Search Documents

By P. Prakash

A dual-drive planetary mill, which has a rotating shaft that sweeps a circle of diameter 750 mm, has been designed. The planetary mill is powered by a 5 hp motor to rotate the main shaft and a 3 hp motor to rotate the jars. The charge dynamics inside the horizontal-axis planetary ball mill was established using three-dimensional DEM simulations. The simulation results provided data to determine the impact energy distribution and the effect of process parameters such as mill speed and filling. It has been observed that the mean impact energy per unit time increases with rotation-to-revolution ratio, whereas the average number of inter-particle impacts per unit time decreases. The mill was also used to synthesize a variety of powders. Here three case studies of reaction milling are briefly presented: (i) cementite and silicon carbide, (ii) oxide dispersed strengthened (ODS) steel, and (iii) magnetite from blue dust. In each case, the powder was produced by mixing and then milling the corresponding pure components. The phase evolution, particle size distribution, and morphology of particles during milling were studied for various samples collected at different milling times using laser size analyzer, SEM, TEM, and Mössbauerspectroscopy. The results established a convenient way to produce powders of high technological and commercial value.

Sep 1, 2012

By B. McFadzean, K. Moller

"The mechanism whereby thiol collectors adsorb onto a mineral surface has been widely studied. Most of these studies examine the mineral surface at equilibrium state and, often, well above monolayer coverage. However, the formation of species at the mineral surface is a complex process that is both kinetically and thermodynamically controlled. In a typical industrial application, the dosage of collector will be around monolayer level. This study uses isothermal titration microcalorimetry to measure the heat evolved during the reaction of sodium ethyl xanthate (SEX) and sodium isobutyl dithiocarbamate (SIBDTC) and their mixtures with galena and chalcopyrite. The sensitivity of the instrument allows heats of reaction of sub-monolayer quantities of thiol collector to be measured.The study found that both the magnitude and kinetics of the reaction between a collector and a mineral surface was dependent on the type of mineral and the type of collector. Proposals are made for the reactions based on literature and the evidence from this investigation. It was found that when collectors were reacted with mixtures of galena and chalcopyrite, that the magnitude of the reaction was lower compared to that measured for the pure minerals alone. This may be due to galvanic interactions between the minerals, resulting in a passivating effect on one or both of the minerals."

Jan 1, 2014

By Tatyana A. Ivanova, Tamara N. Matveyeva, Anatoliy A. Fedorov, Tatyana V. Nedosekina, Valentin A. Chanturiya

"As native gold resources are depleted, gold-sulfide ores consisting essentially of pyrite, arsenopyrite, chalcopyrite and pyrrhotite become one of the major precious metal sources, being presently estimated to account for more than 40 % of total world gold reserves.The prime objective of flotation of gold-bearing sulfide minerals is to increase precious metal recovery and to reduce the product cost through achieving maximum selectivity of the separation process. Separation of Fe and As sulfides in selective flotation of gold-bearing ore products helps reduce the amount of ore mass being sent to hydrometallurgical processing, and permits of recovering gold from As-free gold-containing pyrite concentrate by using a lower-cost pyrometallurgical procedure.An ingenious methodology purposively developed by the authors for comprehensive assessment of flotation properties, electrophysical characteristics and crystal chemistry features of natural gold-bearing sulfide minerals of different origin has been used in this study.Comparison of the elemental composition, non-stoichiometry and flotation activity of different monomineralic pyrite varieties revealed that samples with negligible impurity content are nearly stoichiometric, and show similar flotation properties. Samples with high Cu, As and Au contents are highly non-stoichiometric and readily floatable, even in a highly alkaline environment. Samples with high surface sulfur content and the most defective crystal lattices, with iron atoms substituting for sulfide vacancies, are most sensitive to depressive action of the alkali.A correlation between the type of conductivity, impurity content and amount of xanthate compounds on the surface and in the liquid phase of monomineralic pyrite and arsenopyrite suspensions detected by the extractive spectrophotometric analysis has been identified and analyzed. Experiments showed that the proportion of cuprous xanthate in sorptive collector layers on sample surfaces increases with increasing Cu content of the samples. In general, pH for pH, overall xanthate sorption on pyrite is greater than on arsenopyrite, with the difference increasing in passing from an acid environment to an alkaline one. A significant decrease in xanthate sorption on arsenopyrite is observed at pH greater than 9, whereas sorption on pyrite markedly decreases at pH greater than 11."

