Search Documents

By M. Alvarez-Silva

The control of the amount of chromite reporting to the concentrate during the flotation of UG2 ore is of critical importance since its presence affects the downstream smelting process. It is generally reported that the main mechanism responsible for chromite recovery is through entrainment. This is reflected in analyzing the solids and water recoveries. These in turn are strongly dependent on the froth phase. In the present investigation a laboratory scale column flotation cell was used to investigate the role of the froth phase in the flotation of UG2 ore. Such a device is superior to a standard batch cell since it operates at steady state in open circuit and also allows for a greater degree of flexibility in terms of froth heights. The mass of solids and water recovered in the concentrate as well as chromite (Cr2O3) recovery by size class was determined as a function of froth height, superficial gas velocity and depressant dosage. The results showed that depressants had little effect on chromite recovery but increased the grade due to the depression of gangue minerals. A 60cm froth height always resulted in slightly lower solids, water and chromite recovery than for 30cm. Typically only 20-25 % of solids reaching the pulp-froth interface reached the launder. The relationship between solids and water recovery for a wide range of conditions indicated that chromite is mostly recovered by entrainment. Keywords: UG2 ore, column flotation cell

Sep 1, 2012

By Sarthak Kaushik

Zeta potential measurements show that the isoelectric point of crandallite, in aqueous solution of 10-2 N sodium chloride is at about pH 5.5. Measurements of turbidity confirm the point of zero charge or crandallite. Calcium ions specifically adsorbed on the surface and thus changed the zeta potential and turbidity. From the measured data, it is confirmed that starch acts as a flocculent for crandallite. Oleic acid, which is a collector used in phosphate ore processing is weakly adsorbed on the surface of crandallite. This results in hydrophobic coagulation of particles resulting in a lower turbidity.

Sep 1, 2012

By Hamid-Reza Manouchehri

"Sustainability calls for maintenance, rational use and enhancement of natural resources as well as balance consideration of ecology, economy, and social justice. The challenges in mining industry call for a sustained global effort using the leverage of available technologies and emerging new technologies. The industry uses significant amount of energy with the highest portion in comminution. To conserve energy, attempts have been made to improve the efficiency of the conventional crushing and grinding equipment. Nevertheless, the new and energy efficient comminution technologies are favorable through a longer term strategy. Since crushers are more energy efficient than mills, it is logic to conduct part of milling, in the crushing stage. After years of research and development, Sandvik introduces a new crushing technology, VibroconeTM, to change traditional crushing concepts. The new crushing device is able to crush and grind particles with a higher reduction ratio, more than two fold, than that of conventional crushers. By implementation of the new technology, a suitable feed size for milling can be provided to conserve energy as well as media and liner consumption, to reduce milling circulating load or increase mill capacity. There are other benefits associated with this machine, one of them being providing a higher surface area. This paper discusses the performance of the machine and its applications for comminuting different ores."

Jan 1, 2014

By Andries Van Wyk, Steven Bradshaw, Guven Akdogan, Jacques Eksteen, Cornelius Snyders, Cleophace Mpinga

"In order to exploit lower grade and complex platinum group metal resources, cheaper and more efficient alternatives to the conventional mill-float-smelt-refine route are being sought, particularly for resources’ in areas that are water-scarce and where electrification is costly and problematic. Leaching with cyanide is a promising process option and although recoveries are lower than in the conventional process routes, progress into the understanding of cyanide leaching of PGM containing ore and concentrate has been made. Research regarding the feasibility of upgrading the pregnant PGM leach solution using activated carbon has, however, been lacking and hence forms the focus of this paper. Bottle roll adsorption tests for dilute PGM solutions (0.15ppm Pt, 0.38 ppm Pd, 0.1 ppm Au) onto granular activated carbon showed high rates within the first 60 minutes (giving more than 90% recovery of precious metals). Comparison of the Pt isotherm to Au isotherms from literature indicated a similar loading capacity, while that of Pd was found to be significantly lower. The effects of solution pH, temperature, base metal concentration, free cyanide concentration, thiocyanate concentration, initial PGM concentration and activated carbon concentration were investigated and are discussed. Elution of the Pt and Pd, with the AARL elution process, was found to be effective with recoveries of 95% after 5 bed volumes of eluant at the optimum pre-treatment concentrations and a temperature of 80°C. Temperature, NaCN and NaOH pre-treatment concentration and the ionic strength of the eluant were found to be the most important factors affecting elution while base metals concentration, acid-pre-treatment, carbon loading and thiocyanate concentrations to a lesser extent. Simplified combined flow sheets are suggested and the corresponding mass balances are compared."

