Search Documents

By P. B. Altringer

Searles Lake, CA, contains the largest known domestic tungsten resource. The brines in this near-dry lake bed, located in the Mojave Desert 130 mi northeast of Los Angeles, contain an estimated 135 MMlb of tungsten. However, the low concentration of tungsten (0.080 g/L W03) in the supersaturated brine makes selective tungsten extraction very difficult. Although many brine chemicals are extracted from the lake, tungsten recovery was an elusive goal prior to Bureau of Mines development of an ion-exchange technique. This publication describes the Bureau process. The following subjects are ad-dressed: ? The Searles Lake tungsten resource. ? General problems associated with tungsten recovery. ? Bureau research objectives. ? Synthesis of ion-exchange resins. ? Development of a two-stage ion-exchange tungsten extraction and concentration procedure. ? Product recovery and purification. ? Economic evaluation. Flowsheets for recovering three products (calcium tungstate, sodium tungstate, and tungstic oxide) are presented and evaluated, as well as a summary of the research effort and potential applications.

Jan 1, 1985

By Michael Rieber

In this study a generalized specification and costing model for high tonnage coal carrying conveyor belts of 3.5 to 100 miles is presented. These belt systems, in modular units or flights, of up to 9 miles in length can be considered in terms of gathering systems. The study format is sufficiently open to allow users to insert their own requirements and parameters. A specific case study is provided. Because conveyor belts are feasible almost anywhere, this study has not investigated any specific route or geographic location. Rather, it has concentrated on setting up an heuristic programming model for conveyor belt facility optimization and cost minimization. The analysis starts with the principle factors involved in the design of the system and their optimization for various cases. This is followed, in Section 5.4, with a factor by factor cost analysis based on industry data and the preceding optimization. The next step is the development of both facility and costing models suitable for computer analysis. Logic flow diagrams are presented at each major analytic step.

Jan 1, 1977

By J. Walden, J. Rhoades, R. E. Miller, R. Gibbs, P. Boman

Accelerometers and pressure transducers, mounted in suspension components, can be used to monitor the ride of haulage trucks. Presently, it is difficult to tell what caused a jolt to the truck using either pressure or acceleration data alone. When information from a global positioning system (GPS) is recorded at the same time as shock pressures or acceleration data, the exact location of an event can be determined. Mine management can then determine what caused the jolt to the truck. This research is part of a National Institute for Occupational Safety and Health (NIOSH) project called "Engineering controls for reduction of jolting/jarring injuries in surface mines." NIOSH is investigating how the work environment of haulage truck drivers can be improved. The US Mine Safety and Health Administration (MSHA) notes that, between 1986 and 1995, 60% of the back injuries were to haulage truck drivers in metal/nonmetal surface mining. Personnel from Phelps Dodge suggested that combining acceleration data with information obtained from a GPS could generate results with a variety of uses. Therefore, researchers at the Spokane Research Laboratory (SRL) began investigating how to tie acceleration and GPS data together. It was originally thought that this tool would be used primarily for road and truck maintenance. However, as research progressed, it became apparent that it would also be useful in providing feedback about equipment operations and identifying unusual causes of jolting. Experimental approach Available components that function well by themselves were linked for the purpose of proof of concept. Using a Modular Mining Systems (MMS) product called Vital Signs, SRL researchers took an Aero-Marine Products (AMP) acceleration recorder and hardwired it to MMS Dispatch equipment already installed on a truck. AMP is one of several manufacturers of acceleration recorders frequently used to monitor freight during shipping. MMS Dispatch is used for production accounting and truck dispatching and uses GPS tracking. Through Vital Signs, an analog or digital alarm signal can be recorded. Steve Rhoades, of MMS, wrote unique code that links the Vitals Signs data and GPS location and stores this data in an ASCII log file. SRL researchers installed the equipment in a Caterpillar 793 haul truck. The result was a working prototype. Figures 1 and 2 show the instrument installation in the truck. Discussion From 8:30 pm on Sept. 14, 1998 until 6:50 am on Sept. 15 1998, 899 jolts above a threshold of 2 g (1 g is the acceleration of gravity. It is either 9.81 m/s2 or 32.17 ft/ s2.) were measured on the test truck. Some sections of the haulage road produced most of the events, while

NIOSH research has focused on the monitoring and the control of methane levels in active mine workings. Response times for instrumentation using catalytic heat-of-combustion sensor technology were evaluated. NIOSH research has modelled the flow of methane gas onto long-wall faces and gobs, developed engineering controls to limit methane levels during mining, and designed coalbed and gob degasification systems. Available methane control systems have been challenged by recent developments in longwall and room-and-pillar mining systems. This includes increased face advance rates leading to increased productivities, increased longwall panel sizes, and the generally deeper workings of U.S. coal mines. The potentially violent nature of any underground explosion or ignition requires the measurement, control, and reduction of methane emissions into the mine environment for continued worker safety.

