Search Documents

By P. Braga, A. Chaves, S. França, A. Luz

"In Brazil, there are no official reserves of molybdenum, and the unofficial reserves are modest. Therefore, the molybdenum ore (molybdenite) produced as a co-product or by-product of emerald mining in the region of Campo Formoso, BA, has arisen as the only economic option. The flotation process is commonly used in Brazil for the recovery of molybdenite from emerald mining tailings, but it produces low-content molybdenite concentrates, thereby resulting in a product with low economic value. The molybdenite concentrate produced in Campo Formoso contains 83.5% MoS2 (50% Mo), which is less than the international standard product that contains > 90% MoS2 (54% Mo).This low value is due to the presence of talc, which is a naturally hydrophobic mineral that is also floated with the molybdenite during the flotation process. Separability studies were done in a Partridge-Smith cell using dextrin and quebracho as a molybdenite depressor in solution at different concentrations and pH values to produce a technical-grade concentrate (i.e., 90% MoS2). These basic studies were accompanied by measurements of the zeta potential and contact angle, which was determined by the capillary rise method. The results of these floatability studies were used in bench flotation tests, which were performed in a Denver laboratory flotation cell. A molybdenite concentrate of 93.4% MoS2 was obtained when dextrin was used at a concentration of 100 g/t."

Jan 1, 2014

By Yuhua Wang, Huilan Yang, Yanqing Jiang, Dongfang Lu

"Generally, the concentration of bauxite flotation tailings is around 10%, a large amount of water in tailings needed to be recycled in the flotation process. Sedimentation and dewatering properties of tailings were investigated under different conditions. Surface high negative charges on mineral particles are the key factor to destroy the settlement of tailings when the pulp pH is around 8.9. Hence, the modification of pulp pH around 7 is necessary to the diminution of the repulsive force between mineral particles and then the acceleration of sedimentation of tailings. Anionic polyacrylamine with molecular weight of 14 million is the best flocculant for the settlement of tailings in all tested polyacrylamines. P-toluene sulfonic acid shows better properties than hydrochloric acid for pulp pH adjustment when anionic polyacrylamine with molecular weight of 14 million is used as flocculant. Although the flotation of diaspore is depressed in the presence of polyacrylamine using sodium oleate as collector, but the recycling water traded by the combination of ployacrylamine and p-touenesulfonic acid does not show the depression effects on the flotation of bauxite ore. The lower residual content of polyacrylamine in recycling water treated by the combination of ployacrylamine and p-touene sulfonic acid plays an important role. INTRODUCTION Generally, the waste water generated from mineral processing plant is usually treated by sedimentation, oxidization, electrodialysis, ions exchange, active carbon adsorption and flotation technology, and the treated water is also used again in the industrial process. Flotation was adopted widely to improve the quality of bauxite from low grade diasporic bauxite in China. For flotation, the grinding fineness of bauxite is over 90% -0.074 mm, sodium carbonate and sodium hexametaphosphate were used as regulators, so the tailings pulp is very difficult to settle and be dewatered (Y. Wang et al., 2004; Y. H. Wang et al., 2007; Wang Yu-hua et al., 2008; Wang Yuhua et al., 2011). The water recycling of bauxite tailings are becoming the highlight for the industrial application of the flotation process for bauxite ore. Researchers in China shift their attentions onto this topic."

Jan 1, 2018

By Dmitriy Makarov

The paper presents the modeling and analysis of oxidation of pyrite copper-zinc ore samples from the Letnee, Yaman-Kasy and Valentorskoye deposits. It is found, that the oxidized samples contain copper and zinc sulfates that are leached under the sample and water contact. It is shown, that sulfide floatability is decreased by the longer-term oxidation.We advise to improve nonferrous metals recovery by joint leaching and ultrasonic treatment of oxidized compounds. Study of the geotechnological processes of non-ferrous metal extraction, on the basis of two copper-zinc ore deposits shows, that heap leaching is of little use for the ores of the Letnee deposit. Leaching results for the Yaman-Kasy ore showed more promise.

