Search Documents

By G. W. R. Kuzyk

"Hydraulic drills, recently implemented at the Tantalum Mining Corporation of Canada, Limited, Bernie Lake Mine, are proving to be an economic alternative to pneumatic drilling systems. The paper describes the application of an electric-hydraulic drill jumbo to the mechanized room-and-pillar mine and its performance. The application of these drills resulted in improved environmental and working conditions.Drill rods and bits are a major cost centre in hard-rock mining applications. The paper also discusses the performance of one manufacturer's product used on the hydraulic drills.IntroductionThe Tantalum Mining Corporation of Canada, Limited (TANCO) started producing tantalum ore from its Bernie Lake pegmatite in 1969. The pegmatite, encased in amphibolite, is shallow seated and flat lying. It is defined by diamond drilling along 4,000 feet of strike and 1,500 feet down dip, ranging in thickness from 60 to 280 feet. Relatively well defined zones of mineralization occur within the pegmatite and form separate orebodies of tantalum, lithium and cesium."

Jan 1, 1981

By P. H. Shipway, D. G. McCartney, H. Saghafifar

The microstructural changes during thermal ageing at 650ºC in the interfacial region of Alloy 625 weld overlay on a 2.25Cr-1Mo steel was evaluated. Optical microscopy, scanning electron microscopy in SE and BSE modes, electron probe microanalysis and hardness mapping were used to characterize as-welded microstructure and its changes during thermal ageing and precipitates of interfacial region. Carbon migration across the interface was recognised as a major issue. A region of 300 µm wide adjacent to the fusion line, which was found harder in the as-welded condition decarburized during thermal exposure. Studies revealed that this region transformed to a soft region containing large ferrite grains and micron-sized carbides. In the weld overlay, a 50 µm wide hard band (over 650 Kgf mm-2) adjacent to the fusion line formed and carbide precipitates were observed along grain boundaries. Carbide precipitation mostly occured in the 150 µm wide region close to fusion line.

Jan 1, 2017

By K. Waters, A. Navarra, T. Grammatikopoulos

Strategic decisions to develop a mineral deposit are subject to geological uncertainty, due to the sparsity of drill core samples. The selection of metallurgical equipment is especially critical, since it restricts the processing options that are available to different ore blocks, even as the nature of the deposit is still highly uncertain. Current approaches for long-term mine planning are successful at addressing geological uncertainty, but do not adequately represent alternate modes of operation for the mineral processing plant, nor do they provide sufficient guidance for developing processing options. Nonetheless, recent developments in stochastic optimization and computer data structures have resulted in a framework that can integrate operational modes into strategic mine planning algorithms. A logical next step is to incorporate geometallurgical models that relate mineralogical features to plant performance, as described in this paper.

Jan 1, 2017

By Earl Gebhardt

"The planning and design of mining panels in the Potash Corporation of Saskatchewan Inc., Lanigan Division mine Block B involved a number of investigative techniques. The techniques utilized to gain insight into the viability of mining included2-D and 3-D seismic surveys, longhole drilling, exploration wells, photo lineament, magnetic and gravity surveys, and actual room excavation.IntroductionPotash Corporation of Saskatchewan Inc. (PCS) owns and operates four potash mines in the province of Saskatchewan. The Lanigan Division mine is located 110 Ian east of Saskatoon, Saskatchewan, near the town of Lanigan.The Lanigan Mine commenced production in August 1968under the ownership or Alwinsal Potash of Canada Limited. The mine was purchased by PCS in 1977.Lanigan Division's productive capacity is 3.4 million tonnes of product per year. Ore is extracted from the "" B"" zone or Layer III or the Patience Lake member of the Prairie Evaporite, more than 1000m below surface . The Patience Lake member (approximately 20 m thick) consists of potash interbedded with salt. The average run-of-mine ore grade is 21070 K20 (Fig. I).The mine was initially developed using the room-and-pillar technique. Improvements in mining resulted in the use or extensible conveyors in long panel rooms."

