Search Documents

By H. Reginald Hardy

This report is Volume I of a three volume final report on the micro-seismic monitoring of a longwall coal mine. Volume I deals for the most part with the detailed aspects of the microseismic field study itself, however, brief references are made to other secondary studies described in Volumes II and III. During this field study a mobile microseismic monitoring facility and associated transducers were employed to detect and record microseismic activity above a longwall panel at Greenwich Colleries, Barnesboro, Pennsylvania. The fundamental objectives of this study were (1) to evaluate the feasibility of detecting microseismic activity originating from longwall mining operations using an approximately planar, near-surface, geophone array installed above the longwall and (2) to attempt to locate the sources of the various microseismic events. This investigation has proven that, using the techniques developed it is possible to detect microseismic events at depths of more than 400 ft and at horizontal distances in excess of 800 ft from the source. The majority of the observed events were found to have frequencies on the order of 10 to 100 Hz, and particle velocities of 50 to 300 µips. When a suitable velocity model was utilized, most of the events located were computed to be within ±100 ft vertically of the coal seam and ±50 ft horizontally of the longwall face. The results of the overall research project suggest that additional research should be undertaken in a number of associated areas.

Jan 1, 1978

By R. W. Fatzinger

The accident-frequency rate for placer mining in 1942 is reported as 36.923 accidents per million man-hours worked. This figure places placer-mining accident frequency slightly higher than that given for quarrying-35.7-but considerably under the 78.0 for coal mining and 56.5 for metal mining.4 Placer mining is subdivided into four types of activity: Underground, surface, dredging, and hydraulicking. It is the purpose of this paper to present and discuss safety practices in dredging and hydraulic mining; therefore, the following considerations will be limited to these two types of placer mining.

Jan 1, 1948

By John R. Troxell

"INTRODUCTION The Ahles iron mine, also known as the Pequest mine, in Warren County, N. J., was operated continuously for 15 years and was still in ore when it closed in 1916.Tie property was examined by an engineer of the Bureau of Mines in March 1943. 3/ This examination led to an investigation of the deposits by the Bureau by diamond drilling two holes under the old workings to determine whether the extends downward.This report describes the work done at the Ahles mine by the Bureau and presents the data obtained.ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. The Mining Division, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual investigative work, and prepares the final report.The Metallurgical Division, O. C. Ralston, chief, analyzes samples and performs beneficiation tests.The investigation was under the general supervision of J. B. Zadra, acting regional engineer, and under the immediate supervision of G. D. Jermain, district engineer for the States of Pennsylvania, New Jersey, Maryland, and Delaware. The author was in direct charge of the project.The chemical analyses for the project were performed at the College, Park, Md., laboratories of the Bureau of Mines under the direction of M. S. Sheftel. The ore-dressing tests were conducted at College Park under the direction of Frank Lamb. Preston E. Hotz, of the Federal Geological Survey, logged and interpreted the drill cores."

Apr 1, 1948

By Oliver Bowles

ASBESTOS is a name applied to a group of naturally fibrous minerals. As indicated in a later section devoted to a detailed discussion of the early history of asbestos, the tern may be defined as a. fibrous form of serpentine or amphibole. It does not include fibrous forms of other minerals, such as wollastonite, nemalite (fibrous brucite), or the fibrous forms of calcite or gypsum. A material that has the characteristics of silk or cotton and at the same time will not burn is unique. Because it combines these qualities with other advantageous properties, asbestos has specialized uses for which no substitutes are yet available. Asbestos furnishes a major raw material for a great variety of essential products and their manufacture constitutes a vast industry. The United States leads all countries in the manufacture of asbestos products. The value of such commodities manufactured in 1952 exceeded $332 million. They are not only of vast importance to budding construction and industry but axe absolutely, essential to certain important fields of use, for example, steam packings and friction materials, such as brake-band linings on automobiles.

