Search Documents

By J. D. T. Capocchi, M. B. Mourao

The rate of reaction between iron oxides and carbonaceous materials, agglomerated as pellets, was studied experimentally by measuring the weight loss as a function of time. The effects of temperature, carbon type, inert gas flow rate, pellet size and additions (sodium. carbonate and Portland cement) were determined. It was shown that the value of the apparent activation energy can display large deviations under different experimental conditions; in the present work it was found to be 226.6 kJ/mol. The reaction with coke is slower than with charcoal, and the rate increases as the flow of inert gas in the reaction vessel decreases. Comparison of the rates for pellets of different sizes has shown that for small pellets the initial rate is faster but that it slows down at high conversions owing to the penetration of inert gas into the pellet. Additions of sodium carbonate and Portland cement increase the rate; sodium. carbonate promotes the catalysis of the Boudouard reaction, which is the slowest of the partial reactions. The increase in the rate with Portland cement is attributed to the release of water vapour

Jun 18, 1905

By S. P. Singh

The purpose of the cut is to provide a free face to which the remainder of a development or breasting round can break. The results of field testing in drifts and at a quarry face were used as a basis for a description of the rock breakage and flushing mechanism in the cut. It was concluded that the important features of a cut design are proper hole spacing, sufficient relief volume, drilling accuracy and relief holes slightly longer than the planned length of the round. The void space provided by the relief holes should be about 15% of the cut volume, with more required in weak, highly fissured rocks. The importance of drilling accuracy increases with round length, an error being magnified by the small blasthole spacing. The first hole pulls only about 20% of the round length, 4-6 holes having to be fired before the cut is pulled close to its design depth. The first four blastholes should be fired with a minimum inter-hole delay of 100 ms to provide progressive relief of burden and avoid the superimposition of ground vibrations. The earliest-firing charge should be closest to the relief area and act laterally, while the first of the vertically-fired charges to be detonated should be the uppermost. Problems during cut-pulling include sympathetic detonation, dynamic pressure desensitisation, charge disruption and freezing of the cut

Dec 1, 1995

By C. A. Jeffrey

The Dirtlow Rake vein deposit, which is up to 12 m thick, contains a range of paragenetically linked replacement mineralisation styles typical of many Mississippi Valley-type deposit environments. The main ore zone lies within the solution collapse breccia domes, the more southerly of which has recently been well exposed, allowing its relationship to the associated mineral-hosting structures to be studied. The domes were largely formed during early silicification, propagated by dissolution collapse and infilled by subsequent fluorite-barite mineralisation. The location of pipes and pervasive replacement was also controlled by early silicification. Structurally controlled bow tie shears were formed as a result of fluid access at fracture-bedding plane intersections. The nature and distribution of the mineralisation styles indicate that the degree of fluid access, residence time of solutions in contact with the wallrock and susceptibility of the limestone to silicification each played a major role in dictating mineralisation

Jun 19, 1905

By A. S. W. Kurny, M. Z. Huq

Bangladesh ilmenite is partially altered, containing pseudorutile, rutile and haematite as well as the predominant ilmenite phase. A typical analysis is 39.45% TiO2, 24.19% FeO and 33.0% Fe2O3. Reduction of the ilmenite by charcoal was found to involve two major reactions: conversion of pseudorutile into ilmenite and rutile, and change of ilmenite into metallic iron and rutile. The first, which was much the faster reaction, was responsible for an initial increase in ilmenite content with reduction time at lower temperatures. Apart from these two major reactions, rutile was reduced to lower oxides at 1 100 degrees C with a consequent decrease in its XRD peak height

Jun 19, 1905

By R. A. Lord, H. M. Prichard

Paper presented at Mineralisation in the Caledonides, the Mike Gallagher memorial meeting held in Edinburgh, 27-28 June 1996. The complex exemplifies a class of olivine-rich, platiniferous ophiolite complexes generated by unusually high degrees of hydrous melting above a subduction zone. Crystallisation of abundant olivine from unusually picritic magmas produced an exceptionally thick sequence of crustal dunite cumulates. Significant (1-4 ppm) concentrations of Pt+Pd occur where sulphide-bearing dunites are spatially associated with podiform chromite concentrations. In the area north of the Balta Sound, the chromitites appear to lie in distinct stratigraphic zones. A detailed programme of lithogeochemical and soil-rock interface geochemical exploration led to the intersection by diamond drilling of three stratiform horizons of sulphide-bearing dunites and associated precious-metal mineralisation. Patterns of cryptic geochemical layering, at scales from 200 m to less than 1 cm, suggests open-system fractionation