Jan 1, 1993

By Richard J. Kolada, Ian R. Muirhead

"This paper reports on a CANMET-funded examination of less conventional underground coal mining methods. These methods are documented and those that show the most promise for application to western Canadian conditions are discussed in detail.IntroductionIn recent years, mining considerations and economics have encouraged a transition from underground mining to surface mining. However, a change in market conditions or the development of superior underground mining methods may reverse this trend . Should this happen, the industry must be quick to respond and have information available on the latest developments of underground mining technology. In time, deposits of high-quality coal, which are easily accessible to surface mining, will be depleted and a change to underground mining methods will require consideration. The economic transition point between surface to underground will be a major determinant in maintaining a competitive edge. For these reasons, it is important to keep abreast of improvements in underground mining methods. To meet this objective, CANMET awarded a research contract to Monenco Consultants Limited, to investigate unconventional underground mining methods that show a potential for western Canadaoi. This paper presents the results of this investigation."

Jan 1, 1988

By V. V. Zubkov

The systems of geophysical monitoring have been already put into operation at coal mines and ore mines. Since at present it is rather difficult to conduct mine experiments; it is necessary to start a new step in joining of geomechanics and seismic. The linking geomechanical and geophysical monitoring at coal mines and ore mines today became possible due to progress in development of numerical methods of modeling of stress state and technology for processing of seismic information. This paper describes one potential step in linking geomechanical and seismic monitoring at coal mines and ore mines.

Aug 1, 2013

By D. A. Peterson, R. Pakalnis, G. Peter Mah

"Laboratory and trial installations have been completed to determine the potential of composite cable bolt reinforcement in Canadian underground mines. Several prototypes of glass fibre cable bolts have been developed and tested, two of which are currently available to the mining industry. Their evalualtion consisted of lab testing in Canada and the United States, along with trial installations in several underground mines throughout Canada. The objective was to develop a cost competitive composite cable bolt equivalent in strength to that of a 16 mm (Ys in.) diameter steel cable bolt. In addition to achieving equal or superior load carrying characteristics in tension, the glass fibre cables generally experienced an increase in the rate of installation due to their lighter weight. Unlike conventional steel cables, composite cables may be installed within mines which utilize continuous excavation and which require cuttable support. A market analysis of cable bolt usage in Canada has been completed. Glass fibre cable bolts are an effective means of rock reinforcement in mining applications. They prove to be a viable alternative to conventional steel cable bolting. IntroductionCurrent cable bolting practice consists of cement grouting one or more steel cables within a drill hole in order to support the surrounding rock mass. Cable bolts are a form of internal support and are generally used as pre-support in open stope and cut-and fill mining methods. They can be either tensioned (active support) or untensioned (passive support) and may be of any length, though for underground mining applications, are generally less than 20 m (65.6 ft) and are untensioned. A major advantage of cable bolts is that they are flexible and can be coiled to approximately 1 m (3.3 ft) diameter coils. This allows relatively long lengths (>20 m, [65.6 ft]) to be installed in areas with limited head room (1.8 m)."

Jan 1, 1994

By L. Voisin, E. Díaz, V. Montenegro, W. Kracht

Grinding media is of great concern in the mining industry mainly because its consumption represents an important part of the costs during mineral processing and consequently, of the total mining business OPEX. In addition, grinding media consumption impacts directly on flotation performance through negative contamination by corrosion, affecting the pulp chemical potential, complicating the understanding and control of the process, as galvanic interactions between mineral species also occur. In addition, during the process there is also a physical consumption of the grinding media through erosion and impact. In both cases, mineralogy has an important role because pulp abrasion power, chemical reactivity, rheology, hardness and other variables depend on the minerals contained in the pulp and their interactions. In the present study, a geometallurgical and phenomenological model, which describes the grinding media consumption and its relationship with mineral hardness expressed by Bond Work Index, was obtained based on advanced mineral characterization techniques such as Hylogger3TM, X-ray diffraction, X-ray fluorescence and experimental grinding tests using a laboratory mill applied on Chilean copper pulps. The results obtained show that pH has an important effect on grinding media consumption, because corrosion varies with hydrogen ions availability. Also, mineral hardness depends on mineralogical composition, but textural analysis must be performed to have a better description of this property. Finally, minerals present in a sample define the grinding media consumption mechanism, because a sample with harder minerals and a greater value of Bond Work index is capable of protecting grinding media from impact wear, while a sample with lower hardness but with a big sulfide minerals content would be more aggressive with grinding media because corrosion is more important in this case. The geometallurgical model obtained is capable to relate the grinding time, mineral hardness, content of sulfide minerals and grinding pH to estimate the grinding media consumption.

