Search Documents

By X. F. Cao

There was a large reserve of bauxite resources in China. And these resources were mainly the dias-pore-bauxite and contained plenty of aluminosilicate including kaolinite, illite and pyrophyllite. Reducing the contents of aluminosilicate would be significant to the using of Chinese bauxite resources. In this paper, from the single mineral flotation experiments, the surface properties and flotation beha-viours of aluminosilicate including kaolinite, illite and pyrophyllite, using dodecyl amine (DDA), N, N-dimethyl-dodecyl amine (DRN12) and N-dodecyl-1, 3-propane diamine (DN12) as collectors, had been investigated. The flotation results shown that the flotation behaviours of aluminosilicate had been influenced greatly by three amine collectors; and the effect was in the order of DN12>DRN12 >DDA. On the basis of FT-IR spectra and zeta potential measurements, the ionization of surface hydroxyl, as well as isomorphic exchange of surface ions, accounted for the mineral surface charges. And the mechanisms of interactions between the mineral surface and collectors mainly included two modes: electrostatic adsorption and hydrogen bonding; for the DDA and DRN>DDA. 12, the mechanism was mainly electrostatic adsorption; and for the DN12, the mechanisms of electrostatic adsorption and hydrogen bonding both existed. Results of quantum chemistry research shown that the collecting ability of amine collectors was greatly influenced by the electro-negativity of N in the amine molecules; and The |E(EHOMO| and ?E (HOMO-ELUMO) of N atom in DRN12 and DN12 were lower than that of DDA, and the positive charge of ?N group in DRN12 and DA12 were higher than that of DDA. All these calculation results could explain the collecting power of DN12>DRN12>DDA.

Jan 1, 2014

By S. Banisi, O. Farshid, M. R. Rozebehi, A. Bahar, A. Arghavani, M. Mahdavi

At the rougher flotation circuit of the Miduk copper concentration plant (Kerman, Iran) five column cells (CISA) with the diameter of 4m and height of 12m using static mixer type (MicrocelTM) spargers have been installed. Based on the initial design, columns should accept a feed rate of 625 t/h with 80% passing size of 90 µm and solids concentration of 28% and produce 88% of the plant concentrate (i.e., 22 t/h) containing 32% copper. Due to mechanical and processing problems this objective was never realized and theses columns were remained out of operation from the commissioning time (2005). A new attempt with the aim of returning these cells into operation started in 2013. The results of an extensive study indicated that spargers plugging due to the entrance of small amount (2 kg) of coarse particles (up to 2.5 cm) because of usual problems at the plant environment was the main reason of columns non functionality. With a change in the recycle pump inlet design to the column, which prevented the entrance of coarse particles to the spargers, the operation of the column significantly improved. It was found that in order to have a stable operation of the columns at the rougher stage the feed rate for each column should be reduced from 125 (design) to 70 t/h. The air superficial rate had to be also reduced from 1.9 (design) to 0.6 cm/s. A period of 10 days of continuous operation showed that the carrying capacity was 0.23 (g/min/cm2) which was significantly lower that of the design value (i.e., 0.58). The gas hold up was found to be lower than 10% beyond which columns started to move to the turbulent state indicated by "boiling" froth. The average life time of spargers was determined to be 20 days which considered to be very short. The average recovery and concentrate grade of these columns were found to be 68% and 32%, respectively. The high wear rates of spargers, unusually high level of maintenance and supervision needed and instability of the operation made the plant managers not to use column cells as the roughers.

