Search Documents

By Fatemeh Saeidi, Luis Marcelo Tavares, Malcolm Powell, Mohsen Yahyaei

"Understanding a single breakage mechanism is fundamental to the development of breakage testing techniques appropriate for mechanistic modelling of any breakage equipment. In the light of this insight, it is also possible to compare any two breakage events in a mechanistic manner. This paper presents a new method to compare breakage mechanisms of two-point impact with compression, different in their applied strain rates. This approach regards a single breakage event as a process affected by three sub-processes; first fracture, capture and spatial distribution of fragments. Spatial distribution is influenced by the kinetic energy of fragments and their brittleness. Using this methodology allows us to examine how each sub-process is influenced by applied strain rate and its impacts on progeny size distribution. For this purpose, two rock types of widely different strength, magnetite and silicate, were tested at various energy levels using the impact and compression mechanisms. To isolate the effect of spatial distribution of fragments, particles were forced to remain in the breakage zone. In this condition, similar progenies were generated from compression and impact mechanisms at similar energy levels. However, allowing natural distribution of fragments, coarser progeny was produced from compression of silicate. Additionally, using this approach provides a physical meaning and explanation for rock strength parameters such as A×b in the t10-Ecs relationship. INTRODUCTIONComminution models are rapidly progressing toward a destination that enables us to explain the complete physics of a breakage process as well as the properties of the ores. Eventually, they will be able to take into consideration the micro-events that take place during the comminution process (Bourgeois and Banini, 2002). Thus, considerable efforts have been made in the last few years in the area of ore breakage characterisation to comprehend and unlock a single breakage process that has been treated as a black box event in the majority of conventional methods. In this paper, an attempt is made to explain the effect of applied strain rate on the breakage properties of rock by using the knowledge that has been gained by understanding a breakage event. This is particularly important due to its application for various comminution devices that operate within a relatively broad range of speed."

Jan 1, 2016

By M. K. Jain, Z. T. Xu, M. Bruhis, V. Hegedekatte

"Strain rate and temperature dependent deformation conditions are present during elevated temperature forming of aluminum and other metallic materials. While many constitutive laws have been proposed to represent such deformation conditions, a closer investigation often reveals their limited applicability in terms of fit to the experimental data, and interpolation within and extrapolation outside of the range of experimental stress-strain curves. This is often because material-specific primary deformation mechanisms of temperature-dependent strain and strain rate hardening are poorly captured. In the present work, the Voce-Kocks constitutive model based on mechanics of dislocations storage and annihilation has been found to be suitable for many metallic materials. The model was modified to include the effect of temperature dependent shear modulus. The modified model is then employed to represent the experimental data obtained from uniaxial tensile tests on AA7075-O sheet at elevated temperatures and strain rates. Also, hot gas bulging tests were conducted to verify the applicability of this model. Further, finite element simulation of the hot gas bulge test was performed by incorporating the model as a user material subroutine. Good general agreement was observed between the experimental and FE model predicted results. Some sources of discrepancy in the prediction are also discussed.INTRODUCTION There has been much interest in light-weighting of automobiles from automotive related industries to reduce overall carbon footprint and increase energy efficiency of the vehicles. Aluminum alloys, and especially the medium-strength 5xxx and 6xxx series alloys, have been the primary focus in the last 3 decades to reach the above environmental goals (Huo, Hou, Zhang, & Zhang, 2016) whereas aerospace industry has traditionally focused on high strength 7xxx series aluminum (Al-Zn-Mg-Cu) alloys for structural components (Deng, Yin, & Huang, 2011). Recently, there has been much interest in high strength 7xxx series aluminum as a replacement for heavier steel automotive structural parts such as A-pillar, B-pillar, side impact beams etc. (Harrison & Luckey, 2014). This is both interesting and challenging since the above aluminum structural parts will need to not only meet impact safety standards but also possess sufficient formability for manufacturing such complex parts. Since the formability of high strength 7xxx series materials is quite poor at room temperature, much interest has focused on improving both formability and final part strength via high rate hot stamping, in-die quenching, and subsequent artificial ageing process steps (Kumar & Ross, 2016)."