Jan 1, 2017

"RésuméDans la première partie de cet article on discute Ie mode d'écail age aetueJJement en usage dans des mines souterraines. Par la suite, on presente la problematique d'écaillage à l’aide de barres conventionnelles et on discute les plus recénts développements des outils d'ecaillage portatifs et mécanisés ainsi que les techniques de détection des roches branlantes. Plus tard, on analyse la tâche d'écaillage avec des barres conventionnelles. Dans les chapitres qui suivent on présente un concept d'un outil d'écaillage portatif et mécanisé développe à l'Université Laval, ainsi que les résultats des essais de cet outil, effectués dans quelques mines au Québec. On constate que Ie nouvel outil d'écaillage démontre un potentieJ intéressant tant au niveau de l'effort requis pour effectuer la tâche d'écaillage que de la sécurité des mineurs.On conclut que l’application de cet outil fera un pas important sur Ia voie d'amélioration des conditions de travail dans les exploitations souterraines, tout en assuarnt une qualité accrue de l'écaillage.AbstractThe first part of this paper discusses the type of scaling operations presently in use in underground mines and derma; a scaling factor which is expressed as the:: area necessary to scale to extract one ton of ore. Subsequently, the problems associated with conventional scaling methods are discussed as well as recent developments in mechanized hand-held scaling devices and methods of loose detection. The elements of the scaling process are further analyzed. In subsequent sections of this paper, the conception and design of a mechanized scaling device, developed at Universite Laval is described. The results of field tests conducted in Quebec hard rock mines are presented. The experimental findings show that the mechanized hand-held scaling device shows great potential in improving the productivity and safety of underground mining operations."

Jan 1, 1995

By S. Castro

Hydrolysis of metallic ions depends on pH and the products of hydrolysis either activate flotation or can lead to inadvertent activation of gangue particles, but can also depress flotation of valuable components. One of the most recently studied topics is the use of seawater in flotation. Seawater is a concentrated NaCl solution (about 0.6 mol/L) that also contains considerable amount of Mg2+ and Ca2+ ions. The hydrolysis products of Mg2+ strongly depress flotation of molybdenite over the pH ranges over which they form in the process water. This effect can be eliminated by removal of hydrolysing ions from the process water or by carrying out the flotation at the pH over which such a hydrolysis can be avoided. The former can be exemplified by prior precipitation of the harmful hydrolysing ions as, for example, in the University of Concepcion Patent. The latter can be exemplified by the use of metabisulfite to depress pyrite in the flotation of Cu-Mo sulfide ores in seawater, the process that is carried out at much lower pH, which avoids formation of Mg2+ hydrolysis products.

Jan 1, 2017

By T. Newton, G. A. Bezuidenhout, P. J. Tauetsile, F. Trask

The technology to selectively leach gold, silver and base metals from ores, concentrates, and wastes, using an alkaline glycine solution, has initiated significant interest in using the new technology in various environments such as in-situ, in-place, dump, heap, and vat and agitated tank leaching. It has been shown that glycine acts synergistically with a number of other lixiviants to lower the net consumption of the other lixiviants while allowing low cost glycine solution recovery. Glycine is a non-toxic, stable, environmentally benign reagent that is available in bulk industrial quantities. It has the ability to dissolve most copper oxide and sulfide minerals, as well as native copper, whilst not interacting with acid consuming gangue nor dissolving iron and various or ubiquitous gangue elements. It acts synergistically with small amounts of cyanide to leach gold-copper ores at leach rates higher than either glycine or cyanide on their own, while significantly reducing cyanide consumption and eliminating detoxification requirements. The leaching behaviour of various glycine based systems will be reviewed, followed by the evaluation of the adsorption of gold onto activated carbon. Where the economics merit it, copper can be easily recovered using solvent extraction or sulfide precipitation.