Jun 19, 1905

By B. Tiryaki, O. Z. Hekimoglu

Shearer drums are a critical component in the overall performance of coal shearers, with the cutting performance depending very much on the disposition of cutter tools on the drums (the tool-lacing arrangement). A series of practical and theoretical studies has been undertaken to investigate aspects of shearer drum vibration in terms of circumferential pick spacing. A number of commercially available drums were redesigned and the lacing patterns compared with those of the original drums under near-uniform conditions. Mine trials were carried out at the Middle Anatolian lignite mine in Turkey with drums fitted on Eickhoff type EDW-230 double-ranging drum shearers. It was found that the performance of drums could be improved if the concept of circumferential pick spacing was taken into account in CAD packages along with the existing design parameters such as cutting rate, reduced dust, low pick consumption and low down-time

Jun 19, 1905

By B. B. Dhar

Slope stability at the proposed mine in Rajasthan was analysed in two dimensions using a finite difference code. The properties of the rock material were determined in the laboratory and subsequently modified to approximate those of the in situ rock mass. Geotechnical mapping was undertaken to determine the critical orientation of structural discontinuities. The results of the work indicated that an open pit 148 m in depth would be stable with overall slope angles of 60 degrees

Aug 1, 1994

By A. E. Tercan, D. Mamurekli

Ordinary kriging on the assumption of a gaussian error distribution and indicator kriging were used to derive the probability that a given calorific value would or would not be exceeded by coal from an area of a deposit. The two techniques led to similar probability maps despite local differences; the lack of an absolute reference makes it impossible to judge which method is better for this particular application

Jun 19, 1905

By S. P. Godby, S. P. Sharples

Wind-tunnel tests were carried out of the conditions under which nuisance dust particles (100-1 000 micrometres) become entrained by wind. A laser entrainment monitoring system (LEMS) was used, and was found to provide an accurate means of assessing nuisance dust emissions from a surface. Accurate determination of the threshold entrainment velocity of dusts using the LEMS gives a baseline against which the performance of dust control techniques can be evaluated. Minerals tested included coal, petroleum coke, limestone, sand and pulverised fuel ash. Pilot field trials of a portable wind tunnel equipped with the LEMS have been successfully completed, providing a means of validating laboratory results in the field

Jun 19, 1905

By T. Ogasawara, J. P. Barbosa, A. J. Monhemius, F. T. Da Silvia

A thermodynamic analysis of the sulphation of rare-earth phosphates and the water-leaching of rare-earth sulphates was used to guide experimental work on the sulphation and leaching of concentrates from Pitinga. It was concluded that the sulphuric acid digestion of xenotime is technically feasible and could be used industrially to produce yttrium and other rare-earth oxides. Yttrium extractions of more than 90% were obtained by digestion at 503 K for 4 h at an acid:concentrate ratio of 2:1 with particle size -0.053 mm. The apparent activation energy at temperatures less than 473 K, as determined from the Arrhenius plot, was 11.0 kJ/mol, indicating that the reaction is controlled by the diffusion of the reactants or products through the sulphate layer

Jun 19, 1905

By B. M. England, M. V. Swain, N. Bristow, R. D. Dukino

The toughness and fracture mechanisms of ores with significantly different microstructures from Yandi, Koolan and Mount Whaleback were studied with a view to understanding their degradation behaviour. Bulk fracture toughness was determined by the 3-point single-edge notch beam test and the results interpreted using Weibull statistical analysis; indentation fracture mechanics was also used to measure fracture toughness of the different mineral forms and to understand their response to contact fracture

