Search Documents

By C. Caners

One of the main uses of fossil fuels is in the transportation sector, leading to environmental consequences such as climate change. In order to move towards a more sustainable energy infrastructure, a transition must begin from fossil fuels to renewable fuels, derived from e.g. biomass. One means of facilitating this transition is to develop reforming technology that can extract hydrogen from a suitable fuel that is either fossil fuel or renewable in origin. The hydrogen would be feed to a 'fuel cell' engine that would power the car, truck or bus. One reforming technology that is attractive for automotive applications is autothermal reforming (ATR). Autothermal reforming is the combination of steam reforming and partial oxidation, whereby a portion of the fuel is combusted using a sub-stoichiometric amount of air, and the resulting thermal energy drives the more desirable steam reforming reaction. ATR is attractive for fast start-up, rapid load following and ease of control. ATR also has the benefit of smaller volume and fewer peripheral requirements as compared to other reforming technologies. Recently, a bench-scale gasoline autothermal reformer (ATR) was constructed and tested. This ATR employs a novel design, consisting of three concentric annuli in order to promote heat transfer from the partial oxidation reaction to the steam reforming reaction. Concurrently, a CFD based model (FLUENT) of the ATR that considers the geometric complexity of the reformer was validated. In spite of the use of simplified kinetics, the model predicted well the observed trends in temperature and overall performance. This paper will discuss the use of the model to improve the design of the ATR. The impact of various system parameters upon performance will be investigated along with alterations in the geometry of the ATR. The various tradeoffs in performance and system volume/size will be highlighted in the context of a fuel cell power system.

Jan 1, 2005

By J. M. Skeaff

"The main solution, ore and residue pulp streams in the Rio Algom Quirke I uranium mill at Elliot Lake have been sampled and analyzed for radium-226. Analysis of the ore and leached residues indicates that Ra-226 dissolves and precipitates within the first pachuca tank. A maximum of approximately 0.2% of the Ra-226 in the ore remains in solution during leaching.IntroductionConcern over the acid drainage and radionuclide dissolution problems associated with uranium tailings disposal sites in Canada has prompted investigation into methods for improving current uranium processing practice.Present commercial practice usually involves leaching of the uranium ore with sulphuric acid, ion-exchange separation of the uranyl sulphate complex from the leach liquor and"" precipitation of the uranium as yellowcake. Daughter products of U-238, such as Th-230, Pb-21O and Ra-226 remain with the tailings and undergo long-term dissolution.Table I summarizes the probable behaviour of the radionuclides during milling. The concern here is with Ra-226, because it will deposit in the bones if ingested and is ""thus considered a serious health hazard(1), Similarly, Po-218 and Bi-214, which are daughter products of Rn-222, can be retained in the lungs and are considered to be the principal sources of radiation dosage(2) arising from the inhalation of Rn-222. Previous investigations(3-9l indicate or imply that Ra-226 undergoes redistribution during milling. However, detailed published information on the behaviour of Ra-226 in the uranium milling process appears to be lacking. A knowledge of the behaviour of Ra-226 in uranium mills, particularly during leaching, could lead to improved methods for its control.This paper reports the occurrence of Ra-226 in the Rio Algom mill. The main objectives of the study were to determine (1) the distribution of Ra-226 within the solids, (2) at what point, and how rapidly, redistribution occurs and (3) whether there are high concentrations of Ra-226 in solution."

Jan 1, 1981

By A. L. Irwin

THE disposal of tailing or waste material, which is generally a very large proportion of the ore treated, is a major problem in the location and operation of any concentrating enterprise and especially so where the life of the operation is expected to continue for many years. Many factors need to be taken into consideration in the selection of a tailing site, chief among which are economical handling of the material, subsequent re-treatment of the tailing, and precaution against stream pollution by waste water. The final location of many mill sites bas been governed largely by the selection of a sui table area for tailing storage. The Sullivan concentrator of the Consolidated Mining and Smelting Company is situated about three miles from the Sullivan mine at Kimberley, B.C., and one of the deciding factors in its location at this distance from the mine was the availability of a suitable area in which tailing could be deposited. In view of the indicated long life of the property, a far-sighted policy bad to be adopted in the matter of tailing storage, for not only would it be necessary to accumulate a huge tonnage of finely ground material, but also reclamation for iron recovery at some future date bad to be considered. Some idea of the extent of the problem may be grasped when it is noted that, by the end of 1938, over 18,000,000 tons of tailing bad been impounded in an area of some 200 acres.