Jan 1, 2003

By Manuel Diaz

"In these difficult times for the mining world, mainly due to the global uncertainty about metal prices and the increased activity of opponents to the mining industry, it is essential that mining companies focus on efforts and strategies that will give them the most flexibility to succeed under the fury of these phenomena. The careful management of systems to control costs, and indicators to measure with great precision actual variations in costs and cash flows, are essential to adequately manage the uncertainty. Similarly, clear corporate and regional strategies designed to maximize cash flow and operating margin will allow the company to be better prepared to face any negative situations caused by declining metals prices, stricter government regulations and increasing social pressure. Gold Fields Limited, a corporation of South African origin and with more than 100 years in the gold mining business, has developed the ability to adapt to large changes generated by different global crisis throughout its history. This occasion will be no different. Given the critical situation of the mining industry in the world today, Gold Fields has embarked on a re-structuring plan at global level that will allow much closer control and real efficiency of production costs. This plan includes the creation of regional business units that allow greater independence for each region while still preserving the standards and cultural values of the Corporation. This presentation will explain why we believe that this approach combines the best aspects of the two styles of business, and what are the expected results. In the Americas Region, Gold Fields currently operates Cerro Corona, in Peru. In addition, the company is considering opportunities for growth in Chile, Brazil, Mexico and Canada."

Jan 1, 2014

By Han Long, He Fayu, Sun Chuanyao

In global mining sector, when people mention "China Factor", usually they refer to China’s huge demands for mineral commodities, which had been driving the world mining industry into late "Super Circle". Few people pay attention to Chinese research capabilities and resources, which actually grows with Chinese economics in last three decades in such a soaring speed that you can simply feel it by the number of papers and attendees in recent IMPCs. In China, currently there are 33 universities and colleges where mineral processing discipline is established, and more than 20 research institutes dedicated in mineral processing area, with the largest number of students, teachers and researchers in the world. Due to the characteristics of Chinese mineral resources, Chinese researchers have made tremendous efforts on R&D of the process and reagents for those low grade, fine dissemination, and complex minerals resources, such as low grade hematite, diaspore, complex poly-metallic sulphides, as well as those minerals rich in China, including scheelite, cassiterite, and rare earth etc. with a special emphasis on the comprehensive utilization. Those research achievements not only successfully commercialized in China, but also have great potential for international cooperation. With continuation of globalization , Chinese government has been encouraging the international R&D cooperation in various areas at all levels, and the funding mechanism is well established with more 400 projects were sponsored in last year,in which,however, the mineral processing related projects are very few. Considering the fact that a large number of Chinese companies or Chinese capitals investing in the mining sector worldwide, more opportunities for international cooperation in this filed wouldbe emerging and increasing, while the factors like complementary, IP, government policy, system and culture difference still need to be addressed properly.

Jan 1, 2014

By D. P. Hatfield, G. de Jager

"Recent developments in image analysis techniques and the power of computer hardware have spurred international interest in the potential uses of image analysis techniques in a range of industrial applications. One of these applications is the control of the complex flotation process. Despite years of work, the flotation process is still poorly understood. Current attempts to control flotation cells focus on consistently duplicating the control achieved by human operators.In human control of flotation two of the dominant visual cues are the froth flow speed and the froth stability. These two factors can be measured and inferred respectively from image analysis of video of the froth surface. Two important hydrodynamic variables for control of the flotation process are the air addition rate and the level of the froth pulp interface.The current work focuses on the relationship between froth flow speed and the rate of recovery of concentrate from a flotation cell. Results are presented that show a strong relationship between flow speed and concentrate yield. These results include tests where the conditions in the cell were not changed, as well as tests involving changes to the cell level and air addition rate. Preliminary results are presented which show a correlation between froth stability and froth percent solids.Future developments of the system will include comprehensive froth texture typing, colour space and stability analyses."