Jan 1, 2014

By Çisem Tuba, Ismail Girgin

"Comparative atmospheric H2SO4 and H2SO4 + H2O2 leaching experiments were performed using a Turkish lateritic nickel ore containing 1.52% Ni. In the leaching tests; acid concentration, temperature and leaching time were considered as main variables and the dissolution behaviour of the ore were studied by Ni, Fe, Co and Mg analyses. The dissolution values in the H2SO4 leaching experiments were observed to increase up to 60% (w/w) acid concentration and a temperature of 95°C. Increase of H2SO4 concentration above 60% at 95°C caused decreases in all the dissolution values and this was attributed to the formation of Fe2(SO4)3 and Fe2(SO4)3•HSO4•H2O type compounds. At the considered optimum H2SO4 leaching conditions ([H2SO4]= 45%, T=95°C, t=45 min); dissolution values reached for Mg, Ni, Fe and Co were determined as 99.12%, 95.58%, 92.63% and 78.37%, respectively. An activation energy of 30.57 kJ/mole was determined for nickel dissolution from the evaluation of the kinetic data obtained for H2SO4 leaching showing that the dissolution was controlled by external diffusion and chemical reactions. Caro’s acid solutions were prepared at H2SO4/H2O2 mole ratio of 3 for varying initial H2SO4 concentrations and leaching tests were performed at 25°C. Co behaved very differently and a dissolution value of 83.94% was obtained even at 5% acid concentration in 60 minutes reaction time. Complete dissolution of Co was obtained after 30 minutes of reaction time at 60% initial H2SO4 concentration and the corresponding dissolution values for Mg, Ni, and Fe were reached to 96.16%, 94.27% and 89.46%, respectively. Although the H2SO4 + H2O2 leaching experiments were conducted at 25°C, it was realized that the temperature of the leaching medium was increased to 122°C after four minutes of reaction time due to probable exothermic reaction(s) at 60% initial acid concentration."

Jan 1, 2014

By I. Gombköto

To sustain the growth of industrial production necessitates the increasing of the amount of processed mined raw and secondary materials. As a side effect of raw material production, the amount of tailings material, - coming from mineral processing operations ? increases as well. Using wet technology, these tailing materials are generally transported and stored with the water used for previous operations. This habit could lead to dangerous situations. Enough to remember the disasters had happened to the last decade, safe tailings operations need to remove as much water from the solid as possible. Environmental, technical and economical needs should meet, therefore using a technology combining these specific needs could be necessary. Paste technology was introduced generally into tailings operations at the last ten years, as an answer to the call of the above mentioned challenges, however there are still many questions to answer within the frame of using it. The Institute of Raw Materials Processing and Environmental Process Engineering of the University of Miskolc has been dealing with mechanical process engineering, especially by the support of the EU project TAILSAFE Contract nº EVG1-CT-2002-0066 and the NKFP 3A/068/2004 Hungarian fund extensive research has been carried out about paste technology. Different test methods and materials were applied. Tested tailings materials were as follows: different fly ashes from coal power plants from Pécs ? Hungary, Gyöngyös ? Hungary, Neyvil ? India, different Croatian ashes, hazardous waste incineration plant ashes from Dorog ? Hungary, different kind of sands from Hungary, fine glass sand from Fehérvárcsúrgó ? Hungary, flotation ore processing tailing from Gyöngyösoroszi ? Hungary. Different additives, as gypsum, bentonite and cement were tested as well. The applied test methods were as follows: physical material testing (laser sizer, piknometer, different microscopes), X-ray diffraction analysis, settling columns, the three measuring pipes tube viscometer (16~27 mm pipe diameter), a hydraulic test loop with different pumps (40~53 mm pipe diameter, 0.2~4 m/s average slurry velocity range, 0%~52 % volumetric concentration range), rotational viscometer, Cassagrande yield locus tester and the slump cone test. This paper summarizes and systematizes the results of the aforementioned research as well as reports about the developed paste pipe transport design method based on the fine suspension ? coarse mixture model. The paper also reports about a systematic experimental series with different materials to establish criteria when high concentration suspensions behave like paste.

Jan 1, 2014

By F. L. Mentg

The utilization of acid leaching tailings was studied. It is obvious that the Fe in acid leaching tailings can be leached into solutions as Fe2+. In this paper, the influence of conditions, including the concentration of ferrous sulfate, pH, temperature and velocity of air flow was investigated. The optimum conditions for preparing seed crystal are as follows: the concentration of ferrous sulfate is 20 g/L; pH is 9.5~10; reaction temperature is 10~20?; velocity of air flow is 0.4m3/h. The optimum conditions for preparing iron oxide red are as follows: the concentration of ferrous sulfate is 5 g/L; reaction temperature is 80~85?; velocity of air flow is 0.13m3/h. At last, the product of iron oxide red could be prepared by ammonia method.