Jan 1, 1939

By R. P. Hackl, P. G. West-Sells

Carbonaceous gold ores are particularly attractive for leaching by ammonium thiosulfate as the gold thiosulfate complex is not significantly adsorbed by the organic carbon present in the ore. A technically and economically feasible process for treating these ores with ammonium thiosulfate has been developed. In this process, gold is extracted by leaching the ore with ammonium thiosulfate, the solution is separated from the ore by counter - current decantation, the gold is recovered by precipitation with ammonium sulfide, and finally the gold containing product is upgraded by reacting the elemental sulfur present in the precipitate with ammonium sulfite. The precipitation filtrate is recycled back to the grinding step to close the solution balance. Reagent consumption is not excessive. Besides precipitating gold, the precipitation step removes most deleterious solution impurities and converts a portion of the polythionates back to thiosulfate. This paper discusses the optimization of the leaching, precipitation, and upgrading steps. The results of a 10 kg/h pilot plant campaign are also discussed.

Jan 1, 2005

By S. Itoh, T. Nagasaka, J. Ono

With respect to the recycling of used lead-batteries, a pure lead is required to prepare a lead-calcium alloy electrode for a new maintenance-free battery. The pure lead can be obtained by means of electrolytic and/or pyrometallurgical refining. In the lead electrorefming, antimony is concentrated in anode slime. From the viewpoint of the recycling and recovery of metal values from used lead-batteries, especially from anode slime, oxidation experiments were conducted for pure liquid antimony in the temperature range between 973 and 1373 K to elucidate the oxidation kinetics and mechanism. Furthermore, since lead anode slime generally consists of antimony, lead and bismuth, experiments have been also carried out using antimony-lead-bismuth alloy. The equation relating to the mass transfer characteristics in the gas phase was then applied to analyze the oxidation kinetics. As a result, it was found that the anode slime treatment, that is, an oxidation of antimony concentrated in anode slime followed by vaporization as antimony oxide Sb406, should be operated with higher oxygen partial pressure and sufficient amount of gas flow rate at lower temperature around 1073 K. The feasibility of the oxidation treatment for anode slime has been also discussed.

Jan 1, 2004

In-Country Business Development Agenda ?Siting/Permitting/Operational Planning ?Securing, maintaining, enhancing social license to operate ?Biodiversity conservation and ecosystem services ?IFC Performance Standards ?Environmental, Social, Risk Governance (ESG) ?Climate change plan

Aug 1, 2013

By SangHyeok Han

Selecting the best possible cranes and identifying spatial conflict-free locations on sites can result in productivity and safety improvements for large-scale industrial construction projects. In the current practice, experienced lift engineers select cranes based on the heaviest lift and/or the largest lifting radius of the identified crane. This practice is relatively time-consuming, and optimization of the crane?s use and location is also difficult. There are many factors which need to be considered during the crane selection process, a reality which further complicates the process. This paper presents a framework which aims at developing a decision support system to enhance the crane selection process and collision-free path planning for large-scale construction projects. This paper utilizes an innovative crane selection matrix in order to establish a process for optimized crane selection for construction projects. The study considers more than 40 different factors in order to reduce time and improve safety for crane operations. Following finalization of crane type (mobile crane versus tower crane), a visualization model to simulate crane operation and identify collision-free crane operation paths is proposed. This process can assist project managers to plan the lifting process more effectively and efficiently. A case study-based approach was utilized to demonstrate the proposed methodology. The methodology was tested in the planning and construction process for boiler house structures in Mannheim, Germany. The project entailed numerous challenges: one of the major tasks was to lift a 102-ton load on the top of the boiler structure through crane collaboration; space limitations on site also presented several challenges related to crane selection, location, and operation processes. Based on the project constraints, the proposed crane selection framework, and the visualization models, two tower cranes were selected and successfully implemented in the case study.

