated, and the resultant concentrate is oxidized biologically in a process known as BIOX®. The oxidized concentrate is then washed in a CCD circuit and finally leached with cyanide in a CIL circuit for gold extraction. Jinfeng produces about 180,000 oz of gold per year. This paper introduces operations and modifications of SABC circuit over the past three years, and then describes some technical characteristic of the SAG mill and other circuits in the processing plant. Major modifications and improvements on the SABC circuit are described in the paper, including: 1. Impacts of grinding ball and mill liner with respect to material selection, quality, hardness, manufacturing methods, and interactions between mill liner and grinding ball. 2. Effect of milling operation parameters on milling efficiency. 3. Impacts of SAG mill scats and modifications of grate size to improve mill throughput. 4. Design and construction of a pebble crushing system, and recycle the crushed scats to the SAG mill to improve mill throughput. With the above-mentioned modifications, 20% increase over the design in mill throughput has been realized over the past three years, and operating cost has been significantly reduced. However, some issues still remain, and thus process modifications and technical innovations are still needed.

Jan 1, 2012

By R. A. Parra, Fuentes, C. Godoy, L. E. Arias, C. A. Toro, M. Marin, E. Balladares, V. Parra, G. Reyes, S. N. Torres, D. Sbarbaro

In this paper, we report on the detection of spectral molecular emission of iron oxide (FeO) and copper oxide (CuxO) emitted by reactions occurring in a laboratory scale flash smelting process of pyrite (FeS2) as well as copper concentrate. The novelty of the technique is that, the molecular spectral emission sensing is achieved by using a low spectral resolution and low sensitive radiometer, enhanced with signal processing and matrix factorization techniques. The method was validated using a highly sensitive spectrometer, with a high spectral resolution; achieving a similar FeO spectral pattern as the one obtained after signal processing techniques over low resolution spectral signals. INTRODUCTION Visible-near infrared (VIS-NIR) spectroscopy is an optical contactless sensing technique commonly used to capture information about the emitted, absorbed, transmitted or scattered radiation in a physical or chemical process, with the presence or absence of an excitation light source such as a laser or a broad spectral band source. These techniques coupled with signal processing and machine learning algorithms, sometimes referred as chemometrics (Pisapia et al., 2018), can be found in processes such as: pharmaceutical (Kandpal et al., 2016); food (Coelho et al., 2016); combustion (Ballester & García-Armingol, 2010); siderurgy (Strakowski et al., 2014) industry, among others. In the extractive copper industry there are several technological developments using optical sensing techniques aimed to retrieve information about copper ore and concentrate mineralogical composition such as X-Ray Fluorescence, Qemscan® (Quantitative Evaluation of Minerals by Scanning Electron Microscopy) and X Ray Diffraction (XRD) analysis, however, because of the manual procedures to analyze the samples with these laboratory instrumentation, only discrete information during a daily based operation can be retrieved, making impossible for the operators to take decisions over the involved processes in real time. The aim of our research work presented here is to contribute with sensing and data analysis procedures based on VIS-NIR spectroscopy for the flash smelting process characterization, particularly in this paper, with the detection of FeO and CuxO molecular emissions in a laboratory scale setup.

Jan 1, 2019

By D. D. Downing

This paper is a review of material selection considerations concerning protective coatings in the mining industry. The discussion will cover both capital-dollar projects and maintenance requirements. Emphasis will be on industrial finishes for structural steel and process equipment subjected to aggressive atmospheres. The presentation will cover the total needs of a job, emphasizing not only the owner's requirement for a cost-effective system during plant operations, but also taking into consideration the short-term requirements of general contractors, steel fabricators, erection firms and paint contractors.

Jan 1, 1979

By R. L. Bruening, J. B. Dale, N. E. Izatt, S. R. Izatt

IBC Advanced Technologies' Molecular Recognition Technology (MRT) SuperLig® products selectively and rapidly bind with target metal ions to remove them from solution. The MRT process can produce a high purity separation product of maximum added value at low cost. This paper discusses applications for MRT in the gold industry, including recovery of gold and silver as well as metal contaminants from various process and recycle streams.

Jan 1, 2011

Microseismic (MS) methods offer one of the few ways to monitor a 3D volume of rock and essentially see into the rockmass and the regions of real time rock fracture. This is a critical component when considering workplace safety as well as the economic viability of a mining operation. New Gold Inc. New Afton Mine, an intermediate copper-gold mining company located 350km northeast of Vancouver in the south-central interior of British Columbia, Canada, has recently installed a MS system to help understand the block caving process in space and time. For a block cave mining operation is it important to utilize the MS events to map out the seismogenic zone related to the regions of stress concentration and fracturing mechanisms which lead to caving. The geological setting within the local array is complex, consisting of several distinct lithologies with unique material properties that each affect the microseismic signal differently. The block cave consists of a muck filled void, also affecting the seismic waveform path. This paper compares the use of a single velocity model to a variable velocity model which accounts for the differing lithologies and cave. The variable velocity method determined 3D raypaths for all source to receiver possibilities through five irregular shaped geological domains and the estimated cave. For calibration blast data, the variable velocity model is found to successfully decrease the error for event location from an average of 38m to 20m (47% improvement), and its importance to location accuracy is expected to increase as the cave develops in size.

Aug 1, 2013

By J. McCreedy

This paper reviews new methods of exploration for metals and new techniques of mining the deposits and extracting the metals from their ores. Examples of mining innovations are taken from Inco's Thompson Operation. The importance of presenting a favorable image of the industry to college students and young people deciding on a career is stressed.

Jan 1, 1971

By Alex Matheson, Nick W. D. Massey, Peter T. Bobrowsky

Crowing pressures on aggregate resources include diminishing reserves, high transportation costs, sterilization and land use conflicts. In the absence of detailed resource knowledge for a particular region, aggregate resource potential maps provide the best "first approximation" regarding the surficial distribution of sand and gravel. The 1:50 000 scale Level Ill aggregate potential map integrates several important factors which influence the management of sand and gravel. Data used to generate this type of thematic map is readily available in most areas, fieldwork required is minimal, there is a logical quantitative evaluation of the data layers and integration is easily accomplished on a desktop PC-based platform. Also the aggregate potential map, with its focus on identifying areas of potential future aggregate exploitation as well as present inventory, provides a useful tool for the aggregate explorationist.

Jan 1, 2001

By Harold J. Rose

"A VETERAN newspaperman once summed up a lifetime of observation and experience in these words:""What man can imagine, man can do"".That statement might well serve as the theme of a talk on research potentials of the coal industry or any other industry. It is not my intention today to make a series of predictions of things to come. Experience of the past few decades has shown that long-range predictions made be-fore engineering groups usually fall short of the mark; that is, the actual technical achievements in any period tend to surpass the boldest predictions that any responsible engineer would have made, say twenty years earlier.Instead, I will point out some recent accomplishments or refer to research that is in progress or now being planned in order to suggest important trends to be expected in the next few years. Based on this rapidly increasing tempo of achievements you can make your own extrapolations into the future."

Jan 1, 1959

By Kurt Tischler

This paper presents the field experience of Siemens with regard to Gearless Drives in the mining industry ? We consider the elapsed production hours of Siemens Gearless Drives to be extensive enough to provide a reliable estimation of availability calculated on the basis of data representing repair time, downtime, and operating time. The users of Siemens Gearless Drives confirm an availability of more than 98% after exclusion of some major issues. The paper addresses all of these major issues of Siemens Gearless Drives, describes successfully applied corrective measures, explains the influences on the design of the drives, and lists the downtimes associated with each of these issues.

Jan 1, 2012