Jan 1, 2008

Reduce the cost of modifying uranium well casings so that leaching solutions can pass through, but sand grains are blocked. Approach The well casing and surrounding cement are perforated at the mineralized zone by impinging them with high pressure water jets. How It Works A nozzle assembly is attached to a high pressure (15,000 psi) pipe and lowered into the well casing which typically is schedule 40 PVC (poly-vinyl chloride). The high pressure pipe line is extended down Into the casing until it reaches the mineralized zone. The upper end of the pipeline is then connected by a high pressure hose to the outlet of a 10,000 psi pump. Turning the pump on for 5 seconds causes a high velocity water jet to cut through the well casing and the surrounding cement. Figure 1 shows a high pressure pipe being installed in a well casing. Cutting small diameter holes in the casing allows the leachant to enter the casing and be pumped to the surface. However, the holes are small enough to prevent most sand grains from entering. Numerous holes are usually cut through the casing. The 3-nozzle assembly shown in Figure 2 cuts three holes, one above another.

Jan 1, 1978

By D. J. Bauer

Oxidation of mixed lanthanide solutions with ozone at pH 4.5 and at ambient temperature resulted in precipitation of 98 percent of the original cerium present. Corresponding cerium purity was increased from 50 to 98 percent. A second ozone oxidation-precipitation step produced cerium of 99.9 percent purity in high yield from the 98-percent-pure material. Alternately, ozonation at pH 6.5 and 85° C differentially precipitated cerium and rare-earth elements heavier than cerium and left 89 percent of the original lanthanum in solution at a purity of 95 percent. Subsequent recovery of cerium from the heavier rare-earth elements in the precipitate was accomplished by dissolving the precipitate in dilute mineral acid and reoxidizing the cerium with ozone at pH 4.5 and at ambient temperature. The filtrate contained an enriched praseodymium-neodymium-samarium-europium mixture that is amenable to separation by ion exchange or solvent extraction.

Jan 1, 1968

By Thomas M. Barczak

The initial Support Technology Optimization Program (STOP),Version 1.0, was released at the 19th Ground Control Conference. This original program has since been updated to Version 2.3 which was released in May, 2001. This paper describes the additional features of Version 2.3, focusing primarily on the following three aspects: (1) including uncontrolled convergence into the design requirements for standing roof supports, (2) the addition of design procedures for cable bolts as an alternative secondary roof support, and (3) the addition of new standing roof support technologies. Another new feature which should facilitate the development of design criteria for standing roof support is the capability to define ground reaction curves through convergence measurements alone without having to make support loading measurements. There are several other new features provided in Version 2.3 which are only briefly addressed in the paper. These include: (1) additional graphics capabilities to facilitate rapid assessment of support comparisons, (2)an East-West designation for support selection to more accurately provide cost and support availability data, (3) additional safety measures including a safety factor to identify support design near the peak support capacity, checks to see if the support dimensions comply with aspect ratio requirements, and a measure of roof coverage for the design layout of the support system. These new features of STOP provide more capabilities to design and analyze secondary roof support systems for conditions which could not be fully analyzed in the original version of the program.

[ ]

Jan 1, 1981

By Eric E. Cather

A mineral survey of a portion of the Lake Eleanor RARE II area (No. 5807), Trinity County, California, was done by the U.S. Bureau of Mines and U.S. Geological Survey (USGS). Approximately 8,650 acres (3,500 ha) of the Lake Eleanor RARE II area not examined for this report had been previously investigated by U.S. Bureau of Mines and U.S. Geological Survey personnel and published as part of USGS Bulletin 1371-B, (Hotz, 1972) Mineral Resources of the Salmon-Trinity Alps Primitive Area, California. The report showed that the section included in the rake Eleanor RARE II area contained no metallic mineral resources. Geochemical sampling indicated that the Lake Eleanor RARE II area contains no potentially important mineral resources. About 4,650 acres (1,880 ha) of the eastern part of Lake Eleanor RARE II area were examined for this report. The Bureau of Mines was responsible for detailed examination and sampling of mines, prospects, and mineralized zones; the Geological Survey conducted geological, geochemical, and geophysical studies of the area. This area is underlain mainly by granitic rock and serpentinite.