Jan 1, 2014

By D. J. Zhao

The reduction and nitridation of preoxidized ilmenite pellets were investigated with the prospect of creating grain refiners containing titanium oxides and titanium nitride dispersoids. All the reduction and nitridation reactions were conducted in a furnace with a thermogravimetric analysis system under a H2-N2 gas mixture of 5 L/min. The ilmenite pellets were reduced at 1100°C for 4 hours under 80%H2-20%N2 gas mixture, and then respectively nitrided at 700°C, 800°C, 900°C and 1000°C for 12 hours under 10%H2-90%N2 gas mixture. The products were characterized by X-ray diffraction (XRD) and Scanning Electron Microscopy (SEM), and analyzed by Energy Dispersive Spectrometers (EDS) and Electron Probe Mapping Analysis (EPMA). Iron oxides were reduced into metallic iron, and oxides of titanium were found, but titanium nitride particles were not identified in the products under the prevailing conditions.

Jan 1, 2014

By P. Huang

Chitosan was tested as a depressant in the differential flotation separation of chalcopyrite and galena. The micro-flotation results showed that chitosan selectively depressed chalcopyrite while galena was floated by potassium ethyl xanthate in acidic solutions. With the addition of 0.67 mg/L chitosan (CT) in the slurry of chalcopyrite-galena mixtures at pH 4, the recovery of galena was 95% while that of chalcopyrite was 30%, indicating that chitosan could potentially be used in differential Cu-Pb sulfide separation. Furthermore, the study of chitosan with either low (LCT) or high molecular weight (HCT) in the differential flotation indicated that better separation was achieved by the chitosan with lower molecular weight (LCT). ToF-SIMS was employed to study the distribution of CT on the surface of chalcopyrite-galena mixtures by ion mass spectra analysis and surface imaging, which showed that CT adsorbed heavily on chalcopyrite but barely adsorbed on galena. The positive ion ToF-SIMS spectra provided information on the surface composition of chalcopyrite-galena mixtures after CT treatment. It appears that the selective adsorption of CT on chalcopyrite was originated from the strong interaction between NH3+ and Cu. Keywords: differential flotation, micro-flotation

Sep 1, 2012

By D. W. Fuerstenau

Understanding how cationic surfactants affect the interfacial behavior of quartz is important in mineral processing and environmental engineering. This paper presents the results of a study of the effect of the molecular structure of cationic surfactants on the interfacial behavior of finely ground natural quartz. Most of the experimental work involved the determination of zeta potentials and the stability of quartz suspensions. Some measurements of induction times and the flotation response of coarser particles are also included. How these surfactants affect interfacial behavior is discussed in terms of adsorption mechanisms. The molecular structure (number of hydrocarbon chains, type of ionic head group, number of ionic head groups on the molecule) of these reagents was found to significantly affect their surface activity.

Jan 1, 2014

By Regis Texeira, Leopoldo Gutierrez, Vicente Hernandez, Caludia Vidal, Lina Uribe

"Molybdenum is currently the most important by-product of Chile´s copper mining industry. This mineral has gained international relevance over the years, because of its price. At mining deposits in Chile, copper and molybdenum are extracted together and then separated in a concentration process consisting of several flotation steps using sodium hydrosulfide (NaHS) as copper depressant. However, there are environmental issues related to the potential emisions of toxic hydrosulfide gas and bad odours, which affects nearby communities and suppose a risk for operators. This problem has led to the need for development of new technologies to eliminate the use of NaHS in the process of selective flotation of Cu and Mo minerals. In this work, results of flotation tests in which lignin derivatives reagents are used to obtain the selective separation of Cu and Mo minerals by flotation are presented. In this technology molybdenite is depressed by the action of lignin derivatives (lignosulfonates), while copper sulfides remain hydrophobic and float. The use of lignin derivatives in the selective flotation of copper molybdenum minerals represents a non-toxic alternative to NaHS.INTRODUCTIONSeparation of copper sulfides from molybdenite is commonly achieved through a two-stage flotation process. In the first stage the collective flotation of copper sulfides and molybdenite is promoted to generate a collective concentrate which is then treated in a second stage with sodium hydrosulfide (2.5-3.0 kg/t NaSH) to depress copper sulfides flotation without affecting the flotation of molybdenite. As a result a copper concentrate with 30-35% Cu, and a molybdenum concentrate with 50-52% Mo are generated. Although this process is widely used at industrial level, environmental issues related to the risk of H2S generation and bad odors have always been a concern. Thus there is a need in the industry for a more environmentally friendly process to separate copper sulfides and molybdenite."

