Search Documents

By George D. Raitt, Rudy Lyon

Until fairly recently, Down-The-Hole (DTH or DHD) hammer drilling was never really a factor in large scale open pit surface mining. It was a method confined to water well drillers, aggregate quarries and limestone mines where the hole size rarely exceeded 6-1/2" (165 mm). Also it was somewhat limited to the harder rock areas such as the North East and South East United States. The trend in the big mining pits for coal, copper, gold and iron, was for the big rotary drill rigs with lots of muscle in pulldown, bitload and rotary torque.

Jan 1, 1998

By Robert C. Fouchard, Gordon Chalmers, David E. G. Jones, Ivana Alilovic, Phillip D. Lightfoot

There have been numerous international instances over the last several years in which pumping emulsion explosives has resulted in accidents, apparently as a result of increased thermal sensitivity under these conditions. The key questions for the explosive industry are (1) what are the parameters that influence the sensitivity of emulsion explosives and, (2) how do these various parameters interact. To address the sensitivity of emulsion explosives to various parameters, a study was undertaken using an accelerating rate calorimeter (ARC) and a heat flux calorimeter (HFC). The effects ofthe addition of ammonium nitrate (AN) prills and different grades of aluminum (Al) on the thermal behaviour of emulsion explosives were determined. Additionally, changes in pressure, atmosphere (inert or oxidizing) and sample vessel material were assessed for their impact on thermal sensitivity. Addition of AN prills, fine granular Al or atomized Al did not affect the onset temperature for exothermic decomposition, so that the maximum “safe” temperatures for emulsions containing these additives will be similar. There were differences in the rates of self heating, however: AN prills decreased the rate of self heating, whereas atomized Al increased it. The emulsion formulations containing atomized Al produced small holes in titanium vessels. This phenomenon did not occur in Hastelloy C vessels, providing a reminder that materials of construction need to be carefully considered for equipment used to manufacture or handle emulsion explosives.. Both ARC and HFC experiments gave lower onset temperatures in air than in argon. We attribute this to oxidation of the oil phase by air. This result is significant for dry-running pumping conditions, where emulsion is heated in the presence of excess air.

Jan 1, 2000

By Mark S. Stagg, Steven V. Crum, Stephen A. Rholl

As part of its ongoing research concerning rock fragmentation by blasting, the Bureau of Mines has undertaken a series of test blasts where six cylinder-shaped pieces of granite rock were fragmented using high explosives. The tests were intended to: 1) Establish a dataset that could be used in the development and verification of theoretical models that simulate rock blasting and 2) To add to the fragmentation data currently being collected by Bureau researchers. The cylindrical geometry was chosen so that the fragmentation could be directly compared to two-dimensional computer simulations that assume an axisymmetric configuration as well as more sophisticated three-dimensional models. The granite cylinders, Carnelian granite and Charcoal granite, ranged in size from about 0.46 meters (18 inches) to 0.58 meters (23 inches) in diameter by 0.91 meters (36 inches) to 1.52 meters (60 inches) in length. Physical rock properties tests performed on the Charcoal granite cylinders indicated that the rocks did in fact have similar physical characteristics. PETN-based detonating cord and dynamite were used as the explosive charges and estimates of the values of some important physical properties are given. For the first five tests, the blasted rock was contained by a heavy rope mat suspended inside the Twin Cities Research Center's blasting shelter. The fragments from each of these shots were sorted and weighed to determine the corresponding fragment-size distributions. Even though different types of granite and cylinder sizes were used, similar fragment distributions were produced from shots that used a similar explosive, in this case the PETN-based detonating cord, and comparable burden-to-charge diameter ratios. Significantly coarser fragmentation was produced from a blast that used dynamite as the explosive charge. Fragment velocities were calculated using photographic data from the sixth test which was shot unrestrained in a quarry and filmed with high-speed cameras.

