Search Documents

By Douglas F. Scott

Zinc, silver, copper, and tungsten are the principal minerals in Dardanelles RARE II area (No. 4982). Zinc with associated silver and copper occurs in a persistent shear zone in metasedimentary rocks and in a massive sulfide vein; tungsten occurs as disseminated scheelite in a tactite zone along a metasedimentary-intrusive rock contact. Since 1883, approximately 100 lode mining claims have been recorded, mainly it the eastern portion of area No. 4982 (fig. 1). Extensive workings on the Alhambra Prospect indicate past production; however, no records were found for the prospect. At the Alpine Mine, 500 tons of tungsten ore had been mined before 1943 (Hopson, 1943, p. 1) and possibly 1,000 tons of tungsten ore mined by 1947 (Benson, 194/, pp. 2).

Jan 1, 1982

By C. L. Karr

Researchers at the U.S. Bureau of Mines (USBM) have developed adaptive process control systems in which genetic algorithms (GA's) are used to augment fuzzy logic controllers (FLC's). GA's are search algorithms that rapidly locate near-optimum solutions to a wide spectrum of problems by loosely modeling the search procedures of natural genetics. FLC's are rule-based systems that efficiently manipulate a problem environment by modeling the "rule-of-thumb" strategy used in human decision-making. Together, GA's and FLC's include all of the capabilities necessary to produce powerful, efficient, and robust adaptive control systems. To perform efficiently, such control systems require a control element to manipulate the problem environment, an analysis element to recognize changes in the problem environment, and an adaptive element to adjust to the changes in the problem environment. The control system also employs a computer simulation of the problem environment. Details of an overall adaptive control system are discussed. A specific laboratory acid-base pH system is used to demonstrate the ideas presented; all results are from the physical laboratory system and not from a computer simulation.

Jan 1, 2010

By John C. Machisak

The Nation's mining and quarrying industries have again met the annual challenge to their ingenuity--that of reducing disabling work injuries among their employees. The effectiveness of management in facing this problem and in meeting this responsibility from the results of the 1961 National Safety Competition. Three hundred ninety-three or 45.3 percent of the mines and quarries participating in the competition established a new record number of participants operating throughout the competition year without a disabling work injury. Another record established in the 1961 contest was the number of participants (868) enrolled in the competition. This annual safety competition was begun in 1925 and is conducted by the Bureau of Mines, U.S. Department of the Interior. It provides for six bronze Sentinels of safety trophies which are awarded each year to the winning participant in each group. Since its inception, the competition has exerted a strong influence in the field of safety promotion. The statistical record of its accomplishments over the years gives strong support to the theory that well-organized and well-administered safety programs are effective tools to be used to reduce the number of disabling work injuries. It stimulates and holds the interest of employees and management in accident prevention. Because of this, mines and quarries participating in the contest have a more favorable safety record than those operations not enrolled.

Jan 1, 1963

By J. D. Clendenin

Systematic practices for protecting crops from frost damage began in the United Metes more then 40 years ago when the Weather Bureau Fruit-Frost Warning Service was organized; however, various practices employed in frost protection are centuries old. Although there are areas where little doubt exists as to whether protection is needed, there are also circumstances where there is some doubt as to the need for frost protection. Many factors influence this, including not only critical temperatures but also the maturity dates of the crops relative to marketing. Critical temperatures for frost damage to trees, plants, blossoms, and fruits very with weather, plant variety and nutrition, and stage of growth. In the case of truck crops, a single night of protection from frost injury might yield big dividends with a variety of sweet corn or tomato that matures early while price is high yet be worth very little with a midseason or late-maturing variety. Consequently, it is the individual grower who must decide whether to use frost-protective measures on the basis of his returns, the quantity and quality of his crop, the marketing situation, the sensitivity of his crops to frost damage, and the frequency of damaging frost in his area.

