Search Documents

By D. J. Archambeault, A. Saigal

Substantial cost savings have been demonstrated by material design changes after initial product development. As more information about a product's operating environment becomes available to a designer, it is possible to consider a more costeffective material that still meets or exceeds the design intent, such as minimum low cycle fatigue life. This is especially true in the aircraft engine industry, where precise operating cycle data is not available until after the first engine is built and tested. A methodology for predicting estimated low cycle fatigue life has been developed to investigate potential material change candidates for an aft cooling plate. A twodimensional macromechanical finite element model (FEM) has been developed using ANSYS and used to determine the effects of varying material properties. It is shown that slight changes in density, coefficient of thermal expansion and modulus of elasticity have profound effects on component and effective stresses, and therefore, estimated low cycle fatigue (ELCF) life. Aerospace

Jan 1, 2006

By A. Gutiérrez

At present, most ore milling is done in tumbling mills, consisting of huge cylinders turning on their horizontal axis. This rotational motion causes the ore charge and the grinding balls to interact by impact, compression and abrasion, to reduce the size of the ore. This method is very inefficient since only around 12% of the energy supplied is used for actual grinding, the rest being used in moving the large mass of balls and ore within the mill. This work aimed at better understanding the milling process by evaluating the movement of the load through the Discrete Elements Method (DEM). First, the number of bodies (balls and ore) moving inside the mill is determined, to correlate to the potential impacts that constitute one of the milling mechanisms. Then, the number of high energy impacts is evaluated to correlate to the bodies in motion. At this stage, a differentiation between grinding media and the ore, as well as between the types of contact taking place in the mill, has to be made. This latter issue is of great relevance since from the five identified contact types (ball-ball, ball-liner, ore-ore, ball-ore and ore-liner) only the last three actually contribute to the milling process, the other two causing structural damage to the mill.

Jan 1, 2007

By David F. Machuca-Mory

Modelling the geometry of a vein is a crucial step in resources estimation. The resulting models are used as mineralization domain boundaries and have a direct impact on the tonnage of estimated resources. Deterministic models are often built using time consuming wireframing techniques usually based on hand interpretation of the drillhole intercepts. Another approach consists in coding the drillhole samples by a function of their distance to the veins contacts. The coding is subsequently used for modelling the vein contacts away from drillholes. This is a more efficient approach and is able to provide a measure of tonnage uncertainty. The use of location-dependent variograms improves the modelling by incorporating local changes in the anisotropy of the vein structure. This combined approach results in more realistic vein models, particularly when the geometry of the vein has been are altered by folding, shearing and other structural processes. The approach is illustrated on a realistic case study.

Oct 1, 2009

By Michael Sudbury

Introduction The essence of a good presentation is said to be: Outline what you are going to say Say it Summarize what you said This is perhaps especially good advice at 8.30 a.m. So here goes: This is an attempt to put numbers on three inextricably linked subjects: People and the Future Irrigation and Agriculture Mine Water and Mine Waste

May 1, 2013

By Farnham. G. S.

It is difficult co know how to deal with this subject before a group having such mixed interests. The mining man is not coo concerned with the problems of alloy research. The engineer is more interested in properties of materials than how these properties can be achieved. The business man feels that scientific history and prognostication are not for him, predicting trends or possible developments in the economic field being a more than sufficient occupation. Yet the application of physical metallurgy research to industry is of importance to miner, engineer, and business man, for only through such application can the continuing existence of industries manufacturing or consuming metals be assured. History shows that hard work does not guarantee industrial survival. For instance, the Bessemer method of steel making superseded puddling operations; it, in its turn, has been largely displaced by open-hearth processing; later, steels made in electric-arc furnaces displaced open-hearth products in the quality field; and now, very specialized steels are being made in high-frequency rather than in arc furnaces. It is apparent then, if industry is co remain healthy, complacency must give way co imaginative planning, based on a thorough knowledge of production technique, a knowledge supplied by efficient research.