Apr 1, 1995

By D. J. Burdon, Anthony Caplan

"(1) The radiological appearances of pneumokoniosis on the Kolar Gold Field is described in detail. The characteristic abnormality is the. presence of a diffuse, fine annular and punctate mottling. (2) The frequency of symptoms could not be determined with any degree of accuracy, but it is believed that symptoms are absent and there is no incapacity until profuse radiological mottling is present, i.e., after long exposure to dust. (3) There is an increased predisposition to tuberculosis, which, if it occurs, affects the prognosismost unfavourably.(4) Pathological examination shows that the radiological mottling is due to the presence inthe lung of numerous small dust-cdll aggregates (up to T5 mm. in dia.) deposited around the smaller bronchioles and blood-vessels.(5) The dust-cell aggregates are relatively acellular but when tuberculosis is superadded thereis an excessive cellular and fibrotic reaction.(6) The difficulties of defining the radiological and pathological appearances of early pneumokoniosisare discussed.(7) The incidence of pneumokoniosis in 7,653 workmen with 5 or more years’ undergroundservice was 43-75%, but it is suggested that in future the incidence will be appreciably lower.(8) The methods of- dust production and the chemistry of mine dust are described. It isshown that the free silica-content of air-borne mine -dust is relatively low.(9) The aetiology'of the pneumokoniotic lesion is discussed."

Jan 1, 1947

By S. Henley

Paper presented at a meeting on: Artificial intelligence in the minerals sector, held in Nottingham, UK, 20 April 1993 (original title: The database: a pre-requisite for large-scale use of AI in mining). Artificial intelligence is a term which has been widely applied to different techniques including rule-based systems using inductive and deductive logic algorithms, neural networks, learning systems and genetic algorithms. In principle it should be applied to adaptive statistical techniques. Some of these applications have been coded in languages which are specifically suited to the novel requirements of AI but are not easy to integrate with more traditional computing methods. Efforts have been made to bridge the gaps, particularly with database management systems and such efforts at integration should provide the key to future success in the application of AI. A field which has been termed "knowledge engineering" cannot be credible as such if it fails to provide easy access to raw materials of "knowledge" i.e. the data residing in databases. In the mining industry there are a number of significant areas in which AI could usefully be applied throughout the industry, but its advance is slow because of the lack or inefficiency of such database links. Current development of object-oriented database systems for geology and mining holds out hope for such integration in the foreseeable future

Apr 1, 1994

By P. A. Rossouw, G. A. Fourie

Several attempts have been made over the latter half of the twentieth century to devise a system for the classification of underground mining methods. None of these are found to be totally successful. A revised classification is suggested with three main categories being identified by reference to fill requirements, steep stopes and stratified geological environments. Methods always needing lasting mass or structure fill include methods with timber-structured stopes and those with mass-filled (or cut-and-fill) stopes. Methods associated with steep stopes are subdivided into steep-stope-specific caving and steep-stope-specific non-caving (or self-supporting) methods. Methods not in the first two categories, often used in stratified geological situations, are not necessarily restricted to stratified environments and include caving as well as non-caving varieties. This category is further divided into room-and-pillar mining, longwall and shortwall coal mining and the type of open stoping found in gold or platinum reefs comprising overhand, underhand and breast-stoping variations

Dec 1, 1996

By A. L. Grabovski

The potential of eccentric cone crushers for fine crushing has been improved by increasing the swing frequency of the moving cone, balancing the crusher, ensuring uniform feed via a rotating funnel with sideways discharge, introducing hyperbolic motion and employing the inertia crushing method, but further improvements to the specifications of existing cone crusher designs are limited by the rigidity of their kinematic coupling. A new design has been developed which combines two crushing modes, stone on liner and stone on stone, each with its own advantages. The main aims are to produce finer materials and to reduce liner weight. The benefits include an increase of more than 10% in the output of fine particles, improved protection of the liner against wear, as a result of filling of the cavities by material being crushed, and the use of almost 20% less material in casting of the liner. The chamber can be used in place of the usual liners of fine cone crushers

Jun 21, 1905

By G. Kill

Although other energy commodities have developed successful futures contracts, long-term contracts still dominate the coal market. To establish whether coal markets will develop in the same way, coal price and volume data are tested against a set of criteria considered to represent some of the factors contributing to the development of a successful futures contract. Coal meets only some of the criteria: market players are subject to little risk in quite a stable market, have strong preferences for the specific nature of long-term contracts and profit from product uniqueness, each trade being individually negotiated. Potential structural changes in the western European market are not felt to be sufficient to create demand for a coal futures contract, but an empirical model has been developed that could form the basis of a further study to predict the potential for success

