Search Documents

By Michael R. Norland

Surface and subsurface stabilization of mining-related wastes through revegetation depends upon the physical, chemical, and biological condition of the waste following mining. Mining disturbances can significantly alter the soil physical, chemical, and biological characteristics of a site, reducing or eliminating mycorrhizal fungi from the soil. Mycorrhizae are economically and ecologically important because they can alleviate environmental stresses caused by lack of proper soil condition and because they are vital to stabilization of mining waste by increasing plant survival and biomass through increased nutrient and water uptake. This report discusses some of the ecological factors that may affect mycorrhizae-plant associations on mining-related wastes and provides general information on mycorrhizae inoculation technology.

Jan 1, 1993

By Rudy J. Matetic

The National Institute for Occupational Safety and Health (NIOSH) at the Pittsburgh Research Laboratory (PRL) is conducting research to reduce the noise exposures of roof bolting machine operators and to prevent additional cases of Noise Induced Hearing Loss (NIHL) thru the development of engineering noise controls. This paper describes and evaluates an engineering noise control for the roof bolting machine, namely the collapsible drill steel enclosure. The results of the evaluation demonstrated that using the collapsible drill steel enclosure provided a 7 dB(A) reduction in sound pressure level at the operator?s position of a roof bolting machine.

Jan 1, 2008

By L. C. IlsLey

"There is an old saying that ""It is too late to lock the stable after the horse is stolen"". Is not this just what is being done by many mine operators today when it comes to buying safe electrical equipment for gaseous and dusty coal mines?The ""open type"" of electrical equipment or even the ""half safe"" type represents the unlocked stable. After the mine disaster, and after men have lost their lives, the lock is put on - that is, safer equipment is installed.For example, an open type of electric coal drill was used in a gaseous mine in West Virginia, This was the probable cause of the death of 27 men. A half safe type of electric coal-cutting machine was used in a gaseous mine in Pennsylvania. This was likely the cause of the death of 36 men. An unapproved, unsafe type of flame safety lamp was used in a gaseous and dusty mine in Utah. This was the all¬eged cause of the death of 171 men. All three disasters happened within the last six months, and seem to have been avoidable if proper equipment had been used.It is understood that more rigid requirements will be enforced in West Virginia. The committee of State mine inspectors made definite recommendation for im¬proving the conditions in the given mine in Pennsylvania. The Industrial Commission of Utah have already issued new orders which will remedy the use of unsafe lamps in that State.These acts and recommendation are all good and will help prevent accidents in those States in the future. Is it not a pity that such recommendations and order were not made a little earlier before the tell of life had been exacted? Is it not a pity that other States will not take these lessons to heart and safeguard their mines before and not after disasters take place?Electric current can cause accidents in five general ways as follows: (1) By shock to persons; (2) by igniting powder; (3) by igniting gas; (4) by igniting coal dust; and (5) by setting fire to inflammable material such as timber and coal. A great many accidents from these causes are preventable if proper care is taken. Most of the accidents caused by sparks and flashes from electrical apparatus would not take place if approved electrical equipment was used. By approved equipment, the writer means equipment that has been tested and formally approved by the Bureau of Mines. So far as known, up to the present time, no disasters have been caused by sparks or flashes from equipment having the Bureau's approval."

Jul 1, 1924

The Appalachian Mountains divide Pennsylvania into two distinct coal regions, bituminous and anthracite. The western region of the the state, where the majority of bituminous mines are located, is characterized by mountains and gently rolling hills. Bituminous coal seams underlie about 12,000 square miles in 28 counties. The anthracite coal region, located in the northeast, covers approximately 3,300 square miles. This area contains more than 20 different coal beds that vary in thickness from a few inches to 50 or 60 feet. The anthracite region is characterized by steeply pitching seams that require highly specialized mining techniques and present unique challenges for solving problems such as the mine subsidence associated with abandoned underground anthracite mines. For more than a century, coal has played a major role in the economic and industrial development of Pennsylvania, particularly the steel industry. Estimated bituminous reserves total 23 billion tons, or 5.3 percent of U.S. reserves, and anthracite reserves total 7.1 billion tons, or 97 percent of U.S. anthracite reserves. Pennsylvania received conditional approval of its regulatory program July 31, 1982. Pennsylvania's Abandoned Mine Land Program was approved on the same date.