Sep 1, 2012

Froth flotation is an industrial process commonly used for the separation of mineral particles. Bubbles sparged in a pulp collect and carry hydrophobic particles to the top layer of a flotation cell, the froth zone. There is a strong correlation between the stability of the froth phase and the flux of solids. However, flotation units placed in series operate, as a whole, in a non-steady state regime with the concentration of particle decreasing from one cell to the next resulting in a decrease in froth stability, which can compromise the recovery of valuables. Organic chemical reagents, frothers, are generally added to prevent fine bubbles from coalescing and to increase the stability of the froth phase. Frothers represent the second largest group of mining chemicals. It is crucial to understand the resulting properties of the frother on the froth phase in order to select the most suitable reagent for a particular operation. The bubble coalescence dynamic of three different surfactants, 1-pentanol, poly (propylene glycol), and tri (propylene glycol) methyl ether, were investigated in this study. In the first stage, the stabilisation mechanism of bubbles in a solution of surfactant was investigated using a specifically designed experimental setup. The coalescence behaviour of bubble pairs was recorded using high-speed video imaging in which information such as the coalescence time and the deformation of the resultant bubble upon coalescence could be extracted. The results were then compared between the different surfactants for several concentrations. It is shown in a study that the coalescence time increases with surfactant concentration until the Gibbs-Marangoni effect is suppressed by bulk diffusion. Conversely, the oscillation of the resultant bubble was found to be affected only at concentrations at which the film is saturated. The implications of the effects of surfactant type and concentration on the coalescence time and bubble oscillation in froth flotation are discussed. Keywords: froth flotation, frother, bubble coalescence

Sep 1, 2012

By G. Alfano

We have investigated the breakage actions of solid particles observed in a new generation fluid energy micronizer being set up at our laboratories. The attention has been focussed in particular on breakage caused by interparticle collision, particle impact against a fixed surface, interparticle attrition and particle against wall of jet mill attrition. We have also studied the influence of grain size distribution, maximum particle size, flow rate and characteristics of the solid to be processed, as well as of flow rate and pressure of injected air on the above mechanism. Lastly, the operating parameters of a dynamic air classifier in closed circuit with the micronizer for recovering the fine fraction and automatically recycling the oversize, have been optimized. The findings of this investigation have been used to design, build and fine tune a micronizer capable of controlling the top size of a product having average particle size that meets market requirements for fine powders, while keeping power consumption relatively low.

Jan 1, 2014

By H. Kasaini

Batch wise adsorption tests for platinum (Pt) on the surface of activated carbon pellets (Norit RO 0.8 BET surface area 1100 mg/g) were carried out in mixed chloride solution. The purpose of this study was to assess and compare the adsorption performance of amine-treated activated carbons (AACs) and native activated carbons (NACs) in terms of adsorption capacity and selectivity. The effect of pH and temperature on adsorption capacity and selectivity was established. The amine- treated ACs were prepared by anchoring the amino groups (butyl amines) on the surface of AC pellets in aqueous media and the UV-Vis was used to determine the amount of amine sequestered from solution by ACs. The dosage of butyl amine on the surface of ACs averaged 0.15 g/g, carbon. The adsorption mechanism was described by the ionization and complexation model whereby interaction between the protonated AAC surface and the anionic chlorocomplex ions (PtCl5 [H2O]-, PtCl62-) proceeded by either electrostatic attraction or/and by covalent bonding [(NH3)2PtCl6 or (CH2COO)2PtCl6]. By comparison, the adsorption capacities of Pt on amine-treated ACs and native ACs were 53.8 mg/g and 33.03 mg/g, respectively which highlight the benefits of anchoring functional molecules on ACs. The selectivity of AACs was influenced by solution pH. Pt adsorbed selectively on the surface of amine-treated ACs at pH<1.5. The highest separation factor that was recoded pertained to Pt and Fe species (ßPt/Fe = 90) then followed by Pt and Ni species (ßPt/Ni = 30) or Pt and Cu species (ßPt/Cu = 15). The lowest separation factor was recorded for Pt and Cr ions (ßPt/N= 5). Adsorption kinetics of Pt on amine-treated AC surfaces, according to the first and second order reactions, were investigated and results showed that rates were in the order 10= 5). -4 min-1 and 102 g?min/mg, respectively. The pseudo 1st order kinetics predicted the adsorption capacity of 51.81 mg/g which was almost similar to the experimental value (53.8 mg/g) while the second order rate equation predicted Pt adsorption capacity of 40.1 mg/g. Both The Langmuir and Toth isotherm fitted the Pt adsorption at pH < 1.0. The Freundlich isotherm tended to underestimate the adsorption capacity of AACs.