Jan 1, 1981

By H. S. Kennedy

THE HELIUM ACT (50 Stat. 885; 50 U. S. C. 161,163-166), as amended, places the responsibility for conserving, producing, and selling helium upon the Secretary of the Interior, acting through the Bureau of Mines-the only producer of helium in quantity in the world. It operates 4 plants-I each at Amarillo and Exell, Tex.; Otis, Kans.; and Navajo (Shiprock), N. Mex. The demand for helium has increased steadily since the decline immediately after World War II and is expected to exceed the capacity of the present plants in the near future. The Congress has appropriated $6,000,000 far constructing a new plant. In addition to providing additional capacity to meet increased demands for helium, the new plant will enable the Bureau of Mines to better conserve the helium in, the Government-owned reserves at Amarillo and Navajo.

Jan 1, 1958

By Milford L. Skow

This report summarizes the principal activities and results of 15 years of research by the Bureau of Mines, U.S. Department of the Interior, on methane control in coal mines. This research has investigated fundamental factors regarding the occurrence and movement of methane in coal beds, removal of methane prior to mining, and control of methane during mining. The report includes a bibliography listing the more than 150 publications resulting from the Bureau's methane control program as well as numerous other references, a section on methane recovery and use, a look at the upcoming Bureau of Mines research program, and a brief review of methane drainage practices in other coal-producing countries.

Jan 1, 1980

By Sheridan J. Rodgers

Toxic fumes generated during shot firing were measured in a phosphate rock mine and a copper mine. Fumes generated during firing of explosives in the Bureau of Mines 1350 ft3 test chamber were measured also. The release of fumes from water gels, ammonium-nitrate oil mixtures and nitroglycerin based explosives was studied. Direct reading instruments were used to monitor the fume concentrations. The amount of CO produced per unit weight of nitroglycerin explosives (0.41 ft3/200 grams) was higher than that produced by ammoniumnitrate-oil mixtures (0.24 ft3/200 grams) and water gels (0.16 ft3/200 grams). The amount of NOx produced by nitroglycerin based explosives was also higher than the amount produced by water gels or ammonium nitrate-oil mixtures.

Jan 1, 1976

This study was conducted to determine the effects of a machine-mounted scrubber and water sprays on face methane levels. Testing was conducted in the NIOSH ventilation test gallery which was designed to simulate a full-scale mine entry. In the test entry, a model mining machine, equipped with water sprays and a simulated dust scrubber, was located at the face of a 20-ft box cut. Blowing ventilation was provided using a curtain with a 40-ft setback distance. Methane released from a pipe manifold located inby the mining machine was monitored at six locations that were 1 ft outby the pipe manifold. Tests were first conducted to evaluate the effects of using sprays and scrubber separately on face methane levels. Additional tests were conducted to determine how a scrubber used with various water spray systems would affect face methane levels. The use of either sprays or scrubber reduced face methane levels significantly. The combined use of sprays with the scrubber further reduced face methane levels a small amount. Primarily the sprays affected methane levels by changing airflow distribution close to the face.

By Stephen C. Tadolini, Thomas M. Barczak

A critical safety component for all underground mining is intrinsic and standing support systems. Specifically, tabular hardrock mining exploits a wide variety of deposits that require various methodologies to safely mine the ore material. Several new support systems have been developed in recent years for hard rock applications which have been modified or applied in a variety of ground control applications. These include prestressing devices, improved cribs, and free standing supports. Various standing support and prop-type systems have been designed for hardrock applications with seismic loading conditions to accept prestressing. The prestressing, using water-filled cells, creates an active load upon installation and is considered essential to maintain support during and after the blasting of the mine faces. Heavy seismic activity is also present in these mines and the prestressing units can provide some energy absorption capability to help preserve the integrity of the support. This paper presents an overview of these innovations in support technology.