Jan 1, 2014

By Wu Tao, Lu Shijie, Xia Xiaoou, Zhang Ming

The impeller and stator are the most important components that can significantly influence the performance of flotation cells directly. The performance of the impeller and stator of KYF flotation cell is revealed by CFD (Computational Fluid Dynamic) simulation in this paper. A method of obtaining the circulation volume is proposed. The circulation volume is proportional to third power of impeller diameter. And the circulation volume increases linearly with the increasing of the speed. CFD simulation can draw the conclusions that there is a proportional relationship between power consumption, third power of speed and fifth power of impeller diameter. CFD prediction results agree with the theoretical formula. The difference between the forward and backward impeller is analysed in the paper. The circulation volume of the backward impeller is obviously larger than that of the forward impeller under the same condition, but power consumption of the backward impeller is lower. It is demonstrated that the impeller and stator system of KYF flotation cell is an efficient and reasonable stirring mechanism. CFD simulation could be reliably used in flotation cell design and optimization.

Jan 1, 2014

By Shuji Owada, Yang Geng, Natsuko Kuroki

Micro-bubble flotation is considered to be an ideal method for the separation of fine or ultra-fine particles, which are difficult to be separated with conventional flotation and other solid separation technologies. Micro-bubble flotation can increase the probability of bubble-particle collision more than conventional milli-bubble flotation. However, there are also some problems. For example, it is known that the rising velocity of micro-bubble is quite low; therefore, the flotation rate reduces. And also, the bubble-particle adhesion probability becomes lower than that of milli-bubble flotation, which is proved in our prior research. In this paper, we applied ultrasonic irradiation to the micro-bubble flotation system in order to solve the above problems and focused on the bubble-bubble and bubble-particle interactions. For clarifying the behavior of bubble-bubble interaction, bubbles behavior was recorded by high-speed camera under irradiation of various ultrasonic frequencies. As a result, in the case of bubble-bubble interaction, it is proved that bubbles are highly coalesced by ultrasonic irradiation especially in the lower frequency and it can enhance more precise separation. In the case of bubble-particle behavior, it is found that the floatability become higher with the ultrasonic irradiation of higher frequency, and it is indicated that ultrasonic irradiation might improve the bubble-particle adhesion probability. Additionally, it is also found that the apparent CMC of the micro-bubble flotation under the ultrasonic field become much lower with higher frequency than with lower frequency, and it is suggested that the dramatic improvement of hydrophobization is achieved.

Jan 1, 2014

By Kalle Härkki

Sustainability principles in the minerals industry are now becoming more and more important from the perspective of securing a license to operate and enhancing environmental, economic and social performance. This trend is also setting new challenges for the design and operation of future concentrator plants. It is evident that ore grades are declining and ores are becoming more complex requiring new technology innovations and holistic approach for process optimization. There is a demand for more energy-efficient process technologies especially in comminution that is the major energy consuming unit operation in the process chain. Energy is not only a major source of cost but also contributes significantly to the carbon and environmental footprint. There is also an increasing awareness that more intelligent water management is required for reduction of fresh water consumption and mastering the impacts of process water recycling will cause for process performance. In association with water recycling, tailings disposal is an integral part of concentrator plant representing significant environmental and economic issues to the operation. This presentation will discuss general trends and challenges of future minerals processing plants and how innovative technology solutions and better integration of unit processes in conjunction with intelligent process control would contribute to meeting the sustainability challenges.

Jan 1, 2014

By Nicolás Caussade

"The IMPC 2014 slogan "Optimizing Water and Energy Usage for Sustainable Mining" refers to the ever decreasing availability of fresh water and energy, which has turned out to be a crucial aspect in assuring the competitiveness of the mining sector in Chile and the Andes region in general. The concern for sustainability and the supply of water and energy is nowadays part of the top priorities of mining countries and communities. This is also the case for Antofagasta Minerals. Several years ago its mining group implemented an energy policy based on intelligent, strategic and sustainable management, in order to successfully face the challenges imposed by the market. It is called an intelligent policy because it intends to provide energy through a diversified range of sources, which includes the development of in-house alternatives. It is also a policy focused on efficient energy consumption and one that is strategic. Because it is in line with the characteristics of the mining activity, it is developed for the long term. Finally, what makes the policy sustainable is that it gives priority to energy usage from renewable resources and as such, the required capacities have been developed to generate innovative solutions that respond to the restrictions that characterize the industry today."