Jan 1, 1947

By N. Melnyk

IN the past, the Cadomin Coal Company has opened four mines, all in the same coal seam or its folds. Three of these were opened from river level by horizontal entries or rock tunnels, and the fourth, the present working mine, by vertical shafts. This paper deals largely with some operating phases of this fourth mine, with which the writer has been associated. The seam worked here is a thick, steep, bituminous seam, and the writer feels there is a paucity of published data on the mining of such seams. Possible reasons for this are that such seams do not !end themselves to intensive development or mining, there is little chance to mechanize because of the extreme pitch, and operations are fraught with many problems. In addition, the present operations in this particular seam are being carried on at a level below the former workings, introducing new problems, not en-countered on the upper level. Coal will, without question, long continue to be an important factor in the national economy, and some of the best coal is to be found in thick, steep seams. But with the exhaustion of the easily-mined coal near the outcrops, future coal will have to come more and more from lower levels. At Cadomin there is still considerable coal on the second level, below the old river-workings, and there is a possibility that, in the future, still lower levels will be worked. It is the purpose of this paper to indicate some phases of such lower-level operations and to invite discussion.

Jan 1, 1942

By J. E. Danoczi, J. A. Herbst

"Shore Gold Inc. (Shore) is presently designing a diamond processing plant for the Star and the Orion South kimberlite deposits in the Fort à la Corne (FalC) area in central Saskatchewan. The first step in the plant is diamond liberation and occurs in the comminution section. Diamond liberation is the process of breaking up the kimberlite rock, as gently as possible so as not to damage the diamonds.Autogenous grinding mills (AG mills) use a combination of impact crushing, abrasion and attrition to break up the kimberlite. The forces that occur during the actions of abrasion and attrition cause the kimberlites to break up preferentially along lines of weaknesses which offers a “diamond friendly” method of comminution.Hard competent kimberlite is commonly found in the diatreme zone as well as the root zone of the volcanic pipe and is the source of kimberlite for most of the Southern African diamond mines. Softer kimberlite is typically found in and around the crater area of a volcanic pipe and it is this kimberlite that makes up the majority of kimberlite for both the Star and Orion South deposits. These softer kimberlites can be readily broken up using abrasion and attrition imparted by AG mills. In order for Shore to benefit from the softer kimberlite found in the Star - Orion South diamond project, two large (10.97 m diameter x 7.10 m long) AG mills were designed for the comminution section based on extensive test work and simulations by Metso Minerals (Metso)."

Jan 1, 2012

By Dale L. McKinnon, Jean-Pierre Farant

"Dust collectors are used to reduce airborne dust levels generated during crushing at a mining operation and their adequate maintenance is required to ensure effective control of health and safety hazards associated with dusty conditions. Although the pitot traverse technique is commonly employed to balance these dust collectors, the use of an alternative-the equilibrium concentration tracer gas method-is proposed in this paper. This method, which uses sulphur hexafluoride as a tracer gas, can be used to balance airflows in dust collectors and to determine hood collection efficiency accurately and effectively. This technique also reduces some of the errors inherent to pitot tube measurements. IntroductionIndustrial dust collectors are used to reduce dust genera ted by processes like cru shin g, and these must be periodically checked and balanced to ensure continuing effective control of health and safety hazards associated with dusty conditions.To date, the pitot tub e traverse technique has been commonly used to balance air flows in dust collectors. However, this technique is both time -consuming and cumbersome. The equilibrium concentration tracer gas method, described in this paper, is proposed as a viable alternative as it is faster, more reliable, and amenable to automation. The use of tracer gases for such task s is not new. This approach has been used in a variety of mining situations to determine volumetric flow rates in underground openings, leak age through mine stoppings, the effectiveness of face ventilation, pollution migration patterns, mine air recirculation rates, and rock porosity."