Jan 1, 1955

By J. K. Whyatt

The U.S. Bureau of Mines conducted an overcore stress measurement on the 5300 level of the Lucky Friday Mine, Mullan, ID, to investigate the stress regime around an experimental stope in a rock-burst-prone mine. The result indicated a stress field with unexpected magnitude and orientation [s 1 ?135 MPa (19,600 psi) oriented S 80° W). An unusual amount of rock-burst activity was encountered during subsequent excavation. A careful review of the overcore data suggested the overcore strain measurements were valid. Moreover, concentrated rock-burst activity suggested that the measured stress field did exist, but was localized and therefore did not represent the far-field in situ stress field.

Jan 1, 2010

By Jerry T. McLendon

The proper disposition of phosphatic clays has been the subject of research and debated for years by phosphate producers, State and Federal research agencies, regulatory authorities, and environmentalists. To date, no "universal" solution exists for the ultimate disposl of phosphatic clays. This Bureau of Mines report examines the state of conventional clay disposal technology and reviews the technical progress of innovative alternatives. Twenty impoundment sites were investigated by the Bureau of Mines using geotechnical methods and laboratory analysis of cored samples. In addition, quasi-static cone penetrometer soundings were conducted to define clay and/or sand-clay interfaces en masse. Samples of the top, middle, and bottom hole segments were obtained at each station for laboratory studies of clay densities, pore fluids, plasticity, and mineralogical properties. The results of this study support the continued use of initial clay settling impoundments but emphasize the need for "in-line" systems to reduce the initial volumes of plant-generated phosphatic clays. The effective use of sand tailings is also encouraged to promote further consolidation of clays via self-weight stressing, sand-clay admixtures, and/or surcharging sand caps.

Jan 1, 1984

By D. I. Bleiwas

The Bureau of Mines determined demonstrated tin resources and costs associated with tin production in order to evaluate the potential for tin production from 18 market economy countries (MEC's). Data were collected from tin producers, in most cases during on-site visits. The analyses evaluated the relative economic and resource position of 146 mines, deposits, or regions in January 1984 dollars. The demonstrated resource of recoverable tin within the nations studied is approximately 2.8 million metric tons (mt). Of this total, over 73 pct is recoverable from the Southeast Asian countries of Malaysia, Thailand, and Indonesia, which in 1983 accounted for almost 60 pct of the world's tin production. Brazil has joined the Southeast Asian countries as a major low-cost, high-volume supplier of tin and is likely to continue to expand its production. Given the 1984 market structure, over 60 pct of the tin in demonstrated resources was economically recoverable. Historically, the International Tin Council (ITC) has helped maintain relatively stable tin prices through a buffer stock and sales quotas. In late 1985, exhaustion of buffer stock funds led to suspension of tin trading on the world's major tin metal exchanges.

Jan 1, 1986

By C. C. Hustwit

The U.S. Bureau of Mines formulated a new mathematical model to characterize iron oxidation. The new model is intended to replace the currently used model, recommended by the Environmental Protection Agency (EPA), for most acid mine drainage (AMD) treatment applications. The new model was evaluated in a series of five synthetic AMD treatment tests. The initial ferrous iron concentrations ranged from 800 to 2,400 mg/L. In these tests, the Bureau model underpredicted the measured ferrous iron oxidation rates by a range of 3.24 to 8.03 pct. This was considered to be in close agreement after consideration of experimental error. The model proposed by the EPA was also evaluated using the same test data. The EPA model underpredicted the oxidation rates by a range of 77 to 100 pct in four tests and overpredicted by 19 pct in one test. The model formulated by the Bureau expresses that the rate of iron oxidation is a function of a treatment system's oxygen transfer efficiency and is independent of ferrous iron concentration when treated to near-neutral pH's. A new test method for evaluating oxygen transfer in flow-through reactors is also described.

Jan 1, 2010

By D. E. Redmon

Exploration of hidden mineral deposits becomes increasingly important as known ore reserves are depleted. The primary objective in any exploratory program is to obtain enough reliable information to evaluate accurately the potential of the mineral deposit. Constant improvement in equipment and technique has established drilling as one of the most valuable methods of exploration. This paper presents the results of studies of several drilling methods currently used in the search for uranium deposits in sedimentary formations from surface drill sites. Also presented is a description of drilling with wire-line equipment from an underground location in metamorphic rocks. The studies were conducted in the Colorado Plateau area and in northwestern New Mexico and Wyoming. Statements of a general nature pertain to conditions or situations existent in those areas.