Jan 1, 2014

By Zhou Junwu, Han Long, Song Zhenguo, Sun Chuanyao

The deposit genesis, the ore property, and the mineral characteristics, which has a close relationship with the beneficiablity, could be regarded as the “Genetic Properties”, actually are the determining factors for beneficiation process development. However, in conventional concentrator’s process development and engineering, there have been lack of systematic research and test on those genetic properties, also lack of well-established collecting, statistics and analysis system for those huge amount of data such as the historical mineral processing technique research, process mineralogy study, practical operating and engineering data. Obviously it is far less than enough for profound integration combining modern IT together with traditional mineral processing technology, as a result there are a number of disadvantages in mineral processing R&D and engineering, such as long term, high cost, low efficiency as well as repetitive testwork not making full advantage of previous experiences. Aiming to make utmost of those Genetic Properties and overcome above disadvantages in mineral processing R&D and engineering, the concept of “Genetic Mineral Processing Engineering (GMPE)” is put forwarded, and the strategical study has been conducted on this regard, with the main focus on following aspects: a) Testing and extraction of the “Genetic Properties”; b) Establishment of data base and data warehouse of GMPE; c) Intelligent decision making system for beneficiation process; d) Verification testwork; e) Virtual concentrator. The technical route proposed is to firstly conduct research and test on those Genetic Properties mentioned above, based on that the specific data base will be set up and applied for intelligent process recommendation and simulation with a few verification testwork conducted in the meantime, finally achieve a fast, high efficiency and precise determination of technology and process for ore beneficiation. The systematic study on the three-in-one GMPE would make an innovative breakthrough in conventional mineral process testwork research and engineering methodology, and provide technical support for the concentrator’s design and upgrading.

Jan 1, 2018

By M. I. Panayotova

Some of effluents released by copper smelting plants are highly acidic (pH = 0~1) and contain arsenic and copper in relatively high concentrations (10~20 g/L). Usually arsenic is removed by precipitation with different reagents, such as lime, iron salts, calcium salts, aluminium salts, etc. Precipitates (often voluminous) that require further handling are formed and copper and other valuable components are lost. A method is presented for copper and arsenic extraction from acidic effluents. Effluents are treated in specially designed closed electrochemical cell without chemicals? addition. Gases formed are collected and treated for decomposing the eventual traces of As-bearing compounds and ensuring the environment protection. Initially copper of grade of 85 % is electro-won. Further about half of the initially available arsenic is separated as low-soluble, low volume mixture of intermetallic compounds, oxides and some elemental arsenic. At the next stage the main part of the left arsenic is immobilized as low soluble stable compound. Arsenic content in the treated acid is in the range 0.20~0.25 g/L. Acidity of treated effluent after first two stages remains practically unchanged and the solution can be re-used. Physicochemical and electrochemical processes, governing copper and arsenic removal, are discussed.

Jan 1, 2014

This paper presents a theoretical investigation on the ionic equilibrium of Fe(III)?Ni(II)?H2SO4?H2O system. A non-ideal speciation model is developed to calculate the concentration distribution of iron and nickel species in a mixed ferric and nickel sulphate aqueous solution over the pH range from 0 to 4 and temperature from 25 to 100°C. A series of speciation diagrams for iron and nickel species is plotted with the effects of ionic strength and temperature on the equilibrium constants being taken into account. The ionic strength-dependent equilibrium constant is treated through a semi-empirical Vasil&apos;eV equation, which is based on an extended Debye?Hückel theory. A Helgeson model is applied to extrapolate the equilibrium constant to elevated temperature. The ionic equilibrium reactions are described by a group of numerical equations containing the temperature and ionic strength-dependent equilibrium constants, which are solved by the Newton-Raphson method. The speciation model is also applied to estimate the hydrogen ion activities and corresponding pH values. The calculated pH values are in agreement with the experimentally measured pH, and are compared to literature data and pH values produced by the Visual MINTEQ® program (a computer code for the calculation of chemical equilibrium in natural aqueous system). This investigation provides a deep insight into the ionic equilibrium behavior of a mixed metal sulphate aqueous system which commonly occurs in hydrometallurgical processing. Keywords: speciation, chemical modelling, thermodynamics, iron, nickel