Jan 1, 1986

By P. R. Stephenson

Mining projects depend on the amount and quality of the mineral reserves, which in turn depend on the amount and quality of the mineral resources. Only Measured and Indicated Resources may be converted to mineral reserves and Inferred Resources may not, with certain exceptions, be used in economic studies. Responsibility for the estimation of mineral resources rests with the Qualified Person (QP) and there is a wealth of literature, text books and case studies to guide the QP. Responsibility for the classification of the mineral resources also rests with the QP. While there is some industry guidance and common practice on approaches to resource classification on which the QP can draw, the process is (or should be) heavily dependent on the exercise of judgement by the QP. However, this inevitably leads to situations where, for example, one QP?s Inferred Resource is another QP?s Indicated Resource. If the QP?s judgement is poorly reasoned or illogical (as is sometimes the case), it can have a major impact on the project, often with substantial cost or value implications. Project managers and company executives should not unquestioningly accept QP?s classification decisions and should apply the same intensity of due diligence that they apply to other critical elements of the project.

May 1, 2011

By G. Sperlins

"IntroductionBrenda Mines Ltd. is a low-grade open-pit mining and milling operation located near Peachland, B.C. Brought into production in late 1969, the plant treats an average of 30,000 tons per day of an ore that contains 0.130% copper and 0.030% molybdenum.The operation is divided into six areas of responsibility, namely the mine, mill, plant, accounting, industrial relations and purchasing /stores departments.The purchasing and warehousing area handled in excess of 11,000 items valued at $31,000,000 in 198J. Over and above this, the warehousing area issued in excess of 74,000 line items valued at $15,000,000 during that same period.Materials Management- DefinitionWhat is meant by the term ""Materials Management""? Reference to the dictionary will reveal that a material is ""that of which anything is composed or may be constructed; the tools, instruments, implements', etc. for doing something"". Management is defined as ""the act, or manner of managing; the skillful use of means to accomplish a purpose"". Presumably combining these words defines materials management.Of greater importance are the materials managers who will carry out the function. At Brenda Mines Ltd., all employees and suppliers contribute to the materials management function. Each has a specialized knowledge of the materials used in his field. Each has a different view concerning the use and description of the same material. The key is to focus this knowledge so as to make the materials management system useful to everyone."

Jan 1, 1982

By W. T. Gotheridge

The principal sources of coal-dust underground are, of course, coal, and the working of coal. Coal-dust is most dangerous when it is in the finest state of division. This class of dust is found mostly on the roads, being blown or shaken off the loaded trams in transit, or carried in suspension by air currents. The air current passing from the working faces may also carry dust in suspension into the return airway, and the air current from the surface may carry dust from the shakerscreens into the intake airways. The mosl dangerous dust we have to contend with is, (a) that which is most finely divided, and (b) that which contains the most volatile matter, including the inflammable occluded gases, and also oxygen absorbed from the air. According to experiments, coal-dust in a fine and dry state would intensify an explosion, in air free from fire-damp carrying in excess of 3 ozs. of fine dust or 6 ozs. of coarse dust per cubic yard. The volatile matter in the dust must be between 12 and 31 per cent. in the ash-free coal, the latter percentage giving the highest flame velocity. It is vary difficult to propagate flame where coal-dust contains a large percentage of stone-dust, (say 50 per cent.). Shale-dust or other incombustible dust containing no volatile hydro-carbons or carbonaceous matter will prevent the extension of an explosion if mixed with coal-dust in proportion of say 70 per cent., and if the dust is finely divided and dry.

Jan 1, 1924

By Donald Leroux, Robert Grant

"Flotation is a complex and highly multivariate process. Using the conventional OFf (one-factor-at-a-time) technique, the optimization of flotation circuits through laboratory or plant testwork is difficult, time-consuming and therefore, expensive and often results in marginal improvements. The optimal operating conditions can be more efficiently estimated when a systematic approach like SDE (Statistical Design of Experiments) is taken.The concentrator of Noranda's Brunswick Mining Division (near Bathurst, New-Brunswick) is well known for the complexity of its differential copper-lead-zinc flotation circuits. One of them, the chalcopyrite-galena separation (or CuSep) circuit, is impacted by more than 20 variables.Statistical Design of Experiments (SDE) techniques were applied at the laboratory scale to improve the performance of Brunswick's CuSep circuit. Screening tests were conducted using Fractional Factorial designs while optimization tests were carried out based on Response Surface Modelling techniques like the Central Composite design. Every series of tests, without exception, revealed new information and process insights which led to significant circuit performance improvements in the plant So far, the metallurgical gain may be as high as four percentage points of copper recovery (in the CuSep circuit). Potential cost savings of expensive consumables (steam, activated carbon) have also been identified but will require additional circuit modifications before being realized.IntroductionIn spite of its apparent simplicity, flotation is a complex three-phase (solid, liquid and gas) separation process. Fundamentally, it is a highly multivariate process. Industrial flotation circuits are commonly affected by 10 or more process variables."