Jan 1, 2018

By P. M. May, V. Gella

The deportment and speciation of trace elements during mining and minerals processing is becoming an area of increasing concern with regards to potential health and environment risks. The use of chemical modelling can enhance our basic understanding of the deportment and speciation of trace metals under conditions present in gold processing solutions, and assist in laboratory and field investigations. In this paper, we report the results of chemical speciation modelling using the JESS software package for the trace toxic elements Pb, Cd, Hg, Se and Te in cyanidation solutions of varying salinity and relate the models to experimental data. The speciation of mercury is examined in detail.

Jan 1, 2011

By M. Nzotta, L. Teng, S. Seetharaman, A. Chychko

The objective of the present work is to optimize the EAF practice towards Mo alloying with maximum retention of the alloying element in molten steel. During Mo additions, there were significant losses to the dust (ca 7 %) and to the slag phase (ca 2 %), which had serious economic and environmental impacts. The present work was aimed at designing a suitable Mo precursor, an alternative to ferromolybdenum, as the Mo source and a process sequence for optimal retention of Mo in the steel. The design of the Mo source should be in such a way that low cost raw materials such as MoO3 concentrate have to be used, stable during the addition so that the vapour phase losses as MoO3 are kept minimum and the dissolution of the precursor in molten steel is easy without loss to the slag phase. After thermodynamic considerations, three precursor materials were chosen, viz. CaMoO4, MgMoO4 and Fe2MoO4. Synthetic mixtures of the component oxides in each case as well as pure MoO3 were investigated by TGA and high temperature XRD in order to find out the temperature range in which the compounds were formed. Experiments were also conducted separately where the evolved gases were analyzed. All the three precursors were formed easily and the loss of MoO3 to the vapour phase was found to be extremely low. Addition of the oxide mixtures to steel melts were conducted in three different scales, viz. 16 g, 500 g and 3 tons (induction furnacle). Initial experiments showed that MgMoO4 was not suitable since the Mo yield in the steel melt was not very high. Fe2MoO4 was found to perform best, the Mo yield reaching 98 %. Further trials were conducted in the 65 ton Electric Arc Furnace (EAF) at Uddeholms AB in Hagfors. Mixtures of mill scale, MoO3 and carbon in suitable proportions were added in a pre-determined addition sequence. It was found that, in the actual practice, the Mo yield reached 99 %, equaling in performance the addition of ferromolybdenum. The process offers an effective use of cheaper raw materials and very high Mo yield avoiding a pre-treatment step like the production of ferromolybdenum. This is both cost effective and environmentally advantageous. The process has been patented and is being currently implemented at Uddeholms AB, Hagfors, Sweden.

Jan 1, 2011

By M. Kreuh

An investigation of the pressure pulse spectrum generated by the gas dispersion processes in a Peirce Smith copper converter was undertaken via the simultaneous measurement of four tuyeres using high frequency pressure transducers. The data was captured, stored, and analyzed using digital data processing techniques; including power spectral density plots, band-pass filtering, and a principal component analysis (PCA). The process was characterized throughout by a dominant 3 Hz pulse signature attributed to the formation of lateral gas envelopes. In particular, test tuyeres in the tuyere line tended to operate synchronously at the dominant frequency, regardless of operating conditions tested and despite being distributed along the converter. Synchronous behavior is thought to arise from the acoustic coupling and possible resonance behavior of the gas delivery system on the converter.

