Search Documents

By H. Pearce, A. E. Lewis, A. Ochieng

Hydrodynamics and mixing are fundamental to the operation of mineral process systems such as flotation cells and metal precipitation reactors. The computational fluid dynamics (CFD) technique has been employed in the present work to study the hydrodynamics in a mixing vessel stirred with either a Rushton turbine or a pitched blade impeller. The multiple frame of reference (MFR) approach has been used to model both impellers. A draft tube was used only in the Rushton turbine stirred vessel. The flow profiles for the pitched blade impeller have been studied in three regions; below the impeller tip, at the middle of the tank, and near the liquid surface. The simulation results were compared with literature data obtained using a laser Doppler velocimetry in the three regions of the vessel, and it was found that the model predictions were better in the impeller region. There was a poor prediction of the experimental results in the region closer to the liquid surface; however, this was improved when the turbulence parameter (C2) in the k-e model was set to a higher value. The value of the impeller clearance at which the Rushton turbine generates an axial impeller type flow has been determined and it has been shown that, at this clearance, a draft tube can be used to enhance axial flow in a Rushton turbine stirred reactor.

Jan 1, 2003

By Mingxia Liu, Qi Liu, Tao Jiang

"In addition to physical parameters such as small mass and high specific surface area of fine and ultrafine minerals, chemical parameters such as the adsorption affinity of collectors on the minerals also plays an important role in fine particle flotation. In this study, we have examined collectors with two different ionized groups, carboxylate and hydroxamate, on the flotation of fine niobium oxide (pyrochlore). To facilitate comparison, two hydrocarbon radicals were tested: octyl and oleoyl, which led to four collectors that were studied: octyl hydroxamic acid (OHA), sodium octanoate (C8OONa), oleoyl hydroxamic acid (C18HA), and sodium oleate (NaOl). Small-scale flotation and isothermal microcalorimetric titration measurements were performed to determine the flotation recoveries of different sized pyrochlore and the enthalpic behavior after adsorption of the collectors on pyrochlore. It was found that the flotation performance of the carboxylate-based collectors was generally inferior to hydroxamate-based collectors. Sodium octanoate could not float pyrochlore irrespective of the particle size of the pyrochlore tested. With a longer hydrocarbon chain, sodium oleate was effective to float the relatively coarse pyrochlore (>20 µm) but its collection efficiency dropped sharply for particles smaller than 20 µm. On the other hand, the two hydroxamate-based collectors, octyl hydroxamic acid and oleoyl hydroxamic acid, showed good collecting ability to both the coarse and fine pyrochlore. The isothermal microcalorimetric titration studies indicated a consistent correlation of chain length with floatability of collectors for relatively coarse pyrochlore, as well as a positive relationship between the adsorption affinity and fine pyrochlore flotation recoveries. The key finding of this study was that efficient fine particle flotation could be achieved when strongly chemisorbing collectors were used.INTRODUCTION The first detailed study of the effect of particle size on flotation was made by Gaudin (1931) with sulphide ores. In 1942, Gaudin again demonstrated that (Gaudin et al., 1942) fine particles possess different flotation properties from larger particles. Since then the effect of particle size on froth flotation has been an important research topic by many researchers, e.g., Gaudin (1957), Miettinen et al. (2010), Warren (1976) Jameson (2010), summarizing the behavior of fine particles in terms of their low particle momentum, leading to low rate of collision with bubbles which reduces the chance of adhesion. The suggested remediation methods are mainly based on two approaches: increasing particle size or decreasing bubble size (Warren, 1976). Sand-fine splitting followed by separate flotation treatment of the sand and fines, using deep flotation cells, using starvation quantities of collectors, and using long flotation times, are also strategies to address the problems of fine particle flotation."