Jan 1, 1990

By Michael Swisdak, John Tatom, James Tancreto

In 2002, testing was proposed to generate needed data to assist in developing improved explosives safety standards within the US Department of Defense. This testing emphasizes two major areas: (1) full-scale donor/acceptor trials examining debris generation and acceptor response and (2) debris perforation testing of representative roof/wall materials. The full-scale donor/acceptor trials are referred to as the SciPan series. The first three tests in the SciPan series have been completed, as has the first phase of the SPIDER program. This paper describes the status and future of these testing programs, reasons for choosing specific tests, potential benefits, and planning for future phases.

Jan 1, 2006

By Randall M. Wheeler

Many blasting companies are using simulated production ground vibration waveforms to aid them in the control of their vibration effects. The simulations are typically produced by using a seismograph to record a signature waveform from a single hole shot and subsequently applying the various delays to be used in a proposed production design. The ability of this simulation method to give good results usually depends on three primary factors. These are: 1) the homogeneity of the seismic travel path from hole to hole; 2) the consistency of the seismic energy release per unit of explosive from hole to hole; and 3) whether or not the delays fire as planned.

Jan 1, 1991

By Robert Hopler

CHAPTER I. DEFINITIONS AND CLASSIFICATIONS. Definition of Explosives. SECTION 1. The term “Explosive” or “Explosives” whenever used in this ordinance, shall be held to mean and include any chemical compound or mechanical mixture that contains any oxidizing and combustible units, or other ingredients, in such proportions, quantities or packing that an ignition by fire, by friction, by concussion, by percussion or by detonator of any part of the compound or mixture may cause such a sudden generation of highly heated gases that the resultant gaseous pressures are capable of producing destructive effects on contiguous objects or of destroying life or limb, and includes all the articles specifically mentioned in Section 3 herein, and all other similar articles

Jan 1, 2013

By Christian Dye

"The following paper focuses on the developing relationship between the members of theInternational Society of Explosive Engineers (ISEE), and the mining students from the BritishColumbia Institute of Technology (BCIT). During the past two years mining students and theISEE members have worked closely in developing a student chapter within the society and onFebruary 1st 2015, the first Canadian Student Chapter was recognized at the annual generalmeeting in New Orleans. This paper discusses the benefits that both the industry and studentsgain with a strong relationship. The mining students recognize the importance for filling the rolesof retiring members of the society and industry. Prior to 2015 the school had only offered a twoyear diploma program in mining and mineral exploration methods. That included a brief sectionin the use of explosives in the mining industry. In September of 2015 students were recruited forthe first ever Bachelors in Mining and Mineral Resource Engineering program. This engineeringdegree includes a full four month course in advanced blasting and rock fragmentation. Studentssuccessfully completing the diploma program will have an entry level of technical understandingin how blasting is conducted. The students successfully completing the bachelor degree will havean in depth technical understanding of explosives and rock fragmentation. Having this uniqueand dynamic multi-level program provides the explosives industry with a pool of talent that canbe used to fill positions with graduates for all levels of the blasting industry."

Jan 1, 2016

By Kirlk Yeager

"Ammonium nitrate (AN) is commonly mixed with a wide variety of additives to produce specialty formulations. Two additives commonly utilized are sodium nitrate (SN) and sodium nitrite (SNi). Application of the nitrite is primarily limited to gassing of emulsions. The nitrate, however, is incorporated in a wide variety of formulations. The effect of both these materials on the thermal stability of AN was examined. Experiments initially utilized lab-scale testing methods (sub-milligram sample size), such as differential scanning calorimetry (DSC), with scale-up to cook-off analyses (16 g) eventually applied. Labscale testing indicated that the presence of SN and SNi (both at 5 wt%) produced no harmful effects on the thermal stability of AN. The cook-off results did not agree with those from the lab-scale analyses, with both SN and SNi creating tremendous thermal destabilization of AN. These effects were seen at additive levels as low as 0.1 wt%. When SNi was employed as the additive, cook-offs became violent enough to create explosions in the testing apparatus. Although SN did not create as spectacular a destabilization, it did lower cook-off temperatures to approximately the same level as SNi. The dangerous situation created by SN andSNi seemed to be limited to cook-offs conducted in sealed vessels. If the SN/AN or SNi/AN formulations were allowed to cook-off in vented vessels, the thermal destabilization of AN did not occur. These results seemed to indicate that even “trace” amounts of what might ordinarily be viewed as benign additives could create significant destabilization of AN-based explosives under proper circumstances. Conditions created by blocked pumps, or deep boreholes could well overlap those produced in sealed cook-off vessels. In addition to showing the hazards potentially created by “benign” additives, the study also stressed that experiments designed to evaluate thermal hazards must include duplication of field variables to the fullest extent possible. "

