Search Documents

By Fred N. Kissell

In This Chapter [The explosibility of methane gas mixtures Effect of pressure and temperature on explosibility Less common sources of methane ignitions The amount of methane stored in coal Forecasting the methane emission rate Layering of methane at the mine roof When the recirculation of mine air is hazardous The importance of higher air velocity in preventing methane explosions and Mine explosions, barometric pressure, and the seasonal trend in explosions] Dealing with methane in mines and tunnels requires knowledge of the circumstances under which dangerous accumulations of methane are likely to occur. This knowledge involves the properties of the gas itself, an awareness of where these accumulations are likely to occur, and facts on how methane mixes safely into the mine air. The other chapters in this handbook address the handling of methane under a variety of specific circumstances, such as at continuous miner faces or coal storage silos. This chapter addresses some broad concepts that serve as a foundation for the suggestions provided in other chapters. THE EXPLOSIBILITY OF METHANE GAS MIXTURES Methane entering a mine or tunnel often enters as a localized source at high concentration. Figure 1–1 depicts a cloud of methane being diluted into a moving air stream. In this illustration, methane enters the mine from a crack in the roof. As the methane emerges from the crack, it progressively mixes with the ventilation air and is diluted. In the event that this progressive dilution reduces the concentration from 100% to 1%,2 as shown in Figure 1–1, the methane passes through a concentration range of 15% to 5%, known as the explosive range. In the explosive range, the mixture may be ignited. Above 15%, called the upper explosive limit (UEL), methane-air mixtures are not explosive, but will become explosive when mixed with more air.

Jan 6, 2006

By David A. Lipton

In 1980, the U.S. Bureau of Mines conducted a mineral survey of the 23,500 acre Garcia Mountain RARE II area (No. 5107) in the Los Padres National Forest. Bureau of Mines data indicate a low potential fur gold, silver, and mercury resources. Twenty-nine placer samples, representative of small yardages, showed small amounts of gold or other economic mineral values. Mercury deposits in faulted siliceous rocks in the Franciscan Formation occur north of the area. Similar rocks are in the southwest part of the study area, but apparently contain no mercury deposits. Geothermal and oil and gas potential is low.

Jan 1, 1982

This summary of State laws on explosives wag compiled primarily to ascertain what subjects relating to their control have been acted upon by each State legislature and, in general, how they have been treated. It does not Include any legislation passed after 1942, or any proclamations, regulations, or administrative orders. It does not purport or attempt to be authoritative. If any problem arises involving interpretation of the statutes of any particular State, the original source must be consulted for the exact words used by the legislature. This summary, however, will be useful in determining whether relevant statutes exist, and in locating them quickly, with a minimum of effort. It will be of value also in comparing statutes in other States to determine what construction has been placed upon them by the courts of these jurisdictions or to contrast the varying provisions of many States upon a similar subject. To make these comparisons easier, the statutory provisions for each State have been grouped under several major topics in outline form. Although this sometimes has resulted in disruption of the continuity of individual acts, the increased general clarity and availability of comparable sections have more than justified the procedure followed.

Jan 1, 1943

By G. G. Huggins

A demonstration project has been completed to reduce the operator sound level of an underground service vehicle, a personnel dispatch wagon, to go dB(A) or less. The program objective was to implement quieting recommendations made on an earlier study for the USBM n diesel-powered mine equipment. The manufacturer and mine to which the vehicle was going actively participated in the program to ensure a product that was not only quiet, but useful. The key element of the quieting package is an engine part a1 enclosure, which, with several complementary noise control components, reduced the operator sound level 14 dB, from 101 dB(A) to 87 dB(A). The vehicle underwent a 4-month trial period, with no degradation in the quieting package. Mine personnel reported no maintenance difficulties, and were enthusiastic about the dispatch.