Jan 1, 2018

By Gus Van Weert, Samuel A. Bolorunduro, David B. Dreisingerm

"As deposits of high-grade base metal sulphides become depleted, attention must be focused on the treatment of complex sulphides, which contain significant fractions of precious metals such as gold and silver. Acid pressure oxidation is a promising process for these materials and the recovery of silver and gold will improve the economy of the process. Gold can be recovered from the oxidised residues, however, silver is incorporated into the jarosite specie and the cyanidation of the resulting residue yields very low recovery.Pressure oxidation of various complex sulphides was carried out at 110-150°C in sulphate media with additions of potassium iodide under conditions similar to industrial autoclaving. The resulting residues were subjected to cyanidation. High recovery of silver, up to 98%, was achieved because its incorporation into lead-hydronium jarosite during the pressure oxidation was minimised, while its deportment into the cyanide-soluble silver iodide was favoured. Silver recovery decreased slightly at high temperatures (140° and 150°C) because of the enhanced stability and kinetics of lead-hydronium jarosite, but this could be overcome by increasing acidity and iodide concentration of the autoclave slurry."

Jan 1, 2003

By J. Vilcáez

The copper extraction yield from thermophilic bioleaching of chalcopyrite depends on temperature, pH, and the oxidation-reduction potential (ORP), as well as the activity of the microbe used. We studied copper extraction yields obtained from chalcopyrite with three thermophiles, Acidianus brierleyi, Sulfolobus metallicus, and Metallosphaera sedula, under various pH and temperature conditions and with different initial amounts of ferric iron. The results indicated that the capacity of each thermophile strain to leach iron as Fe3+ differed, which affected the influence of pH, temperature, ORP, and microbial activity level on the yield of copper. Microbial activity can cause ORP to be close to the critical value (450 mV) at which copper extraction at 65 °C can be higher than that at 80°C. An initial pH of 1.5 retards the precipitation of jarosite, allowing temperatures as high as 80°C to result in copper extraction yields close to 100%. However, if a thermophile with a poor capacity to form Fe3+ is employed, 100% copper extractions can also be obtained at pH 2.5, because ORP is low as result of low amounts of Fe3+ in solution. Optimum temperatures for the growth of thermophiles did not always mean high copper extraction yields. Conversely, high biomass concentrations depending on the capacity of the thermophile strain to leach iron as Fe3+, can result in excess Fe3+ in solution, leading to the precipitation of large amounts of Fe3+ as jarosite. The bioleaching capacity of A. brierleyi was reduced or suppressed when insufficient initial Fe3+ was pro-vided to trigger the leaching reaction, whereas S. metallicus and M. sedula were less sensitive to the initial availability of Fe3+. This result confirmed that a direct enzymatic attack on the mineral surface could initiate the leaching reaction, but later ORP governed the leaching rate of chalcopyrite.

Jan 1, 2014

By T. B. M. Himawan

In this study, effect of thiosulphate and oxidation using oxygen were studied in arseno copper ore flotation. Single mineral study of chalcopyrite and tennantite in regard to the aforementioned techniques was also studied. Zeta potential, XPS, contact angle and floatability of single minerals were conducted for each treatment to understand the mechanism. It was revealed that the separation is best conducted in alkaline condition at where there will be interaction between thiosulphate and the mineral surface as well as the formation of hydroxide species in the oxidation using oxygen. From zeta potential of both thiosulphate and oxidation conditioning, it can be found that the reactivity of tennantite is much higher rather than chalcopyrite resulting higher rate of depression on both techniques as shown from contact angle and floatability of each mineral after treatment. XPS spectra confirmed qualitatively and quantitatively the existence of species responsible for the depression of each conditioning techniques. As for the copper ore flotation test, it is the oxidation using oxygen provides best performance after 60 minutes of oxidation. Keywords: tennantite, chalcopyrite, arseno copper ore A, thiosulphate, oxidation using oxygen