Aug 1, 2013

By Gary Walters, Thomas Gonzales, David George, William Davenport, Andreas Siegmund, Suping Yao, Shijie Wang

The previous survey of world copper smelters was in 2016 (Copper, 2016). The copper smelting industry has grown and improved considerably since then, including continuing growth in China and modernization in Japan (Extraction, 2018). Outotec flash smelting and Outotec flash smelting/Kennecott - Outotec flash converting continue to be adopted while newer processes continue to be adopted in China. In addition, some of the world's original flash furnaces have been completely rebuilt (Extraction, 2018). This paper provides recent industrial production data and discusses these new developments. INTRODUCTION A world copper survey was redone in 2016 after a thirteen year lag since 2003. Some of the notable changes were the significant increases in production particularly from China. Since then, several smelters have gone through modernization processes and decommissioning of older technologies. This paper will review the notable changes since the last publication at Cu2016. In the last paper, Copper Smelting: 2016 World Copper Smelter Data, the author gave an audible sigh after observing that copper smelter sites as well as new and notable smelters have been spreading like wildfire in China since 2003. Indeed, seeing is believing. Figure 1 shows the Ningde Copper Smelter (double flashing, 400,000 MT Cu/Year capacity) that started up producing copper in 2018; Figure 2 shows the Nanguo Copper Smelter that is under construction with 300,000 MT Cu/Year capacity (first phase, side blown smelting and continuous top blown converting). We should not only admire the Chinese copper industry’s significant technological developments, but also the copper price support that it has provided throughout this century.

Jan 1, 2019

By A. A. Nourbakhsha

The main application of refractories based on andalusite in ferrous metallurgy are in air heaters of blast furnaces, mobile mixers, and hot-metal transfer, pig iron ladle, steel-casting, and intermediate ladles. Three specific properties of andalusite are very interesting for the production of high-quality shaped and unshaped mullite refractories: being free of water, its crystal a remains stable without changing its density or volume after firing and therefore has no internal porosity .Graphite additives due to its great wetting ability play an important role in raising the property of refractory bodies. In order to improve properties of andalusite graphite bodies, oxidant agent for increasing in hot strength and oxidation resistance can not be avoided. In this research, firstly 8 pig iron ladles from ESC(esfahan Steel company) with different conditions selected and monitored during usage to determine of main factors affecting on corrosion of refractories. Results showed that tap to tap time, undischarged pig iron ,penetrated pig iron are the main ones.Literature studies showed that the graphite addition help to thermal shock resistance and liquid penetration(steel,pig iron) effect. In this research particle size distribution of aggregates containing andalusite and graphite determined by andreazen equation. Then different mixes with different percentage of graphite,Si, FeSi, SiC prepared by uniaxially pressing under 1500kgf/cm2 pressure by adding 4%wt novalak resin and 0.4%wt HMTA as hardner. Samples fired at 1100-1500oC under reduction atmosphere. According to specific standards density, porosity and CCS measured. Analytical tests such as XRD, SEM were carried out on sample selected from point of view of mechanical properties at different temperatures. Results showed that optimized amount of Si and Fe-Si for _-SiC formation in body is 4 and 6 %wt respectively at 1500OC. XRD and SEM analysis on sample with Fe-Si additives showed no destructive phase through the matrix, also SiC additives not only increase oxidation resistance but also no effect on thermo-mechanical properties.