Jan 1, 2018

By Andrzej Wieniewski, Cezary Regula, Bozena Skorupska, Krystian Cichy

"In this paper, experiences from Polish non-ferrous metals ores enrichment plants in the copper and blende concentrates quality improvement are discussed. The blende concentrate being produced in ZGH Boleslaw S.A., with Zn content of about 54,5% is characterized by the relatively high magnesium content reaching a level of 1% resulting from the dolomite presence, while for the zinc production by electrowinning a concentrate in which magnesium content should not exceed 0,3% is required. The implemented new technology for the quality improvement of blende concentrate is based on the leaching of zinc concentrate with sulfuric acid aimed at dissolving of the contained dolomite, and then flotation of the leached concentrate. It allows to obtain a concentrate with magnesium content below 0,1% at the simultaneously increased zinc content to about 57,5%. In the paper, laboratory tests results on the development of optimal flotation flowsheet for the gypsum removal and the industrial tests results concerning the process optimization of this flotation are discussed. In turn, the copper concentrate being produced in Polish copper ore enrichment plants KGHM PM S.A., is characterized by the increased organic carbon content - above 8%. It creates problems with the smelting of this concentrate because of difficulties with the heat removal derived from the combustion of organic carbon in the flash smelting process. The implementation of segregating flotation to the industrial practice allows the effective production of two concentrates with the differentiated chemical compositions - a concentrate with increased copper content and reduced organic carbon content for the flash smelting process, and a concentrate with lower copper content and increased organic carbon content for the shaft smelting process. In the paper, conditions of the segregating flotation and the achieved results are described."

Jan 1, 2014

By Mohana Rao Andavarapu

Sandur Schist Belt of Karnataka Craton constitutes a hub of iron ore mining activity. The iron ore deposits of the region are closely associated with Banded Hematite Quartzite (BHQ), Shale, phyllites, & Graywackes. The gradual depletion of high-grade iron ores due to extensive utilization has necessitated the exploitation of low-grade iron ore including BHQ, which are available abundantly in different parts of India. In the present investigation, BHQ samples from Kammaturu mines of Sandur schist belt was studied to assess the possibility of upgrading the iron content to the maximum possible extent, so that it may find the better use in iron and steel industries. The sample collected from the study area analyzing 39.76% Fe, 39.8% SiO2, 0.66% Al2O3, and 1.92% LOI was subjected to beneficiation studies. The mineralogical studies reveals that the samples are predominately consists of hematite as an iron mineral and quartz as gangue mineral. Liberation studies and chemical analysis were carried out prior to the beneficiation process, which is flotation. Cationic Reverse flotation studies were carried out and discussed by varying different process variables such as feed size, depressant, collector cum frother dosage & pH. The results obtained are encouraging with an appreciable improvement in the iron content up to 62.8% Fe with Fe recovery of 50.43%. The concentrate obtained from the flotation can be used for pellet making process.

Sep 1, 2012

By B. K. Mohapatra

Small manganese ore bodies in south Odisha, India occurs both as stratiform and stratabound ore bodies. These two ore bodies show contrasting mineralogical, petrographical and chemical characteristics. Stratiform type of Mn-ores consists of manganese, iron and silicate- phases in approximately same proportion. In contrast, stratabound ore bodies contain a high proportion of manganese oxides, silicates and phosphorus phases. Phosphorus is found within apatite in the stratabound ore bodies while in the stratiform ore it occurs as an adsorbed state with iron phase (goethite). Both ore bodies are low-grade (17-23% Mn) therefore do not have a market value. However, the stratabound ores are enriched in phosphorus (P2O5: >1%) compared to the stratiform ores. Both the ore types were processed through gravity, magnetic and roast reduction followed by magnetic separation techniques. The strata bound ore could be upgraded to 33% Mn from a feed of 23% by combination of dry and wet magnetic separation methods. But the phosphorus content also suits up (P2O5: 1.2%) in the processed product making it unsuitable for further use. The stratiform ores do not respond to either gravity or magnetic separation because of close association of manganese with iron phases. However, this could be beneficiated through roast reduction followed by magnetic separation. An ore with 17% Mn content could be upgraded to 40% Mn with a 42% yield and 78% recovery. The goethite, having phosphorus, converts to magnetite and is retained within the magnetic fraction, thereby reducing the concentration of phosphorus in the non-magnetic fraction, which becomes the product. This report demonstrates the influence of ore petrology in determining the up-gradational potential of manganese ore in the southern Odisha, India. Keywords: manganese ore, physical beneficiation, phosphorus rich ore