Sep 1, 2012

By Carlos de F. Gontijo

The flotation of quartz particles was studied over the particle size range from 0.5 µm to 1000 µm and for advancing water contact angles between 0º and 83º. Flotation was performed in a column and in a Rushton turbine cell. Particle contact angle threshold values, below which the particles could not be floated, were identified for the particle size range 0.5~1000 µm, under different hydrodynamic conditions. The flotation response of the particles, either in a column or in a mechanically agitated cell with a similar bubble size, was comparable. Turbulence plays a role, as does bubble-particle aggregate velocity and bubble size. The stability of the bubble-particle aggregate controls the maximum floatable particle size of coarse particles. For fine particles, the flotation limit is dictated by the energy required to rupture the intervening liquid film between the particle and bubble. Flotation of very fine and large particles is facilitated with small bubbles and high contact angles. These results greatly extend our earlier observations and theoretical predictions.

Jan 1, 2014

By Fu Ping-Hao, Sergio Mauricio Vianna, Ewen Silvester, Emmy V. Manlapig

"Over the last 5 years, an ambitious project has been undertaken at the Julius Kruttschnitt Mineral Research Centre (JKMRC) aiming to isolate, study and, if possible, model the effect of particle size, liberation and collector adsorption density on the floatability of mineral particles. As part of this project, we have conducted highly controlled flotation test-work, combined with state-of-the-art solution and surface analytical techniques such as High Performance Liquid Chromatography (HPLC), Time of Flight Secondary Ion Mass Spectroscopy (TOF-SIMS) and detailed mineralogical analysis to fully characterize the flotation behavior of a natural ore.The flotation tests were undertaken using a high-grade lead-zinc ore from BHP-Billiton’s Cannington mine (Australia) in a specially designed continuously operated laboratory scale flotation rig. Solution and adsorbed collector concentrations were measured independently during the course of the flotation tests using HPLC based ex-situ techniques. Liberation studies were performed using the JKMRC Mineral Liberation Analyser (MLA) on selected size intervals of different streams to estimate the specific surface area of galena. These results were used to calculate the collector adsorption density (collector coverage) on galena particles, with the eventual aim of developing a mathematical model describing the relationship between pulp chemistry, feed mineralogy, and floatability of galena particles."

Jan 1, 2003

By H. Pearce, A. E. Lewis, A. Ochieng

"Hydrodynamics and mixing are fundamental to the operation of mineral process systems such as flotation cells and metal precipitation reactors. Hydrodynamic conditions influence phase mixing and mass transfer in a multiphase system, and these affect the overall performance of such a system. Detailed information on the effects of the hydrodynamics on the performance of agitated systems is still required for the design and optimal operation of hydrometallurgical systems, which are always multiphase. Computational fluid dynamics (CFD) techniques have been employed to study the hydrodynamics and mixing, most of which have focussed on the performance of axial and radial pumping impellers in agitated tanks. However, very little has been reported on the influence of a draft tube on the flow profile in such systems.CFD simulation of a stirred vessel centres on the way the impeller is modelled. Some of the most recent approaches to modelling an impeller are impeller boundary condition (IBC), snap shot, sliding grid (SG), multiple frame of reference (MFR) and inner outer (IO). The accuracy, with which these models predict experimental results and the corresponding computational demands, form the basis upon which the choice of an approach is made. Most of these approaches (IO, SG and MFR) address the key problem of the stirred tank modelling, namely, the simultaneous meshing of the rotating impellers and the stationary baffles. The MFR is computationally cheap and has been found to give predictions that compare well with experimental data.The CFD technique (code CFX4.4) has been employed in the present work to study the hydrodynamics in a mixing vessel stirred with either a Rushton turbine or a pitched blade impeller. The multiple frame of reference (MFR) approach has been used to model both impellers. A draft tube was used only in the Rushton turbine stirred vessel. The flow profiles for the impellers have been studied in three regions; below the impeller tip, at the middle of the tank, and near the liquid surface. The simulation results were compared with literature data obtained using a laser Doppler velocimetry in the three regions of the vessel, and it was found that the model predictions were better in the impeller region. There was a poor prediction of the experimental results in the region closer to the liquid surface; however, this was improved when the turbulence parameter (C2) in the k-e model was set to a higher value. The value of the impeller clearance at which the Rushton turbine generates an axial impeller type flow has been determined and it has been shown that, at this clearance, a draft tube can be used to enhance axial flow in a Rushton turbine stirred reactor."