Jan 1, 1992

By F. B. Petermann

The Bureau of Mines conducted electric furnace smelting tests on sintered flotation concentrate and siliceous log-washed are. The flotation concentrate was derived from the Maggie Canyon deposit of the Artillery Mountains area, Mohave County, Ariz., and contained, before sintering, 35.6 percent Mil and 19.4 percent Si02 + A1203. The log-washed ore was from the McGregor deposit of the Artillery Mountains area, Mohave County, Ariz., and contained 31.2 to 33.6 percent Mil, 19.5 to 27.6 percent Si02 + A1203, and 2.5 percent Pb. This work was undertaken to determine the most effective smelting technique for producing standard products from such nonspecification ore and concentrates. The objective was to collect data, using a small furnace, which would be reasonably accurate and permit extrapolation to large-scale practice for comparing with results on specification-grade are.

Jan 1, 1962

By A. C. Burr

This progress report covers the period from January 1949 to the end of the fiscal year, June 30, 1950. Three runs were successfully completed, and one run was terminated as the result of failure of a cast reaction tube. Including the abbreviated run, the gasifier was operated for 1,915 hours, during which some 428 tons of natural and steam- dried lignite was partly gasified In producing 20 million cubic feet of gas. Gas-production rates varied from 7.8 to 16.4 thousand cubic feet per hour, the latter being the highest production rate yet reached; hydrogen-carbon monoxide ratios of the product gas varied from 1.85, the lowest ratio yet produced, to 6.5; and heat-transfer rates through the heated wall of the outer tube varied from 2,100 to 4,400 B.t.u. per square foot an hour. The general objective of the project is to establish the technology and economy of the gasification of lignite in an externally heated, metal, annular retort. Specific objectives include determination of the useful life of the metal retort tube, which is a continuing problem, and special objectives that were established for each run as part of the systematic investigation of the basic variables of the gasification process. For runs 10 and 11 the special objective was the influence of the lignite feed rate on gasification; for run 12, a comparison of dried and natural lignite, and the production of gas having a hydrogen-carbon monoxide ratio less than 2; and for run 13, the influence of a gradually increasing steam rate with steam admitted to either the upper or lower reaction zones. In addition, during each run the sulfur distribution and concentration in the product gas and char were investigated. Experimental results obtained using the lignite feed rate as the variable indicated that the gas yield per ton of natural lignite varied inversely with the feed rate. Comparison of the gasification of natural and steam-dried Dakota Star lignite indicated that the dried lignite was a superior gasification material because: 1. The hourly gas production was higher at normal combustion space temperatures under nearly equal experimental conditions. 2. On the moisture- and ash-free basis, a considerably higher feed rate could be maintained at a relatively high percentage of carbon gasified. 3. At nearly equal moisture- and ash-free feed rates, the specific gas yield was higher. The location of steam admission was found to be important because the gas yield per ton of natural lignite was higher when at least a portion of' the process steam was admitted to the upper reaction zone. Heat balances showed the potential heat in the gas and char to be 71.8 to 83.6 percent of the total heat input. The sulfur concentration in the product gas was low, being in the range of 35 to 140 grains per 100 cu. ft., of which 1.5 to 2.3 grains was organic sulfur. Careful measurements and inspection of the 310-alloy rolled plate tube following runs 11, 12, and 13 showed no excessive corrosion; however, some radial deformation had occurred indicating that deformation or creep might be the limiting factor in the life of the tube.