Jan 1, 2017

By Derek E. McBride

"Exploration work in the Beardmore - Tashota area has led to a reinterpretation of relationships between gold mineralization and the geologicalevolution ofthe area. The host volcanic rocks form two parallel volcanic belts connected by a much smaller cross-cutting band, which trends northeast from Beardmore to Tashota. This connecting band consists of mafic and felsic volcanic, plus clastic sedimentary rocks in a sequence conformable with the contact of the Onaman Lake Batholith to the east. A metamorphic aureole or incorporated xenoliths are lacking along this major contact and the only intrusive relationship observed is chilling between mafic dikes and a cold host granite in proximity to it. Granite dikes are totally lacking in the volcanic succession, or the overlying sedimentary sequence. A major part of this sequence consists of a polymict basal conglomerate with granite boulders and volcanic clasts in a fine-grained chloritic matrix. The nearest source for these boulders is the Onaman Lake batholith.Gold mineralization in significant economic quantities (+ 50 000 ounces) occurs at the top or above the mafic volcanic succession as quartz bands. In the Northern Empire Mine, the band is conformable, folded, boudinaged and the mineral zoning shows a relationship to variations in the host rock, not structural overprinting. In general, where the host mafic tuff is medium-grained, the quartz band is thicker, up to a metre wide, and carries economic grade; where the tuff is finer-grained and bedded, the band is very thin and low grade.Stratigraphic control and metal zoning shows that the mineralization formed as part of the development of the volcano- sedimentary succession. The other major deposits in the area (Leitch and Sturgeon River) have a similar structural history suggesting that they are also syngenetic in terms of the stratigraphic development. Regionally, these deposits were emplaced prior to any significant tectonic deformation but at the end of the mafic volcanic event.The mafic activity was related 10 a period ofextension which caused the volcanic troughs to develop along centres of rifting. The hiatus at the end of this event permitted extensive hydrothermal systems to form and deposit siliceous exhalite bands within sedimentary or terminal mafic volcanic environments in promixity to major thermal sources. Subsequently, the Kenoran Orogeny deformed the entire succession into upright folds with a sub-vertical schistosity. Evidence shows that the deposits have remained intact since deposition."

Jan 1, 1987

By Stephen Hardcastle

Presentation Outline ? Introduction ? Mine Ventilation Facts ? Ventilation-on-demand (VOD) ? Sensors/Controls ? Continuing Work ? Conclusions ? Mine ventilation engineering practices were published in 1556 in Agricola?s De Re Metallica (wind sails, bellows, etc.) That was then? This is today? Large fan installations handling >1M cfm

Nov 1, 2011

By Arnold R. Pasieka, George V. Sotirow

"The object of this paper is to outline a computerized net cash flow approach for practical cutoff grade determinations. A cutoff grade carries not only geological but also economic value, in which costs are balanced against revenues. For different situations, cutoff grades are a 'standard of value' that are determined for the purpose of classifying economic or uneconomic mineral reserves in a specified time frame. In a constantly changing technical and economic environment, the decision to develop or maintain a mining operation at its best economic potential, requires an appropriate cutoff grade strategy, a strategy consistent with short- and long-term operational and corporate objectives and one based on realistic marketing and metal prices forecasts. The use of a project evaluation computer program, in combination with specific corporate net cash flow requirements, shows the most promising and flexible team approach for cutoff grade optimization.IntroductionThe recent recession has had a devastating effect on the Canadian mining industry. Exploration and mining R&D expenditures have been critically reduced and now are believed to be below healthy levels. Ore reserves, mine life and cutoff grades are careening in several directions because of low base metal prices, relatively high costs and sensitive precious metal prices.These conditions demand an improved understanding of the terms ""ore"" and ""cutoff grades"" as they are applied to the planning process and day-to-day operations. ""Ore"" or 'ore reserves"" is a dynamic concept, reflecting a cumulative effect of changes in geological, technical and economic conditions in terms of material which can be mined at a potential profit. By contrast, if economics are not the primary consideration, the term ""mineral reserve"" or ""mineral inventory"" should be used to describe the mineral deposit. For different situations, cutoff grade is ""a standard of value"" determined for the purpose of classifying mineral reserves as economic or uneconomic in a specified time frame. The question of mining at average reserve grade or low-grade material during high metal prices is of paramount importance for cutoff grade strategy."

Jan 1, 1985

By Tibor Horvath

Dust abatement is possible on bulk materials, whether conveyed or stockpiled. Minimum (ppm) quantities of chemical additives can efficiently and rapidly control dust of conveyed substrates with no effect on floatation chemistry. Top coating of large surface areas can control surface dust and wind erosion. Environmental and toxicity impact must be considered in any treatment, especially on areas with percolation runoff, leachates, or limited containment. The most effective dust control is preventing release of substrate fines rather than trapping and removing air borne dust. Techniques to prevent release of fines from conveyed substrates will be discussed. Dust control dynamics are a very complex combination of solid phase physical and chemical interactions between the substrate and the fines. ?Smart Technology? products permit dust abatement of stockpiled substrates and tailing fields with no environmental impact. Using ?Smart Technology?, the dust abatement products remain active and can re-seal damaged areas. Efficient, low environmental and toxicity impact, dust control will be demonstrated through case studies where these principals have been applied.