Jan 1, 1955

By Nicholas T. Zilka

Mineral resource studies by the Bureau of Mines indicate three areas within the Selway Bitterroot Wilderness have mineral resource potential. Regional studies suggest that a granitic stock on the south side of the Wilderness has high potential for a Climax-type stockwork molybdenum deposit (pl. 1, no. 8); but detailed surface investigations failed to recognize a deposit. The Elk Summit area on the north side of the Wilderness contains subeconomic resources of columbium (niobium)-bearing ilmenite in placers (p1. 1, no. 19). Subeconomic silver-copper-lead resources occur in a vein on the northeast side of the Wilderness at the Clift Mine (pl. 1, no. 2-5). The study area has no known deposits of oil and Haas, coal, geothermal resources, or other energy-related commodities.

Jan 1, 1982

In the USA, the National Institute for Occupational Safety and Health (NIOSH) does a lot of work and has provided news of interesting new developments. Marcia L. Harris describes an ?Explosibility Meter: ?In underground mines, coal dust explosions are prevented by the addition of rock dust sufficient to render the coal dust inert. Federal [US] regulations require 65% and 80% incombustible content in samples taken in intake airways and return airways, respectively, assuming a nominal coal dust size of 20% minus 200 mesh. The Coal Dust Explosibility Meter (CDEM), a hand-held instrument developed by NIOSH uses optical reflectance to measure the explosibility of a rock dust and coal dust mixture.? The CDEM is now commercially available. It provides real-time results during rock dust surveys instead of waiting weeks for laboratory results1. ?With real-time results, the potential for a disaster can be mitigated immediately. The CDEM displays the percent incombustible content as well as a colour indicating the relative explosibility of the coal and rock dust mixture. A red read-out indicates that more incombustible material is required to inert the coal and rock dust sample, while a green read-out indicates that the dust sample is sufficiently inert. When the mixture is marginally explosible, a yellow read-out is indicated. The red-yellow-green output depends upon the particle size distribution of the rock and coal dust mixture with the finer size fraction being more explosible.?

Jan 1, 2008

By Oliver Bowles

Under a cooperative agreement between the Bureau of Mines, the United States Geological Survey, and the United States Bureau of Standards, a study of the stone-quarrying industries of the country was begun in 1914. The results of investigations made have been published from time to time.1 During the World War the Bureau of Mines centered its attention on problems relating to national defense, and detailed studies of stone-quarry problems were not undertaken except for an investigation of labor saving at limestone quarries, reported in Technical Paper 203, which related to a question of military importance. Since the return of peace, the high cost of materials and labor has made more imperative than in prewar times the conduct of investigations for aiding the quarrying industries in every way possible to adopt more economical methods and to utilize the most efficient labor-saving equipment. The publications already issued have had a wide demand, and in the interest of the quarry industries the bureau proposes to issue additions to the series as rapidly as funds are available. In an endeavor to promote economy and the reduction of waste in the slate industry, a study of slate quarrying was begun in 1920 and covered a period of about two years. Sixty-five active quarries were visited, and a detailed study made of all problems bearing on their successful operation. Field study was supplemented by a study of all information available in books or published articles on slate quarrying.