Oct 1, 2011

By E. Goodwin

"Maclaren Forest Products Inc.Lime is commonly used for the neutralization of acid, and the removal of heavy metals in mine waste waters. However, the precipitation of heavy metals as hydroxides must take place under conditions of controlled pH, to produce minimum concentrations of dissolved metals. An account is presented explaining the concepts applied to lime-treatment processes at Bell Mine during the period of a supernatant discharge to Babine Lake; October 18, 1982to January 25, 1983. IntroductionBell Mine of Maclaren Forest Products Inc., Babine Mining Division, an open-pit copper mine, is located on Newman Peninsula, Babine Lake approximately 65 kilometres northeast of the town of Smithers, British Columbia (Fig. 1).A depressed market for copper metal in 1982 forced a management decision to suspend operations at the mine for an indefinite period from October 3 I, 1982. For some time prior to the mine closing date, mine management was concerned about the increasing level of supernatant in the tailings pond , and its possible effects on the stability of the dam when cycloning of mill tailings ceased. Consideration of these potential hazards led to an application being filed with the Provincial Waste Management for a permit to discharge the excess water to Babine Lake. This large lake, an important link with several significant salmon spawning sites, is a major contributor to the British Columbia commercial fishing industry. Jurisdiction for the environmental affairs in the area is shared by the Department of Fisheries and Oceans, the Environmental Protection Service, and the Provincial Waste Management Branch. These agencies were directly concerned in the formulation of discharge permit following joint consultation, and exchange of information with the company on environmental concerns. An approval was finally granted to discharge approximately 1,000,000 cubic metres of supernatant from the tailings impoundment at Bell Mine into Hagan Arm, Babine Lake from October 18, 1982 with a daily discharge not to exceed 9000 cubic metres. Provisions were made that a particular discharge procedure be followed, and that the company would be responsible for setting up a sampling and monitoring program to safeguard the quality of the effluent."

Jan 1, 1986

By John Taylor

"The Highvale Mine in Alberta is owned by TransAlta Utilities Corpora/ion and operated by Mana/fa Coal Lid. It is the largest coal mine in Canada and in 1982 supplied 8.6 million 1onnes of sub-bituminous ""B"" coal to TransAlta's Sundance Ceneraling Plan/. Annual produclion is scheduled to increase in 1983 when the firs/ unit of the new Keephil/s Generating Plant comes on stream and is expec/ed to exceed 11 million tonnes by 1985 when the second unit is commissioned. Coal is mined from several pits in a multi-seam operation. Comprehensive maintenance, drainage and environmental programs form a major part of the operation.IntroductionThe Highvale Mine is located eighty kilometres west of Edmonton, Alberta on the south shore of Lake Wabamun (Fig. I). The mine is owned by TransAlta Utilities Corporation (T.A.U.) and is operated by Manalta Coal Ltd. In 1982, 8.6 million tonnes of coal were supplied to T.A.U.'s 2100 MW Sundance Generating Plant, making it the largest producing coal mine in Canada. By 1985, with two 375 MW units on line at T.A. U .'s new Keephills Generating Plant, annual production is estimated to exceed eleven million tonnes. The generating plants accept crushed unwashed coal from the mine via the coal handling plant system conveyor belts. The coal is classified as sub-bituminous ""B"" and has an average heating capacity of 18.6 MJ I kg.HistoryPrior to 1943 only small scale mining took place in the Highvale area. Between 1943 and 1961 two strip mining companies, Mount Royal Collieries and Continental Collieries operated on the present mine site. Both operations excavated coal along the south shore of Lake Wabamun."

Jan 1, 1985

By Nabeel Khan

Annual oil production from the Canadian Oil Sands in Northern Alberta has been rising for several decades, and more ore and overburden are excavated each year from an increasing number of open pit mines. Overburden meeting certain specifications will be used to dam tailings and fill open pits, but the remaining material must be stored in overburden storage structures (OBSS). Well-designed overburden storage structures are more stable and cost less in the short- and long-term. The purpose of this paper is to explore OBSS designs that will be stable yet economical in the short- and long-term. The geological background of the site is briefly discussed, including the effect of each of the main geologic layers (recently deposited till and muskeg, Clearwater Formation clay shales, McMurray Formation oil sands, and the Devonian limestone) on the slope stability of the OBSS. Cost is considered in the analysis when balancing between minimizing costs (steeper slopes) and acceptable factors of safety (flatter slopes), all the while considering the financial consequences of failure. Potential failure planes are identified and probabilistic analysis is conducted on the critical failure surface. The variations in the factor of safety caused by varying pore water pressure, friction angle, and cohesion, are plotted and discussed.