Jan 1, 2007

By V. G. Papangelakis, J. E. Dutrizac, G. Azimi

A new model capable of predicting the solubility of calcium sulphate solid phases in zinc sulphate processing solutions from 25 to 95°C was developed. The model uses the Mixed Solvent Electrolyte (MSE) model of the OLI systems software to calculate the mean activity coefficients of the electrolyte species. The model was tested using recently developed experimental measurements. It was shown to predict accurately the solubility behaviour of calcium sulphate in multi-component zinc processing solutions containing ZnSO4, H2SO4, MgSO4, MnSO4, Fe2(SO4)3, Na2SO4 and (NH4)2SO4. The model can also explain the complex effect of coexisting metal sulphates on the solubility of the CaSO4 phases. The model is a practical tool for assessing the process chemistry of a wide variety of complex aqueous processing streams.

Jan 1, 2008

By N. N. Rulyov

"Starting from fundamental principles of colloid-hydrodynamic theory of disperse systems we have shown that application of strongly non-uniform hydrodynamic fields allows to achieve not only faster rates of flocculation of suspension, but also supports significant improvements in the quality of clarified water and separation characteristics of solid phase. Specifically, it has been experimentally proven that the new treatment method based on these principles (then termed as ""ultra-flocculation"") allows:•,Increase the output of thickeners and pressure filters by 1,5-1,7 times;•,Decrease solids fall through into the filtrate in the process of vacuum filtration by 2¬3,5 times;•,Improve the rate of purification of water phase in the upright thickener by 1,5-1,9 times;•,Decrease flocculant consumption by 1,5-3 times;•,Increase the effective operational life time of cloth filters by 3-4 times;•,Ensure sustainable operation of separation equipment, i.e. decrease the sensitivity of process to variation in suspension concentration, as well as to variations of suspension composition and dispersion characteristics;•,Apply flocculant solutions of concentration 2-3 times higher, thus increasing the capacity of equipment used for solutions preparation."

Jan 1, 2004

By Oliver B. Hopkins

"WE HAVE patterned our lives on the things we take from under the earth's surface. Our civilization is built upon the ore from which we obtain our metals and the fuels which power the world as we know it.Today I should like to discuss with you a newcomer to the ancient mining industry. This lusty infant of which I speak is just a century old - the oil industry.While one doesn't commonly think of oil men as delvers in the earth, It was by sinking a shaft that the first oil was obtained commercially in Canada. Men sank a shaft in a ‘gum bed' in southwestern Ontario's Lambton county, not far from Petroilia, and distilled from the gum a burning oil That was just a hundred years ago. The gum was originally liquid petroleum which had seeped to the surface and lost most of its volatile components.Later, the miners dug down to •bed-rock and soon after they were not digging but were drilling wells, as they have been ever since. From the wells they obtained erode oil.What is crude oil? It is not an element like gold, silver or lead, •but a complex mixture of compounds. These compounds are made basically from two elements, carbon and hydrogen, and are called hydrocarbons (Figure 1).The remarkable ability of these. Two elements to combine in different ways gives crude oil its physical and chemical character. The lighter hydrocarbon compounds in it are gases, at normal temperature and pressure, and these are dissolved in the other, heavier compounds."

Jan 1, 1952

By C. Acuña

The case is presented that the key role of frother is control of bubble size in the pulp zone. Compared to water alone, the addition of frother produces a narrower distribution and finer bubble size. An empirical model is presented for bubble size as a function of frother type using a normalized concentration. The model provides a benchmark for assessing operations. There is no agreed upon mechanism of how frothers act to reduce bubble size. Prevention of coalescence is a common explanation and this action is illustrated. The case against the 'coalescence' model alone is presented and a breakup mechanism is introduced based on pilot cell and single bubble studies. Phenomena associated with bubble shape, velocity and surface flows are used to illustrate the force associated with surface tension gradients. Breakup mechanisms resulting from this force are proposed. The concept can be extended to high salt concentrations which also promote small bubbles.