Jan 1, 1999

By Kunihisa Katsuyama, Yuji Ogata, Yuji Wada

Test blasting was carried out to study the flying characteristics of rock mass caused in bench blasting. The quantity of explosives was increased from 7.6kg to 9.1kg and the Minimum burden was changed from 131mm to 451mm. The effect of condition for the characteristics of fly rock were considered. The fly rock was observed using the high-speed camera and video to study the flying characteristics of the rock mass caused in the bench blasting. Numerical simulation of fly rock was carried out using DDA (Discontinuous Deformation Analysis) method. It was clear that the DDA method can be applied in the simulation of fly rock caused in bench blasting.

Jan 1, 1997

By Scott G. Giltner, Alex Schwenk

This paper is an update on a paper presented at the 2022 ISEE conference. The original paper presented how the mine operator desired to open up ore reserves near several mine structures including two crushers, the conveyor belt drive and the concentrator thickeners. In order to open up additional ore for extraction (over 3 million long tons or 3 million tonnes) it was necessary to blast out two benches near the mine structures. Since the two benches have been successfully shot, the mine has now conducted nine production blasts in this area at distances as close as 116 m (380 ft) to the two primary crushers. These production blasts are full size production blasts consisting of up to 300 or more blast holes. For these blasts the two primary crushers were still the critical structures as they were the production life blood of the mine. If the crushers were shut down due to any damage from the blasting, the revenue of the mine would be adversely affected. As with the initial bench blasts, two issues provided an extra challenge to the blast design. The first was that the blast holes were still considered large diameter at 12¼ inches (311 mm) and 16 inches (406 mm). The second issue was that the bench heights were short, with the average varying from 34-40 ft (10.3-12.2 m). This combination of large diameter blast holes with a short bench provided an unfavorable geometry for the goals established by the mine management. The mine management established the following goals. 1) None of the mine structures would be damaged by fly-rock. 2) Minimize the blast vibrations at the crushers. 3) The last goal was to produce a muck pile that could be dug easily by hydraulic shovels. Electronic detonators were applied to achieve the necessary control of the blast and optimal fragmentation throughout the mine. UAV surveys of the blast area were also conducted to provide a 3-D representation of the free faces and bench surface. The 3-D point cloud produced from this was used to measure the shape of the free faces. Once the shape of the free faces was quantified, it was possible to establish proper placement of the crest holes and develop a custom explosive load for each blast hole. The results of the nine blasts have provided what the customer requested. The peak vibration level at the crushers for the nine production blasts was 1.6 in/s (40.6 mm/s) at a frequency of 18.9 Hz. There have been no fly-rock or blast vibration issues at any of the nearby mine structures. As a result, the mine has been able to maintain its production with no downtime. The muck piles have been well fragmented with reports from the shovel that they have all dug well.