Oct 1, 2010

By J. E. Nesset

"This paper discusses the importance of considering residence time distribution (RTD) in the design of flotation and mixing circuits and in the analysis of operating problems. The experiences and successes of Brunswick Mining in this area are covered and include: the development of a practical RTD measurement technique using pulp conductivity, baffle installation to improve the RTD of existing process equipment, and the method in which RTD considerations have been used to design the newest flotation and conditioning operations IntroductionThe use of residence time distributions (RTDs) in the design and analysis of unit operations is well understood by the chemical engineering profession in while mineral processing engineers have tended to rely on empirical and rule-of-thumb factors. For example, in scale up from laboratory and pilot test results to full size flotation plant design, empirical rule s are often used to establish residence time and number of cells in the bank. Coleman suggests a factor of at least 2, and up to 5 for gold ores, be applied to laboratory determined flotation times. This is further illustrated in Table I, taken from Denver equipment. The number of cells in series to achieve the required retention time while minimizing short-circuiting has generated a variety of conclusions (Table 2). Obviously there is less than complete agreement on the subject. Young notes that a clear difference of opinion has emerged and cites as extremes, (i) the publications of Outokumpum showing unimpaired recovery for its largest machines (38 m3) compared to equivalent retention times for numerous smaller machines, and (ii) the experiences of Eastern European countries where the practice is to install banks of 30 unit s or more, operating in series, often with unit retention times of only a fraction of a minute.The empirical factors used by engineers presumably account for other than tested feed conditions, inefficiencies in large continuous machines, inevitable day-to-day circuit disruptions, gradual equipment deterioration and any other safety factor the engineer feels compelled to incorporate. An understanding of RTD concepts and techniques should help the practicing mineral engineer to develop more soundly based factors. Thi s paper relates the experiences of Brunswick Mining in using RTD techniques in the unit operations of flot ation and mixing"

Jan 1, 1988

By J. E. Nesset

"This paper discusses the importance of considering residence time distribution (RTD) in the design of flotation and mixing circuits and in the analysis of operating problems. The experiences and successes of Brunswick Mining in this area are covered and include: the development of a practical RTD measurement technique using pulp conductivity, baffle installation to improve the RTD of existing process equipment, and the method in which RTD considerations have been used to design the newest flotation and conditioning operations. IntroductionThe use of residence time distributions (RTDs) in the design and analysis of unit operations is well understood by the chemical engineering profession in while mineral processing engineers have tended to rely on empirical and rule-of-thumb factors. For example, in scale up from laboratory and pilot test results to full size flotation plant design, empirical rule s are often used to establish residence time and number of cells in the bank. Coleman suggests a factor of at least 2, and up to 5 for gold ores, be applied to laboratory determined flotation times. This is further illustrated in Table I, taken from Denver equipment.The number of cells in series to achieve the required retention time while minimizing short-circuiting has generated a variety of conclusions (Table 2). Obviously there is less than complete agreement on the subject. Young notes that a clear difference of opinion has emerged and cites as extremes, (i) the publications of Outokumpum showing unimpaired recovery for its largest machines (38 m3) compared to equivalent retention times for numerous smaller machines, and (ii) the experiences of Eastern European countries where the practice is to install banks of 30 unit s or more, operating in series, often with unit retention times of only a fraction of a minute.The empirical factors used by engineers presumably account for other than tested feed conditions, inefficiencies in large continuous machines, inevitable day-to-day circuit disruptions, gradual equipment deterioration and any other safety factor the engineer feels compelled to incorporate. An understanding of RTD concepts and techniques should help the practicing mineral engineer to develop more soundly based factors. This paper relates the experiences of Brunswick Mining in using RTD techniques in the unit operations of flotation and mixing."

Jan 1, 1988

By Robert B. Parsons

"The Whitehorse Mining Initiative (WMI) brought together all of the key stakeholders in Canada's mining industry to develop a framework whereby the industry can meet the challenges that it faces into the 21st century. The WMI Accord7 which was signed at the annual Mines Ministers Conference in Victoria, British Columbia, on September 137 1994, touches all of the important issues that confront the industry, including taxation. IntroductionSeptember 13, 1994, was a historical day for Canada's mining industry. On that day, on the occasion of the annual Mines Ministers Conference in Victoria, British Columbia, the Whitehorse Mining Initiative (WMI) Accord was signed by the leaders of the five principal stakeholders in the industry: industry; government; labour; environmentalists; and aboriginals. The Accord is the culmination of two years of hard work and intense collaboration by these stakeholders. But, the Accord is not the end result. The Accord can better be described as a springboard to a prosperous future for mining in Canada.The WMI had its beginnings at the Mines Ministers Conference in Whitehorse, Yukon, in September 1992 (hence, the name of the initiative). At that time, the mining industry was well aware of the serious challenges facing the industry, including significantly increased competition for mineral investment from other mining countries, coupled with an atmosphere of uncertainty surrounding land access, environmental regulations, and taxation. The diversion of investment abroad was hurting, and would continue to hurt, all Canadians. Something had to be done. At the 1992"