Aug 1, 1994

By J. S. Coats, G. E. Patts, N. Hughes

Conventional sampling methods are known to suffer from the variable loss of fine gold by elutriation. Freeze sampling yields representative and quantitative data that, when combined with information on the sedimentology of gravel-bed rivers, may facilitate the development of improved dispersion models for source detection. It is suggested that freeze sampling may have particular application to the orientation stage of a large gold exploration survey

Jan 1, 1991

By H. L. Paterson, R. R. Keays, M. J. Donaldson, D. J. Boyack, M. F. Smith, J. J. Gresham

"Albite-rich sedimentary rocks that contain abundant Fe sulphides occur in the lower portion of the ultramafic sequence at Kambalda and their broadly antipathetic relationship to most of the nickel orebodies is well documented. These sediments generally contain less than 0.1% Ni, but nickeliferous equivalents with 0.3 to >6% Ni occur locally in close spatial association with more typical volcanic peridotite-associated massive, matrix and disseminated ores. Nickeliferous sediments have been mined at several locations at Kambalda but, collectively, they constitute less than 2% of the total Kambalda nickel reserve. The nickeliferous sediments occur both on the ultramafic-footwall basalt contact and within the lower part of the ultramafic sequence, and are usually less than 5 m thick. They are commonly finely laminated rocks with a cherty appearance, composed essentially of layers of albite+quartz±amphibole, alternating with pyrrhotite+pentlandite±pyrite layers. Some contain a minor amount of carbon. The sediments are only of ore grade (> 1% Ni) immediately adjacent to massive Fe-Ni-Cu sulphides, which are interpreted as normal magmatic ores on the basis of geochemistry and the presence of distinctive ferrochromites. The nickel content of the sediments decreases to background levels (<0.1%) within about 20 m of the massive sulphides. In most locations the massive sulphides clearly have been emplaced tectonically within or adjacent to the sediments, which are commonly highly deformed. Typical nickeliferous sediments contain about 1% Ni, 0.1% Cu, 0.1% Zn, 400 ppb Pd, <0.2 ppb Ir and 10-200 ppb Au. They have lower Ni/Cu (average 10), higher S/Ni (average 6) and higher S/Se (average 11 200) than associated massive sulphides (average 40, 4.8 and 7400, respectively). The Pd/Ir ratio of the nickeliferous sediments (typically > 1000) contrasts markedly with that of associated massive sulphides (average ca 16).The high Pd/Ir values are similar to those which have been reported for hydrothermal Fe-Ni sulphides and barren sulphidic sediments of probable volcanic exhalative origin. They preclude a direct magmatic origin for the sulphides in the nickeliferous sediments, though S/Se and S isotope data indicate a magmatic source for the sulphur. The restriction of nickeliferous sediments to within about 20 m of normal magmatic sulphides and the lack of a widespread Ni dispersion halo suggest local redistribution of originally magmatic Ni. This probably occurred by diffusion and hydrothermal mobilization during deformation and amphibolite-facies metamorphism. Although not totally ruled out, a volcanic exhalative origin for the Ni seems unlikely."

Jan 1, 1984

By G. M. Zhao

The gasification of lump coke with CO2 was studied in a fixed-bed reactor. The effective diffusivity of the gas was evaluated from measurements of the reactivity of the lump coke, produced by BHP Steel in New South Wales, and from kinetic parameters that were determined from the reactivity of fine grains. The grain model of effective diffusion in porous media was adopted to express the gasification rate of the lump coke and was found to fit the experimental data well. The relationship between reactivity and textural characteristics of the coke was examined

Jun 18, 1905

By I. Marklund, W. Hustrulid

Sublevel caving is likely to remain the dominant system at both Malmberget and Kiruna for the foreseeable future. The sub-level interval has increased from 12 m in 1983 to 30 m, requiring more effective drifting and the development of a contour blasting technique to reduce requirements for rock reinforcement. Production drilling is mainly by hydraulic hammers or water-powered in-the-hole machines drilling 115 m diameter holes. Loading operations are undertaken 7 days/week with 15-25 tonne capacity electric shovels. Production has increased by nearly 70% since 1983 and productivity has risen threefold

Dec 1, 1995