Jan 1, 2007

By A. S. Nortjé

At South Deep Gold Mine longhole stopes are backfilled using a cemented Cyclone Classified Tailings in its hydraulic state. The need to contain the hydraulic fill until cured requires a barricade. Due to the massive size of the stopes, the tailings can exert enormous forces on any such barricade. Barricades have long been in use, but recent failures in Australia and the large rate of filling required at South Deep solicited a robust design. A robust design must examine all foreseeable failures and the barricade must be able to resist all expected and, within limits, unexpected loads. The design should also be simple to construct and cost effective, limiting the impact of construction errors and unnecessary delays to production.

May 1, 2007

By C. J. Havard, G. C. Taylor, D. G. Cook, N. C. Ollerenshaw, D. K. Norris

"The area encompassed by this report is the eastern and northern Cordillera, shown on the composite map accompanying these background papers. It extends from the 49th pm•allel to the Arctic Ocean and from the Rocky Mountain and Tintina trenches to the Interior Plains. The Mackenzie delta is included in the discussions because of the implications of the bedrock geology of the Arctic Plateau and Coastal Plain on the hydrocarbon and mineral potential beneath it.The eastern and northern Cordillera forms the back-bone of the Western Canada sedimentary basin and from it most of the principles of orogenesis and epeirogenesis relating to the understanding of the structural, depositional and fossil record of the basin have been derived. It may be divided roughly into two parts, reflecting basic differences not only in structural style but also in mineral potential. The more easterly and younger rocks generally contain hydro-carbons, coal and non-metallic minerals; the more westerly and older rocks contain metallic and industrial minerals."

Jan 1, 1970

By P. J. Sylvester, S. J. Piercey, S. Maloney, S. M. Brueckner, L. Pilgrim, D. Hyde, G. Ogilvie

The 1806 zone is part of a Au-rich volcanogenic massive sulfide deposit at the Rambler Camp on the Baie \/erte Peninsula, northwestern Newfoundland, and is characterized by high Au grades (3.97 g/t), relatively low Cu and Zn grades (0.60 wt% Cu, 1.17 wt% Zn), and moderate Ag grades (27.83 g/t) at ca. 0.37 Mt ore. Gold and Ag occur as electrum and different Ag varieties including Ag-Hg ± Au alloys, miargyrite, and pyrargyrite that occur often in close proximity to electrum. Additionally, Ag-, As-, Sb-, and Sn-bearing sulfosalts are frequently observed and usually close to electrum. These textural relations strongly favor a syngenetic/magmatic origin for the 1806 zone, despite having a metamorphic overprint.

Jan 1, 2011

By Martin Lebeuf

The phenomena occurring in the cathode and at the cathode surface of aluminum electrolysis cells are very important in regards to cathode voltage drop and cathode wear. In the current study, laboratory-scale aluminum electrolysis cell cathodes were analyzed by X-ray microtomography. This technique allows an excellent visualization of the distribution of different substances, if their respective X-ray attenuation coefficients are different enough. In the current case, the important difference in the mean atomic number between cryolitic bath and graphitic carbon results in good contrasts. The volumetric bath penetration profile, porosity and impurities distribution in the cathode were thus obtained. Furthermore, metallic impurities and bath heterogeneities were observed at the cathode surface. Observations were also made with Scanning Electron Microscopy - Energy Dispersive Spectroscopy (SEM-EDS).