Jan 1, 1997

By M. M. Papic, J. C. Whitehead

"A sample of Hat Creek coal has been extracted using supercritical aromatic solvents in a laboratory-scale extraction unit. Extract yields in the range 21 to 27 per cent of dry-ash-free coal were obtained.These yields are significantly lower than yields available from high-volatile bituminous coal and some lignites. Thus in a combined extraction/hydrocracking scheme for the production of liquid fuels from Hat Creek coal the char product would exceed that required to supply the energy and hydrogen requirements of the process. Excess char could be used for the production of power or gas for sale.IntroductionThe Supercritical Gas Extraction (SGE) process developed by the U.K. National Coal Board operates in two stages: an extraction stage in which a coal extract is separated from mineral matter and undissolved coal and a subsequent hydrogenation stage.The SGE process is based on the ability of a compressed supercritical fluid to dissolve relatively high molecular weight substrates. It is operated under conditions where a hydrogenrich portion of the coal is selectively extracted in a short residence time extraction stage leaving a hydrogen-deficient char. The process schematic shown in Figure I illustrates that the extract produced is separated from the solvent and passed to a conventional hydroprocessing stage while the char product is utilized in the production of heat, power and hydrogen for the process. An extract yield in the order of 50 per cent dry-ash- free coal represents a ""balanced"" case for such a process in which there is just sufficient char for the provision of these commodities."

Jan 1, 1985

By George Booth

In mining operations the cost of timber is an item of much importance, because the life of mine timbers is, in many cases, very short and, as the supply of the better grades becomes depleted, less durable kinds must be used. This, of course, tends to shorten still further the period of service-ability. While it is possible that concrete and steel may, to some extent, take the place of timber in mines, their high initial cost and the difficulty in installation will greatly restrict their use. Moreover, wood, besides being comparatively cheap to handle, possesses other desirable qualities, and for many purposes a satisfactory substitute is hard to find. Both the decreasing supply and the increasing price of timber make its more efficient utilization imperative. AGENCIES DESTRUCTIVE TO MINE TIMBERS Timber used in mines is exposed to destruction from many sources. Wear, breakage, and waste are responsible for much loss. Wood rollers and drum laggings must be frequently replaced on account of the constant wear by ropes. Unprotected timber in chutes and mills is also rapidly worn by abrasion, and track ties in main haulage ways get worn by the feet of mules, cut by ropes, etc. Large amounts of timber are broken by 'crush' and 'squeeze,' and much temporary timber is buried beyond all recovery in pillar workings and in those mines which resort to back filling. Decay and insect attack, however, cause the greatest damage. If not totally destroyed by one or both of these, the timbers frequently become so weakened that they break under the pressure upon them.