Jan 1, 1953

By James M. Link

Underground coal mining is the most hazardous industrial occupation in the United States.. Haulage accidents in underground coal mines contribute substantially to the occupational hazards of this type of work. In an effort to improve mine safety, a completely hydraulic transport system has been designed to move coal from the mine face to the preparation plant. The capital investment for the hydraulic haulage system is great, and the size of the mine developed for this study is large. Mine production for the conventional haulage mine is 1. 1 million tons of clean coal per year, while the hydraulic haulage mine will produce over 1.6 million tons of clean coal per year. Safety statistics for a number of mines of this size are shown.

Jan 1, 1975

To improve a miner's chances for survival in an emergency by providing an improved self-rescuer device that functions in a toxic or oxygen-deficient atmosphere. The Approach: Development of a compact, lightweight apparatus which produces oxygen by using the wearer's breath in a chemical reaction. How It Works: The device is designed to cause the user's breath, which contains water vapor and carbon dioxide, to react with potassium superoxide (K02) to produce oxygen in quantities sufficient to sustain the wearer for one hour. The system is a closed circuit and does not depend on "screening" of noxious gases. To use the device, the miner opens the top and

Jan 1, 1974

By N. T. Lowe

This Bureau of Mines publication presents salient deposit information in abstract form on 119 principal mineral deposits in the State of Nevada. Commodity coverage addresses 17 critical and strategic commodities that appear to have commercial production potential in the State. The core of the deposits described is taken from those properties evaluated d under the Bureau of Mines Minerals Availability Program (MAP); additional deposits are included to provide a more complete coverage. Institutional and infrastructural factors affecting mineral development are also discussed.

Jan 1, 1985

By Stephen M. Jasinski

This report describes the materials flow of mercury in the United States. It examines the mining and production of mercury and the manufacturing, uses, and ultimate disposal of mercury. Materials flowcharts were prepared for 1989 and 1990. An effort was made to include estimates for all major anthropogenic sources including fossil fuel combustion, waste incineration, and nonferrous metal mining operations. Mining and mineral processing released about 100 mt/yr of mercury to the environment in both 1989 and 1990. The combustion o ii fu1s released 175 mt/yr in the same years. The manufacturing, use, and disposal of products containing mercury accounted fix the release of 1,037 mt of mercury in 1989 and 938 mt in 1990. The manufacture of chlorine and caustic soda was a major source of recycled mercury, but it was all reused within the industry. Recovery from all waste products accounted for 36% of reported consumption in 1989 and 42% in 1990. The losses from manufacturing and end use have been declining, whereas mercury emitted from combustion sources has not been strictly regulated and will likely become the largest source of mercury releases to the environment.

Jan 1, 1994

By Paul M. Tyler

The technology of clay and the manufacture of ceramic products therefrom, and also the clay resources of most of the individual States, are already covered by a voluminous literature. The present resume touches these matters only briefly; its purpose is essentially to bring together in small compass certain of the elementary factors affecting the potential commercial value of a clay deposit. In its preparation the author made extensive use of the annual chapters on Clay in Mineral Resources of the United States and in the two annual issues of the Minerals. Yearbook that succeeded them. For careful review and constructive criticism of the manuscript, the author is indebted to Hewitt Wilson. GENERAL DESCRIPTION The term ?clay? includes a great variety of substances that may differ widely in chemical mineralogical and physical properties. No two clays are exactly alike. All of them however, have the prominent characteristic of becoming more or less plastic when wet. Nearly all of the useful clays can be molded into articles, will hold their shape while being dried, and can be converted into a hard, rocklike substance by heat. Clay may, and in fact usually does, consist of a number of minerals among the commonest of which are kaolinite, quartz, feldspar, iron oxides, mica, bauxite, calcite, and manganese oxides. Organic matter is often present. Pure kaolinite, which has the formula A1203. 2 SiO2. 2H2O, is ordinarily, considered to be the parent "clay substance," butt most clays contain other hydrated mixtures of alumina and silica (aluminosilicic acids) along with indefinite amounts of sand and other nonessential minerals3/ Even, this so-called inert matter affects the plasticity, drying shrinkage, ease of drying, and final density, and at high temperatures may react chemically with the clay substance.