Sep 1, 2012

By T. N. Alexandrova

Results of mineralogical-technological research of carbonaceous rocks of Kimkansky precious metal occurrence are presented, on their basis new typemorphic natural and technological microelement associations were revealed using mathematical statistics methods. Keywords: carbonaceous rocks, processing, microelements, flotation, statistical criteria

Sep 1, 2012

By John O. Marsden

"Technology development and innovation has played a crucial role in the copper industry throughout history. The effective development and implementation of new technologies allows mankind to produce copper at progressively lower cost of production at a given feed grade and mineral type. This progress serves to counteract cost inflation/escalation over time and, depending on the magnitude of the cost benefit, allows ore cut off grades to be reduced thereby improving the availability, accessibility and utilization of resources. Two broad categories of technology development and innovation play a key role in this process: (i) incremental improvements and optimization of existing technology provide benefits in the near- to medium-term, and (ii) step change technologies provide value over the longer term. A key issue for potential developers and implementers of new step change technology is how to justify resource allocation and expenditures for such initiatives. This paper examines this issue with reference to specific case studies in the copper industry. INTRODUCTION AND BACKGROUND Technology development and innovation has played a crucial role in the commodity minerals industry throughout history, and none more important than the copper industry. As new, cost-efficient technologies are commercialized, the cost of production in real terms at a given ore feed grade and mineral type decreases. This progress enables ore cut off grades to be reduced allowing lower grade material to be processed economically, which in turn increases the availability and supply of the metal or mineral of interest. Cost inflation/escalation works in the opposite direction, squeezing margins for operations utilizing incumbent technology to process material from a given ore deposit. A prior review by the author considered the issue of technology development and sustainable competitive advantage. This review concluded that first movers and fast followers can achieve competitive advantage for periods of 10-15 years through effective deployment of new technologies (Marsden, 2004). A new, more comprehensive study and evaluation was completed in 2014. This paper presents a portion of the results from the 2014 study."

Jan 1, 2018

By J. Bhattacharya

In many different ways industrial raw materials resources industry as a whole has accepted the principles of sustainable development and has made a commitment to move toward this goal. The critical question now is ?how?? While many companies have adopted policies and are implementing community relations programs, sustainability is not always ?lived? throughout the organization. While traditional programs and commitment from the top are critical, employees within all functional areas can advance sustainability. Individuals can make difference at all organizational levels, and it is this collective action that is so critical for enhanced financial performance as well as the preservation of the industry. Keywords: value chains, sustainability, legislation, auditing process

Sep 1, 2012

By Kwan Ho Kim

In this study, free fall tests are conducted with the objective of understanding the breakage properties of waste concrete for the guide of the direction of the better comminution process. Waste concrete of 75mm×53mm is tested at various drop heights with or without heat pretreatment. Test results indicate that a block of waste concrete does not break by free fall, but eventually breaks by repeated free falls. The number of free falls required for complete separation of large aggregates from the cement mortar considerably reduced when the samples were heated at 400?. Therefore, a great energy saving can be obtained when heating the waste concrete prior to crushing. The energy saving was found to be dependent on the height of free fall but in all cases, was still large enough to offset the additional energy required for heating. Also, it was found that the heat pre-treatment gives an additional advantage in that it produced cleaner recycled aggregates. This may result from easier detachment of cement mortar from the aggregates due to weakening of bonding forces by heating. By analyzing the size distribution of the crushed product, a free-fall breakage model is developed using the particle breakage ratio and the breakage pattern. The developed model can be used to predict and to analyze waste concrete processing circuit.