Jan 1, 1975

By E. D. Gardner

This paper is the third of a series of three on placer mining in the western United States. The first paper4 discusses the history of placer mining in the Western States and the production of placer gold, geology of placer deposits, location of placer claims on public lands, sampling and estimation of gold placers, and classification of placer-mining methods, together with hand-shoveling and ground-sluicing. The second papers deals with hydraulicking, sluice boxes and riffles, recovery of gold and platinum from placer concentrates, treatment of amalgam, and marketing of placer gold. The discussion of sluice boxes and subsequent subjects in the second paper applies to all forms of placer mining. The present paper treats of dredging and other forms of mechanical handling of placer gravels, and drift mining.

Jan 1, 1934

By Steven E. Mischler, Jon C. Volkwein

A diesel particulate matter analyzer capable of direct, real-time measurement of engine exhaust particulate is necessary to effectively institute source control technology currently being used on diesel equipment and to ensure that the control measures are working. To investigate the potential of a differential pressure monitor to measure diesel particulate matter in undiluted exhaust, samples were collected from three different diesel engines-Kubota, Isuzu, and Deutz-running under 12 different RPM and load scenarios. These measurements were compared to elemental carbon concentrations in the sampled exhaust as determined by using the NIOSH 5040 analytical method. Elemental carbon is used as a surrogate measurement for diesel particulate matter. The results of the two data sets were then compared using a linear regression analysis. The coefficient of determination (or R2) was calculated to be 0.98, 0.94, and 0.74 for the Kubota, Deutz, and Isuzu engines, respectively. R2 values of this magnitude indicate that this method can be successful in estimating elemental carbon emissions in the engines tested. In addition, for replicate samples, the coefficient of variation ranged from 7.1% to 10.2% with an average of 8.5%. These data indicate that this method could prove useful to mechanics as they work to maintain engines and DPM control technologies.

By Donald O. Capstick

A mineral resource evaluation of the Coyote-Southeast RARE II area (No. 5033) was performed jointly by the U.S. Bureau of Mines and the U.S. Geological Survey in 1981 for the U.S. Forest Service RARE II program. Bureau of Mines personnel conducted a mineral resource inventory of the study area's mines, prospects, claims, and mineralized outcrops. The study area's boundaries encompass 51,700 acres on the east flank of the Sierra Nevada and are within Inyo National Forest southeast of the city of Bishop in east-central California. Cretaceous granite underlies most of the area; the remainder of the rocks are metasedimentary. At the contact of the two, tactites formed at many places where carbonate rocks were present; replacement processes produced local scheelite (calcium tungstate) occurrences.

Jan 1, 1983

By Yumi Nakashima, Setsuo Maeda

Vibration magnitude and frequency of the z-axis vehicle seat are time-variant, which are influenced by not only vehicle vibration characteristics themselves but also road surfaces, speeds and the human body. There is little in the current reporting about evaluating and analyzing automobile seat vibration that focuses on the time-variant. Yaguchi et al.1 has proposed a method to evaluate automobile seat vibration that is based on judgments using a subjective mental state. Their method focuses on the time-variant magnitude of the peak frequency on a power spectrum density. However, their method has no consideration of all the frequency contents of the discomfort, nor comparison between different peak frequency vibrations. Suzuki2 has emphasized that the vehicle vibration should be judged by a series of vibration stimuli to evaluate, because the vehicle vibration is time-variant, which isn’t a matter of the relationship between a single vibration stimulus and a subjective response. He clarified that the human sensation to the vehicle vibration discomfort changes every moment showing the relationship between the frequency-weighted r.m.s. acceleration calculated every 5 seconds and the category judgment to vehicle vibration discomfort every 5 seconds. However, his study doesn’t show what parameter connects to the subjective final judgment to vehicle vibration. Therefore, we applied the method similar to ISO100563 considering the time-variant to the vehicle seat z-axis vibration evaluation. The new method for the vehicle seat vibration considering the time-variant was examined on the hypothesis that the final subjective evaluation must be conducted from the judgment summarizing a series of vibration stimuli. Methods The vibration bench system, which reproduces the movement of a vehicle floor, was used for the experiment with the single-axis (vertical direction) four-post road simulator system, which is usually used for a car, as shown in Fig.1. The experiment was done on the right side of the vibration bench using the floor vibration which was 5.5 minutes, 0.822 m/sec2 (Wk) over the range 0.5-20Hz with 4 male subjects (age ave21.5, SD0.5, weight ave75kg, SD7.91kg, height ave166.8cm, SD5.2cm) and 4 suspension seats. As Fig.2 shows, subjects evaluated the degree of discomfort every 5 seconds to each seat vibration measuring the seat z-axis vibration acceleration. [ ]