Jan 1, 1926

By J. Dubinski

Passive tomographic imaging is a technique that can be used for assessing seismic hazard in mines with high seismic activity induced by mining. The basic idea behind such an interpretation is the assumption that there is a relationship between high values of seismic velocity and high values of stresses in the rock mass. This relationship was confirmed both in laboratory an in situ measurements and constitutes the basis for rock-burst and seismic hazard evaluation. In the paper seismic tomographic images of seismic P wave velocity and seismic P wave velocity gradient have been presented to determine rock-burst hazard and locate high seismic activity zones in the area of coal panel 306 in Zabrze Bielszowice mine. The zones of high values of P-wave seismic velocity gradient have been found to correlate with the distribution of high energetic seismic events. Passive tomographic images were obtained using modern bent ray tracing tomography algorithm with regularization. Recent study give rise to observation that not only high values of P-wave seismic velocity is important in seismic hazard assessment as many strong seismic events are located in the areas of high values of velocity gradient. This recent observation permits to increase quality of passive tomographic imaging for detection of seismogenic zones and is presented in the paper. The advantage of passive tomography comparing to active tomography is that sources of seismic waves are generated by rock mass itself and costly controlled explosions are not necessary. Another practical limitation of active tomography is the size of study area which usually do not exceed 200 m by 200 m. This restriction does not appear in passive tomography where area of study is usually 2000 m by 2000 m and the tomographic images delineate velocity structure in locations where mining induced seismicity take place. Passive tomography method utilized in analysis of rock mass state in underground mines encounter some difficulties concerned with the numerical stability of optimization algorithms. In the presented approach to passive tomography problem numerical stability is obtained by special regularization method and by application of very stable numerical seismic ray-tracing algorithm.

Aug 1, 2013

By S. Wood

"Plastic Filled Valley (PFV) wire rope represents a significant development over the design of conventional wire rope. A sealing thermoplastic is impregnated under controlled conditions of temperature and pressure into a conventional lubricated wire rope to produce a lattice of plastic which surrounds and separates the strands from each other and from the core. Metal-to-metal contact is thereby alleviated and the lubricant is sealed in. The wear resistance, rope breaking load, fatigue resistance and crushing resistance are all increased. The result is a rope which offers exceptional service life.Laboratory tests carried out in Canada and at the University of Stuttgart, in West Germany, confirm the increase in fatigue life. The field trials conducted so far have indicated that the results obtained in the laboratory can be duplicated in the field.IntroductionIn times of double -digit inflation, the consideration given to operating costs throughout industry commands considerable attention. The same can be said of the mining industry. A set of large-diameter wire ropes used on the huge draglines in strip mining can cost in excess of $100,000. Because a machine may use three sets of rope s each year, it is clear that the costs of wire rope can contribute a considerable percentage to any operating budget. As wire rope is a product which is used extensively throughout the mining industry, it would appear timely to turn our attention to any ""Method of Extending Wire Rope Service Life"" in order that wire rope life can be optimized and wire rope costs can be minimized."

Jan 1, 1982

By J. Mizera, B. Adamczyk-Cieslak, K. J. Kurzydlowski, A. Dobkowska

"AZ31 is the one of the most popular magnesium alloy using in the modern industry. It is well known, that compared with steel, magnesium alloys posse better properties, such as light mass, high specific strength or thermal conductivity. It should be noted that their application is limited by poor corrosion resistance. In this work the corrosion behavior of AZ31 magnesium alloy as cast and after heat treatment were described with the use of testing in neutral salt spray atmosphere.To characterise corrosion resistance and describe layers built on the surface it was necessary to do the metallographic observations with the use of optical microscopy. After that influence of heat treatment for AZ31 corrosion resistance was examined. Measurements were conducted by electrochemical impedance spectroscopy (EIS) and by neutral salt spray tests in artificial atmosphere. Surface and cross section morphology after removal of corrosion products were observed with the use of scanning electron microscopy (SEM).The weight loss measurements show that there is no significant difference between alloys as cast and with following heat treatment.INTRODUCTIONMagnesium and magnesium alloys are popular in modern industry because of the low density and good formability. Magnesium alloys are described by few properties which have got significant influence for their application in transportation and electronics industries (Feliu & Liorente, 2015). Their wide application is limited by poor corrosion resistance. As it is well known Mg is one of the chemically most active metal. Corrosion resistance of Mg alloys depends on several factors, such as impurities, chemical composition or working conditions (Cheng, Qin, Wang, & Zhang, 2009). That all causes that there are many different ways to find well defined and good solution of magnesium alloys processing to improve their corrosion resistance.There are many different versions about the influence of aluminum on the corrosion resistance of magnesium alloy. It is known that intermetallic compounds such as Mg17Al12 due to ß-phase content plays the minor role for corrosion resistance. It is proved ß-phase acts as cathode and it has good ability to build passive layer in broad pH ranges. However it should be noted that mentioned behavior depend on size and distributions of ß-phase in the microstructure (Singh, Singh, & Das, 2015)."