Jan 1, 2003

By Douglas W. Fuerstenau

Some historical sketches of the early development of froth flotation are presented. Flotation technology involves several aspects: chemical control of mineral hydrophobicity, selectivity in flotation, flotation kinetics, flotation machines, and process optimization and control. However, only some aspects of the regulation of mineral flotability by the addition of chemical collectors in some selected cases are discussed. The early contributions to flotation science by Langmuir, Gaudin, Wark, and Taggart are briefly outlined. With a firmer understanding of surface chemistry, electrochemistry, and the electrical double layer, progress has been made in understanding the fundamentals of flotation chemistry, although sound theoretical underpinnings still are needed in these very complex systems. Flotation chemistry is related very directly to the type of mineral being floated since the systems depend strongly on the chemical and physical characteristics of the minerals. Full discussion of chemical reagent phenomena would be in terms of the behavior of naturally flotable minerals, sulfides, oxides, silicates and alumino-silicates, and salt-type minerals. At this time, citing a few cases involving salt-type minerals and oxides, the dependence of their flotation surface chemistry will be discussed in terms of the role of adsorption, surface reaction, and the hydrophobic effect.

Sep 1, 2012

By Nóra Schreithofer, Kari Heiskanen

"INTRODUCTIONThe knowledge of the adhesion forces between particles and bubbles is of key importance in the improvement of flotation models. The development of the Colloidal Interaction Force Measurement Apparatus (CIFMA) opened the possibility to quantify the adhesion forces between particles and bubbles. The aim of this study was to examine the effect of three main variables: the approach velocity, the loading force and the loading time on the adhesion force between an air bubble and a hydrophobized silica particle."

Jan 1, 2003

By Jorge Menacho

"A typical Chilean producer in the Large Copper Mining Industry today is characterized by high production level with economical results decreasing but still attractive. Operational activities are developed within a low-productivity environment, with high cost and complex relationship between the company and communities, government authorities, providers, clients and their own workers. Decreasing copper grades and limited availability of energy, water and workforce are structural problems which require the State intervention in collaboration with the relevant actors and benefits would be evident in the middle or long term. Main opportunities in the short term are found in the sub optimal conditions we have at many plants today. Robust solutions to control existing operational management system as well as to supply systematic optimization options are needed. These should be oriented toward effective fulfillment of specific operational set points and also to reduce variability in crosscutting tasks. Solutions should include easy connectivity to existing information systems as well as to a suite of simulation and optimization tools settled in a highly interactive communication platform. Relevant issues include minimization of specific energy and fresh water consumption, maximization of the use and performance of critical equipments, minimization of damage to environment and control of effective application of good operational practices. Several specific examples are given."

Jan 1, 2014

By Cristian Melipichun, Leopoldo Gutierrez

The effect of the presence of fine particles of kaolinite and montmorillonite on the induction time for attachment of bubbles to particles of a copper concentrate rich in chalcopyrite was evaluated in this study. The results obtained from induction time measurements were correlated with data of concentrate recovery achieved from micro-flotation experiments. The effect of the presence of fine clays on the stability of air-water foams was also studied through measurements of the foam volume generated in a glass column under different conditions of air flowrate and MIBC concentrations. The experimental results showed that induction time values increased under the presence of fine clays. These data agreed with results obtained from micro-flotation experiments that showed that copper concentrate recovery decreased when clay particles were added. Although a complete explanation for these results is not available, the fact that experimental observations indicated that fine clay particles tend to adsorb on gas bubbles, suggests that the interactions between fine phyllosilicate particles and air bubbles have to be taken into account when studying the effect of clays on froth flotation. Foamability tests showed that the presence of fine clay particles increased the foam volumes only at high additions of clays and low dosages of MIBC. The results obtained at higher dosages of MIBC showed that the foam volumes decreased with the addition of clays under all the experimental conditions tested.