Jan 1, 2011

By John C. Leighton, C. O. Brawner, Doug Stewart

"Despite the availability of established, sophisticated methods for planning and designing stable slopes in rock, comparatively little attention is usually paid to the problems of carrying out the excavation. Blasting should be carefully planned to obtain optimum fragmentation as well as steep, stable working and final pit walls. The principal difficulty facing a blast designer is the lack of prior information about the many critical blasting characteristics of the rock mass. The common practise of trial-and-error lasting will eventually lead to a suitable program, but must be repeated time after time in variable geology. This frequently results in many blast-damaged slopes. Recent research indicates that monitoring drill performance will yield a Rock Quality Index which correlates to a Powder Factor value. The drilling can provide a continual supply of data, reflecting changes in the rock mass which enables the selection of an economical powder factor.IntroductionWhen planning to excavate a large-scale rock slope, engineer s will generally spend considerable effort to produce a safe, feasible and economical design. Much time will usually be spent on the field map ping, 'structural geologic studies, surface and subsurface hydrology, determination of strengths and effective friction angles of discontinuities, and finally checking stability with the aid of mathematical and analytical models. If the rock cut is to be along a transportation corridor, the prime justification for this time and effort is to produce a clean, stable slope which will be safe for those travelling or working beneath it. For the walls of an open-pit mine, there is the additional economic incentive to maintain the steepest stable slope angle for the minimum stripping ratio (Stewart and Kennedy)."

Jan 1, 1982

By R. A. Hemstock

"Simple classification systems are now being used which will describe adequately the surface vegetation, the topography and the peat for any muskeg condition. Good progress is being made in determining some of the mechanical properties of muskeg and it is apparent that the science of soil mechanics will apply largely to these studies. Correlation is also indicated between shear strength as determined by the shear vane tester and vehicle performance. Several tracked vehicles are now available which perform well in muskeg and advances in this field have come rapidly in the past few years. Testing is under way on the largest of all muskeg vehicles -the thirty-five ton Musk Ox. This vehicle will fill the last gap for the oil industry and will make possible the movement of large drilling rigs at any season of the year."

Jan 1, 1960

By R. Burns, A. I. A. Salama, M. W. Mikhail

"Large amounts of oil sand tailings are produced in the Fort McMurray area, including sand, clays, and misplaced bitumen. The objective of the present study (as part of the overall engineered tailings program) is to select and evaluate the role of hydrocyclones in removing most of the solids from the tailings slurry and producing an underflow product containing about 75% solids.Multistage cyclones were evaluated in pilot plant tests. Slurry feeds with different percents solids and increasing ratios of superfines (–44 µm) were used in testing multistage cyclone circuits. A two-stage Linatex separator circuit gave high recovery to the underflow of 98.8% to 99.6% by mass with the desired high solids content in the underflow of 73% to 75% by mass. Changes in feed solids content (20% to 50%) had little or no influence on cyclone underflow recovery and solids content. The keys to achieving such results were the apex control mechanism and operation at relatively low feed pressure (<60 kPa for 23 cm F cyclone) when the feed solids content was high. Increasing superfines above 7% by mass in the feed resulted in a significant reduction in the recovery to the underflow, probably due to the heavy medium generated by excessive amounts of clays in the cyclone. Pilot plant results were better than those predicted by available cyclone simulation models in terms of recovery and solids concentration in the underflow.Increasing cyclone diameter from 23 cm for the Linatex separator to 51 cm for the Krebs cyclone appears to have little or no effect on size cutpoint."

Jan 1, 1997

By I. Lackey

In 2004, Zinifex Budel Zink commenced testing with the objective to increase the precipitation of aluminium in the iron purification stage of its hydrometallurgical zinc circuit, without the use of expensive reagents. Findings from the literature applied to the leach circuit at Zinifex Budel Zink demonstrated that aluminium removal from the leach circuit could be increased by lowering the ferric concentration and acidity in the vessels where jarosite precipitation occurs. An associated increase in copper precipitation was mitigated by limiting the extent to which the ferric concentration was lowered in the vessels where jarosite forms and lowering the ratio of copper to aluminium in the solutions entering these vessels.