Jan 1, 2014

By Shuji Owada, Mayumi Ito, Idemitsu Kosan Co. Ltd., Takehiko Nishimu, Sadayuki Shinozaki, Takashi Ando, Tomoe Ota

"fElectrical disintegration (ED) by high voltage electrical pulse is a relatively new technique which was demonstrated by Tomsk and Mekhanobr in the 1960’s and has been investigated in detail by Andres in the 1990’s. In the ED, the electrodes should contact to the targeted material and the energy of high voltage pulse is charged directly to the material. It has been reported that the ED is quite efficient to improve liberation of composite materials, because electrical current passes often through the conductive part and/or along the phase boundaries. Theoretically, the energy required in the ED should be lower than in the other mechanical breakage methods, because breakage occurs basically by tensile strength in the ED while in the other mechanical methods it does mainly by compressive strength which is generally ten times or higher than tensile strength.Coal, involving many kinds of mineral matters, is considered to be one of the targets for the ED to apply to. In Japan, national “Hyper-Coal Project” is now running, in which ultra-clean coal (less than 200ppm of ash, 0.5ppm of Na and K, and 2ppm of Ca) is planned to produce by combining advanced coal preparation and liquefaction technologies for the purpose of direct injection of coal combustion gas to turbine. The ED is one of the major techniques to be developed in this project, since mineral matters must be liberated before introducing to the following advanced separation processes. Liberation is important also for the utilization of middling coals generated from usual coal preparation plants. The application of the ED to the middling coals is considered effective for upgrading these coals with higher liberation degree and less energy input."

Jan 1, 2003

By S. Martins

The aim of this work is to compare three different results of charge motion in a modified 5ft diameter lab mill and to identify differences and similarities in these results. The lab mill is modified from tumbling a ball charge to tumbling a charge of disks. This modification replicates 2D motion. This 2D condition is measured using an instrumented disk (iDisk) and analysed using a video imaging system. The iDisk is equipped with a 3D accelerometer array and rotation rate sensors. With the help of a video system, some measured quantities are also determined externally. The results of these three predictions or measurements are presented. A discussion is included.

Jan 1, 2014

By M. Ranjbar, M. Khosravi Rad, A. Tohry

"The filling degree is defined as the volume ratio of the load inside the mill, which determines the power drawn from the motor, as long as the filling degree is not more than the optimum level. As the filling degree increases beyond the optimum level, the impact energy inside the mill will decrease and as a consequent, the mill power output will also decrease. Therefore, the mill filling degree is a key parameter in evaluating the grinding circuit performance, as it determines the mill reaction to the input feed. Since this parameter has an impact on the mill capacity, measuring the mill load is vital for control and optimization of grinding process. As in Choghart Processing Plant no instrument is available to measure the AG mill filling degree, an empirical model based on the bearing-oil pressure is proposed. The AG mill filling degree was related to the differences between the average pressure of input and output bearings, the circulating load and power drawn. It was shown that a quadratic model could relate the mill filling to the above mentioned measurements. This model showed that when the power drawn and circulating load decreases the bearing-oil pressure needs to be checked. If the bearing-oil pressure increases the feed rate needs to be decreased and steel ball be charged to the mill to increase the grinding and prevent mill overloading. INTRODUCTION The feed quality (size and hardness) affects the grinding process in AG mills. Reducing the top feed size and increasing the ore hardness reduce the mill efficiency and increase the particles with critical dimensions inside the mill. These will result in increasing the mill filling degree and reducing the mill throughput and efficiency (Wills and Finch, 2015). The volume ratio of the load inside the mill is called filling degree, which determines the mill power drawn. It is believed that if more energy is mainly spent on grinding (Wills and Finch, 2015). Therefore the mill power draw is used as a mean to control the mill efficiency."

Jan 1, 2018

By Hamid-Reza Manouchehri, Hassna Aitahmed-Ali, Stellan Sundberg

"In flotation practices as the particle size becomes fine, e.g., p<20µm, the process efficiency declines markedly. When flotation of fine particles is necessary, one method to improve the recovery is selective agglomeration of fines. Different agglomerating methods have been introduced and tested; however, one method which has recently received great attention is to aggregate fine particles by magnetic force. A selective aggregation of the fine paramagnetic particles, e.g., sulfide minerals, can be achieved by applying a high intensity magnetic field during flotation conditioning. The method is simple, selective and effective for fines, and has a low operation cost. However, a minimum magnetic susceptibility of fine grains is required for this process. This method has been demonstrated in different sulfide minerals flotation plants. The implementation of the magnetic conditioning device, ProFlote, in both the Cu-Pb and the Zn circuit of Boliden’s Garpenberg plant in Sweden, where a complex massive sulfide ore is treated, is discussed herein. The preliminary results have shown an increase in the recovery of value minerals, in particular Zn and Ag and considerable reduction in Zn deportment to the final tail. Increases in Cu grade and decreases in Pb grade in Cu-con have been achieved as well."