Jan 1, 2014

By I. A. Agapov, I. S. Anisimov, N. V. Rylov, A. M. Sagitova

"The smelter slags represented silicate crystalline rock with medium to coarse-grained structure with spinifex skeletal network of olivine in hedenbergite matrix. Accessory magnetite, pyrrhotite and copper sulfides chalcopyrite, bornite, covellite, chalcocite and digenite occurred in dissemination in silicate matrix. The sample was studied by optical and electron microscopy with support of quantitative XRD. Modal mineralogical composition included olivine, pyroxene, magnetite, chalcopyrite, quartz, pyrrhotite. Copper deportment showed copper distributed in chalcopyrite (40 %), cuprite (22 %), covellite (21 %), bornite, chalcocite, digenite (5 %), Cu-bearing pyrrhotite (4 %) and spinel (2%). Liberation of copper minerals in the material ground to P80=71 µm was good with over 90 % sulfides in free grains and floatable binaries. The results showed theoretical possibility of 65 % copper recovery by flotation. Conclusion based on mineralogical data was precisely confirmed with flotation tests studies that proved to recover around 60 % of copper to commercial grade concentrate. INTRODUCTION Annual world copper matte smelter slags production is estimated to be millions of tones and contain thousands tones of unrecovered Cu, Zn and significant amounts of Ag and Au. Mineralogical study of one large processing sample of material of historical piles of Cu matte smelter slag was carried out to find possibility to recover copper and define theoretical recovery by flotation. The study of the slag material was aimed to determine possibility of upgrading the material on existing copper flotation plant to develop additional mineral resources. The objectives for mineralogical investigation were to target for best liberation fineness, determine theoretical recovery and possible concentrate quality for sulfide flotation tests. MATERIALS AND METHODS Large representative processing sample was collected by mixing of 120 t of slag material representatively excavated from historical piles of Cu matte smelter slag. The sample was used to define the processing technology to recover copper and gold from the material."

Jan 1, 2018

By Zofia Swierczek

This paper reports the results of a detailed mineralogical study of typical, low-grade Australian nickel laterite run-of-mine ores. Successful development of an effective beneficiation process for upgrading such low grade laterite ores relies on good knowledge of the laterite mineralogy and the value metal(s)? distribution characteristics. Both QEMSCAN and quantitative X-ray diffraction techniques were used to conduct the mineralogical analysis of three types of laterite ores, and the results were compared with those obtained by chemical analysis. Some of the major challenges faced included accounting for the mismatch between the nickel values measured by QEMSCAN and those recorded by chemical analysis. This was primarily due to the relatively low concentration of nickel in the ores and its wide dissemination among several major host minerals in complex association. Careful analysis showed that the limit of nickel detection in iron oxide host mineral grains under normal operating conditions was around 4%. Keywords: nickel laterites, mineralogy, characterisation, QXRD, QEMSCAN

Sep 1, 2012

By V. Hema

Granular materials are widely used in process industries, such as chemical, pharmaceutical, cement, food, detergents, and fertilizers. Mixing, blending, calcining, reduction, heating, and granulation of these materials are frequently carried out in rotating cylinders. In all of these processes, the mixing and segregation of these granular materials is important as this controls the secondary phenomena in the rotating kiln such as heat transfer to the material. A significant amount of work is available in the literature but to date these efforts have not been able to capture the important parameters affecting the mixing and segregation in rotating kilns. In addition, the range of parameter values studied so far is rather limited. Simulations of granular materials are based on either discrete elements or continuum models. The discrete element methods (DEM) combine semi-empirical models for the inter particle interactions with the equations of motion from classical mechanics to simulate the explicit paths of all granules in a rotary kiln, thus yielding realistic predictions of the mixing process. This approach is very demanding computationally, which strongly limits the number of granules and the number of revolutions in a simulation. Continuum models dispense with the discrete particles and can therefore be scaled up more easily. But the constitutive relations that serve as the foundation for continuum modeling are difficult to come by, and often only applicable to specific systems and conditions. Here we have chosen DEM simulation for investigating the mixing and segregation behavior of granular materials in a rotating cylinder. This work is directed towards demonstrating the capability of the prediction of the mixing and segregation behavior of granular materials in a horizontal rotating cylinder through discrete element simulation. Further the effect of particle size and rotational velocity on the mixing and segregation behavior is investigated. The simulation results are quantified in terms of mixing index, mixing rate, segregation index and percolation index. Keywords: DEM simulation, granular mixing