Jan 6, 2006

By E. A. Barrett

The U.S. Bureau of Mines (USBM) conducted experiments to determine if training using a latent-image, three-dimensional (3-D) slide simulation exercise improved miners' ability to recognize roof and rib hazards. The effectiveness of this innovative type of classroom training was investigated by measuring workers' performance on a hazard recognition task. The study was unique in that hazard recognition skills were assessed in the workplace using actual coal mine roof and rib hazards. Results showed that training with a latent-image, 3-D slide simulation exercise significantly improved each subject's performance on the in-mine hazard recognition task. Further, the USBM researchers concluded that transfer of learning from the classroom to the workplace occurred.

Jan 1, 2010

By Staff

A major emphasis of the U.S. Bureau of Mines is to perform research on the prevention of fatal accidents at mining operations. The leading cause of fatalities in the underground coal mining industry is groundfalls. This proceedings volume presents several new developments that are helping to prevent fatalities and reduce injuries by groundfalls. The papers focus on the problem from two different perspectives. About half of the papers present information and techniques that can be used to train and motivate miners to protect themselves from groundfalls. The other papers explain how to identify and respond to various geologic conditions that affect the stability of the mine roof. Of the 95 groundfall fatalities that occurred during 1986-90, 75% took place in Kentucky, West Virginia, and Virginia. The rate of groundfall fatalities was much higher at small mines. During 1986-90, the rate of groundfall fatalities at mines employing fewer than 20 people was 4.3 times higher than the rate for larger mines. Because so many groundfall fatalities are occurring at relatively small mines in the southern Appalachian coalfields, many of the papers focus specifically on the needs of this category of mine operations.

Jan 1, 1992

The revised inspection standards or recommendations herein have been prepared for use in Federal inspection of bituminous-coal and lignite mines. They succeed a compilation of similar standards published as Bureau of Mines Information Circular 7268 in December 1943 and employed as a guide in Federal inspections since that time. Important alterations and additions have been made because of changes in mining, practice and temporary shortages of some safety equipment; moreover, several previous standards have been found not generally applicable and have accordingly been deleted. Mining methods and equipment continue to change, and new hazards and new safeguards are introduced. Consequently, these standards are subject to revision from time to time. Questions from the coal-mining industry regarding these standards and suggestions as to changes and additions thereto will be welcomed and considered carefully when the next revision is made. Many constructive criticisms from the mining industry have been considered in preparing this edition.

Jan 1, 1945

By Ronald P. Hollenbeck

The value of mineral production in Alabama reached a new high of more than $246 million. 4 percent above the previous record established in 1964. New high values were reported for bentonite, portland cement, fire day, kaolin, miscellaneous clay, lime, crushed limestone, crushed marble, mica. salt, and sand and gravel. Among the States, Alabama ranked second in the production of bauxite and scrap mica and third in the production of native asphalt. The mineral industry of Alabama was dominated by the mining and processing of coal and Slone, the manufacturing of cement, and the production of crude petroleum, which together comprised 85 percent of the total value of mineral output, compared with 84 percent in 1964. The iron ore industry continued to decline. Coal production continued to increase, resulting in the State's coal-mining best year since 1948.

Jan 1, 1967

By J. E. Chilton

The National Institute for Occupational Safety and Health (NIOSH) has conducted research to determine the influence of mining machine-mounted scrubbers on airflows and methane concentrations at the face when blowing ventilation systems are used. Tests were conducted in a full-scale ventilation gallery with a model mining machine that simulated airflow created by a dust scrubber. During the tests, ultrasonic anemometers were used to measure airflow speed and direction at several locations near the face. For the same test conditions, methane was released from the face and gas concentrations were measured at 21 locations above the machine using fixed point methanometers. Changes in airflow speed and direction are correlated with scrubber airflow and the measured methane distribution above the mining machine. The research results showed that operation of machine-mounted scrubbers improved face ventilation when blowing ventilation is used by increasing both the intake flow and the quantity of air reaching the face.