Jan 1, 1929

By O. C. Blade

This report on the properties of aviation gasolines and aviation jet fuels produced in the United States during 1955 was made under a co-operative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior. Analytical data are presented for 116 samples of aviation gasoline and for 38 samples of aviation jet fuel. The analyses were made on samples typical of the manufacturers' 1955 production in their laboratories and the results submitted to the Bureau of Mines for compilation. The products of 20 manufacturers of aviation gasolines and of 16 producers of aviation jet fuels are represented.

Jan 1, 1956

By Terry J. Close

At the request of the Idaho Congressional Delegation, the U.S. Bureau of Mines Western Field Operations Center investigated the mineral resources of the 140,000-acre Red Mountain roadless area, located northeast of Lowman, in central Idaho. The area includes U.S. Forest Service Red Mountain RARE II area (4-063). The highly mineralized road less area is underlain mainly by granitic rocks which are transected by a northeast-trending fault system. Associated with the granitic rocks and fault system are gold and black sand mineral resources. At least 1,395 ounces of gold and 858 ounces of silver have been recovered from six lode and placer mines within the roadless area. A total of 525 tons of columbium-tantalum, 2,049 tons of euxenite, 83.5 tons of columbite, and 54,862 tons of ilmenite concentrates have been produced from a nearby black sand mineral placer. Mine workings and facilities in the roadless area consist of two dismantled mills, 15 open and caved underground excavations totaling about 2,900 ft of workings, seven large pits and quarries, over 166 smaller dozer-and hand-dug prospect pits and trenches, and in excess of 66 drill holes. The mineralized sites in the roadless area are covered by about 690 current (1992) mining claims. About 130 individuals are holding the claims. Also within the roadless area are four patented lode mining claims. Twenty-five of the 54 mineralized sites identified during the study of the roadless area have, or likely have, mineral resources. One has gold and three have black sand mineral resources that are marginal or subeconomic. There also are two hot springs with thermal water resources, some veins that could be sources of decorative quartz, and dimension stone which was quarried in the past and could be again.

Jan 1, 1993

By Richard L. Sanford

This report summarizes the results of the development of a Directory of Computer Programs Applicable to U.S. Mining Practices and Problems. The Directory includes a sampling of computer usage in operating and manufacturing companies, consulting firms, computer companies, research organizations, universities, and various U.S. government agencies. References to computer applications throughout the mining industry are presented as well as comments on the availability of programs to interested organizations or individuals.

Jan 1, 1977

By C. E. Gregory

In terms of a Research Proposals supported by a Grant Agreement dated 30 June 1973, the author was commissioned to prepare an annotated bibliography of mine fires. The main objective was to conduct a comprehensive program of library research and search of official files to prepare a list of articles dealing with actual occurrences of mine fires. This bibliography as now completed includes an annotated reference from each article or report cited, underlining the cause, extent, methods used, procedural errors made, results achieved, ventilation effects, and lessons learned from the operation of subduing the particular fire.

Jan 1, 1974

By Bill Linville

During fiscal years 1967-68, the Bureau of Mines produced 185 technical papers and reports about petroleum and oil-shale research, which were published either by the Bureau or by others as referable scientific literature. Numerous other reports were prepared for Government agencies, State agencies, and organizations of the petroleum and natural gas industry engaged in cooperative research programs with the Bureau. Research performed during the reporting period by the Bureau on petroleum, natural gas, and oil shale was classified by 71 active projects. A basic appropriation of $3,575,000 was supplemented by $1,300,000 in fiscal year 1967, and that of $4,043,000 by $1,402,000 in fiscal year 1968, making the appropriated-to-supplemental fund ratios about 2.8 to 1 for fiscal year 1967 and 2.9 to 1 for fiscal year 1968. In fulfillment of the mission of the Bureau, through planned research programs, methods for producing and utilizing petroleum were improved. The continued conservation of this natural resource of petroleum, including crude oil, natural gas, and oil shale, was pursued through research performed by some 350 personnel at two petroleum research centers and two petroleum research laboratories supervised and supported by administrative personnel of the Bureau and the Department of the Interior.