Sep 1, 2012

By Yuriy V. Gulyaev, Galina V. Sedelnikova, Valeriy D. Lunin, Valentin A. Chanturiya, Igor J. Bunin

"Probable mechanisms of disintegration of mineral particles in gold-containing sulphides and benefication products exposed to high-power electromagnetic pulses are discussed. Experimental data are presented to confirm the formation of breakdown channels and selective disintegration of mineral complexes as a result of pulse irradiation, which makes for efficient access of lixiviant solutions to precious metal grains and enhanced precious metal recovery into lixivia during leaching. Experiments with different gold-containing products revealed a synergetic effect of high-power electromagnetic pulses with widely varying parameters and moisture in mineral pores on breaking-up and gold extraction processes for various resistant goldcontaining mineral products.Several series of tests performed in IPKON RAS, IRE RAS and TsNIGRI yielded an absolute gain in precious metal recovery, up to 30-80 % for gold and 20-47 % for silver, with resultant gold recovery as high as 90 %. An essentially new, environmentally safe and energy-saving breaking-up technology has been developed for resistant gold-containing products. This new method would shorten the way from raw minerals to final products and help significantly reduce the cost of these products as it obviates the necessity for using the expensive procedures of energy-intensive and environmentally hazardous oxidative roasting and autoclave breaking-up for ore concentrates."

Jan 1, 2003

By S. Kelebek, A. Khan, J. Caceres, Beckett. D.

"Pyrrhotite in nickel-copper sulphide ores is nickeliferrous and intimately associated with pentlandite. Due to its low nickel content, pyrrhotite rejection is an important step in processing of these ores. In our laboratory, various reagents were investigated for their effect on pyrrhotite depression. Among these, a combined use of triethylenetetramine and sodium metabisulphite was found highly promising.The work described in this paper has two parts. The firs part is a summary of results obtained on process samples from the pyrrhotite rejection circuit at Falconbridge’s Strathcona Mill. The second part involves simulation of the circuit performance based on the reagent conditions used in the experimental work and the concept of split factors.Two sets of reagent conditions were evaluated. The first one involved baseline conditions, simulating the current reagent performance. The second one simulated the impact these new reagents can have on the circuit performance.The simulation results obtained under baseline conditions indicated a good agreement with the current circuit performance. The simulation results suggest that at practically the same pentlandite recovery and tailing grades, the circuit concentrate nickel grade can be doubled through effective pyrrhotite rejection by these new reagents."