Jan 1, 2014

By Ashok M. Raichur, S. P. Vijayalakshmi

"Recent advances in technology and the growing environmental concern have laid emphasis on the usage of fine clean coal. Coal fines are also generated in large amounts during various coal processing operations and are difficult to be treated, handled and disposed. Since most of the operations use water as the carrying medium, the fines so generated contain lot of moisture. Conventional technique for processing coal fines includes flocculation by a polymeric reagent followed by moisture removal using a rotary drum or a pressure plate filter, which produce a product with more than 30% moisture. Polymeric flocculants though required in small amounts, need high shear mixing for good performance and operate only in a narrow pH range. Moreover they increase the viscosity of the solution by many folds. Hence it becomes imperative to emulate newer methods for efficient fine coal processing. One such method is the novel use of microorganisms in coal processing.The present investigation deals with the utilization of two gram-positive microorganisms, Mycobacterium phlei and Bacillus subtilis, as bio flocculants and dewatering aids in fine coal processing. Preliminary characterization done on J-coal and M.phlei showed that they are negatively charged over most of the pH range. B.subtilis was found to possess positive charge below pH 4.7. The adhesion studies proved the high potential of microorganisms for adsorption to surfaces. Adhesion tests were conducted at various experimental conditions by varying parameters like pH and ionic strength of the suspension. Results obtained showed that adhesion is always higher in the presence of an electrolyte like KNO3 and most of the adhesion takes place in 15 minutes. With change in pH the amount of B.subtilis adhering on to J-coal remained almost constant and for M.phlei it decreased at higher pH values. Increase in ionic strength did not increase the adhesion of bacteria. Flocculation experiments confirmed the ability of the bacteria to act as bio flocculants. It was seen that about 98% of the coal settled in about 2 minutes on the addition of bacteria along with the addition of the electrolyte. The electrolyte was found to be indispensable for efficient flocculation of the coal suspension and for the attainment of a clear supernatant after flocculation. Also the optical micrographs revealed the formation of large, tight flocs when the electrolyte is present along with the bacteria. Further, flocculation tests were done in the pH range of 2-10 and the flocculation efficiency was found to be independent of pH."

Jan 1, 2003

By Renato S. Costa, Afonso H. Martins, Flávia D. Mendes

"This paper presents some important aspects regarding the ion exchange treatment of an Ni and Co sulphate acidic liquor using chelating resins. Chelating resins possessing iminodiacetic or bis-picolylamine functional groups were compared in terms of nickel and cobalt recovery. The experimental resin with bispicolylamine functionalities (Dowex M4195) was evaluated with respect to Ni and Co uptake, and compared with Rohm &Haas commercial chelating iminodiacetate acid resin.The use of selective ion exchange to recover metals from sulphuric acid liquors has been studied for a long time. Companhia Vale do Rio Doce (CVRD) has been actively involved in hydrometallurgical applications of IX and has researched in selecting the optimum resin for nickel and cobalt selective removal and the design of a suitable IX circuit. When an IX operation is contemplated for a specific application, it is followed a screening process which generally involves consideration of the solution composition and pH, speciation of the metals in the liquor to be treated and other possible techniques that can be applied to achieve the desired specifications or recoveries. Once a decision has been made to use IX for a specific application, relevant testwork should be done to select the most cost-effective resin and design the IX circuit to achieve the desired criteria. The experimental part dealt with the working conditions, resin characteristics and the influence upon the resin maximum exchange capacity of the following factors: nickel concentration, temperature, pH and resin-to-solution ratio. Based on the experimental data obtained, it has been proposed a innovative technological treatment"

Jan 1, 2003

By Brian Hart, Stamen Dimov

"In refractory ores, a substantial part of the gold content may be present as a sub-microscopic component within the mineral matrix of the various carriers. This type of gold may be present as finely disseminated colloidal size gold particles (<0.5µm) or as a solid solution within the sulphide mineral matrix. Such ores are not amenable to gold recovery by direct cyanidation. In order to liberate the sub-microscopic gold, the ore has to be oxidized before being subjected to gold cyanidation and extraction. Autoclave pressure oxidation (AC POX) of the sulphide ore and subsequent cyanidation is a common technology used to liberate the gold in such refractory ores. The additional presence of active carbonaceous matter in such ores (double refractory ores) represents another major obstacle for efficient gold recovery during the process of pressure oxidation and cyanidation. This carbonaceous matter (c-matter) can adversely affect the gold recovery due to its ability to adsorb, or pre-grob gold from the cyanide solution. Advanced micro-beam analytical techniques such as Dynamic Secondary Ion Mass Spectrometry (D-SIMS) and Time-of-Flight Secondary Ion Mass Spectrometry (TOF-SIMS) have become powerful tools for characterization of different forms and carriers of gold for the needs of the mineral processing industry. Major advantages of these techniques are related to their ability to analyze individual mineral particles and provide quantitative analysis with detection limits in the low ppm/ppb concentration range. This paper describes various micro-beam techniques and procedures implemented at Surface Science Western (SSW) for quantification and characterization of the sub-microscopic gold and the preg-robbed surface gold as part of full gold deportment studies in feeds and process stream products."