Jun 1, 2012

By A. M. Cormie

Introduction The purpose of this paper is to give a brief, general outline of mining practices at Torbrit Silver mine. The geology of the mine is touched on as it is felt that a rough picture of the geology will result in a clearer understanding of the mining methods employed. The main part of the paper deals with mining methods and a section is included on haulage. Development practice is mentioned only briefly. Torbrit Silver Mines, Limited, a subsidiary of Mining Corporation of Canada, is located in the Alice Arm area of northern British Columbia. Access to the mine is by boat to the village of Alice Arm at the head of Alice arm, then truck road, following the course of Kitsault river for 18 miles in a northerly direction to the plant site. The main portal is a further two-thirds of a mile along the course of the river, at approximately the same elevation as the plant, 1,014 feet above sea level. Geology The ore occurs in a massive, irregular-shaped quartz-barite body replacing a folded area in a series of volcanic breccias, tuffs, and flow rocks locally referred to as 'green-stones'. A series of parallel, nearly vertical, fine-grained basic dykes cut across the formation at right angles to the strike of the ore belt over a horizontal distance of 140 feet. The whole of the quartz-barite vein material, which ranges up to several hundred feet wide in places, carries silver values but commercial grade is confined to lenses and shoots where there have been more than usual concentrations of native silver and silver-bearing minerals. The ore-bearing structure plunges at approximately 25 degrees along an axis striking roughly N.65°W.

Jan 1, 1951

By G. Beckstead, L. Gormely, R. Zimmer, K. Hanneman, B. Nethery

As part of the EIS and permitting activities for the Pogo Mine in Alaska, a risk assessment study for the water management plan was carried out. The basis for the study was a site water volume and contaminant balance model. Probabilistic modeling was carried out using the @Risk Monte Carlo simulation package to investigate the frequency, quantity, and quality of discharges under varying assumptions. The results were used in discussions with regulatory officials as part of the permitting process for the project. The simulation allows probabilistic modeling of key environmental parameters based on input frequency distributions involving both quality and quantity of flow. When combined with predictions of water treatment plant capacities and removal efficiency, this was very useful for defining the likelihood of important regulatory outcomes. Based on the model, certain project modifications were made. Using the simulation as a basis, ongoing dialog with regulators led to consensus that all potential risks have been considered and mitigated for the Pogo Mine according to their likelihood and severity, and that regulatory requirements would be achieved. The paper describes the model and some of the applications for which it was used.

Jan 1, 2005

By G. Kollberg

"IntroductionThe SALA Caravan Mill system represents a proven concept for the design and operation of mobile and semi-mobile ore dressing plants.The Caravan Mill has been developed to meet the demand for a flexible processing plant to be used for small and medium-sized orebodies or for pilot investigations of deposits directly at the mine site e •The first Caravan Mill installation was put into operation in 1970 and a number of plants have been delivered world-wide since then.The Caravan Mill system has great flexibility both in capacity, ranging from 50 to 1000 tons per day, and in process combinations. The process modules available are:• crushing by jaw and cone crushers;• pre-concentration by the Dyna Whirl Pool dense media system;• grinding by wet rod or ball mills;• separation by gravity, magnetic, flotation or leaching-CVP adsorption methods;• dewatering by lamella or conventional thickeners and vacuum filters.To form complete plants, auxiliary equipment is also available, such as:• bins, feeders and conveying systems;• power generator units;• water tank and pump for process water;• interconnecting piping and cables;• erection and service tool kits;• set of spare and wear parts.For mine sites with rainy or winter conditions, a plastic tent with air heater can be supplied to cover the ore dressing equipment. Each module is workshop assembled complete with slurry pumps, internal pipe work, electric wiring with plug-in connections, hoses, etc., all arranged for quick and simple connection between the units. Before delivery, each unit is tested in the workshop."