Jan 1, 2003

By U. M. J. Boin, E. V. Verhoef

Pyrometallurgical reactors constitute a key processing component in the total primary and industrial/recycling resource cycle, being involved both in primary smelting, converting and extraction, as well as the reprocessing of scrap, from aluminium cans to end-of-life automobiles. Therefore the pyrometallurgical reactor?s role in achieving sustainability is the central theme discussed in this paper since optimising their operation minimises waste, residue and offgas (NOx, dioxin, CO2) and maximises product quality and therefore efficiency. To effectively control the overall resource cycle, one needs to take a systems modelling approach of the whole cycle, seeking to also understand the dynamic process behaviour of the individual components of the cycle, and then especially the part that contributes most to the chemical conversion, namely the pyrometallurgical reactor. This paper highlights the role of pyrometallurgical thermodynamics in the whole resource cycle and specifically places equilibrium thermochemistry in the context of process dynamics where large, variable inventories are recycled or maintained within the system. This paper will therefore review the semi-empirical dynamic modelling tools, which are used to model complex systems with the specific goal of developing dynamic predictive models, which also include slag-alloy chemistry, towards controlling the recycling in a feed forward manner. To illustrate the primary production of metals, high carbon ferrochrome and Ni-Cu-matte smelting will be presented as a brief case study. Also fundamental studies in blast furnace and waste incineration kilns will be given. It also will show how the distributed nature of the chemistry of melts in the case of primary extraction, and industrial (recycling) materials such as recycled end-of-life vehicles, have a significant impact on the process outcomes and model predictions. It is therefore argued that the fundamental thermodynamics and kinetics in metallurgical reactors play a final crucial role in modelling the closed material cycle, but only when it is used in conjunction with process systems theory based on reconciled data for parameter estimation and model calibration. System models for aluminium and car recycling will be given as well as a dynamical system model that describes the interconnected material flows for Ag, Au, Bi, Cu, Fe, Ni, Pb, PGM, Sn and Zn for a study on lead-free solder.

Jan 1, 2003

By P. Oliveira, A. Peres, A. Silva

"The decrease in iron content and increase in contaminants grade, associated with greater participation of compact and semi-compact materials, has impacted the recovery of a mechanical cells flotation circuit in the Iron Quadrangle, Brazil. The recovery decrease in the flotation stage motivated the current conventional flotation circuit reevaluation seeking alternatives to restore the recovery, without affecting the final concentrate quality parameters, with low investment. Sampling, chemical characterization of samples, bench scale flotation experiments, and mass balances were conducted. Analysis of the results showed opportunities to improve the circuit performance. The stages prior to the flotation circuit changes were: rougher, cleaner, recleaner and scavenger. In the previous configuration, recleaner was operated as cleaner scavenger and the iron grade in the scavenger concentrate was 23%, representing 38% of the new feed. After the circuit change, the circulating load was reduced from 38% to 15% and the iron content was upgraded to 42%, resulting in increased residence time. The iron content in the global tailings of the concentrator was decreased from 10.9% (year of 2013 average) to 10.2%, representing gains in both mass and metallurgical recoveries.INTRODUCTIONRegarding plant practice, the year 1972 represents a landmark for the concentration of iron ores in Brazil. VALE started up 28 units of WHIMS (wet high intensity magnetic separators) at the Cauê plant in Itabira, each one producing 1x106 t/year of concentrate. Later 17 WHIMS machines were commissioned at Conceição. During the 80’s decade of last century, changes in the ROM required the addition of a cleaner flotation stage to decrease the silica content in the pellet feed.The first company to use reverse cationic flotation as the only concentration operation of iron ore was SAMARCO (start up in 1977). Since 2015 flotation has been utilized at VALE in Itabira as major concentration process, magnetic separation acting as scavenger stage.The Jones matrix type WHIMS were manufactured for decades under patent by KHD Humboldt Wedag. After the expiration of the Jones patent, Eriez Magnetics took the world leadership regarding WHIMS manufacturing. The Brazilian branch of Eriez is Inbras. Based on plant practice experience at the Fabrica concentrator, the Brazilian company Gaustec was established (RIBEIRO and RIBEIRO, 2010) and is now present in different countries. The mega sized WHIMS GHX-1400 (18.000 Gauss, gaps smaller than 1.5 mm) were developed to face the challenge of huge throughput required by iron ore processing (Ribeiro et al, 2017)."