Jan 1, 1960

By B. K. Shibler, A. O. Ipsen, W. W. Agey

"INTRODUCTION As a part of the program of investigation of domestic sources of manganese ore, mining engineers of the Bureau of Mines obtained and examined samples of ore from six properties in the vicinity of Pioche, Lincoln County, Nev., and from one property near Caliente, Lincoln County, Nev. As the ores were too low-grade to be acceptable for the direct production of ferromanganese, their amenability to concentration by ore-dressing methods was investigated.In general, the Pioche ores had a low manganese content and, owing to extremely intimate association of manganese minerals with iron oxide and nonmetallic gangue, were refractory to concentration by ore-dressing methods. Only two samples (Zero Gap and Wheeler ores) were amenable to the production of concentrates that would sinter to a marketable plus 35-percent manganese grade. The Prince Consolidated and Ely Valley No. 1.ores were roasted and sintered to produce lead-silver-zinc fumes. The residues were of possible value as manganiferous iron ore. No marketable manganese products were made from Calton semi-oxidized ore, but over 80 percent recoveries of lead, silver, and zinc were made by bulk sulfide flotation followed by Diming of the sulfide concentrate. No satisfactory results were obtained by treatment of Golden Eagle and Ely Valley No. 2 ores.The Cudverwell ore was amenable to the production of high-grade manganese concentrates by ore-drssing methods. However, fine grinding was required to effect mineral liberation, and loss of manganese as slime limited the mangenese recoveries obtainable.In the coarse of the investigations, many data were obtained and compiled, but for the sake of brevity, several data, of secondary importance have been omitted or condensed, and only the tests giving the more promising results are discussed in detail. For convenience, the report has been divided into two parts, one opertaining to the Pioche ores and the other summarzing results obtained by testing Culverwell ore."

Aug 1, 1947

By W. C. McLaughlin

Under a cooperative agreement, the Bureau of Mines, Magma Copper Co., and ASARCO, Inc., tested backfilled ground support systems at t.wo elevations in Magma's San Manuel, AZ, mine. The tests were mainly for guidance in designing the loading crosscuts of the new ASARCO Sacaton underground mine. Two-piece, wide-flange steel sets for 8-by 8-ft (2.44-by 2.44-m) and 11-by II-ft (3.36-by 3.36-m) openings were designed. Set spacing was 3 ft (0.91 m) and 5 ft (1.52 m), respectively. After erection, the sets were lagged with various test materials. The void between the lining and the ground was backfilled with sand and pea gravel. Instruments measuring strain (used to determine changes in stress) were placed beneath the sets and in the backfill. Results indicate the backfilled sets in the smaller drift (2315 grizzly level, panels 6 and 7) of 8-by 8-ft (2.44-by 2.44-m) cross section are a viable permanent support system, lower in cost than the standard formed concrete. Results are inconclusive in 2615 grizzly level, panels 5 and 6, where wide-flange steel sets were used with 5-ft (1.52-m) long concrete gob lagging of T-design.

Jan 1, 1983

Assess the technical feasibility of mining small and/or deeply buried frozen placer deposits from the surface through boreholes.

Jan 1, 1997

By Charles F. Jackson

Gold mining is a subject that not only appeals to the popular imagination but has vital importance to the world's economic structure. However, a discussion of the use of gold as a medium of exchange, and a basis for credit between nations and for monetary systems is not within the scope of this paper. The importance of gold in carrying on the commerce of the world, the present supply and rate of production, the probable trend of future production, the probable future requirements, and related subjects have recently received much attention from bankers and economists, and many articles on these subjects have been published. During slack periods of base-metal production due to falling prices, accompanied by scaling down of base-metal mining operations and often by the closing down of at least some mines, there usually result revival of interest in gold mining, search for previously undiscovered deposits, and reopening of some old gold mines.