Jan 1, 1970

By Michael T. Nigbor

This Bureau of Mines publication identifies the significant environmental issues associated with the potential development of strategic and critical minerals in the Stillwater Complex, MT. The Stillwater Complex contains deposits of Cr, platinum-group metals (PGM), and Ni. Issues that must be addressed prior to minerals development include the effects mining, milling, and smelting will have on the land, water, and air, and methods of minimizing the environmental impacts.

Jan 1, 1985

By D. Harrington

This circular is part II of a series of papers reviewing the literature on air conditioning in mines with particular reference to the health, safety, and efficiency of employees. It deals with the physiological aspects of the principal physical qualities of mine air; part I (Information Circular 7001), chapters 1 to 3, discussed the physiological aspects of the chemical qualities of mine air, especially when contaminated with organic matter and noxious and toxic gases; part III will describe theoretical and practical methods of air-conditioning mines to try to correct or alleviate the conditions mentioned and will discuss the results attained by some of the systems now in use in various parts of tae world. With the present emphasis on the necessity for preserving the health of the Nation's defenders, industrial as well as military, attention should be called to the various conditions that may affect adversely their health and efficiency. One of the most important of these is exposure to abnormal air conditions, especially high temperatures and humidities. Therefore, it is believed that although the data presented here on the physiological effects of exposure to high temperatures cue intended mainly for the mining and allied industries, they are applicable to many other defense industries as well as to conditions present in some activities of the Army and Navy.

Jan 1, 1941

By LeRoy D. Loy

The disposal of excess overburden from surface mining can be accomplished by use of a reclamation technique entitled head-of-hollow or valley fill. This report attempts to assess current valley fill regulations and practices, identifies inherent benefits and deficiencies, and develops concepts to enhance fill technology.

Jan 1, 1978

By C. Ozgen Karacan, William P. Diamond

In This Chapter [Measuring the gas content of coal Predicting gas emissions based on geologic and coal reservoir property data Determining the gas storage capacity of coalbeds and other gas-bearing strata Methane drainage borehole monitoring to forecast the remaining gas-in-place and the influence on mine emissions Forecasting gas emissions during mining as a function of mining parameters and Gas emission prediction based on numerical simulation] This chapter provides guidelines for determining the gas content of coalbeds, estimating the gas-in-place, and predicting gas flow and emissions before and during coal mining operations. The techniques are discussed briefly in the following sections. However, detailed information on the techniques is provided in the cited references. INTRODUCTION Coalbed methane, if not properly controlled in the underground mine environment, is a safety concern due to the potential risk for an explosion. This is a particular problem during longwall mining, where the high rate and volume of coal extraction can result in the release of large amounts of methane from the mined coalbed and other adjacent gas-bearing strata. The variability and potential hazards of these sometimes unexpectedly high gas flows provide the impetus to develop methods to predict methane emissions into the underground workplace. A forecast of the volume of gas that might be released during coal mining is helpful for designing ventilation systems and for implementing optimum methane drainage strategies to help mitigate expected gas emission problems. A complete assessment of the need for methane drainage prior to mine development generally requires both an empirical and a theoretical approach. If there are active mines in the general area with similar geologic conditions and coal characteristics, a review of gas problems in those mines provides an initial insight into the level of gas emissions to be expected at a new location. In addition, relatively simple methods exist to determine the in situ gas content (volume of gas per unit weight of coal) of the coalbeds in a particular mining area, as well as the gas-in-place (volume of gas in the coalbed(s) within a defined geographic area).

Jan 6, 2006