Jan 1, 2014

By G. P. Wong

"The Inco Matte Separation process was the first commercial application using mineral processing techniques to separate nickel from copper from a slow-cooled matte in Sudbury since 1945. In Inco Sudbury operations, bulk sulphide concentrate containing chalcopyrite, pentlandite, pyrrhotite and some gangue minerals is flash smelted and converted to Bessemer matte. During the controlled slow-cooling of the Bessemer matte, discrete mineral grains of new mineral phases are formed: copper sulfide precipitates as chalcocite (Cu2S), nickel sulfide as heazlewoodite (Ni3S2) and a Cu-Ni-Fe alloy is also formed. Flotation is employed to separate Cc from Hz under high lime conditions (pH>12) with diphenyl guanidine (DPG) as both collector and frother.A simplified matte separation flowsheet is as follows. After grinding, the Cu-Ni-Fe alloy is removed by magnetic separation. All precious metals are recovered in the metallic alloy. Following the rougher flotation, a Cu concentrate is produced after cleaner and re-cleaner flotation in mechanical and column cells. Two Ni concentrates are produced: a high-grade Ni product containing less than 0.8% Cu from the scavenger column tails and a low-grade Ni product containing 5% Cu from the middlings circuit tails. A stream containing the inseparable Cc and Hz from the middlings circuit is generated and recycled back to the smelter. The quantity of this stream is typically about 3% of total feed and can be as high as 5%, greatly decreasing the overall matte separation efficiency. The large mass of the recycle stream is a direct result of poor Cc/Hz separation selectivity in the middlings circuit. The middlings circuit, consisting of a thickener, a regrind mill and two columns, processes two streams: cleaner tailings and scavenger concentrates. The thickener contributes significantly to oxidation due to the long residence time of the pulp in this unit."

Jan 1, 2003

By M. H. Moys, M. M. Bwalya

The use of the Discrete Element Method (DEM) to simulate the interaction of particles in dynamic environments is growing rapidly. This technique is also being applied in the study of milling extensively. However, to date more focus has been on the validation of the model. In spite of the advantages of the detailed information that is available from the simulator, appropriate application of this information remains a daunting task. In this paper a technique that combines particle breakage probability data with the energy spectra generated from the DEM is discussed.

Jan 1, 2003

By Muammer Kaya, Sait Kursunoglu

"Energy is the major concern for society. It is expected that developing country economies and populations will grow and consume more energy. Interest in nuclear power is rising, while the world looks for non-depletable energy source that will not contribute to global warming. However, it still has concerns of nuclear proliferation, radioactive waste and safety. It is necessary to overcome these concerns if nuclear energy is expanded to developing countries. Thorium (Th) utilization as nuclear fuel will be an opening key of these difficulties because Th produces less Plutonium (Pu) and less radioactive waste with enhanced safety. Research into the use of Th as a nuclear fuel has been taking place over forty years, through with much less intensity than that for uranium (U) or U-Pu fuels. Nuclear industry is currently using only 0.7% of the available energy from mined U. With huge resources of Th and relatively little U, Turkey has made utilization of Th for large-scale energy production a major goal in its nuclear power programme. Thorium fuel is plentiful and inexpensive. Energy is major concern for developing Turkish society. Turkey, today exports more than 70% of its energy as fossil fuels. In the last 50 years, Turks are skeptical, anxious and indecisive about having nuclear energy for electricity production. In the last 10 years, Thorium is brought into Turkish government’s attention and national discussion as a new, safe, clean, affordable, CO2-free, alternative, strategic and domestic nuclear energy fuel. Turkey recently contacted four VVER-1200 type Russian Nuclear Power Reactors using U as a fuel in Akkuyu (Rosatom) and another four units will be established in Sinop in the next decade by Japan (Mitsubishi-Westinghouse). Turkish nuclear programme must envisage use of domestic Th as a fertile material. This paper briefly reviews the developments of Th-fuel cycle for nuclear energy from global and Turkish perspectives. Previous Th reserve development and recovery studies from Turkish bastnasite ore are summarized in this paper."