Jan 1, 1932

By Arthur L. Crawford, R. E. Head, Glen Burgener, F. E. Thackwell

"INTRODUCTION This report embodies the results of a detailed statistical microscopic examination of the ore and the mill products of the Silver King Coalition Mines Co., Park City, Utah.The study was conducted under the joint auspices of the United States Bureau of mines is cooperation with the University of Utah at Salt Lake City, Utah. The work was done in the cooperative Microscopic Service Laboratory, which was equipped by contributions from the following companies: Utah Copper Co., International Smelting & Refining Co., American Smelting & Refining Co., United States Smelting, Refining & Mining Co., Tintic Standard Mining Co., Silver King Coalition Mines Co., and Park Utah Consolidated Mines Co. The salaries and the other costs involved in operation of the laboratory were met by contributions from certain supporting companies. In addition to the regular personnel of the laboratory the Bureau of Mines contributed the part-time services of a microscopist-consultant to direct and assist with the technical work.ACKNOWLEDGEMENTSThe authors acknowledge the courtesies extended by the Silver King Coalition Mines Co., through its general manager, M. J. Dailey, in furnishing the various ores and products on which the study was made, together with general information concerning the problems encountered or recognized in connection with the milling of the Silver King ore."

Jun 1, 1934

By K. E. Robinson

Appendix A is an abridged extract of the report prepared by the Geotechnical and Structural Engineering Society of Idaho, and presents the results of their one-year study to evaluate the feasibility of disposing mill tailings by landfill construction. Appendix B describes the field and laboratory testing program completed by RDM to assess the effectiveness of a soil (slimes) liner as a means of seepage control to reduce the introduction of contaminants into the local ground water regime. Appendix C presents a summary of a thesis by Lawrence Martin on the analysis of the acid production potential of mill tailings, and the results of geotechnical testing of mill tailings completed by ROM. Appendix D describes potential landfill sites identified within the study area, the development of these sites to meet the present needs of the mining industry and the future requirements of the community is described. Appendix E summarizes the main legislation impacting on tailings disposal. Appendix F discusses the environmental and socio-economic factors that should be considered.

Jan 1, 1981

By William O. Vanderburg

This report 3/gives the results of a reconnaissance of the mining districts in Lander County, Nev., made from March 29 to April 20 and from May 9 to May 21, 1938, during which virtually all of the mining districts n the county were visited. No attempt has been made to include in this report all the mines and prospects in the various mining districts, and it should be stated that whether or not a property is mentioned herein has no. bearing on its merits. The report rovers the situation of the various districts, types of ore deposits, ownership and description of mines and prospects, information on past and current activity, and other information of economic interest likely to be useful to those interested in the development of our mineral resources. The names of the various districts mentioned are those generally used when they were organized for purposes of record and regulation. When originally organized, the districts embraced large areas with no well-defined boundaries, so that the names have little geographical significance.

Jan 1, 1939

By Robert L. Jones

The Boston Consolidated mine is situated in the Bingham mining district, Salt Lake County; Utah (fig. 1). The property has had a noteworthy production of cupriferous, gold-bearing, pyritic ore in addition to lead ore. The Bureau of Mines established a diamond-drilling development project on the property in September 1943 with the primary objective of determining the continuity of a mineralized zone in the Commercial limestone below and to the northeast of the 800-foot level (fig.2). Examination of the geologic feature at the property previous to drilling indicated that the mineralized limestone horizon would continue belay the 800-foot level, but with a flatter dip than disclosed above this level. During the project period, 36 holes totaling 4,001 feet were drilled from underground stations outlining the zone below the 800-foot level (figs. 2 and 3).

Jan 1, 1949

By P. L. Swanson

Stability analyses of fractured and faulted rock masses require delineation of the position, extent, and orientation of geologic discontinuities. The size of the smallest active discontinuity that may potentially be resolved using the spatial distribution of microseismic event locations is Limited by the accuracy and precision of the location methods. At a hard-rock mine in the Coeur D'Alene mining district of northern Idaho, two data sets consisting of calibration blast signals from a known source site and origin time and microseismic event signals were recorded using a stope-wide accelerometer array. These seismic signals are used to quantify various sources of error in event location. Five factors influencing source location errors are examined in this U.S. Bureau of Mines study: (1) biases of the numerical source location techniques, (2) receiver array geometries, (3) uncertainties in receiver positions, (4) errors in picking arrival times, and (5) uncertainties in seismic velocity structure, including the effect of mine openings. In addition, synthetic data (accelerometer positions, travel-time picks and wave velocity) are used to determine the effect of known systematic and random errors on source location calculations. It is shown that the commonly accepted association of minimum travel-time residuals with the best location solution does not necessarily hold true when there is a systematic error in seismic velocity. Recommendations are made for increasing the accuracy and precision of locations of microseismic events detected under similar field conditions.