Sep 1, 2012

By Moris Fresko, Julia Sun, Charles C. Golembewski, Vytas Svalbonas

"A history of mill strain gaging at Metso is presented. The output of these strain-gaging programs is compared with calculated stress ranges from different finite element solutions. These comparisons expose the amount of approximation that exists in the analytical solutions, starting from geometry, and material properties, and ending with different forms of internal load models. The influence of strain gaging results on mill design and analysis practices is also discussed. While these instrumentation programs are valuable in identifying areas of high stress in mills, and locations of stress concentration factors, they are by no means extensive or comprehensive enough to verify general internal load models. The vast majority of the programs were aimed at getting additional data about potential failure points, rather than describing overall mill stress behavior. This is especially true since the more recent gaging programs have not included the difficult task of gaging the mill rotating structure interior. This paper tries to avoid the novice path of leaping to general conclusions on the basis of insufficient data."

Jan 1, 2014

By Saeed Farrokhpay

It is known that the grinding condition has a major effect on the beneficiation characteristics of the minerals in subsequent processing, in particular, flotation. In the flotation process, particles surface and their condition can significantly influence collector adsorption and flotation performance. For example, particle shape and its surface roughness occurred during grinding may influence flotation characteristics of a specific ore. In fact, adsorption of different cationic and anionic species on mineral surfaces can be varied depending on the selected comminution procedure. The flotation performance of sulphide minerals can be detrimentally affected by the surface oxidation. The amount of surface oxidation may reduce the hydrophobicity of the mineral and makes adsorption of collectors less selective. Improved liberation may generally result in improved flotation recovery. However, this may result in finer grinding and slimes, and consequently, reduce the overall flotation recovery. This paper discusses the effect of wet and dry grinding on copper flotation of a complex Cu-Pb-Zn ore. Industrially, wet grinding is preferred due to its higher energy efficiency and owing to downstream processing requirements. In this study, series of flotation tests were conducted,and surface analysis (XPS and ToFSIMS) were performed after wet or dry grinding at two different P80 values. Mineralogical study was also conducted to investigate the liberation of valuable minerals after grinding. A higher copper flotation recovery was found for wet grinding. However, the copper recovery was increased by further grinding in both conditions (wet and dry). The results showed a higher collector adsorption on copper mineral surfaces after wet grinding. The surface analysis also revealed that the ore is slightly more oxidized after dry grinding probably due to higher temperature during dry grinding.

Sep 1, 2012

By Gurubasayya Swamy

This paper presents the consequences of modernization and expansion of process plant by implementing SAG and Ball Mill and Carbon-in-pulp technology at the Hutti Gold Mine. From the inception of the process plant, it has undergone many changes for the improvement. In the beginning, only gravity recovery of gold was carried out by using Pebble Mills and Strake Tables. Later amalgamation, Cyanidation and Zinc precipitation and finally Carbon-in-pulp gold recovery system was implemented. Grinding plant was modernized by implementing SAG and Ball Mill and Knelson concentrator for free gold recovery as a result, the production rate, rate of recovery, reduced man power, Modernization and expansion of process plant has also yielded in safe and smooth running of the plant. Keywords: sag and ball mill, cip, modernization and expansion, productivity, gold recovery

Sep 1, 2012

By M. Paymardi, A. Foroutan, T. P. Oladele, M. Abbaszadeh

"Reducing the amount of zinc and iron in lead concentrate is one of the important aspects of processing in lead and zinc flotation plants which results in improvement of lead concentrate quality and prevents zinc loss. In mineral flotation industries, lignin sulfonates are known for their depressant properties for both non-metallic and sulfide minerals such as pyrite and pyrrhotite.This paper investigates the effect of lignin sulfonate on flotation of galena, sphalerite and pyrite in sulfidic lead and zinc bearing ores. Batch flotation tests were carried out on a high pre-activated zinc samples. The feed contains 0.9% lead, 2.3% zinc and 7.5% iron. The dosage of all reagents such as sodium cyanide, zinc sulfate, ethyl xanthate and methyl isobutyl carbinol (MIBC) were kept constant for lead flotation step except calcium lignin sulfonate (CLS) that was varied between 0 and 80 gr/ton.Results for lead rougher concentrate showed that the grade of lead increased by 2.7% while the recovery decreased around 4 % at the highest dosage of CLS. Furthermore, zinc recovery decreased by 6.3% with no significant change in grade. Iron recovery in lead rougher concentrate decreased by 2.3 % while the grade changed around 1%. In sphalerite flotation step, CLS dosage was changed in the range of 0 to 80 gr/ton while the dosage of other reagents such as copper sulfate, lime, amil xanthate and MIBC were kept constant. In this step, no decreasing in grade and recovery of zinc was observed, while iron recovery decreased. It was suggested that CLS has a depression effect on sphalerite in conjunction with other zinc depressants such as zinc sulfate and sodium cyanide. CLS was further used in plant with non-pre-activated zinc minerals. Similar trends were observed in plant.INTRODUCTIONlead-zinc sulfide minerals play an important role in the production of lead and zinc metals in the mineral processing industry (Luo, Feng et al. 2016). Due to complexity of the lead-zinc ores mineralogy, in some situations, their flotation properties vary significantly from one deposit to another one even in itself (Bulatovic 2007)."