Jan 1, 1922

By Manuel Gomez, V. F. Parry, John B. Goodman

"INTRODUCTION The need for an accurate and precise analytical method for determining moisture in coals of high water content has been recognized by the coal industry as well as the fuel technologist. Interest in this particular phase of coal technology extends back to the early work of German investigators on the brown coals of Central Europe. Studies by these workers led to the establishment of a direct immiscible liquid-distillation method 4/ as the accepted moisture determining technique in European laboratories. Direct moisture determining methods, those methods that utilize various techniques to drive off the water from a given sample of coal and either collect the water in a calibrated receiver or selectively trap the water driven off in a suitable absorber, have found little favor in the United States. They have been treated merely as research tools.5/ The problem of moisture determination in low-rank coals of the United States has not been given much consideration because such coals contribute only about 2 percent of the total United States production. With renewed activity in low-temperature carbonization and with the growth of interest in coal and coal-tar hydrogenation, the American coals of lover rank containing 20 to 40 percent bed moisture will be subjected to extensive investigation. If the low-rank coals of the United States are to be accurately appraised, the need for qualitative and quantitative analytical proceeded becomes more pronounced. These coals, especially the lignites of Texas and North Dakota, are highly susceptible to oxidation, a process that proceeds to a greater or less extort when low-rank, high-moisture coals are treated by oven-drying methods. The extent of this atmospheric oxidation has been described and evaluated by numerous workers. 7/In many respects, the problem of moisture determination in low-rank coals, those found in the United States and the high-moisture coals of Central Europe, is similar. Conversely, the problem of moisture determination assumes a different aspect when the coals of the eastern and the middle-west sections of the United States are considered. Present methods, the loss in weight gravimetic-type procedures, serve adequately to test these low-moisture coals. The determination of moisture in coals containing 20 to 40 percent water should be approached from a direct method rather than from an indirect gravimetic-type procedure because of the oxidative tendencies of these coals and the demonstratrated inability of a loss-in-weight technique to remove all the water in a given sample of coal."

May 1, 1953

By J. W. Miller

An investigation was begun by the Bureau of Mines in 1948 to determine the preparation characteristics of American coals. Results of the investigation were planned to be reported on a county basis and, from the data developed, to determine: (a) Which coals, either as mined or after beneficiation by conventional preparation, are suitable chemically under present standards for producing metallurgical coke. (b) Which coals require special and more intensive treatment in preparation than is now practiced. (c) Which coals cannot be considered potential sources of metallurgical coke, regardless of preparation. This report is one in a county series and describes the preparation characteristics of the coals of Logan County, W. Va. According to present-day standards for metallurgical coal, many believe that the sulfur content of the coal should not exceed 1.25 percent? Coal with more than this amount has been used for making metallurgical coke, especially when blended with coal containing less sulfur. In this series of reports 1.25 percent sulfur is used as a gage to determine whether or not a coal will be suited for metallurgical coke.

Jan 1, 1957

By Richard C. Moore

The U.S. Bureau of Mines contracted a study to review the air and water monitoring requirements of five Federal environmental acts (the Federal Water Pollution Control Act, the Safe Drinking Water Act, the Clean Air Act, the Surface Mining Control and Reclamation Act, and the Resource Conservation and Recovery Act) and to compile information on the currently available monitoring instruments. A literature review of the acts and their associated regulations was conducted to determine applicability to the mining industry as well as any air and water monitoring requirements. In addition, an industry search and literature review was performed to assess the instrumentation available to comply with the monitoring regulations. Based on this research, the instruments are classified by general applicability to air, surface water, or ground water monitoring, then catalogued by monitoring parameters. A discussion is provided on recommended and innovative monitoring techniques.

Jan 1, 1981

By James C. Fowler

As report covers the installation and testing of a permanent seismic monitor system at the Loveridge Mine in West Virginia. The testing of the system showed several things: 1. Getting the seismic data hack to the central computer in a usable form is possible 2. It is possible to detect small explosions. 3. The use of this system as a auxiliary system to detect hammer blows from miners trapped in the area of one of the geophones is possible.

Jan 1, 1974

By Clark P. Mangelsdorf

The report consists of two parts. In Part I is a state-of the-act study of roof truss technology as of January 1979. Included are a history of the truss concept, a review of analysis techniques, a record of hardware available and equipment used in its installation and numerous examples of user experience. Part II is concerned with a study of the role of friction in the behavior of a roof truss. The appendices include laboratory tests by the author.