Jan 1, 2003

By Lev O. Filippov, Inna V. Filippova

"Flotation of metal-organic precipitate in column is sensible to the hydrodynamic conditions determined by the diameter and the dispersion of rising bubbles. Thus, the dissipation energy in the system resulting of ratio between superficial fluid velocities (gas and feed) in the column is the main parameter for precipitate flotation in pilot or industrial scales. The suggested limiting factor is the aggregate stability under the turbulence created by the rising bubbles. The stability of precipitate is related to the structural organisation of aggregates, which determines the size distribution of particles during precipitation and flotation stages.Structural evolution of Mo precipitate and the destruction phenomenon were described by using of the various fractal dimensions. The fractal studies allow the detection of a structural scaled organisation of the precipitate flocs. The fractal dimension of the particle mass distribution Dm=1.94+/-0.15 suggests, for the floc structure, a cluster-cluster aggregation process either with restructuring or breakage phases.The destruction process, which occurs for the lowest values of the dissipation energy E (0.02 . 0.05 W/kg) was characterised by a fractal dimension Dg of size distribution. Besides, the destruction of floc produces very fine particles, and thus induces the difficulties of bubble-particle collision during the precipitate flotation in column."

Jan 1, 2003

By P. Basarova

The attachment of bubbles onto a collecting surface is an ubiquitous natural phenomenon, playing a critical role in numerous practical processes. The goal of the project is to broaden the knowledge about hydrodynamic interactions between small bubbles and large solids that occur in nature and industrial processes. Focusing on collision processes between a single rising bubble (Db<1 mm) and a larger falling spherical particle in stagnant liquid, the theoretical model describing the bubble trajectory is given here. The model is based on analysis of forces acting on the bubble, and utilizes equation for the bubble motion. Mobile and immobile type of bubble surface mobility are considered. The calculated results are compared with the experimental data; here a high-speed video camera was used to capture the bubble motion and bubble-particle interaction. Very good agreement between experimental and calculated data was found. For both types of surface mobilities, the bubble deviation in the horizontal direction is nearly linear. The proportion constant is bigger for immobile bubble surface and increases with the bubble size. Furthermore, particular forces acting on bubble were studied. A similar course of relative bubble velocity and force impact was observed for identical bubble position. For cases when the bubble centre is close to the particle axis, only deflection in one direction is observed. When the bubble is reaching the maximum trajectory, the force ratio is changed. The bubble is firstly pushed away from the particle, but when it is within close distance from the particle, the bubble is pushed towards the particle.

Sep 1, 2012

By Nicolás Luis, Qi Liu, Gonzalo Montes-Atenas

"The prediction of froth flotation performance is still an unresolved topic. Classic industrial models based on particle size, elemental and mineralogical information provides recovery results with deviations that may become significant. One possible reason for this deviation may be the fact that the current liberation analysis provided by electron microscope based techniques does not take into account the outmost surface layer composition of liberated particles. In order to complete the description provided by the liberation analysis, other spectroscopy techniques measuring the extreme surface of the minerals can be tested. For instance, X-ray Photoelectron Spectroscopy (XPS) is a technique which measures the first tens of nanometers providing elemental composition over the particle surface and allows resolving the elemental associations present at the surface sample. However, this information needs to be statistically robust, reproducible and most importantly representative of what is occurring in the process. The aim of this research work is to develop a statistical model based on particle population to evaluate the feasibility of turning the XPS technique into a metallurgical tool. The model consists of classic statistical population arranged in a bed of heterogeneous particles with a known grade and mineral liberation. The simulations showed that the XPS results statistically followed a well-defined pattern. The statistical results were confronted with pilot plant results obtained from a rougher bank when processing a copper sulfide ore from a Chilean mine site. It was observed that the probability function distribution was in agreement with the experimental data. Further analysis on how the XPS results provide valuable information improve the computation of froth flotation recoveries is also discussed."