Jan 1, 2014

By S. Banisi, A. R. Ghasemi, M. Maleki-Moghaddam

Direct observation of the charge shape and its motion in industrial mills are not possible, it is then customary to use transparent end, small-scale mills (i.e., model mills) to determine the charge trajectory directly by visualization methods. Because of a short length of the model mills, the end-wall effects could introduce a significant bias on the observed charge trajectories and shape. The shorter the mill, the stronger the bias. This could be due to some material bridging between the end walls. In this research, the end-wall effects were investigated by gradually increasing the model mill length and analysing the charge trajectory and shape variation at a given operating conditions (i.e., ball filling, mill speed, liner type). The unbiased mill length was assumed to be beyond the mill length where no significant change observed in the charge trajectory and shape. For all tests, the torque of the charge was also measured by a torque sensor. The special design of the model mill with the diameter of 100 cm made possible to increase the mill length in steps of 3.6 cm up to 21.6 cm. Four types of liners, five steel ball fillings (10, 15, 20, 25, 30% v/v) and three mill speeds (55, 70, 85% of critical speed) were tested. The ball sizes ranged from 4 to 12 mm. The results indicated that when the mill length was below 10.8 cm the end walls prevented the charge from free falling. This resulted in lower impact point angles and lower power draws compared with the case of no end-wall effects. When the same experiments were performed using an iron ore instead of balls with the same size range, the impact of end-wall effects was more pronounced. For an increase of 30% in the speed (from 55 to 85%), the torque due the change in the charge shape decreased by 41% (from 3.7 to 2.2 kgf.m) when mill filling was 30%. At the same operating conditions when steel balls used the torque decreased only by 19% (from 9 to 7.2 kgf.m). This was expected due to irregular shapes of the ore particles which facilitated bridging. Three-dimensional DEM simulations also resulted in the similar conclusions.

Jan 1, 2014

By K. H. Luo, J. Y. Liu

An experimental study on interparticle breakage of three iron ores was carried out by compressive stressing of particle-bed in a piston-die device. The feeds to the particle-bed stressing were five narrow size fractions in the size range of 0.2~3.2 mm respectively and a wide size fraction of 0/4.0 mm. The pressures applied were in the range between 30 and 360 MPa. The results show that the energy absorption of the particle bed increases linearly with the pressure; the increase of the product fineness with the pressure declines as the pressure goes up; and the product size distributions resulting from interparticle breakage of different narrow size fractions have no self-similarity. Using data obtained from the piston-die compressive stressing test, the suitability of a previously-developed material-characterization model for interparticle breakage was verified for these ores. It is shown that the particle-bed compression test conducted with piston-die device in lab-scale may provide a cost-effective way of studying and modelling size-reduction of ore materials by interparticle breakage.

Jan 1, 2014

By Frank van der Meer, Lea Quincke

"High Pressure Grinding is applied to achieve size reduction of the particles by inter-particle breakage and to generate micro-cracks in the product particles as a contributing factor in e.g. leaching or mineral liberation. As alternative to classification, a closed circuit operation for HPGR can be established by product recycling, where a proportion of the coarser edge material and parts of the center material are split-off to be recirculated to achieve a finer final (center) discharge product for subsequent processing steps as ball mill grinding or beneficiation. As a result of the product recycling, the content of fines in the feed material increases and may affect the grinding efficiency in terms of production of fines and the generation of micro-cracks in the particles. In the scope of this paper, the effects of the proportion of fines in HPGR feed on grinding efficiency and micro-crack generation were evaluated. Grinding tests were executed with different feed size distributions, from a fines-void situation (truncated feed) to a fines-abundant situation (high product recycle). The evaluation of grinding efficiency and generation of micro-cracks was done by particle size analysis, Bond Work Index tests, impact tests on HPGR feed and products, and X-ray computed tomography of single product particles. This publication summarizes the main aspects of the outcome of these investigations."