Jan 1, 2010

By Gary J. Cwick

Mineral resources of the Rice Valley Wilderness Study Area (WSA), in the Mojave Desert of southeastern California, were investigated by the U.S. Bureau of Mines and U.S. Geological Survey during 1980. The study consisted of an examination of mines, prospects, and mineralized areas by the Bureau: of Mines and geological, geochemical, and geophysical investigations by the Geological Survey. Little indicated potential for the presence of mineral resources exists in the valley floor segment of the study area. The Big Maria Mountains section of the study area has some potential for mineral resource development. Decorative building stone from both bedded quartzite deposits and weathered limestone surface rubble (driftwood stone) has been produced from the Big Maria Mountains segment of the study area. Total production is unrecorded but probably small. A 700,000 ton (640,000 t) quartzite resource was inferred and 4,500 tons (4,100 t) of driftwood stone within the study area was estimated. A relatively pure limestone deposit inside the study area contains an inferred resource of 14 million tons (13 million t). One prospect suggests a potential for the presence of manganese resources although none were estimated. The likelihood of discovering oil, gas, coal, uranium or geothermal energy is low; potential sources are not known to exist.

Jan 1, 1982

By Danny A. Riley, James R. Sanger, Hani S. Matloub, Michael Agresti, David Rowe, Lin-Ling Zhang, Yuhui Yan, Paula Galaviz, Judith Marchant-Hanson, Ji-Geng Yan

Until now there has been controversy about which tests should be performed to diagnose early Hand-Arm Vibration Syndrome (HAVS). Initial screening questions, especially about tingling and numbness, routinely given to patients prior to examinations proved to be a very important tool in the diagnostic process1, 4. However, standardized tests that are simple, quick, valid and reliable are needed to support a diagnosis of HAVS. Purpose: To find the most valid and reliable tests to diagnose HAVS. Material and Methods Five major tests were performed on Group I and Group II. Group I: Control group of 12 volunteers including students, nurses, secretaries and physicians with no history of using vibrating tools (age 20 to 50y, mean age 38.5y; 5male, 5 female.) Group II: 12 workers (age 17 to 65y, mean age 39y; 9 male, 3 female) were sent by a local trade union with a history of using vibrating power tools on their jobs for varying amounts of time (mean 12.2y, from 0.5 to 35y.) Pre-enrollment survey showed that each had more than 4 complaints commonly associated with use of vibrating tools (including numbness, tingling, weakness, pain, finger color or nail changes, temperature change, and difficulty moving.) 1. Sensory nerve conductive tests: Amplitude and nerve conductive velocity (NCV) were evaluated. 2. Cold Stress-Temperature recovery time tests were done on the index finger of the dominant hand following these steps: Confirm water bath is within 4-5º C. Place the finger temperature probe on pad of the index finger of the dominant hand. Record temperature every 15 seconds. Place subject’s hand in the cold- water bath for exactly five minutes. Record temperature every 15 seconds for ten minutes. 3. Blood test: Venous blood was taken by a 21-gauge needle with the yellow collection tube adapter. S-ICAM, Sera Thrombomodulin, Norepinephrine levels were evaluated by Henderson Research Centre, Canada. 4. Finger Sensory Evaluation: Semmes-Weinstein monofilament test and 2-point discrimination tests were performed on bilateral fingers. 5. Digital blood pressure test: blood pressure was measured in bilateral index fingers. Results 1. Median nerve sensory conductive amplitude from palm to wrist : GI: mean 96 ± 31µm; GII: mean 43± 30µm; for dominant hands. GI vs GII: P<0.001

Jan 6, 2006