Jan 1, 2014

By Cheng Gan, Gui Xiahui, Li Shulei, Cao Yijun, Liu Jiongtian, Wu Lun

Flotation rate constant is an essential parameter in the flotation process. The fine coal sample utilized in this investigation is anthracite from the Shenhuo mine in eastern China. Fine coal flotation rate tests were conducted to compare the flotation rate constant at constant power input with that at gradually increasing power input. Results indicate that the flotation rate constant decreases with the flotation process and increases as the flotation energy is increased. In addition, the flotation rate constant is close to the maximum value. The increasing trend of the flotation rate constant gradually slows down as the flotation energy input increases.

Jan 1, 2014

By Thomas Pretz, Alexandra Pehlken

Sampling of municipal solid waste is known to be difficult to sample if it has to be representative. When dealing with municipal solid waste, the usual method is to study separately waste material below 40 mm and particles bigger than 40 mm. The material < 40 mm cannot be sorted manual and is termed the “fine fraction”. The particles > 40 mm can be separated manually and are usually sorted into pre-defined groups of materials. These groups can be defined depending on the demand of quality assurance. But standardisation of procedures is not far progressed, even for the widely practised sorting methods.

Jan 1, 2003

By Grigory Voyloshnikov, Sergey Petrov, Vladimir Petrov

"The treatment of high-grade copper gold-bearing ores is practiced extensively. However, due to low concentration of copper the application of a separate process for copper recovery can make this process uneconomical. The copper, in particular: in oxide minerals, intensively bounds with cyanide during conventional cyanidation. In this case, cyanide is not able to react with precious metals and the consumption of cyanide increases. The resulting copper cyanide complexes have a negative effect on the recovery of gold. Due to decreasing of the process parameters, a repeated use of the recycled solutions can be hindered, especially in the case of heap leaching. The technology of copper removal from the process solutions with simultaneous regeneration of free cyanide from copper-cyanide complex and producing of a saleable high-grade copper concentrate was developed. An important feature of this technology is simplicity, the absence of complex or dangerous operations and the use of common reagents. The choice of equipment depends on the ore treatment option: heap or vat leaching. Also, simpler equipment schemes are available. The studies, tests and industrial practice show that if the concentration of copper can be decreased down to the first numbers of mg per ppm or lower, it is reasonable to maintain the process copper grade in the recycled solutions at 30-50 mg/L. In this case, recycling of cyanide-bearing solutions is unlimited. The regeneration of free cyanide from that of bound with copper and other cyanide complexes is 95-98%. The grade of copper in the concentrate is 55-60%. This technology is an economically competitive option, in particular: with the account of the sales of copper concentrate. The removal of copper has a positive effect on gold recovery, especially during heap leaching. In addition to, this offers significant benefits in reduced costs."

Jan 1, 2014

By Yimin Zhu, Dezhou Wei, Haijun Liang, Zhifu Zhou

Pyrite is one of sulfide minerals most widely distributed in the earth. During the flotating separation of metal sulfide and the floating desulfation of coal, it is often requaired to restrain pyrite. However, the result is not very satisfactory because of the little difference of floatability of minerals to be separated. The problem is extremely outstanding for the floating desulfation of coal. Researchers carried out a number of experiments with T. ferrooxidans (Yang et al, 2001; Zhou et al, 2000; Zhou et al, 2001; Wei et al, 2001) for an enhanced restraint to pyrite. The results showed that the T. ferrooxidans after being cultured works the best in restraining pyrite. After 10 min pretreatment, the removal rate of pyrite from coal is up to 80%~90%. The research results by Yuan Xin et al (Yuan et al, 2000) show that T. ferrooxidans can restrain effectively the floatability of pyrite and can reduce the recovery of pyrite from 95% to 8%. Though the restraining properties of T. ferrooxidans to pyrite have been proved by many tests and experiments, there are very limited reports on its restraining mechanism. Thus, a systematic experimental research is carried out in this paper.

Jan 1, 2003