By M. Kanefsky

Two channel polarity coincidence and polarity difference statistics are analyzed. The signal, common to both channels, consists of sinusoidal bursts where the exact frequency of the signal is nearly known, but other parameters such as amplitude, phase, and pulse starting time are unknown. The noise inputs are dependent, narrow band, Markov processes. It is shown that the performance depends not only on the signal uncertainties, but on the precise shape of the cross-correlation functions between the noise in-puts. By using two polairty difference statistics in addition to the polarity coincidence statistic, it is shown that the decrease in performance, as well as the cost of hard limiting due to correlated inputs, can be made small.

Jan 1, 1981

The Anaconda Copper Company reportedly reached an exclusive agreement with Cook Inlet Region, Inc., to explore 24 million acres in south-central Alaska and to share equally with Cook the proceeds of any mineral discovery. According to an Anaconda geologist, "the company is anticipating, based on geologic testing, that it will find significant deposits of copper, lead, and zinc. There is also evidence of the presence of precious metals such as silver and gold, and also strong evidence of strategic minerals such as chrome, platinum, tin, and nickel." Cook Inlet Region, Inc., is owned by 6,500 Alaskan natives. Chile, which has a growing, free-market economy under President Pinochet, reportedly will no longer require companies to obtain prior governmental approval for the exploration and development of new mines.

Jan 1, 1981

In 2001, 14,623 mining operations reported employment statistics to the Mine Safety and Health Administration (MSHA). This was an increase of 210 mining operations compared to 2000. Almost half (49%) were sand and gravel mines, followed by stone (29%), coal (15%), nonmetal mines (5%), and metal mines (2%).

May 1, 2003

By R. J. Tocher

Uniaxial testing was performed on coal specimens to determine the time-dependent response. The testing was carried out on coal from six mine sites throughout the Western United States and Pennsylvania. Testing configurations were varied to allow analysis of moisture dependency, stress level and specimen orientation. Several theories were presented for the behavior of coal due to moisture diffusion. Experimental results showed the correlation between the theories and the actual material response. Coal deformation was found to be highly dependent on the moisture level of the testing environment. Moisture migration causes drying and shrinkage which lead to progressive degradation of the material. The coal tested experienced a rebound if saturated after a period of drying. This type of time-dependent behavior overshadows the dependence on the applied stress level, which, however, still produces a noticeable creep behavior. Analysis of one series of creep test results was performed. A relationship was developed on the basis of a simplified rheological model to describe the coal response to uniaxial stress. Previous empirical formulations in the form of power laws were compared and their deficiencies pointed out.

Jan 1, 1980

By Forrest T. Moyer

THIS CHAPTER of the Minerals Yearbook contains injury experience and related employment information for the coal-mining, coking, oil and gas, peat, and native asphalt industries in the United States for 1963. No attempt has been made to combine these data and present injury-frequency rates reflecting the mineral-fuel industries because the hazards of the separate industries are not comparable. Tabulations showing the trend of injuries and employment for all mineral industries are presented in Volume III of the Minerals Yearbook. COAL Injury experience of the coal-mining industry was improved slightly in 1963, as measured by the 2-percent decline in the Injury-frequency rate. Although the total number of fatal and nonfatal injuries increased 1 percent, the greater proportional increase of 3 percent in man-hours worked accounted for the improved frequency rate. Employment and injury data for 1963 are based on final data for anthracite mines and preliminary data for bituminous coal and lignite mines.

Jan 1, 1964

By R. G. Bottge

To better understand those factors which increase mining costs in Alaska, a Bureau of Mines study was conducted to compare the estimated costs of operating a 100,000-tpd open pit copper mine located on a hypothetical ore body in the Lake Clark area, Alaska, with the costs of mining a similarly sized hypothetical copper ore body near Tucson, Ariz. The information derived should be beneficial to the State and Federal governments in appraising the potential for development of large, low-grade porphyry copper deposits in south-central Alaska. Conventional mining and concentrating methods were assumed, and capital and operating costs were derived using flowsheets and standard costing methods. The total price required for copper mined in Alaska and Arizona was $1.12 and $0.63 per pound, respectively, plus or minus 20 percent. These values were obtained assuming no leaching of low-grade copper, recovery of gold, silver, and molybdenum as byproducts, 100-percent equity financing, and a 12 percent discounted cash flow rate of return. The average domestic and international prices for copper in July 1973 were $0.60 and $0.916 per pound, respectively. The existence of a developed transportation and power system in Alaska would have reduced capital and operating costs subs tantially. The required price for copper would have declined from $1.12 to $1.05 per pound, plus or minus 20 percent.

Jan 1, 1974