Jan 1, 1982

By Isabel F. Barton, Matthew J. Gabriel, Mark D. Barton

Process control, mine-to-mill optimization, and other mining operations depend on having robust, comprehensive mineralogical and chemical characterization. However, current characterization methods rely primarily on analyzing samples from trenches, channels, blast holes, and drill holes and interpolating between them, and are not always sensitive to some minerals (such as clays) that cause major problems for mining and mineral processing. Continuous characterization is possible with techniques such as hyperspectral remote sensing, which measures reflectance or absorption of light in the visible to near infrared (VNIR) and short-wave infrared (SWIR) regions of the electromagnetic spectrum. Absorption and reflectance features are characteristic of different chemical bond types, so each spectrum corresponds to a different mineral or material. In remote sensing, each pixel in the scanned area has both a location and a spectrum. This makes hyperspectral remote sensing potentially useful for characterizing mine site materials. In this study, we tested a hyperspectral remote sensing system as a method of characterizing the mineralogy and material types at mine and metallurgical sites. Our test site was a small open-pit copper mine and leach operation in the southwestern U.S. We scanned mine highwalls, dump piles, leach pads, and nearby rock outcrops with drone- and tripod-mounted VNIR-SWIR spectrometers. We collected ground-truth data through geologic mapping, sampling, and spot analyses with a portable short-wave SWIR instrument. The results show that the hyperspectral remote sensing system that we tested is capable of distinguishing the types and distribution of spectrally active minerals and other materials in diverse mining settings, including showing wet and dry areas of leach pads; clay and carbonate type and distribution on mine highwalls, leach pads, dumps, and rock outcrops; plant type and distribution; fault zones, bedding planes, and other geological features; and qualitative spectral matches between dump piles and areas of the mine highwalls. Hyperspectral sensing proved particularly sensitive to the presence and type of clay and carbonate minerals, which cause geotechnical and metallurgical problems such as highwall failure, gangue acid consumption, and flotation sliming. Examples will be presented and discussed at the conference. Areas of continuing research include automating and streamlining the data reduction process, integrating hyperspectral data with block modeling and mine planning software, and testing the results of hyperspectral sensing in different geological environments.

Jan 1, 2019

By Y. Wang

Phosphates and fluorides are used as regulators for the removal of silicates from diasporic-bauxite both in direct and reverse flotation. While using dodecylamine chloride as a collector, micro-flotation studies showed that sodium hexametaphosphate has stronger depressing power on diaspore than on silicate minerals with increasing sodium hexametaphosphate concentration at pH 6.5, but sodium fluorosilicate shows poor depression on diaspore with increasing sodium fluorosilicate concentration at the same pH. Zeta potentials of diaspore and silicate minerals become more negative both in the presence of sodium hexametaphosphate and sodium fluorosilicate. Adsorption density studies indicated that the adsorption density of sodium hexametaphosphate on diaspore is much higher than that on silicate minerals at the concentration of 75 mg/L. FTIR spectroscopy studies show that sodium hexametaphosphate interacted with the Al atoms exposed on the diaspore and silicate minerals surfaces to form P?O?Al bonds through the P02 groups. It is possible that sodium fluorosilicate interacted through F- or [SiF6]2- with silicate minerals surfaces based on the analysis by AES.