Jan 1, 2018

By Kwang Soon Moon

Liquid ? liquid reactions such as solvent extraction in hydrometallurgy and BTX extraction in petrochemical industry has long suffered from the long retention time mainly due to the limited interfacial area caused by the immiscibility between water and oil phase, requiring typically very large perfect mixer type reactors and tall adsorption towers. A novel spray reactor for immiscible liquids; that is the KISEI Nozzle Reactor (KNR) was introduced, enabling the drastic increase in the interfacial area between the reacting immiscible liquids. Various spray mechanisms were applied in materials processing, e.g. spray drying, powder metallurgy, and aerosol industry, but not in hydrometallurgy. The KISEI Nozzle Reactor(KNR) was fully developed and used in production of biodiesel from the immiscible triglycerides and methanol. An experience with a full production plant facility is briefly discussed in the current paper. With the fog-like methanol spray in oil medium, the trans esterification reaction was almost instantaneous, and transformed the traditional batch trans esterification process into a continuous production process. And above all, with no moving parts in the KISEI Nozzle Reactor (KNR), the process requires minimal operation and maintenance costs. Keywords: immiscible liquids reaction, nozzle spray reactor, continuous biodiesel reactor, hydrometallurgy, organic extraction, micro emulsion

Sep 1, 2012

By A. I. Arol

Bentonite is an important industrial mineral with very wide application areas. Its unique colloidal, swelling, thickening and adsorption properties make it a useful agent in drilling, metal casting, and iron ore pelletizing, environmental, food, cosmetics, pharmaceuticals and many more industries. Because of its swelling property, bentonite suspensions can only be prepared at rather low solid coentrations, i.e. 8-10%. In order to process bentonite in slurries with high solid content, it was thought that a non-polar organic solvent, instead of water, can be used. Not only large amounts of bentonite can be dispersed in organic solvents but also the solvents may be regenerated. The bentonite obtained through such a process must either equal or better properties than those of untreated bentonite. In this study, the effect of organic solvents such as acetone, methyl-ethyl ketone and n-haxane on the main properties of bentonite, such as water adsorption and rheology, was investigated. It was found that bentonite can be dispersed in the mentioned organics in large quantities with no loss of quality. Keywords: bentonite, montmorillonite, water adsorption, industrial minerals

Sep 1, 2012

By G. S. Zeng

The mechanism of cobalt removal from zinc sulfate solution with zinc dust is still not understood well. The experiments in this paper were carried out by zinc dust from zinc sulfate solution with high cobalt to study the mechanism of cobalt removal. Residues after the cementation process from zinc sulfate solution were analyzed by SEM and Electron probe micro-analysis (EPMA) to investigate the morphology of products. Different temperature will cause different structure of particles. With the increasement of temperature, cobalt removal can be improved considerably. The mechanism of cobalt removal by zinc dust is thought as follows: firstly, the cobalt ion forms Co-Zn alloy with zinc particles, and the reaction reaches equilibrium quickly; secondly, the Co-Zn alloy continues reacting to Co with Co2+, which is the control procedure of the whole reaction.

Jan 1, 2014

By A. Muhammad, A. Abdelaal, M. EL Salmawy

"Energy is vital for economic growth and sustainable development. Greater efforts are being devoted to developing unconventional energy resources such as oil shale as an alternative promising source of oil or solid fuel supplement. The main object of this contribution is to determine the upgrade potential of El-Nakheil oil shale using froth flotation. Samples were prepared by comminution followed by sieving into different size fractions. The flotation behavior of the material and extent of cleaning was studied with respect to nonionic and ionic collectors of anionic and cationic types. It was found that the organic rich portions could not be rendered sufficiently hydrophobic by the used collectors and selectivity towards surfactant was very low."