Jan 1, 2018

By S. M. Narbekova, L. V. Semushkina, Zh. A. Aldybayeva, A. A. Mukhanova, D. K. Turysbekov, N. K. Tussupbayev

More complex and heavy-concentrating oxidized and mixed sulphidic oxidized ores are involved in production because of increasing needs for non-ferrous metals. Extraction of the oxidized minerals of non-ferrous metals general in current technologies. The problem is solved to oxidized polymetallic ores the preliminary selective sulphidization is the oxidized surface of the components by means of hydrogen sulphide, sulphide and calcium polysulphide, and also element sulphur, etc. The task was to study details of flotation of the oxidized lead-bearing ore of the Zarechnoe deposit (Kazakhstan) with calcium polysulphide as sulphidation. According to chemical analysis initial samples of the ore contain, %: lead – 4.8; zinc – 0.1; general iron – 0.81. Phase structure lead is characterized by the oxidized form of 57.76-64.5 %; by sulphidic status of 25.5-32.64 %, and by plyumboyarosite of 19.0-23.02 %. Researches on flotation beneficiation of oxidized lead-bearing ore are conducted. Sulfidizator gave to grinding, on flotations there were used the collector (butyl xanthogenate of sodium) and frother (T-80). Experiments were conducted with a new sulphidizator – calcium polysulphide. The latter is obtained by interaction of CaO calcium oxide with sulfur and water at high temperature with component mass the following ratio S:CaO:H2O =10:5:85. Extent of mill initial ore was optimised (88.42 % of - 0.071 mm grade). For the optimum mill mode the studies on matching of an optimized consumption of sulphidizators are performed. On basic technology with application of sulphide of sodium as a sulphidizator at optimum mill, the lead concentrate with the content of lead 64.4 % at extraction of 86.6 % was received. The content of cerussite in a concentrate was about 14.9 % at extraction of 82.1 %. With application of calcium polysulphide as a sulphidizator the lead concentrate with the content of lead 68.0 % at extraction of 88.0 % was received. The content of cerussite has made 16.0 % at extraction of 85.0 %. Application of a new sulphidizator allows to increase extraction of lead in a concentrate from 64.4% to 68% and cerussite extraction – from 82.1 % to 85.0 %. The possibility of application of calcium polysulphide as a sulphidizator instead of conventional sulphurous sodium was established.

Jan 1, 2018

By Vishal Shukla, Ashok Kumar, C. Raghu Kumar, D. P. Chakraborty

"Traditional iron ore beneficiation plants using washing, screening, and jigging processes require large volumes of process water. Generated slime during processing, its disposal and impact on water usage, is an important concern for any mining company. The challenge today, during extracting iron ore, is how to dispose of slime such that it is contained and stable, while maximizing water reuse and minimizing surface footprint. The slime disposal methods are sensitive to the environment. Two major technologies presently being practiced for disposing the slime across the world are pressure filtration and paste thickening. In this perspective an attempt has been made to do comparative study between paste thickening and pressure filtration for selection of suitable slime disposable technology for Noamundi processing plant, Tata Steel. From the studies, it is evident that by adopting pressure filtration technique it was possible to produce filtered slime, whereas filtration, rate reduces significantly with the presence of finer fraction. Further , the greatest advantage of paste thickening is volume reduction of slime. By considering the technology limitation and comparative lab test work result, it is opined that combination of filtration and paste thickening technology is favorable in terms of capital and operating cost and slime >45 µ should be filtered and < 45 µ slime should go for paste thickening. The study and the results are presented in details.INTRODUCTION The beneficiation processes always end up with an enriched portion of desired mineral - “Concentrate” and an enriched portion of undesired minerals - “Tailing”. The proportion and nature of tailings generated in every beneficiation process differ from ore to ore and reflects the characteristics of the feed processed. The traditional method of tailing disposal in many mineral processing industries has been to dispose them as thickener underflow at around 35% solids. Though, it had certain advantages of transportation with ease but contribute to a greater volume occupied in the tailing dam. This sustained practice and failure to utilize the space available in the tailing dam judiciously endangered the mining industry. The tailing management has become the toughest task to the mining industry and most of the mines are running out of space for disposing the fresh tailings as many of these are at the verge of getting filled."