Jan 1, 1979

By R. Luhrman, E. Christ, B. Gores, S. Fischer, E. Johanning

North American railroad locomotive operators (engineers and conductors) are exposed to multi-axis vibration and shocks (1, 2). A recent epidemiological survey showed a prevalence of serious type of neck and lower back disorders nearly double that of a control group (3). Ergonomic working conditions are important co-factors in a vibration and shock exposure risk assessment (4, 5). The goal of this study is to illustrate typical work stations (cabs and seats) in US/Canadian type locomotives and assess shock related exposure risk by calculations of the new proposed shock risk indicators according to the new ISO 2631-5 (2004) (6). Methods Locomotive cab and seat inspections were conducted and operators’ activities were assessed by a trained observer. Field measurements (n=50) were obtained during normal revue service following generally accepted guidelines (ISO 2631 (1)). A sub-sample of n=20 locomotives were selected for the calculation of proposed shock indicators (ISO 2631 (5)). Results There has been little change in basic locomotive cab and seat design in the U.S.. Two locomotive cab design concepts are used: the Association of American Railroad (AAR) Control Stand and in newer series wide-body locomotives the “Control Consol” (Figures 1-2), with varying seating conditions, but frequently subjecting the operator to an awkward body posture in addition to the vibration and shock exposure. [ ]

Jan 6, 2006

This publication is designed to be helpful in promoting health and safety in tunneling and related operations. The format has been selected and arranged to provide a condensed guide for safety personnel, inspection and investigative agencies, design and project engineers, and others responsible for the health and safety of workmen. All the precautionary measures recommended are based on actual conditions observed, from investigations of fatal or serious accidents, and from research conducted to find ways and means of alleviating hazards and unhealthful conditions. Many of the recommended rules are included in State laws and in the general safety requirements of the construction industry. Explanatory, descriptive, and qualifying information has been largely omitted in this publication to keep basic data in more useful and compact form. Included in the appendixes are special precautions for gassy (methane atmospheres) tunnels and tunnels where petroleum products are encountered.

Jan 1, 1968

By Robert H. Peters

Groundfall accidents have been the leading cause of fatalities in the underground coal mining industry for many years. Statistics from the Mine Safety and Health Administration (MSHA) indicate that approximately half of the victims of these fatal accidents were in an area where no devices had been installed to support the mine roof. This report was prepared by the U.S. Bureau of Mines to provide guidance to operators of underground mines concerning the use of techniques that may help to keep miners from going under unsupported mine roof. The report is divided into two major sections. The first section reviews the findings from several areas of empirical research pertaining to strategies for convincing employees to avoid unsafe acts and/or adopt self-protective behaviors. The strategies are (1) incentives and feedback, (2) disciplinary actions, (3) training (primarily fear communications and behavioral modeling), and (4) nondirective techniques. This literature review has a broad focus and should be helpful in making decisions about how to encourage a wide variety of types of self-protective behaviors. The second major section of the report presents an analysis of each strategy's potential for keeping miners away from unsupported roof.

Jan 1, 1991

By Neil J. Mansfield, Setsuo Maeda

The purpose of using experimental subjective and/or perception methods is: (a) to understand human subjective impressions of the physical characteristics of vibration; (b) to determine the relationship between the subjective perception of some aspect of the vibration and an evaluation index of the physical vibration characteristics; and (c) the establishment of target values for design of vibration environments in terms of human sensation of vibration characteristics. In order to understand the relationship between a physical measure of the mechanical vibration and the subjectively perceived aspect of the vibration environment, experimental methods shown in Table 1 have been used1. [ ] The constant measurement methods of Table 1 are mainly used for measurement of the threshold of human sense. The subjective scaling methods are mainly used for obtaining subjective (or proportional) scaling between the perceived quantity and physical quantity. In this review, the fundamental approach of experimental methods for obtaining the target values used in the design of vibration environments, and the different findings between the subjectively perceived methods for evaluating human response to vibration characteristics and the physical quantity of the vibration environment are summarized. Fundamentals of Subjective Scaling The relationship between the experimental psychological methods for providing target values in the design of the vibration environments and the physical quantities is illustrated in Fig. 1. Vehicle mechanical vibration can be characterized using many metrics, and these can be considered the ‘input’ to the human. In order to predict subjective responses to the vibration, it is necessary to link the characteristics of the source of vibration and human reactions, the ‘output’.