Jan 1, 2014

By D. M. R. Sekhar

Certain types of rock phosphates of sedimentary origin are applied to acidic soils as fertilizer directly. Recent research in India showed that high grade rock phosphate in fine size when used as a mix with organic manure works as efficiently as di-ammonium phosphate (DAP) in alkaline soils. The rock phosphate from Jhamarkotra, India (sedimentary origin), Egypt (sedimentary origin) and South Africa (volcanic origin) showed good agronomic efficiency when used as Phosphate Rich Organic Manure (PROM). Further PROM shows equal residual effect. The results of efficiency of PROM made using two grades (+ 24% P2O5 and 34% P2O5) of rock phosphate mineral from Jordan show that low grade rock phosphate slimes are as effective as high grade phosphate concentrate when used in PROM. Also PROM is very effective in the saline soil of Eshidiya desert where DAP is not at all effective.

Jan 1, 2014

By D. B. Mazzinghy, D. C. Rocha, H. B. Miller

"The use of ball mills for fine grinding is an inefficient process and has contributed to the increasing popularity of vertical stirred grinding mills in the minerals industry. Over the last decade, the performance and energy efficiency of stirred milling technology has become a preferred alternative to ball mills for fine and regrinding operations. The difficulty encountered in fine grinding is the increased resistance to comminute small particles when compared to coarse particles. Therefore, increased energy inputs are then necessary to raise the number of stress events in a mill to contribute to the comminution of fine particles. This work discusses the effect of operating conditions on the amount of fines produced and torque readings in a screw type batch laboratory vertical stirred mill. A time-based population balance model (PBM) was used to empirically analyze the performance of a vertical mill and to calculate mill breakage parameters for the different operating conditions tested. The results indicate the possibility of applying population balance model to the vertical stirred mill to predict product size distribution with acceptable accuracy. The obtained breakage function shows that the main breakage mechanism in this vertical stirred mill is by attrition, and that the selection function changes with experimental conditions within the mill. Higher agitator velocities are also seen to promote an increase in the degree of attrition between grinding media hence particle selection and fines generation increase.INTRODUCTION Stirred milling technology has been firmly established in the last 20 years as superior to ball mills for fine and regrinding operations due to its superior energy efficiency (Jankovic, et al., 2006). Stirred mills are now commonly used in many sectors of the mining industry, though they have been used in other industries for many years (Stehr & Schwedes, 1983). This technology has proven to be more energy efficient with greater opportunities for future optimization in both fine and coarse grinding."

Jan 1, 2018

By P. Thareja, V. Prasad, S. P. Mehrotra

In recent times, the transportation of minerals and their tailings has become a major concern across the world. There exists a huge demand of efficient and cost effective transportation system which poses minimum environmental damage. One of the economically and environmentally viable techniques which potentially offer a solution to the above problem includes transportation of minerals and their tailings in the slurry form through pipelines. Slurry transportation through pipelines is reported to be more beneficial in terms of cost, environmental impact, maintenance and safety when compared with other conventional modes of bulk transportation such as train, truck, barge and conveyors. The main challange associated with hydraulic transportation of slurries is to obtain a non-settled slurry and to design a pipeline system which results in the optimum energy requirement for transporting a large throughput to longer distances at a lower cost. The feasibility of hydraulic transportation of slurries through pipes mainly depends upon slurry properties and flow conditions in the pipe. Results from rheological studies exhibit the presence of shear thinning flow behaviour of minerals and their tailings in water. The flow behaviour index (n) and consistency coefficient (k) obtained from the rheological analysis are further used for the specific energy consumption and energy losses during transportation. The cost of transportation in USD per ton per 100 km and transport capacity in tons per day are calculated from the specific energy consumption to transport these slurries. The results demonstrate that the slurries can be transported to long distances (say, 100 km or more) corresponding to optimum energy consumption and dissipation rate at a substantially cheaper cost than the existing rail and road transport in India. Although we have carried out transportation studies with coal fly ash (CFA), lignite & bauxite slurries, for paucity of space, the results reported here are essentially for CFA slurries. Details of our investigations with lignite coal & bauxite will be reported seperately.

Jan 1, 2018