Jan 21, 2025

By Chad Ducey

The proper utilization of energy in an explosive column is of paramount importance to the success of any blast. Historically, Powder Factor (the weight of explosive per mass or volume of material to be blasted or its inverse), has dictated the blast design. The concept of Energy Factor is a more effective method to design a blast. In order to utilize explosives efficiently, the energy contained in any given product must be quantified. The Powder Factor method, although historically successful, assumes that a pound of cast pentolite affects the material to be blasted the same as a pound of ammonium nitrate / me1 oil (ANFO.) Years of experience and scientific testing have led the blaster in the field to believe otherwise. The next logical technological step is Energy Factor. The Energy Factor method that will be discussed in this paper takes into consideration not only the weight of the explosive, but also the weight strength (Cal/g) and the density (g/cc) to yield a constant relative Energy Factor. The result of such a method is a factor that can be used in the field exactly the same as Powder Factor, but that reflects the relative energy of any given product in terms that will reflect the relative cost benefit of that explosive selection. The Energy Factors associated with different available explosives make it possible to compare the difference in the amount of energy per loaded pound in each unit length of borehole. This paper will examine the concept of Energy Factor in an in depth manner and also compare this quantification method to that of Powder Factor. It will also demonstrate the value of using Energy Factor and how it can improve the efficiency of a blast design. The misconceptions that come along with using Powder Factor will be examined and comparisons will be made between boreholes loaded using Powder Factor and those that are loaded using Energy Factor. This paper will clearly define the differences between these blast design methods and allow the reader to realize the production, quality, and economic advantages of using the Energy Factor method.

Jan 1, 2000

By P. Ross, O. Rielo, P. Katsabanis

Selection of delay times to optimize fragmentation has been a controversial topic among researchers and blasting practitioners. The paper reviews all available experimental information, ranging from small and medium scale tests in geologic materials to small scale tests at the laboratory and synthetic materials, simulating rock. Tests have been re-analyzed and discussed in terms of the information they present and the limitation of the testing environment in representing actual conditions. New results obtained from blasting experiments in specimens made of a grout have provided a clear picture of the effect of delay on fragmentation. The grout used has a strength of 60 MPa (8700 psi), density of 2.5 g/cm3 and P-wave velocity of 4000 m/s (13100 ft/s). Each block was placed in a yoke to eliminate unwanted reflections and the desired delay was obtained using the appropriate length of detonating cord between holes or sub-millisecond electronic detonators. Delays ranged from 0.1 ms/m (0.03 ms/ft) of burden to 16 ms/m (4.9 ms/ft) of burden. Fragmentation was obtained using screen analysis of the collected fragments. Delay time has been shown to be a significant parameter affecting fragmentation and back break. Generally larger fragments and less back break was observed at short values, while fragmentation somewhat deteriorated at significant delay times, compared to what was observed at intermediate delay times. The work is now extended to include the effect of energy partition on fragmentation as well as the effect of initiation point and coupling ratio.

Jan 1, 2014

By Earl C. Hutchison, John Loviza

At the Metropolitan Nashville International Airport, with its more than 600 scheduled daily flights from American Airlines hub operations, other scheduled airline flights, Tennessee Air National Guard operations, as well as numerous industry air flights, the excavation of 300,000 cubic yards of rock was required without disrupting airport operations for a cut and cover underground tunnel with a 4 lane US Highway and new airplane runway to extend across it's top. In addition to the excavation, the removed rock was to be broken to specification type that was clean and of small size for fill in another area of the airport property. The blasting was limited to two 1/2 hour windows per day and stiff monetary penalties were in place for schedule slippage of each phase of the project.

Jan 1, 1992

By John T. Aler

The U.S. Bureau of Mines has been studying the problem of why explosives detonate weakly or misfire during blasting in underground coal mines. Cross-borehole shock wave interaction has been identified as a predominant mechanism causing explosives to function improperly (1)(Underline numbers in parenthesis refer to items in the list of references at the end of this report.). Cross-borehole shock wave interaction can be simulated in a laboratory setting, making possible the replication of tests in sufficient numbers to understand and quantify some of its effects on permissible explosives (2). The work presented here investigates the capacity of explosives to partially recover from the desensitizing influence of the shock wave. The recovery trend of different explosives can indicate optimum blasting patterns useful for minimizing borehole charge malfunctions.