By Charles G. Maier

"INTRODUCTION The use of thermodynamic calculations to answer practical problems in metallurgy, especially those that are relatively difficult to test experimentally, is rapidly becoming a conventional method of procedure. Nevertheless, these methods cannot he applied effectively until the fundamental thermodynamic constants used for them have become available either by direct experiment or by recalculation of data already existing in more or less undigested form.In an attempt to collect such data far the compounds of lead and the antimony group the incentive has been to make a preliminary survey that will disclose the gaps or questionable phases of available information and to collect data that may be used to answer certain rather practical problems presented by operating metallurgists.This report comprises three sections; the first gives the basis of selection of the constants which may now be given or estimated, and the later sections discuss the application of the figures obtained to two of the more interesting problems.The reader will discover that many of the quantities involve critical study of a number of more or less discordant observations. Although certain data could be rejected on the basis of thermodynamic comparisons, it must not be overlooked that many of the figures are the results of rational estimates rather than exact experiment. The use of thermodynamic methods to control and partly authenticate such estimates is one of its most valuable characteristics for the practising metallurgist or chemist, who cannot check by direct experiment each property of the materials which he converts to usable form.Nevertheless, while it is definitely possible in certain instances that the final figure selected for the heat or free energy of a process or substance may be in error by as much as a few hundred to a few thousand calories per formula weight, questionable figures are usually revealed by the thermodynamic calculations made. When quantities of such degree of accuracy are, and they often must be, used for estimating an unknown reaction, the result often gives no more than the order of magnitude of the desired quantities. Yet even in these extreme cases the answer is far more reliable and valuable than an unordered guess or a conclusion based on incorrect data."

Dec 1, 1934

By Steven J. Page

Researchers have developed a model to describe airborne respirable dust (ARD) generation on surface coal mine drills. By measuring a few basic parameters and using a graph, a drill operator or engi­neer can estimate the relative severity of drill dust emissions as well as how much of a reduction in ARD can be obtained by changing any given parameter. Geometric parameters include: drill deck cross-sectional area, shroud leakage associated with the deck shroud as well as the operational parameters of bailing air­flow, and dust collector airflow. The rela­tionships yield predictive ARD values which fall in the range measured on oper­ating drills for collector/bailing air flow ratios greater than 2. Overexposure to airborne respirable crystalline silica dust can cause serious or fatal respiratory disease. Exposures of sur­face coal mine rock drillers to respirable crystalline silica are of particular concern. In a 1992 alert on silicosis in rock drillers, the National Institute for Occupational Safety and Health (NIOSH) reported on 23 cases of advanced silicosis (acute, acceler­ated, and chronic) ranging in ages from 25 to 60 with drilling tenures ranging between three and 20 years.1 Most of the cases involved drill operators in their 30?s and 40?s, indicating high silica exposure levels are associated with their occupation. A more recent lung x-ray surveillance study of a 664 volunteer population of surface coal miners showed that the prevalence of silicosis-like abnormalities was 9%.2 The two most significant factors associated with these abnormalities were increasing age and years of drilling experience.

Jan 1, 2008

By Ronald B. Stotelmeyer

This report summarizes the U.S. Bureau of Mines evaluation of the mineral resources of eight roadless areas in several National Forests in Montana. The areas are amoung those that have been proposed as additions to the National Wilderness Presevation System In various sessions of the U.S. Congress. Mineral Commodities present include gold (lode and placer), silver, copper, lead, zinc, molybdenum, tungsten, rare-earth elements, fluorite, and barite. Numerous mineral deposit types occur. Past production was from gold placers and vein-type deposits. There is potential for development of large volume porphyry copper-molybdenum, disseminated gold, stratabound copper-silver, and exhalative massive-sulfide metallic deposits. A substantial increase in metal prices is needed before any known vein-type deposits will be economic.