Jan 1, 2006

By C. Bourgoin

"The limited development and application of new technologies to narrow-vein mining is currently impeding progress in the industry to a point where productivity, working conditions and operating costs have reached a critical stage in many Canadian mines.In an effort to foster the emergence and application of new technologies, Université Laval, together with other organizations, has carried out a R&D project focussed on the need of identifying new development pos5ibilities and of facilitating the transfer of technology in matters related to underground mining methods and machinery.The first phase of the study consisted of an in-depth assessment of current practices and problems in narrow-vein mining. The second phase was a state-of-the-art survey of mining methods and equipment, together with proposed modifications and innovations. The third phase of the project concerns the experimental development as well as the principal application of various proposed technologies.This paper presents an overview of the organizational, technical and strategic considerations which guided the University group and it serves as well to introduce a newly-published brochure, entitled ""Underground Mining Techniques of Vein Deposits"", which summarizes such work to date. More specifically, a perspective of technological developments applicable to narrow-vein mining is presented."

Jan 1, 1994

By K. B. Chaudhuri, I. D. Webb, F. E. Rachor, F. A. Sauert

"A characteristic of all methods of copper concentrate smelting is that slags with a high copper content are produced at some phase of the operation. Recirculation to the smelting unit, electric furnace reduction or flotation are at present used on an industrial scale to recover the copper from these slags. This paper describes the application of the top-blowing technique, originally developed by KHD Humboldt- Wedag AG for refining of metallic copper, for the treatment of copper-containing slags. By this method, a mixture of a reducing gas and commercial oxygen is blown onto the melt at velocities which can be supersonic from the tip of a water cooled lance. The impingement of the reaction gas mixture on the surface of the slag forms a depression in the molten phase and a deflection of the jet which brings the slag into a rotating motion. This causes high rates of heat and mass transfer. Results of pilot-plant tests for batch and continuous treatment of slags are presented, and the potential applications of top blowing for industrial-scale operation are indicated. In combination with the cyclone as a smelting unit, this process appears to be economic for smelters of very low capacity."

Jan 1, 1980

By Sigmund J. Andersen, Eva A. Mørtsell, Jostein Røyset, Randi Holmestad, Oddvin Reiso, Yanjun Li, Øyvind Paulsen, Calin D. Marioara

"With the purpose of increasing the extrudability of lean alloys, we reduce levels of the alloying elements Mg and Si in a 6xxx extrusion alloy. To avoid sacrificing strength, we investigate the compensating effect of smaller amounts of lithium and germanium, alone and in combination. Recent studies by atomically resolved high angle annular dark-field scanning transmission electron microscopy (HAADF-STEM) together with density functional theory (DFT) calculations have demonstrated that while Li replaces Mg, Ge substitutes Si in the columns in the hardening ß’’-phase. Several studies have shown that Ge replaces Si in other precipitates as well, and that both Li and Ge promote precipitation and can improve macroscopic properties, like strength and thermal stability. The scope of the current work has been to investigate and document the combined effect of the two alloying elements. Of the investigated alloys, the one containing both elements displayed highest hardness, corresponding with a significant increase in precipitate number density. We used HAADF-STEM to determine the extent of Li and Ge in the precipitate structures.INTRODUCTION The two most important alloying agents, with respect to age hardening of the 6xxx alloy series, are Mg and Si. In general, 6xxx alloys are formed into their final shapes by rolling or extrusion, before being age-hardened at elevated temperatures around 180°C. The hardening effect during this stage is due to the formation of metastable, semi-coherent, precipitate needles along the three < 001>Al directions generally following the precipitation sequence (Marioara, Nordmark, Andersen, & Holmestad, 2006): Supersaturated solid solution ? atomic clusters ? Guinier-Preston-zones (pre-ß”) (Edwards, Stiller, Dunlop, & Couper, 1998) (Marioara, Andersen, Jansen, & Zandbergen, 2001) ? ß” (Andersen, et al., 1998) (Hasting, et al., 2009) ? ß’ (Vissers, Huis, Jansen, & H. W. Zandbergen, 2007), U1 (Andersen, Marioara, Vissers, Frøseth, & Zandbergen, 2007), U2 (Andersen, Marioara, Frøseth, Vissers, & Zandbergen, 2005), B’ (Vissers, Marioara, Andersen, & Holmestad, 2008) ? ß, Si (stable)"

Jan 1, 2018