Jan 1, 2018

By A. Vidyadhar

Printed circuit boards (PCBs) constitute a majorpart of electrical and electronic equipment containing valuable metals such as Cu, Ni, Au, Ag, Pd, Fe, Sn, Pb, etc. The concentration of base and precious metals in PCBs is observed to be several times more than those in their respective ores. Therefore, the recycling of PCBs is necessary to recover the valuable materials. However, the ultrafine particles pose a big challenge. Removal of them is suggested prior to processing by flotation. Froth flotation is observed to be a promising technique for rejecting the plastics from the comminution product. In the present work, enrichment of ground 1.0 mm PCB powder was investigated through flotation route by varying the operating variables such as frother dosage, pulp density, air flow rate and rotational speed of the impeller. The liberation studies indicate that excellent liberation of metal values is achieved from the non-metallic constituents at -1.0 mm size and below. The particulate system is quite rich in metal value with about 23% total metal content. The non-metallic constituents such as plastics are observed to possess strong hydrophobicity while the metal particles in the pulverized mass are hydrophilic in nature. Froth flotation kinetics is studied in depth with a view to facilitate high rejection of plastics and identify optimum operating conditions for the same. A number of experiments are performed to establish the influence of the operating variables on flotation performance. The conditions for achieving higher yield of the metal-rich fraction with respect to a specified grade are discussed in the light of the experimental results. It is found that the requirement of reagents is negligible which could be a very important factor from the commercial stand point. Single-stage flotation increases the metal content from 23% to over 32% with a mass yield of around 75% and over 90% recovery of metal values. 32% of the materials in the feed could be effectively rejected in the float fraction losing less than 4% metal values. The dependence of kinetics on the process variables is also discussed. It was concluded that a high rotor speed helps in efficiently rejecting the plastics. Frother should be added to help stabilize the froth and enhance the kinetics. A moderate air flow is required while pulp density must be kept low for efficient pre-concentration. It is established that the entire -1.0 mm comminution product could be treated by flotation for generating a pre-concentrate. Keywords: printed circuit boards, recycling, froth flotation, kinetics, recovery

Sep 1, 2012

By A. V. Myaskov, V. S. Valavin, K. D’Elia, I. O. Krylov, Vu Van Toan, T. I. Yushina

"The purpose of this research is the development of a technology for processing the concentration tailings of limonite ores at Kamysh-Burun Mining and Processing Complex into an iron- containing product for ROMELT process. In the concentration and metallurgical processing of iron ores, substantial amounts of waste are generated (tailings, slimes, slags, metallurgical dust, etc.) that can be converted into a commercial product if is properly processed. This article presents the results of experimental studies of the feasibility of processing iron- containing tailings of Kamysh-Burun deposit (slimes from Verkhne-Churbash storage facility (VCh sample) and dumped waste of Kamysh-Burun (KB sample)) to obtaining valuable components for further uses. Applying Mossbauer spectroscopy has been shown that the iron minerals in the studied samples are technogenic varieties of iron hydroxides. The most suitable technology is the magnetic roasting process, since iron hydroxides are easily transformed into a magnetic, easily recoverable form. Have been shown the advantages of a two-stage magnetic separation, in a strong field and with polygradient separators. Concentrating this material through magnetic methods makes it possible to increase the iron content to 20-21 %. Magnetic concentration of the deeper layers materials results in iron- containing concentrates with a total iron content of up to 58% whit a phosphorus content of about 2%. Reducing the phosphorus content is possible by blending upper and lower layers of the material at a ratio of 1:1. Thus, it is possible to process the material accumulated in the slime storage facility using the ROMELT process combined with preliminary three-stage magnetic concentration and disposal of tailings with the permissible iron content of less than 5%. Wastes from smelting will be slags suitable for use in construction industry. The Kamysh-Burun material preparation for ROMELT process should be performed applying gravity-washing with separation of the -0.4 mm fraction and additional blending for dephosphorizing the concentrate. The smelting will produce pig iron and slag."

Jan 1, 2018