Jan 1, 1991

By Thomas Barkley

Mining tradition holds that a parallel round underground can not be any deeper than it’s smallest face dimension. ln other words, a mine using a 12’ (3.7 m) high by 24’ (7.3 m) wide room and pillar mine, the deepest pull that can be achieved is plus or minus 12’ (3.7 m). After experience with decking of rounds in a 12’ (3.7 m) diameter shaft to achieve more than 12’ (3.7 m) advance per round, the concept of deepening the pull on horizontal parallel rounds seemed to be a feasible concept. Tests were conducted in a conventional room and pillar metal mine with a round size of 12’ (3.7 m) high by 24’(7.3 m) wide. Standard rounds were drilled with a 16’ (4.9 m) steel as parallel rounds to an average depth of 14.5’ (4.4 m). The average depth of pull on these rounds was about 13’ (4.0 m). Using the available drilling equipment, 20’ (6.1 m) drill steel was used to drill holes to an average depth of 18’ (5.5 m). Five rounds were drilled and shot with a resulting aven$e pull of 16.2’ (4.9 m) or 90 % of drilled depth. Rounds were designed with decked bum cuts to maximize depth of pull in the cut area An innovative method of de&mining drilling accuraq was used to estimate it’s effect on depth of pull in the rounds. This method used a standard automatic 35-mm camera and scaling to determine the average drill deviation for many of the holes in the rounds.

Jan 1, 2000

By G. Walsh, L. Wolkovitch, A. Savage, V. Romero, T. Zimmerly, G. Imahara, J. Hyneman, K. Byron, D Tapster, S. Belleci, J. Metzger, M. Stanley

Testing was conducted at the Energetic Materials Research and Testing Center for the MythBusters on three separate occasions. This testing included (1) an experiment designed to create diamond from graphite using the shock and pressure of a detonation, (2) the flattening of a car using a steel plate driven by a rocket sled, and (3) the bifurcation of a car also using a rocket sled. All tests were successful; diamond was produced following the detonation of ANFO, and extracted from a graphite / cobalt matrix. A plate was accelerated to 646 mph (1040 km/hr) using a two-stage sled system loaded with 5” (12.7 cm) high velocity aircraft rockets (HVAR) into a car, which was subsequently demolished. Finally, a steel wedge was pushed to 541 mph (871 km/hr) by a one stage sled using HVAR rockets, and was able to cleanly cut a target car in half.

Jan 1, 2010

By Marion Smith, Thomas M. Keevin, Dennis G. Wright, Gregory L. Hempen, Joel B. Gaspin, Thomas L. Linton, Gregg R. Gitschlag

"A Natural Resources Working Group, within the International Society of Explosives Engineers, reviewed published environmental effects data, identified data gaps, and prioritized data collection needs relative to underwater explosive use. Six groups of organisms were reviewed: 1) aquatic plants, 2) aquatic invertebrates, 3) fish, 4) amphibians, 5) reptiles, and 6) marine mammals. Studyrecommendations included: conducting basic research to determine the relationship between pressure waveform and mortality where little or no data exist (e.g., aquatic plants, fish, amphibians, reptiles, and marine mammals) and conducting narrowly defined studies where adequate data have been acquired (e.g., aquatic invertebrates). The goals of the recommended studies are to develop the relationship between pressure waveform and mortality/damage in order to construct mortality models. Development of comprehensive mortality models would be extremely useful to the blasting community for assessing environmental impacts and developing strategies for reducing impacts from explosives used underwater."