Jan 1, 2006

By Randolph A. Pax, Brian Cornish

The operation of grinding mills in an ore processing circuit is supported by monitoring the input and output variables. These can include the feed ore size distributions, ore feed and water addition rates. The outputs can include the discharge undersize density, oversize tonnage rate and the P80 of the discharge. The grinding mill performance is judged by the power draw, recycle rates and discharge grind size. Conditions inside the mill are inferred from loads cells or bearing pressures and past histories. An overall noise value is sometimes used to evaluate the load as well as the occurrence of excessive impacting of steel balls onto the liners/lifters of the mill. This paper presents results of the internal behaviour of a mill using non-contact stationary microphones located close to the mill outer shell (Pax, 2012). The noise generated by a mill can be attributed to a number of events that occur inside these mills and suitably analysed can provide real-time determinations of in-mill behaviour and can provide powerful insights into the operation of the primary comminution tumbling mills. The acoustically determined signals including a specific 'steel' signal, water hold-up, integrated area together with a classification of impact events. Specific results from case studies will show information of the trajectories inside a mill, steel to rock ratio as well as rheology effects. By incorporating a self-consistent understanding methodology for the in-mill processes from an array of microphones, the information can be used to diagnose the dynamic conditions inside a mill.

Jan 1, 2016

By L. Gutierrez, M. Pawlik

The rheology artificial mixtures of bitumen with fine quartz of varying bitumen content, as well as actual oil sand ores, was investigated under different physicochemical conditions (pH, temperature). All rheological measurements were conducted using a Haake Rotovisco VT550 rotational viscometer, connected to a fixture specifically designed to measure properties of settling suspensions. It was found that at low bitumen contents (1 %, wt.) the pH of the slurries was the most important parameter that controlled the rheology of quartz-bitumen slurries. At higher bitumen contents (10%, wt.), it was a combination of high temperature and high pH that gave the lowest apparent viscosities and yield stresses of the model mixtures. These model observations correlated well with the rheology data obtained for slurries of actual oil sand ores. The overall results were discussed in terms of aggregation-dispersion phenomena between bitumen and mineral particles.

Jan 1, 2009

By John S. Stevenson

ZEBALLOS is a relatively new mining camp. It is on the west coast of Vancouver island, approximately 195 nautical miles northwestward from Victoria. Previous to 1934, a small amount of placer gold had been recovered from the Zeballos river and tributary creeks. However, it was not until the winter of 1934-35, when shipments of high-grade gold ore were made from the property of the White Star Gold Mines, Limited, that lode gold mining really began. Since then, several new mines and many promising prospects have been found. Milling in standard sized mills only commenced late in 1938, when the 75-ton mill of Privateer Mines, Limited, and the 50-ton mill of Spud Valley Gold Mines, limited, were first turned over. The most striking feature of the camp is the high-grade quality of the ore as usually mined. At one property, the ore along a drift 650 feet long has ranged from 5.8 ounces per ton to 17.5 ounces, over average vein-widths ranging from 8.3 inches to 14.5 inches in selected blocks along the drift. One . high-grade shipment of 196.6 pounds of ore from the same property contained 142.877 ounces of gold. The present paper deals only with that part of the area in which mining operations are most active, namely the main Zeballos River valley and its tributaries, Spud and Goldvalley creeks. During the summer of 1938, prospecting was carried on beyond this circumscribed area. The geology and early developments in the area have been described in the following reports: (1) CLOTHIER, G. A., Annual Report of the British Columbia Minister of Mines, 1929, p. 376; 1930, p. 441; 1932, p. 205; and 1933, pp. 252-254. (2) GuNNING, H. C., Geological Survey of Canada, Summary Report, 1932, Part A-II, pp. 29-50, Zebaltos River Area, Vancouver Island, B.C. (3) STEVENSON, John S., Annual Report of the British Columbia Min-ister of Mines, 1935, pp. F-38-40. ? ( 4) BANCROFT, M. F., Geological Survey of Canada, Memoir 204, 1937, Gold-Bearing Deposits on the West Coast of Vancouver Island Between Esperanza Inlet and Alberni Canal. (5) STEVENSON, John S., British Columbia Department of Mines, 1938, Lode-Gold Deposits of the Zeballos Area. (6) MAcDoNNELL, G. F., The Privateer Mine, Zeballos; The Miner, Van-couver, B.C., December, 1938.

Jan 1, 1939