Jan 1, 1994

By S. P. Jekielek

"This paper describes the automation of a mine hoist ore loading pocket using a programmable controller. It provides an introduction to programmable control, and outlines the various modes and operating sequences of the loading pocket. A comparison is made with previous equipment to illustrate the increased flexibility, reliability and diagnostic functions that are gained.IntroductionLoading pockets have evolved from a couple of manually operated air cylinders to entirely automated systems. Early pockets were usually formed in rock, with loading and discharging regulated by air-operated gate s. Interlocks, added to this arrangement, prevented simultaneous operation of the gates and ensured proper hoist position . As the loading pocket advanced, it was recognized that gravity feed posed problems, often becoming plugged or letting water run through into the shaft. A belt conveyor was employed, eliminating the se problems and resulting in greater loading control. Weighing the combination of transistorized logic modules, replaced many relay systems. This elimination of moving parts and contacts increased reliability and reduced maintenance costs.As semiconductor technology progressed, there were major breakthroughs in miniaturization and reliability, and as a result the programmable controller was introduced. Programmable controllers first appeared in the automotive industry in the late 1960's. A system controller was required to replace the large relay panels in operation at that time. The use of digital integrated circuitry enabled these programmable controllers to automate processes with hundreds of inputs and outputs. Advances in electronics reduced production costs , making controllers for smaller application s viable . This development is on-going, each generation introducing controllers with greater capabilities for a wider variety of systems. equipment was the next step in loading pocket development, and dependance on much of the manual control was reduced . The complete system was first automated using relay panels. Solid- state devices were later introduced, and static control,"

Jan 1, 1980

By A. C. Headon, K. W. Lam, D. P. Dautovich

"Microbiological activities affecting the performance of materials have been encountered in diverse situations within Ontario Hydro. Case histories of bacterial problems which are presented include ground rod corrosion at transformer stations, corrosion of a bare steel cooling water intake structure in Lake Huron and corrosion of steel components in a nuclear generation station vacuum building. Possible microbiological activities which may affect the corrosion behaviour of containers for the disposal of nuclear fuel waste in the future are discussed, as are bacterial actions suspected of causing an odour problem in residential water heaters.IntroductionBacteria are ubiquitous. Except by use of sterilization methods, bacteria -free environments are no t possible to find. Bacteria lie dormant in hostile environments, spread easily through air and water currents and reproduce rapidly under favourable conditions. Although different types of bacteria have different preferable conditions for growth, they are highly adaptive and in general, whenever there is a source of water and carbon (carbon dioxide or organic matter), there will be bacterial activities . These activities often induce or enhance costly metallic corrosion in industries and water odour problems in rural water supplies . Underground structures and systems in contact with natural water or water containing organic matter are most susceptible to bacterial attack.The types of metal-degrading bacteria , their characteristics and the conditions for growth have been reviewed extensively in the literature(1,2,3). There are several often encountered groups of bacteria which, through their metabolic processes, may lead to the degradation of metals. A large variety of bacteria produce corrosive in organic or organic acids as waste, such as the well known formation of sulphuric ac id by aerobic sulphur oxidizers . Anaerobic sulphate reducers produce hydrogen sulphide which is corrosive and has an obnoxious smell, slime-forming bacteria from slime which shelters sulphate reducers and iron bacteria oxidize ferrous to ferric ion which precipitates as hydrated oxides creating oxygen concentration cells . The following are bacterial problems encountered in Ontario Hydro. Although the number of recognized cases has been few, they show the diversity of location and environment where bacterial problems could arise. These include ground rod corrosion at transformer stations, corrosion of bare steel in a water intake structure, corrosion of steel in a nuclear generation station vacuum building and an odour problem in residential hot water tanks. In addition, possible bacterial- enhanced corrosion in containers for future disposal of nuclear fuel wastes are also discussed."

Jan 1, 1984