Jan 1, 1999

By Piyush Rai

Proper use of fi ring pattern vis-à-vis the blast requirements can provide optimal blast performance in terms of fragmentation. Further to this, each fi ring pattern has its own characteristic, for instance, although V-type and diagonal fi ring pattern provide same Se/Be ratio, the V-type fi ring pattern increases the opportunity for in-fl ight collision amongst broken rock fragments during their movement. Similarly straight V-type and skewed V type fi ring patterns (V1,V2 etc.) have their own characteristic strengths and weaknesses. In this light the present paper highlights the application of three different types of fi ring pattern on two different type of sandstone overburden benches of a large coalmine in India. The study reveals that Firing pattern infl uences the effective spacing to burden ratio at the time of detonation. By changing the fi ring pattern, effective burden (Be) changes and the ratio of effective spacing (Se) to effective burden (Be) during the fi ring is also subject to change in comparison to drilled spacing to burden ratio (S/B) Hence, the Se/Be ratio vis-à-vis fi ring pattern must be used to design the blast rounds. The results have been derived on the digital image analysis based fragment size characterization, excavator performance and evaluation of powder factor values on blasted muck piles. Skewed V- type fi ring yielded the best results in comparison to straight v-type and normally practiced diagonal fi ring pattern on the moderately strong sandstone benches, whereas, the existing diagonal fi ring pattern appears to be satisfactory on weak (weathered and gritty) sandstone benches. The presence of geological anomalies has also been investigated.

Jan 1, 2008

By Rob Grant, Manuel Lopez Cano, Mike Briggs, Ken Fletcher

The scorched desert sands and life giving waters of the River Nile in Egypt have been the back drop to awe inspiring engineering feats for over 4,700 years. The latest engineering marvel to grace the land of the Pharaohs is the Mubarak Pumping Station Project at Toshka. This ambitious project aims to open up an area of 607,000 hectares (1.5 million acres) of barren desert to irrigation based farming with the supply of 29 million tonnes (32 million tons) of water per day, drawn from Lake Nasser on the river Nile. It is anticipated that this currently unpopulated area of southern Egypt will soon flourish and become home to several million Egyptians who will conduct their lives around the water supplied by the 230 kilometers (144 miles) of concrete canals. An integral part of the pumping station is the intake canal. The canal was excavated in two sections – the dry excavation, and the wet excavation. The wet excavation comprised of some 5.5 million cubic meters (7.2 million cubic yards) of rock to be drilled, blasted, and excavated, from the surface of the lake. The challenge at hand was how to achieve this safely, quickly, and cost effectively, with water depths of up to 45 meters (148 feet), excavation depths of up to 47 meters (154 feet), blast production rate peaks of up to 30,000 bank cubic meters (39,200 bank cubic yards) per day, blistering summer air temperatures up to 60°C (140°F), and security concerns about the storage of large quantities of explosives in the Middle East region. The solutions to these challenges were engineered by UEE Explosives and centered around the use of a microgel bulk explosive called Rioflex™ and an international team of engineers and operators from three continents. The microgel and accompanying pumping system allowed pumping rates of up to 17,400 kg (38,400 lb) per day, and more importantly, enabled the bulk product to remain as an oxidizing matrix whilst in transport and storage, transforming into an explosive only moments before being pumped into the blastholes. This case study outlines the underwater drill and blast process employed at the Mubarak Pumping Station Project at Toshka, and the novel solutions to the unique challenges encountered.

Jan 1, 2004

By Virgil J. Stachura, Larry R. Fletcher

The Bureau of Mines conducted a series of delayed blasting experiments at a West Virginia contour coal mine which resulted in smoother highwalls. The highwalls were smoother due to reduced overbreak and inherently safer due to reduced likelihood of rockfall. Reduced overbreak was accomplished by an increase in the highwall hole delay intervals which changed the effective delay pattern geometry and the direction of burden movement. Three combinations of blast delay intervals in the highwall holes were tested: 1) 50 ms longer than the nominal design, 2) 50- and 100-ms longer delays in the nearest two rows that form the highwall, and 3) 100 ms longer than the nominal design. The mine's nominal blast design was a flat vee formed by 17-ms surface delays between holes and 42-ms surface delays between rows, with 200-ms in-the-hole delays. All three test designs produced highwall improvements over the nominal design with only occasional exceptions because of geologic variations.

Jan 1, 1985