Jan 1, 2014

By Javier Baladron, Mijail Villar, Brandt Henriksson

"In this presentation an overview will be given of what has been observed by the authors in the copper concentration industry, with a large diversity of tailing thickeners operating under different conditions, although many of them are located in the same neighborhood. A closer look will be taken at the reported performance from different sites and from different thickener designs, either conventional or high rate, including those that were retrofitted, regardless of the thickener brand. An analysis is also made of the generic correlation of the size of the thickener and the performance in terms of solids loading (or unit area) and % solids. The paper envisions a technology development route, makes a brief analysis of the economic impact of the suggested route and points out the need for development in technologies around tailings thickeners, such as automation, yield stress measurement, slurry pumping and construction methods."

Jan 1, 2014

By Chuanyao Sun, Yang Yu, Zhen Guo Song, Wei. Ming’An

"Carbonate minerals are very important mineral source of extracting metal, radioactive element and rare earth elements. Furthermore,some carbonate minerals, such as calcite and dolomite, are common and important components of sediments and sedimentary rocks. Many flotation processes involve the separation of valuable minerals with carbonate minerals. So it is of great significance to the flotation theory and industrial practice to investigate the flotation behaviors of carbonate minerals. As regulators, metal ions play a major role in minerals flotation. The study of influence law of metal ions on minerals flotation is helpful to eliminate or utilize the effect of metal ions. In this study, calcite and smithsonite laboratory scale flotation, surface analysis and zeta potential determination in the presence of Fe(II) ion were performed to investigate the effect of Fe(II) on carbonate flotation. The results show that Fe(?) depresses the flotation of calcite and smithsonite. The depression effect of Fe species on calcite and calamine flotation can be improved with the increase of Fe(?) concentration. The zeta potential measurements and surface analysis show the existence of iron hydroxide products on mineral surface, which may be link to carbonate site instead of exchanging with calcium on the mineral surface. Fe species on the mineral surface inhibit the interaction between the reagents and calcite/smithsonite through the formation of surface precipitation coating on the calcite/smithsonite surface when the Fe(?) concentration is higher."

Jan 1, 2014

By Rajamani R. K.

The design of tumbling mills has progressed from the Bond work index concept of the 1950s to the population balance concept of the 1980s and then made a quantum leap forward with the discrete element method in the 1990s. The failure of a SAG mill at the Grasberg mine site set in motion the inquiry into the role of shell lifter geometry on the profile of the charge motion within the mill. Quickly, it became evident that this could only be accomplished by tracking individual motion of ore particles and grinding balls and not by study of en masse motion of the charge that had been established previously. The discrete element method (DEM) which was prevalent in the civil engineering literature at that time proved suitable to tackle this simulation problem. In 1991, the two dimensional simulation of laboratory scale mills was validated with the DEM. Later this simulation method evolved into ?MillSoft?? a simulation software package for the design of lifters in ball and SAG mills. MillSoft?simulations proved that cataracting charge motion is not conducive to the life of lifters. The old rule of thumb that the number of shell lifter rows should equal twice the diameter of mill in feet was shattered by simulation results. Instead, the number of rows equal to the diameter of the mill in feet, providing that the lead angle of lifter is around 25 degrees, was established as being more optimal. This bold design change was first implemented and tested by Mark Sherman at Alumbrera Mines in Argentina. Two 36-ft SAG mills responded extremely positively to the design change. This success was immediately repeated at Collahuasi, Pelambres and other mines in South America. The design change has so far exceeded expectation that there is not a single SAG mill around the world today that does not employ a relief angle on its shell lifter. The DEM method has advanced in the hands of the author, mining companies and universities, notably in Australia and South Africa. Today, three-dimensional simulation of charge profile and slurry transport is a standard in the design of mills. There is strong pursuit of a virtual comminution machine with DEM in Australia. In South Africa, an experimental method known as positron emission tracking is emerging as a method for tracking particles in grinding mills. The computational burden of computing with millions of particles in three-dimensional simulations has been eased to less than a day with a technique known as GPU computing. Keywords: DEM method, GPU computing, SAG mill, tumbling mill simulation, discrete element method

Sep 1, 2012