Jan 1, 1994

By Dean H. Ambrose

This paper presents the results of a study using computer human modeling to examine machine appendage speed. The objective was to determine the impact of roof bolter machine appendage speed on the likelihood of the operator coming in contact with. A contact means two or more objects intersecting or touching each other, e.g., appendage makes contact with the operator?s hand, arm, head or leg. Incident investigation reports do not usually contain enough information to aid in studying this problem and laboratory experiments with human subjects are also not feasible because of safety and ethical issues. As an alternative, researchers developed a computer model approach as the primary means to gather data. By simulating an operator?s random behavior and machine?s appendage velocity, researchers can study potential hazards of tasks where it is not possible to perform experiments with human subjects. Analysis information is helpful to the mining industry in terms of making recommendations that reduce the likelihood that roof-bolter operators experience injury due to contact with a moving boom. Data analysis of roof bolter simulations show that the virtual-operator?s response time has little effect on the number of contacts experienced. Based on frequency and cross-tabulation, regardless of other variables, contact incidents were always greater when the boom was moving up, were always greater on the palm, and were always greater for the boom part of the machine. Also, regardless of boom speed, the 25th-percentile-sized operators experienced more contacts than did other operator sizes. Furthermore, regardless of boom speed, the 152-cm mine seam experienced more contacts than did other seam heights tested. Results of a survival analytic approach suggest that controlling the boom speed is the most important factor in determining the risk of an operator making contact. Based on the data collected, boom speed greater than 41 cm/s results in a substantial increase in risk to the roof bolter operator and should probably be avoided. At speeds less than or equal to 25 cm/s are associated with a more modest relative risk, which represents an acceptable level of risk. Also, at speeds between 25 and 41 cm/s, there could be a particular boom speed in this range at which a significant inflection point in the relative risk estimates occurs. Based on the results, this issue needs to be addressed by future research.

Jan 1, 2003

"Requests are frequently received by the Information Service of the Bureau of Mines for published information on the coals of different foreign countries, as compared with coals mined in the United States. The analyses of various coals from several countries on the Pacific, which were submitted to the Fuels Division for certain tests between the years 1913 and 1916, may be of interest, and are shown below: Results of Analyses of Various Coals from China, New Zealand, Japan and Australia."

Sep 1, 1925

By C. W. Elder

"INTRODUCTION This report describes a method of horizontal drilling in an oil-producing formation underlying a 400-acre, approximately square plot of land in the Franklin Heavy oil field in Sugar Creek Township, Venango County, Pa. The method, which was developed on two previous projects in Ohio, 3/ consists of sinking a shaft to the bottom of a shallow oil sand and drilling holes in a general horizontal plane outward from the chamber in a pattern similar to that of the spokes of a wheel. The project was undertaken by the Venango Development Corporation in an attempt to find an efficient method of recovering oil from partly depleted sand formations.The Venango Development Corporation is composed of the following oil-producing and oil-refining companies and individuals: South Penn Oil Co., Forest Oil Corporation, Kendall Refining Co., Minard Run Oil Co., Quaker State Oil Refining Co., The Pennzoil Co., Alliance Oil Corpo¬ration, United Refining Co., Franklin Creek Refining Corporation, Canfield Oil Co., Pennsylvania Refining Co., Page Oil Co., Freedom Oil Co., D. W. and D. S. Grant, and J. P. Herrick, C. M. Davison and N. V. V. Franchot. Engineering features of the project were supervised by a committee off three engineers A. J. Saxe, chairman, W. M. Shoemaker, and C. N. Pfohl, who supervised the excavation of the shaft and the drilling of the first two holes by alternately spending a week at a. time at the project. The drilling method was under patent license from Leo Ranney, who served as technical advisor to the Venango Development Corporation; in addition, he furnished the design for the shaft and work chamber."

Sep 1, 1944

By J. R. Thoenen

In Progress Rerort 1,4/ a number of facto were demonstrated and conclusions drawn from experimental tests and records made during commercial blasting operations at a number of quarries. For example, the tests showed (1) that vibrations received on outcrops were of comparatively

Jan 1, 1938