Jan 1, 2016

"Sink-float analysis is often used to obtain yield-ash and density partition curves in the coal industry. These provide a valuable tool for evaluating the performance of a separation process. However, for dense minerals, obtaining complete grade-recovery and density partition curves is more difficult due to the lack of heavy liquids available with the required densities. This paper examines a potential solution to this problem which is to perform batch fractionation of mineral samples in a laboratory-scale REFLUX™ Classifier using high viscosity fluidising liquids. The REFLUX™ Classifier is a gravity separation unit consisting of a system of parallel inclined channels positioned above a vertical fluidised bed. Operated in semi-batch mode, a charge of particles is fluidised from below and particles up to a certain density are elutriated from the top of the system. The fluidisation rate is then increased incrementally to fractionate the sample at progressively increasing densities. Previous work by Hunter et al. (2014) and Iveson et al. (2015) has shown that this method provides excellent agreement with yield-ash and partition curves for coal, especially when glycerol solutions are used as the fluidising liquid. This approach has now been extended to obtain the grade-recovery and density partition curves of high density mineral samples. This method has the potential to provide the minerals industry with an effective tool to evaluate the performance of unit operations separating at cut points higher than the available heavy liquids.INTRODUCTIONMeasuring efficiency and effectiveness is of key importance in the continuous improvement of mineral processing plants. For density based separation, one way the performance of a process can be evaluated is the measurement of density-based partition curves. Currently, this is done in the coal industry using the sink-float method, where heavy liquids are used to fractionate particles into discrete density intervals. However, with high density minerals such as iron ore, liquids of sufficient density are rare, and in most cases also pose serious health and safety concerns to laboratory operators. Most commercial laboratories do not perform sink-float separations above a density of about 4400 kg/m3, the maximum density of Clerici solution without operating at excessive temperatures (Koroznikova, Klutke, McKnight & Hall, 2007; Rosenblum, 1974)."

Jan 1, 2016

By E. You

Kennecott Utah Copper Refinery and Outokumpu Technology have developed a wireless Electrolytic Cell Monitor (CellSensor) system to monitor cell voltage and temperature. The system is based on a robust self-organizing and self-healing wireless network with a very reliable redundant structure. The microprocessor controlled CellSensor device operates off a small amount of energy harvested from the cell bus and requires no external power source. The radio works in the 2.4 GHz international ISM band using robust Spread Spectrum technology. The CellSensor does not require end user calibration of either the voltage or temperature sensors and accuracy is superior to previous systems. The on-board computation power allows digital filtering of the cell voltage signal which results in very high quality data. The system requires much less maintenance than conventional hardwired systems and is intrinsically safer since no high voltage isolation is required. The advanced diagnostic functions allow the device to determine if the bus tap contact is degrading. The CellSensor can also be used for monitoring electrowinning (EW) cells for a variety of metals. CellSensor have been tested for over two years at the Kennecott Utah Copper and Boliden Harjavalta Pori refineries. The CellSensor system is now commercially available through Outokumpu Technology.

Jan 1, 2007

By J. F. Shirley

"Very seldom, if ever, is a molybdenite by-product plant operated exactly the way the process design engineer visualizes it. The best thing the design engineer can do is provide a sound, basic circuit with enough room and flexibility in order that the operating staff can make the necessary modi fi cations to optimize the process. The plant, with minor modifications, should be capable of handling more than one process. This is especially true when the client is having the plant designed for a new process.The writer would like to propose the following ten ""rules-of thumb"" for designing by-product molybdenite plants where the molybdenite is floated out of a copper concentrate. The term rules-of-thumb is used, because there are probably valid reasons for not using one or more of them in a particular plant design. In fact it was 1980 before the writer was all owed to start up a plant where all of these rules were honored in the plant design. This was after 19 years of experience in the design of molybdenite by-product processes and plants. The main reasons for not following the rules are available capital, available space, and the client's experiences based on pilot plant and laboratory test results."

Jan 1, 1981