Jan 6, 2006

By James C. Cawley

This paper updates an earlier report by the authors that studied electrical injuries from 1992 to 1998. The previous information is expanded and supplemented with fatal and nonfatal injury rates and trends through 2002. Injury numbers and rates were used to compare and trend electrical injury experience for various groups and categories. This information allowed identification of at-risk groups that could most benefit from effective electrical safety interventions. The data presented in this paper are derived from the U.S. Labor Department?s Bureau of Labor Statistics? Census of Fatal Occupational Injuries, Survey of Occupational Illnesses and Injuries, and Current Population Survey. Between 1992 and 2002, 3378 workers died from on-the-job electrical injuries. Electricity remained the sixth leading cause of injury-related occupational death. From 1999 to 2002, 4.7% of all occupational deaths were caused by electricity, down from 5.2% in the 1992?1998 time period. The cause of death was listed as electrocution in 99.1% of fatal cases. Contact with overhead power lines was involved in 42% of all on-the-job electrical deaths. The construction industry accounted for 47% of all electrical deaths between 1992 and 2002 but showed overall improvement from 1995 to 2002 by reducing its electrical fatality rate from 2.2 to 1.5 per 100 000 workers. In addition, 46 598 workers were nonfatally injured by electricity. Contact with electric current of machine, tool, appliance, or light fixture and contact with wiring, transformers, or other electrical components accounted for 36% and 34% of nonfatal electrical injuries, respectively. Contact with underground buried power lines was involved with 1% of fatal injuries and 2% of nonfatal injuries. The research of the National Institute for Occupational Safety and Health aimed at evaluating commercially available overhead power line proximity warning alarms is described. This paper is expected to be the initial step for eventual development of a performance standard for such systems.

Jan 1, 2008

By Donlad B. Lindsay

This report describes a field-test program to determine the effectiveness of a polymeric wall sealant to reduce the excape of naturally occurring radio-active gas radon from the walls of an underground uranium mine into the ventilation air. A 75-foot-long, dead-end drift with a surface area of about 6,000 ft2 was used as the test site in which the average natural radon flux from the normally dry rock was 16 fCi/cm2-s. The effect on radon emanation of wetting the walls with water to a depth of 3 inches was tested, after which the rock was completely covered with a coating of dry-mix concrete to provide a base for the sealant, an acrylic latex. Sealant was applied in two coats to about 0.25 mm thick. An overall reduction of average radon flux of about 75 pct was achieved. Radon production and other environmental values were measured continuously and automatically by a Bureau of Mines data acquisition system. A commercial microcomputer was programed to convert raw data to engineering units and to perform other useful operations while recording all data on magnetic diskettes. Direct measurements of radon flux from the rock surface were made by a charcoal adsorption technique.

Jan 1, 1981

By John J. Mulligan

The Bureau of Mines investigated the tin deposits of the Cape Mountain area during July and August 1962 to test the effectiveness of detrital-cover sampling in permafrost areas as a relatively cheap and simple means of guiding mine development and exploration. Results indicate that systematic detrita1-cover sampling can be used effectively to delineate obscure deposits with sufficient accuracy to permit sampling with a minimum of trenching or drilling. Extensions of known outcroppings were traced in sufficient detail to guide lode sampling and several previously unknown tin-bearing lodes were found and sampled. Lode sampling was limited to the minimum needed to establish the reliability of detrital-cover sampling results. The results of previous lode and placer investigations are summarized and detrital-cover sampling methods and results are described in detail.

Jan 1, 1966

By Charlie Vaught, Bill Wiehagen, Lynn Rethi, Pamela Kidd, Lisa Steiner, Ted Scharf, Henry Cole, Kathleen Kowalski

The most hazardous work environments share one feature in common: constant change. Many different, but constantly changing hazards are found in agriculture, construction, mining, and transport. This dynamic feature of work-place hazards varies by: (1) degree of control, (2) predictability, (3) visibility, (4) movement, and (5) degree of speed and force. In some cases the actions of the dynamic hazards are required for production to take place, and in many cases,