Jan 1, 2014

By Peter Rubie, John Russell

"For many years, optimizing the relining of hard rock grinding mills has been complicated by the large number of variables, the low frequency of relines (resulting in a slow relining experience assessment and review cycle), and the potential economic risk associated with some changes to relining equipment or work practices. A technology that has its roots in the automotive manufacturing industry is being utilized to construct a statistically accurate, configurable, and dynamic simulation of the mill relining process. The detailed effects of various mechanization and process changes can be rapidly modeled and compared. Application of this discrete event analysis technology in the mineral processing industry delivers a range of benefits to many industry stakeholders. For example, mill maintenance managers and contract relining companies can embrace the opportunity to benchmark current performance against world’s best practice. Concentrator plant designers and mill manufacturers, informed by this technology’s scientifically defensible data set, can accurately plan for maximum plant efficiency when designing an infrastructure and equipment combination that truly maximizes annual plant availability. Time-motion studies of grinding mill reline data at mills of varying dimensions, liner configurations, mill relining equipment, operator and tool variables, have been integral to the development of this dynamic simulation tool and its associated data set. Access to mill relining simulation technology will enable mineral processing industry professionals to take advantage of an increased capacity to develop mineral concentrator performance optimisation initiatives within the given financial, physical and technological constraints of the individual concentrator plant."

Jan 1, 2014

By Anatoly F. Usov, Vyacheslav A. Tsukerman

"The Russian scientists have developed a new energy saving method for an efficient destruction of the sturdy and hard materials (rocks, ores, frozen soils, concrete blocks ets.) - the Electric Pulse Discharge method of materials destruction (EPD). The detailed researches of a broad circle of problems connected to development EPD-disintegration of materials of a various nature and area of use are executed. The electrical and power characteristics of process, physical fundamentals of selectivity of a breakdown and destruction are investigated, the means of electric pulse splitting and refinements of materials are developed, the technological efficiency of disintegration of industrial minerals estimated.One of the most important characteristics of the EPD-disintegration of ores is the high selectivity of destruction, which provides a large ratio of useful minerals' grains opening, and at the same time, it destroy them less. This ensures in the subsequent stages of beneficiation of ores considerable increase of the extraction and improving the quality of concentrates.The technological tests of various industrial minerals have shown a possibility the EPD-disintegration, as a process that provides the best efficiency of disclosure of useful minerals in all types of ores. Technological and economic efficiency of the method of ore beneficiation is the highest for difficult beneficiated ores with rather low extraction by existing methods. The increase of extraction in this case can reach several percents. As a rule, at a EPD-disintegration the disclosure of mineral grains happens in earlier stages of material comminution than at a mechanical comminution, and with less damage of products. This promotes a simplifying the process of ore preparation and for reducing the power consumption."

Jan 1, 2003

By Francisco Vicuña, Miguel Becerra, Nelson Iglesias

"The following article presents the development of a dynamic tool for the estimation of Jb/Jc rate (ball filling level / total load filling level) of a SAG mil operating in a single stage mode. Using the methodology detailed in this article, it is now possible to have a dynamic estimation tool in the operation, which enables strategic decision making and achieving a continuous development in process optimization. The estimating of the load filling level (Jc) was conducted using a power model, which in this case corresponds to the C-Model developed by (Morrell, 1993) that was calibrated by measuring the load filling levels (Jc) and balls (Jb) using the FARO laser scanning technology by means of Grind-Out and Crash-Stop procedures during the year 2013 and 2014. Finally, to estimate the dynamic filling level of full charge, Jc, three independent models were developed that allowed to feed the adjusted power model: •,SAG mill discharge grate slot wear model •,SAG mill internal volume wear model •,Ball filling level estimation model."

Jan 1, 2014

By Gábor Mucsi, József Faitli, Imre Gombköto, Sanjay Kumar, Zoltán Molnár, Balázs Ráczkevi, Ádám Rácz

"Generally, fly ash particles are very fine (< 100 ?m), mainly spherical and glassy materials form an outer shell on it. This paper deals with the laboratory investigation of ground fly ash based geopolymer. This material can be applied in many fields, mainly in the construction industry, e.g. non-structural elements, concrete, pavements and products, containment and immobilization of toxic, hazardous and radioactive wastes, advanced structural tooling and refractory ceramics, and fire resistant composites used in buildings, etc. The preparation of fly ash using high energy density milling is presented. Systematic experimental series were carried out in order to optimize the preparation process. The particle size distribution (LPSA) and structure of fly ash (FTIR) and the uniaxial compressive strength ,the permeability and structure of geopolymer product, furthermore the rheology of geopolymer paste were investigated. The product properties were studied as a function of the fly ash fineness. As a result of the investigation the relationship between the grinding circumstances, the ground material properties and the geopolymer characteristics was identified. It was found that the above mentioned physical properties of the geopolymer strongly depend on the grinding process."

Jan 1, 2014